Search Documents

By I. Hague

Support liners for underground applications include steel and timber sets, meshing and lacing, screen/mesh, shotcrete and thin support liners (superskins). Over the past few years, major advances have been made in the design and application of liners; especially shotcrete and thin support liners. For shotcrete in mines these advances include the common use of slick-lines to solve logistics problems, the design of alkali free accelerators, the use of synthetic fibres and the new generation application equipment. The field of thin support liners is a new one but advances have been dramatic. This paper discusses the progress made and the need for standardization in definitions and testing for thin support liners. It concludes that the newer technologies have a huge potential positive impact on the industries, from both safety and cost points of view. Le chemisage de soutènement pour extraction souterraine comprend des cadres d’acier ou de boisage, mailles et chapeau, cribles/mailles, béton projeté et des chemisages minces de soutènement (super-peaux). Dans les dernières années, des progrès considérables ont été fait dans la conception et application des chemisages, en particulier les chemisages de soutènement en béton projeté et les chemisages minces. Pour le béton projeté dans les mines, ces progrès comprennent l’utilisation courante de lignes de minerais broyés fin pour résoudre des problèmes de logistique, la création d’accélérateurs sans alcali, l’usage de fibres synthétiques et d’une nouvelle génération d’outillage. Le domaine des chemisages minces de soutènement est très récent mais les progrès ont été rapides. Cette étude présente les progrès accomplis et discute du besoin de standardisation dans les définitions et les tests pour chemisages minces de soutènement. La conclusion est que les technologies nouvelles présentent un énorme impact potentiel positif sur les industries, du point de vue à la fois de la sécurité et de la rentabilité. Unterstützungsverkleidungen für Untertaganwendungen inkludieren Flecht und Seilwerk, Gitter/Geflecht, Spritzbeton und dünne Unterstützungsverkleidungen (superskins). Während der letzten Jahre wurden grosse Fortschritte im Design und in der Anwendung der Verkleidungen gemacht; besonders bei Spritzbeton und dünnen Unterstützungsverkleidungen. In Bezug auf Spritzbeton in den Gruben schließen diese Fortschritte den allgemeinen Gebrauch von Rutschbahnen ein um Logistikprobleme zu lösen, das Design von alkalifreien Akzeleratoren, den Gebrauch von synthetischen Fasern und die neue Generation von Anwendungsausrüstung. Der Bereich der dünnen Unterstützungsverkleidungen ist neu, aber die Fortschritte sind drastisch gewesen. Diese Arbeit behandelt den erzielten Fortschritt, die Notwendigkeit der Normierung in den Definitionen und in der Prüfung dünner Unterstützungsverkleidungen. Sie kommt zum Schluß, daß die neueren Technologien, sowohl vom Gesichtspunkt der Sicherheit als auch der Kosten, eine sehr große potentielle positive Auswirkung auf die Industrien haben.

Jan 1, 2003

By P. Schutte

It is evident from most admired companies, globally, that they drive key priorities such as teamwork, customer focus, fair treatment of employees, initiative and innovation into their organisations. It is clearly proofed in all the research that the role of the human factor, and therefore human behaviour, is pivotal to companies striving to accomplish goals such as competitiveness, customer delight, high quality, growing productivity as well as a safety-committed work force. The challenge of leadership is to change the worker’s poor perception of safety to an excited, empowered, valued employee who is continuously committed to the achievement of high levels of health, safety and conformance – the challenge therefore is to transform from within. Any work force needs a set of behavioural rules which work for it – including safety rules and critical safety behaviours, which are accepted through involvement leadership, encouragement and support.

Jan 1, 2003

By J. A. Cruise

From 27th to 29th September, The South African Institute of Mining and Metallurgy held a Colloquium on Equipment Alternatives in Underground Mining in Johannesburg. The Colloquium, which was highly successful, was held concurrently with the 1988 Electra Mining Exhibition. Particle characterization The Fourth European Symposium on Particle Characterization is to be held in Nirnberg, West Germany, from 19th to 21st April, 1989.

Jan 1, 1988

Mr Colin M. Spence took office as President of The Federation of Societies of Professional Engineers on 1st July, 1984. Colin Maynard Spence was born in November 1921, and was educated at the Durban Preparatory and High Schools, in both of which he was a Dux Scholar. He graduated from the University of Natal in 1942 with a B.Sc. degree in civil engineering. In 1958 he received a Diploma in Town Planning from the same university. Cessation of Membership In accordance with Clauses 7.6.1 and 12.1 of the Institute's Constitution, Rules and Policy, the following members have been struck off the Membership list.

Jan 1, 1984

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

By Harushige Kusumi, Yuzuru Ashida, Toshiki Watanabe, Toshifumi Matsuoka

ABSTRACT: The technique of various kinds of numerical analysis offered remarkable results to explication of many rock mechanical phenomena. These techniques regarded a rock stratum as a continuum body and solved the governing equation of continuum mechanics by using finite differ-ence method, finite element method and/or others. Using numerical analysis based on continuum mechanics, however, the simulations of destruction phenomena caused by elastic waves and on the other hand, the elastic wave propagation which generated by fracturing events are quite difficult. In this paper, we express a rock stratum by a granular body model and develop a simulation tech-nique can simulate both wave phenomena and destruction phenomena at once. The DEM (discrete element method) simulation results are compared with finite difference solutions of elastic wave equation. Furthermore, we simulate Hopkinson effect by this proposed method. Hopkinson effect is famous as a destruction phenomenon caused by elastic wave propagation. ABRISS: In dieser Studie drücken wird eine Felsschicht durch ein Granularkörpermodell aus und entwickeln eine Simulationstechnik, die sowohl Wellenphänomene als auch Zerstörungsphänomene simulieren kann. Die Ergebnisse der Simulation mit DEM (Diskrete-Elemente-Methode) werden mit denen der Finit-Differenz-Lösung von Gleichungen elastischer Wellen verglichen. Desweiteren simulierten wir den Hopkinson-Effekt mit dieser vorgeschlagenen Methode. Der Hopkinson-Effekt ist als Zerstörungsphänomen berühmt, verursacht durch Fortpflanzung elastischer Wellen. RESUME: Dans cette étude, nous exprimons un lit de roches par un modèle à corps granulaire et développons une technique, permettant de simuler d&apos;un coup le phénomène des ondes et le phé-nomène de destruction. Les résultats de la simulation DEM (méthode d&apos;éléments discrets) sont comparés aux solutions à différence finie de l&apos;équation d&apos;ondes élastiques. En outre, nous simulons l&apos;effet d&apos;Hopkinson par la méthode proposée. L&apos;effet d&apos;Hopkinson est connu comme phénomène de destruction, causé par la propagation d&apos;ondes élastiques.

Jan 1, 2003

By Md. Amanullah

A novel triple action load cell assembly (LCA) was developed to determine three index parameters reflecting compressive, tensile and shear characteristics of mudcakes. The results indicate that the tensile, compressive and torsional behaviour of mudcakes are strongly influenced by the physics and chemistry of the mud additives. Eine neuartige dreifach wirkende Druckkammer zur Bestimmung der drei Indexparameter Druck, Zug, und Scherung von Spülungskuchen wurde entwickelt. Die Ergebnisse weisen auf einen starken Einfluss der physikalischen und chemischen Spülungszusätze auf Druck, Zug, Scherung hin. Un assemblage d&apos;une nouvelle cellule a triple action (LCA) a été développée pour déterminer trois paramètres caractérisant la compression, la contrainte en traction et la résistance á la fracture des cakes. Les résultats indiquent que les comportements tensile, compressif et de torsion des argiles sont fortement influencés par la chimie et la physique des additifs des boues.

Jan 1, 2003

By P. Marinos, G. Tsiambaos, H. Saroglou

The anisotropic behaviour of “Athens Schist” has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the “Athens Schist” were statistically analysed and evaluated. Le comportement anisotropique des roches du système “Schistes d’ Athènes” a été déterminé sur des épreuves avec une orientation différente de la schistosité par rapport à l’axe de chargement sous des conditions axiales, triaxiales et dynamiques. Un grand nombre des résultats a été statistiquement analysé et discuté. Zur Bestimmung der anisotropen Eigenschaften der Athen Schiefer wurden einaxialen, dreiaxialen und dynamischen Kompressionsversuchen an Gesteinskernen durchgeführt, bei denen die Belastungsachse verschiedenen Neigungen gegen die Schieferung hat. Die Messreihen an anisotropen unzerreissbaren Fels Samplen von Athen Schiefer wurden statistisch analysiert.

Jan 1, 2003

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By R. P. King

"A model of the flotation process can be used effectively for design and control. For design purposes it can be used to predict the performance of a large plant from laboratory and pilot plant data. It can be used for control purposes to assess the utility of any proposed operating modification to an existing plant, and it can also be used to determine optimal control settings for best operating performance.A model has been developed that will allow for variations in feed properties and for variations in fineness of grind. The model can be used to assess the effects of reagent addition rate, aeration rate and pulp level on plant performance and these are the control variables that are used individually or together in all operating flotation plants. The model provides for a distribution in the values for flotation rate constants, particle size and mineral fraction, and, because of its complexity, requires a large computer when it is to be applied to a typical plant configuration. The computational method that is used to apply this model to such configurations is described in this paper, and particular attention is paid to the problem of allowing for feedback of tailings from cleaners and recleaners."

Jan 1, 2014

By E H. O Meyer, K van Dyk

Fine powders normally exhibit, to a more or lesser extent, some ability to participate in dust explosions. Zinc dust as used in the extractive metallurgy of zinc, is not known to be a reactive powder in the industry. No evidence could be found in the literature where zinc dust was involved in an explosion or explosive type event. On 3 May 2002 an explosive type incident occurred at Zincor in Springs, South Africa, which led to a fatal accident. Given the history of relative benign behaviour of zinc powders under conditions conducive to dust explosions, it was decided to share the information of this incident with industry in an effort to prevent similar incidents. Therefore, the purpose of this paper is to describe the incident that occurred at Zincor, discuss the major findings, report on corrective actions, as well as publish the results of subsequent tests that were performed to determine the conditions under which zinc powder exhibits explosive characteristics.

Jan 1, 2005

By K. Sugawara, Y. Hirakawa, A. Sato

The rock mass properties such as deformability and permeability are highly dependent on the existence of cracks. The Ratio of Crack Opening Dependency (RCOD) was proposed as a new index to evaluate the deformability of infinite jointed rock mass. The RCOD is defined as the ratio of total amount of crack opening and the total deformation of jointed rock mass. The theoretical relation between the RCOD and the effective compliance of jointed rock mass is discussed and confirmed through two-dimensional numerical analysis by the SC-DDM, together with the applicability to the rock engineering. Les propriétés de masse rocheuse telles que la déformabilité et la perméabilité sont très dépendantes de l&apos;existence de fissures. Le rapport de dépendance d&apos;ouverture des fissures a été proposé comme un nouvel index d&apos;évaluation de la déformabilité de masse rocheuse à assemblage infini. Le rapport de dépendance d&apos;ouverture des fissures est défini comme étant le pourcentage de quantité totale d&apos;ouverture des fissures et de déformation totale de la masse rocheuse assemblée. Le rapport théorique entre le rapport de dépendance d&apos;ouverture des fissures et la compliance efficace de masse rocheuse assemblée sont traités et confirmés au travers d&apos;une analyse numérique à deux dimensions par SC-DDM en même temps que l&apos;applicabilité à l&apos;ingénierie des roches. Die Felsmasseneigenschaften wie Verformbarkeit und Durchlässigkeit sind hochgradig abhängig von dem Vorhandensein von Rissen. Das Verhältnis der Riss-Öffnungsabhängigkeit (RCOD) wurde als neuer Index der Verformbargkeit von infinit zerklüfteter Felsmasse vorgeschlagen. Der RCOD wird als Verhältnis der Gesamtmenge der Rissöffnungen und der Gesamtverformung der zerklüfteten Felsmasse definiert. Die theoretische Beziehung zwischen RCOD und der effektiven Verformbarkeit von zerklüfteter Felsmasse wird diskutiert und durch zweidimensionale numerische Analyse mit SC-DDM bestätigt, zusammen mit der Anwendbarkeit auf Bergbautechnik.

Jan 1, 2003

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

Termination of membership In accordance with By-Law 7.6.1. of the Constitution of the Institute, the names of the undermentioned members have been removed from the membership register. Colloquium and General Meeting A General Meeting and Colloquium on &apos;Heavy-medium separation and ore sorting&apos; was held on 18th September, 1974, at 09h15, in Kelvin House, Johannesburg.

Jan 12, 1975

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

South Africa?s now a member of this body, tailored on the World Bank, and headquartered in Abidjan-Cote d&apos;Ivoire. As a funding agency for capital projects within 59 member countries of the ADB it is to be expected that there are guidelines to the requirements for funding application and for project management and control.

Jan 1, 1996

The annual general meeting of the Branch was held at the St. Helena Club on Thursday, August 21, 1969. Mr J. G. Kirchner (Chairman) was in the Chair. Also present were Mr R. C. J. Goode, President of the S.A. Institute of Mining and Metallurgy; Nine Members: Messrs N. A. Honnet, W. R. Lawrie, J. N. Saunders, D. D. Waterman (Committee Members), M. G. Cullen, G. C. P. Labuschagne, H. A. G. Slater, I. G. Thomas, T. Zadkin and Nine Associate Members: Messrs R. Campbell, D. E. Couperthwaite, T. M. Espach, J. M. Ferguson, G. W. Futcher, A. G. C. Merson, E. R. Penny, R. B. Sutherland, J. W. van den Munckhof and One Visitor: Mr D. J. McLaren. The Chairman declared the meeting open and, on behalf of the Branch, thanked the President for coming from Johannesburg to attend. MINUTES OF THE PREVIOUSGENERALMEETING As the Minutes of the General Meeting held on June 18, 1969 had not yet been published in the Journal, the Chairman moved that their adoption and the discussion thereof be deferred to the next General Meeting. This motion was adopted unanimously. CHAIRMAN&apos;S ANNUAL REPORT 1968/69 At Mr Kirchner&apos;s request, Mr. R. C. J. Goode took the Chair during the presentation of the Chairman&apos;s Annual Report. (This report was published in the August 1969 issue of the Journal.) OFFICE BEARERS AND COMMITTEE MEMBERS FOR THE YEAR 1969/70 The Chairman announced that the outgoing Committee had elected the following office bearers for the coming year: Chairman: N. A. Honnet; Vice-Chairman: J. N. Saunders; Immediate Past Chairman: J. G. Kirchner. The Chairman then read a letter from the scrutineers reporting that the following had been elected to the Committee: M. S. Grobler, W. R. Lawrie, L. O. W. Leimer, A. T. Lewis, R. S. Pearson, T. Zadkin. The Chairman thanked the scrutineers for their services, and congratulated Messrs Lawrie, Leimer and Zadkin on their re-election and Messrs Grobler, Lewis and Pearson on their election to the Committee. The Chairman announced that he had heard, with regret, that Mr. T. Zadkin would be leaving the O.F.S. at the end of August, 1969. Mr Zadkin had served on the Committee continuously since the inception of the O.F.S. Branch and records showed that he had only failed to attend three General Meetings in over nine years. The Chairman expressed the gratitude of the Branch for Mr Zadkin&apos;s invaluable services to the Institute, congratulated him on his well earned promotion and wished him well in his new position. INDUCTION OF CHAIRMAN The Chairman introduced Mr N. A. Honnet to the meeting by briefly outlining his past career and, after congratulating him on his election, called upon him to take the Chair. In congratulating the out-going Chairman on a very successful term of office, Mr Honnet said that due to the absence of many Committee Members for a large portion of the year Mr Kirchner had carried a heavy burden, and he moved a vote of thanks and appreciation for Mr Kirchner&apos;s efforts. This was carried unanimously. GENERAL BUSINESS There were no points raised under this heading. MINING AND METALLURGICAL CONGRESS The Chairman called on Mr W. R. Lawrie to give his talk on aspects of the Mining and Metallurgical Congress recently held in Britain. This presentation was illustrated with photographic slides and proved of great interest to Members. Mr D. D. Waterman proposed a vote of thanks to Mr Lawrie and the Chairman then asked Mr R. C. J. Goode to contribute to Mr Lawrie&apos;s address. Mr Goode thanked Mr Kirchner for his efforts during his very successful term of office and congratulated the in-coming Chairman and Vice-Chairman on their election. He then gave a brief talk on aspects of the Congress not dealt with in Mr Lawrie&apos;s address. These included the industry&apos;s requirements of graduates, the necessity of their rapid advancement and the desirability of sending such young men to attend future Congresses. Mr Goode announced that two symposiums will be sponsored by the Institute next year, one on Tunnelling and the other on Open Cast Workings.

By V. Labiouse, R. Gärber

The paper aims at clarifying the up-to-now misappreciated role taken by pore water on the design of deep tunnels in saturated porous media. Numerical simulations with a non-dimensional FEM-model emphasise the influence of pore water characteristics (in situ pressure and compressibility) and boundary conditions (lining permeability) on the short and long term underground-structure equilibrium states. These results cannot be achieved by means of monophasic total stress analyses. Dieser Beitrag untersucht den Einfluss des Porenwassers auf die Dimensionierung von tiefen Tunnelbauwerken in wassergesättigtem Untergrund. Numerische Simulationen mittels eines dimensionslosen FEM-Modells betonen den Einfluss der Porenwassereigenschaften (in-situ Druck und Kompressibilität) und der hydraulischen Randbedingungen (Tunnelausbaudurchlässigkeit) auf Kurz- und Langzeitverhalten des Untergrund-Ausbau Gleichgewichts. Diese Ergebnisse können nicht ermittelt werden anhand von Einphasen- und Totalspannungsmodellen. L’article s’intéresse au rôle méconnu de l’eau interstitielle dans le dimensionnement de tunnels profonds creusés dans des milieux poreux saturés. Des calculs adimensionnels par éléments finis soulignent l’influence des caractéristiques de l’eau interstitielle (pression in situ et compressibilité) ainsi que des conditions aux frontières (perméabilité du revêtement) sur les équilibres court et long terme de l’ouvrage. Ces résultats ne peuvent pas être obtenus par des calculs en contraintes totales.

Jan 1, 2003

High pressure grinding technology has gained further interest in various industries. So far in the mining industry, machines are in operation in diamond mines and iron ore applications. In gold and copper ore processing, test work has been conducted showing considerable operational and process benefits. Similar benefits can be expected from HPGR applications in the platinum industry due to the preferred ore breakage along grain boundaries, thus liberating the PGE particles. This paper will provide an update on the state of high pressure grinding roll technology. Developments in the design of high pressure grinding rolls, for minimized maintenance requirements and availability just as high as conventional mills, will be presented. Plant flow sheets and concepts will be discussed, which allow for a reduction of capital and operating cost in comparison to existing two-stage milling circuits.

Jan 1, 2004

By R. P. H. Willis, A. G. du Plessis, R. B. Wilson

This paper reviews issues to be considered in choosing primary access and transportation options for platinum and other mines. It proposes appropriate criteria and a methodology for deciding on the optimum primary access option for any particular orebody. Also included are generic parameters that can be used to facilitate the process of choosing the optimal access option.

Jan 1, 2004