Search Documents

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By Robert J. Evans

Capital and operating costs were estimated using a wet suppression, fabric filter, and a combination system of the two for hypothetical hard rock stone crushing plants located in central Pennsylvania, operating at 300, 600, and 1,000 tons per hour. Fixed capital expenditure for the dust abatement systems ranged from $49,129 to $249,162. Annual operating costs for the dust abatement systems ranged from $8,394 to $46,606 (0.9 to 3.2 cents per ton). If these dust abatement systems are properly sized, installed, and maintained, efficiencies approaching 95 percent can be expected for reduction in weight of dust particles emitted before control.

Jan 1, 1975

By W. T. Culler

"The ""rate-of-preduotion curve"" described in the revised Treasury Manual* was devised by the author in May, 1920, and since that time has been use by the oil and gas valuation section of the Treasury Department in determining the rate of production of wells for purposes of taxation. This curve is most useful for estimating the future production of a well, or group of wells, of known daily settled production, where future-production curves and tables based on yearly production records are available. It also provides a means for determining the past year's production of a well of known daily settled production, or conversely, the estimated production on any day for a well of known yearly production.The rate-of-production curve is auxiliary to the production decline curve and is derived from it in estimating the future production of a tract, a production decline curve formed from the records of the tract itself should be used. If such records are not available, and there is no information which leads to the belief that the average production decline of the wells in this tract differs from the average for the pool or district, an average curve for the pool or district may be used.The accompanying chart illustrates a typical rate-of-production curve, with the yearly production decline curve from which it is derived. The production decline curve shown is for an average well in the Augusta district, Butler County, Kansas, and has been constructed from the tables given on page 128 of the revised Treasury Manual.The ordinate (vertical scale on the chart) of any point on a yearly production decline curve represents the production of the well during the year previous to the date shown by the abscissa (horizontal scale). For example, the chart shows that an average well, which produced 100,000 barrels of oil in 1915. produced 92,000 barrels in the year previous to January 19, 1916, produced 53,300 barrels in the year previous to June 1, 1916; produced 49,000 barrels in the year previous to July 1, 1916, 27,000 barrels in 1916, and 10,000 barrels in 1917."

Oct 1, 1921

By John M. Gomes

The Bureau of Mines investigated two techniques for removing CaO from scheelite (CaW04) prior to electrolysis. In the first technique, a crude tungstic oxide (WO3) containing 0.15-percent lime (CaO) was prepared by digesting scheelite concentrates in hot hydrochloric acid. This oxide was used as cell feed to produce tungsten of 99.9-percent purity. The second technique used a high-temperature, two-phase separation, resulting in extraction of 99 percent of the WO3 in the halide-tungstate phase, while 90 percent of the CaO was retained in the silicate phase. Tungsten of 99.9-percent purity was deposited from the halide-tungstate melt after B203 and NaPO3 were added to form an electrolyte. The two methods were compared with a previously developed technique of depositing tungsten from scheelite concentrate fed directly to the electrolytic cell.

Jan 1, 1971

By J. M. Singer

Flame propagation of lower limit hybrid coal dust-methane-air mixtures in vertical and horizontal flame ducts of 15.2 cm id and 1.8 m length has been investigated to provide information bearing on safety in mines. Fuel concentrations at lower limits of flame propagation and equivalences of coal dust and methane are much higher for continuing flame propagation than for short-span flame propagation in the vicinity of an "overdriving" ignition source. As the energy of the ignition source was increased, the flame speed and the distance of flame propagation from the ignition source increased, whereas the total fuel concentration at the lower limit decreased.

Jan 1, 1968

By D. L. Sawyer

Aqueous C12-02 leaching procedures developed by the Bureau of Mines to produce zinc chloride from zinc sulfide bulk concentrates were effective in extracting 99 pct of the zinc and 97 pet of the silver contained in samples of massive seafloor sulfides from the southern Juan de Fuca Ridge. Zinc sulfide (sphalerite and wurtzite) mineralization comprised 55 and 88 pct of two specimens provided by the U.S. Geological Survey for this study. Minor occurrences of galena, chalcopyrite, and other minerals in the sulfides permitted the recovery of pregnant liquors that were low in metal values other than zinc, which were successfully purified by a two-step cementation procedure using zinc dust.

Jan 1, 1983

By D. J. Bauer

This report covers a phase of an extraction project carried out as part of a research program on rare-earth technology. The current project--the production of pure cerium compounds--is an intermediate step between ore processing and metal reduction. In this connection, a study on a separatory-funne1 scale was made on nonreducing extractants for recovering cerium (IV) from tri-n-butyl phosphate (TBP) and of methods for recovering the cerium nitrate from the strip solution. Dilute sulfuric acid was found to be 100 percent effective in stripping cerium (IV). Several precipitants were effective in recovering the cerium from the strip solution, and ethanol was especially promising. A scaled-up investigation was made into the use of spray-tower type equipment to perform the function of extracting, washing, and stripping. This equipment, referred to as the pressure-bubbler, utilized the system developed on the separatory-funnel scale. Feed solutions were prepared from a bastnasite concentrate by two techniques. Of these, the sulfated bastnasite solution was most successful, resulting in 86-percent recovery of the cerium at 99.7+-percent purity.

Jan 1, 1959

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By M. Clair Smith

This report is one of a series describing exploration, development, mining, and processing of mineral deposits in the United States. The reports are prepared and published by the Bureau of Mines in cooperation with various mining companies The purpose of the reports is to promote development and conservation of our natural reserves by disseminating technological information on mining and milling procedures and related practices at operating mines. Simplot Silica Products, Inc., mines and processes a friable silica sandstone. The finished products are sold for use in glass manufacture, foundries, chemicals, and special applications.

Jan 1, 1959

By D. Hinton, M. McCawley, R. C. Lantz, F. Pisano, C. Stanley

"INTRODUCTION Aerosols (5 um have not been shown to be consistently generated and characterized in inhalation chambers. Particle deposition in the lungs however may occur with particles as large as 25 um(1). Therefore, in order to closely simulate the atmosphere of an underground coal mine where the distribution is bimodal, with modes at S and 15 um (2), particles much greater than <1 um must be characterized for uniform mixing and size distribution within these chambers. The Hazelton Animal Exposure Chamber has been chosen because it has been best characterized for smaller particles (<1 um) (3), and is the major type used by most inhalation toxicology institutes such as Lovelace Inhalation Toxicology Institute and Battelle Northwest Laboratory.BACKGROUNDPreviously published studies on the inhalation of solid aerosols have attempted to characterize the distrition of particles of <2 um in diameter. There are no published reports of extensive work characterizing either the size distribution of particles <1 um or the concentration throughout the exposure chamber (Table 1).Table 1 shows the variability and sizes of several aerosols <1 um in diameter used in five previous chamber studies.Discussion of Previous StudiesThe study done by Bauermash, Bryan, Dickinson, and Burke (4)stated two major concerns in the development of the 6.5 ft. diameter chamber. The first was that a quantity of animals could be exposed to the same concentration regardless of the location of the animal, and second was that the chamber could be easily cleaned and decontaminated. The solution to the first concern required a circular chamber with the contamination air entering the chamber somewhere along the central axis. The animals could then be changed during exposure time so that each animal was exposed throughout the total volume."

Jun 1, 1988

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By G. St. J. Perrott, N. A. Tolch

"PURPOSE OF TESTSThe propulsive strength4 developed by the Cardox blasting device depends on the thickness of disk, weight of heater element, and weight of carbon dioxide charge. It might be supposed that the maximum weight of carbon dioxide that can be charged into the shell should give the greatest strength. However, according to the ballistic pendulum, the maximum weight of carbon dioxide with certain conditions of heater and disk has less propulsive strength than a smaller charge; in one condition of test a loss of 39 per cent in propulsive strength was noted. It is therefore of interest to study the effect of the variables that determine the strength of Cardox.ACKNOWLEDGMENTGrateful acknowledgment is made to A. B. Coates, associate mechanical engineer who developed the testing method for measuring pressures in the Cardox shell.DESCRIPTION OF DEVICEThe Cardox blasting device as fully described by the bureau in Report of Investiga¬tions 2920 (1929), consists essentially of hollow—steel shell, cylindrical in shape, an electrode, valve assembly, shearing disk, and discharge cap. The shell is prepared for use by inserting a heater element, closing the open end with a shearing disk, and screwing in place the discharge cap. The charge of carbon dioxide enters the shell through the electrode.The heater element is fired by an electric igniter of the match—head type. The heat released by the heater element completely gasifies the carbon dioxide and raises the pressure of the gas until it is enough to shear the disk."

Apr 1, 1931

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

By F. P. Haver

The Federal Bureau of Mines investigated aqueous electrolysis as a means for reducing lead chloride prepared by ferric chloride leaching of galena concentrate: NaC1 PbS + 2FeC13 ? PbC12 + 2FeC12 + S°. During electrolysis, metal was produced from solid lead chloride in contact with the cathode rather than from lead in solution. Relatively high current densities--up to 300 amp/ft2--were possible when operating in this way. A very simple cell, having a horizontal lead cathode at the bottom and a vertical graphite anode at the top, was employed. Lead chloride crystals, covering the cathode, were converted to metal powder during electrolysis, and chlorine gas or FeCls was produced at the anode, depending on the electrolyte composition. Electrolytes tried included aqueous solutions of HCI, NaCl, NH4Cl, and FeC12-NaC1. Optimum results (96-pct current efficiency, 0.23 kwhr/lb Pb) were obtained with 20 pct HC1 at 25° C, using a current density of 15 amp/ft2 and an electrode spacing of 1 inch. When the current density was increased, the energy requirement increased also but only to 0.41 kwhr/lb at 150 amp/fr3 and 0.58 kwhr/lb at 300 amp/ft2.

Jan 1, 1978

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By Raymond M. Stateham

Calculations based on data obtained from measurements of smoke from coal-fired powerplants predict that infrared imagers will be useful tools for smoke vision. Infrared imagers operating in the 3-to 5-um spectral region have been evaluated for this purpose. A mine opening 110 meters long was filled with smoke from burning coal, and two men, wearing breathing apparatuses, moved through the smoke to serve as targets. The men were detected and identified at 80 meters.

Jan 1, 1976

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

By R. M. Santmyers

This paper represents one of a series of digests of foreign mining legislation that is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the mining legislation of Tunisia was prepared from a copy ( in French ) of the Mining Decree of Tunisia promulgated December 29 , 1913 , by the Resident General of France in Tunisia and effective January 1 , 1914. It is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers , to whom it will be referred through the courtesy of the Department of State .

Mar 1, 1933

By E. B. Swanson

Atlantic seaboard refining and marketing companies , dependent largely upon other producing and refining areas for the crude and refined petroleum needed to meet the demand for petroleum products within the Atlantic Coast States , reported an increase in 1929 receipts of 2,542,000 barrels of crude petroleum and 13,479,000 barrels of gasoline over the quantities received during the preceding year . The relatively large expansion in gasoline receipts undoubtedly resulted from the unexpected increase in gasoline consumption which characterized the petroleum industry during 1929. Gasoline receipts from California increased 6,354,000 barrels and shipments from foreign countries were 5,381,000 barrels in excess of the 1928 figures , while receipts from Gulf Coast ports , the major source of outside supply, declined 811,000 barrels . Shipments of domestic crude oil by tanker from Gulf Coast ports during 1929 continued the average annual increase of approximately 7,000,000 barrels which has been recorded during the five years of this annual survey . These shipments have increased from 72,556,000 barrels during 1925 to 99,828,000 barrels during 1929. Shioments of Mid- Continent crude by pipe- line to Atlantic Coast refineries have , on the other hand , dropped from 11,903,000 barrels in 1925 to 1,409,000 barrels during 1929. Receipts of foreign crude oil declined 1,461,000 barrels from the preceding year . : Gasoline demand within the Atlantic Coast area reached a total of 123,345,000 barrels , an increase of 15.7 per cent over 1928. Gasoline production increased 4,157,000 barrels , while tanker receipts were nearly 11,000,000 barrels larger than in 1928. Indicated shioments from Appalachian refineries were somewhat larger than in the preceding year . Gasoline production showed an average of 33.5 per cent of the crude throughout , as compared with 31.5 per cent in 1928 and 32.7 per cent in 1927. Cracking operations accounted for 44.6 per cent of the gasoline produced , as compared with 40.6 per cent in 1928 and 35.3 per cent in 1927. Gas oil and fuel oil production averaged 52.8 per cent of the crude throughput , as compared with 55.1 per cent in 1928 and 49.5 per cent in 1927 , the decline reflecting the smaller quantities of foreign crude refined during the year .

Nov 1, 1930