Search Documents

By Robert C. Hickman

In its search for strategic minerals, the Bureau of Mines investigated the Rutherford Mine property in Amelia County, Va. The property was visited by F. W. Horton, mining engineer, and Margaret Fuller Boos, mineral technologist, of the Bureau of Mines, in company with Eugene Dawson, of the War Production Board, on July 16-11, 1943. An exploration program by the Bureau was recommended, and work was started on July 28, 1943, and continued until September 16, 1943. A total of 1,250 feet was diamond drilled in 5 holes on the property.

Jan 1, 1950

By K. C. Dean

Time and motion studies were made by the Federal Bureau of Mines on the hand and machine dismantling of scrapped auto starter motors, generators, and alternators for recovery of copper, aluminum, and iron. The studies showed that an individual with power handtools and convenient access to a hydraulic press, power bandsaw, acetylene torch, and power lathe could, in an 8-hour day, disassemble about 100 starters, or 150 generators, or 30 alternators. The scrap copper yield would be 280, 390, and 45 pounds, respectively, and the iron yield would be about seven times the copper weight. About 100 pounds of aluminum would be obtained from the alternators.

Jan 1, 1976

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By Spencee L. Willett

In 1986, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied a 51, 160-acre portion of the 107,920-acre Diablo Mountain Wilderness Study Area (OR-001-058) in order to evaluate its mineral resources. The study area is located 1n Lake County, OR, about 45 miles northwest from Lakeview. The study area is located near the northwest corner of the Basin and Range physiographic province. Tertiary Picture Rock basalt with tuff interbeds underlies the area (Travis, 1983). No mineral resources were identified; no mines, prospects, claims, or mineralized areas exist in or adjacent to the Diablo Mountain study area.

Jan 1, 1987

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By Foster Fraas

A separator for minerals of low magnetic susceptibility and fine particle size in a water suspension is described. A ring-shaped matrix of ferromagnetic fragments rotating so as to pass successively through magnetic-field and field-free regions provides for the separation. Application is illustrated in the separation of hematite and ilmenite from quartz.

Jan 1, 1966

By Jr. Sharkey

The Bureau of Mines investigated gases from flash and laser irradiation of Pittsburgh seam (hvab) coal to determine the action of high temperatures on coal. Temperatures in excess of l,000° C were reached with both types of irradiation. Craters about 300 microns in diameter were produced in the coal with millisecond pulses from the laser unit rated at 1.7 joules' output. Gaseous products from laser and flash irradiations in vacuum contained 21 and 8 percent acetylene, respectively. Diacetylene, vinylacetylene, and other products to molecular weight 130 were indicated in the mass spectrum of the gas from the laser study. Single experiments were also conducted in which the laser energy, particle size of the coal, and atmosphere were varied. The results indicated that the distributions of products obtained from the flash and laser irradiations of coal were different from that produced in high-temperature carbonization.

Jan 1, 1966

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By Marcia L. Harris

The National Institute for Occupational Safety and Health (NIOSH), as part of its continuing research program for evaluating coal dust explosion hazards, has investigated several areas in which current practices may need to be updated in order to adequately protect mines against coal dust propagated explosions. In the United States, current rock dusting requirements remained largely unchanged since 1969. US Title 30 Code of Federal Regulations Section 75.403 is based on a coal dust particle size survey performed in the 1920s and later was supplemented by full-scale testing of the rock dust ability to inert a coal dust explosion. NIOSH recently conducted a comprehensive survey of US underground coal mines to determine the range of coal particle sizes found in dust samples collected from the mine entries. Due to advancements in technology and modern coal mining techniques, the current coal dust particles in intake airways are significantly finer than those found in the mines in the 1920s. According to past full-scale dust explosion test results, the current rock dusting practices used in today?s mines to inert a coal dust explosion may not be adequate. Other closely related issues such as rock dust testing methods and sampling procedures are discussed.

Jan 1, 2009

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939

By Walter R. Storms

The Iron Mountain tungsten deposits first were visited by a field party of the Federal Geological Survey in May 1942 while beryllium deposits in that district' were being examined . Later they were examined by F. A. Rutledge , an engineer of the Bureau of Mines , and an exploration project was recommended , work upon which began in March 1943 and was terminated in April 1943 after intensive trenching and sampling had been completed .

Mar 1, 1947

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By K. K. Kelley, L. B. Pankratz, W. W. Weller

Mullite is a substance of prime importance in ceramic technology . Despite this fact , its thermodynamic properties have received little attention . A Bureau of Mines literature survey disclosed the absence of lowtemperature heat capacity data , the absence of an experimental entropy value for 298.15 ° K , and the lack of heat content data beyond the temperature range from 298° to 576 ° K. Data supplied in this Bureau report fill these gaps in the thermodynamic knowledge of mullite . According to equilibrium phase studies of Aramaki and Roy ,3 the mullite phase melts congruently at 2,123 ± 15 ° K , and the equilibrium crystallinephase composition extends from Al Si2013 to Al6.8 Si₂ Q4.2 . The results in this report are for the stoichiometric composition , Al Si¿Qз . • Heat capacity measurements were made over the temperature range from 50 ° to 298 ° K , and the entropy at 298.15 ° K was evaluated . Heat content measurements covered the temperature range from 298 ° to 1,800 ° K. Heat content

Jan 1, 1963

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By W. D. Mcmillan

Soapstone is the term applied to an impure, massive, soft rock with a greasy feel. It is of variable composition, consisting chiefly, however, of talc, tremolite, and chlorite. Although limited quantities of soapstone are used as building material, in fireplaces, and in the manufacture of laundry tubs, sinks, laboratory-table tops, and-oven and furnace blocks, the principal part of the production is ground for use in roofing paper, insecticides, and as a filler in asphaltic paints.

Jan 1, 1949

By Perry G. Cotter

The borides of the transition metals in Groups IV and VI exhibit, in addition to a certain degree of hardness, considerable resistance to heat and oxidation. They have high melting points (1,850°-3,060° C.) and low coefftcients of thermal expansion and can be bonded with other materials and hot-pressed to desired shape (cermets). Suggested uses for the borides include use in rockets and jet engines, as thermocouple protection tubes, as containers for molten metals in die casting, as flame-plated coatings on less refractory compositions to prevent erosion by hot gases, and as control rods and neutron shielding material in nuclear engineering, The Federal Bureau of Mines investigation of zirconium diboride started in 1950 at the Boulder City Nev,, Metallurgy Research Laboratory, Its purpose was to reduce the cost of raw materials for the production of zirconium diboride.

Jan 1, 1961

By Edward D. Thimons

The Bureau of Mines has developed a damage-resistant brattice, intended for use as a stopping in locations where blast damage to stoppings is a problem, the roof is relatively flat, and the differential pressure across the stopping is not high. Damage-resistant brattices consist of a series of vertically hung brattice panels joined to each other by Velcro connections that improve the airtightness of the brattice. When the brattice is subjected to strong blast forces, the Velcro connections peel apart, allowing the panels to open without incurring damage. The Velcro connections can then be resealed in a matter of minutes. A preliminary test in the Bureau's Safety Research Mine and subsequent long-term testing at the White Pine copper mine in Michigan and the Retsof salt mine in New York show that damage-resistant brattices withstand blasting better than conventional stoppings, while still performing as efficient air barriers when the Velcro connections are sealed.

Jan 1, 1978