Search Documents

By S. L. May

Investigations by the Federal Bureau of Mines indicate that hafnium and zirconium compounds of acceptable purity can be extracted from Nigerian zircon concentrates. Chlorination and caustic soda fusion techniques were used to extract 85 to 95 percent of the valuable metals from the concentrate. The extracted hafnium and zirconium compounds were purified by recrystallization of the oxychlorides or by formation of complex salts during chlorination. The zirconium-hafnium product of the recrystallization method contained 15 parts per million of uranium, and the product of the salt-complex method contained less than 10 parts per million of uranium. The hafnium was separated from zirconium by solvent extraction methods. A zirconium product containing 0.3 percent hafnium and a hafnium product containing 4 percent zirconium were obtained. At the request of the Atomic Energy Commission (AEC), work was started to develop techniques for processing Nigerian zircon concentrates in commercial installations presently engaged in producing zirconium and hafnium metals from ores. The Nigerian zircon has a high hafnium content, but the presence of uranium and thorium is a problem not normally encountered in processing zircon concentrates.

Jan 1, 1961

By S. L. Ausmus

The work covered in this report is a continuation of an earlier feasibility study by the Federal Bureau of Mines and points out improvements in the skull-melting method for casting reactive metals such as titanium, zirconium, and hafnium. Machined graphite molds with laminated sections can be reused many times. Large tube sections can be produced by spin casting. Graphite powder is the best expendable mold material, but binders for this use must be compounded carefully. The effects of current and furnace atmosphere on the dependent variables of the casting technique are shown. Because of developments in casting technology for titanium which eliminate the basic problems of melting and pouring the metal, opportunities for improvement in the method have increased. The mold material and gate and riser configurations require particular attention. The limits of application of the casting method have yet to be defined. New knowledge in anyone of these areas could result in marked improvements and simplifications in casting methods.

Jan 1, 1960

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By M. K. Quinn, N. P. Reddy, A. W. Khair

"An analysis of coal fragmentation due to the action of a continuous miner is presented. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). The rotary coal cutter provided the versatility of varying the operating and in-situ parameters to provide information on the effects of generating 37 pm (0.0015 in) particles. In these tests, coal blocks with an approximate dimension of 50.8 x 35.6x 20.32 cm (20x 15x 8 in) were first subjected to confining pressures equivalent to in-situ conditions. The blocks were then cut by the rotary cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as (1) penetration of bit into coal, (2) penetration resistance (thrust and cutting pressures), (3) rotating velocity of' cutting head, and (4) acoustic emission activity in the coal block were monitored. During the test, all the cut products were collected for size distribution analysis. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using a camera attached to an optical microscope.The results led to a better understanding of the mechanisms of the fragmentation process during coal cutting and the effect of operating parameters, in-situ conditions and coal type on the size distribution of the cut product:"

Jan 1, 1989

By A. L. Engel

This report is a compilation of the results of preliminary tests on ores containing scheelite (calcium tungstate). In most of the ores, scheelite was the only value; but several samples contained other values, such as gold, base metals, or, in one instance beryl. These investigations were made to assist the development of domestic tungsten resources by establishing satisfactory treatment methods suitable for small-scale operations. The samples were obtained through the Mining Division of the Bureau of Mines and represent, for the most part, newly discovered deposits. A previous report2/ discussed laboratory test procedures. A less detailed description of test procedures is included in the present report. As is usual in an investigation of this type, only a limited amount of work was done on most of the samples to indicate the results that could be expected from simple treatment of the particular ore. The occurrence of scheelite and the texture of the minerals present differ greatly in individual ores and must be determined and considered in establishing such details of treatment as grinding to obtain optimum liberation of the minerals, the preferred type of gravity concentration, or possible further treatment by flotation.

Jan 1, 1954

By J. R. White, S. W. Lambert, C. M. McCulloch

Examination of several coalbeds in Walker County, Ala., Cambria, Greene, and Fayette Counties, Pa., and Raleigh and Wyoming Counties, W. Va., indicates that cleat orientations are similar throughout a vertical sequence of strata. Studies of cleat orientation were carried out in underground mines that are operating in separate coalbeds vertically above one another. The data show that over a vertical separation of 100 to 400 feet, the average difference in coal cleat orientation between mines is 04° for the face and 08" for the butt cleat. Variations of coal cleat direction between coalbeds examined in strip-mined areas show similar values. Cleat orientations measured at outcrops agree well with the directions measured underground, suggesting that the amount of vertical separation between coalbeds has little effect on the resulting differences in cleat directions. The largest variation of cleat directions between adjacent coalbeds occurs where a large horizontal distance separates two sample locations. Cleat orientations for deeper coalbeds are most reliable where the data are taken from directly above.

Jan 1, 1976

By S. G. McAnally

This is one of a series of papers describing mining and crushing methods and costs at cement plant quarries throughout the United States and deals directly with the methods employed and costs obtained at the Reliance quarry of the Giant Portland Cement Co. at Egypt, Pa., although it is more or less descriptive of the methods used throughout the Lehigh Valley cement district. Systems of transportation vary according to local conditions, such as proximity to the mill, depth of quarry floor with relation to the mill level, etc. Methods of prospecting differ mainly in the type f drills used. Systems of storage, crushing, and grinding vary chiefly in the types of units. ACKNOWLEDGMENTS Most of the information regarding the early history of the Lehigh cement district was obtained from the History f the Portland Cement Industry of the United States, by Robert W. Lesley, the first president of the Portland Cement Association. The writer is indebted also to Charles Clader, Giant Portland Cement Co. quarry superintendent, for valuable information regarding present and past methods and equipment.

Jan 1, 1931

By Paul G. Swanson

This manual of practice is to be used in combination with the final reports for the study of spoil stability in the Eastern Coal Province. The manual applies the predictive matrices developed in the parent study for use in evaluating the stability of typical mine spoil slopes. The values of internal friction and pore pressure coefficient are derived for many varied slope conditions. The results can be used in conventional stability analysis equations to assist the mine operator or regulatory personnel in evaluating spoil stability from very limited information.

Jan 1, 1983

By John R. Bitler

The Bureau of Mines conducted this study to provide information concerning the availability of and the demand for construction-mineral aggregates in the Baltimore, Md., Standard Metropolitan Statistical Area (SMSA). The demand is discussed with reference to the area's current consumption and estimates of the area's demand for aggregates through 1990. Estimates of aggregate supply are presented in conjunction with an examination of the geology of the area, the availability of substitutes, and the effect of transportation costs. A discussion of the constraints affecting aggregate availability precedes the conclusions and recommendations. The availability of aggregates is subject to geologic, economic, and political constraints. As of January 1974, an estimated 20,100 million tons of stone was available to meet the demand projected through 1990 (188.7 million tons). An estimated 139 million tons of sand and gravel was available to meet the demand projected through 1990 (84.3 million tons). Several alternative actions are available within the area to insure the adequacy of the stone supply and to increase the supply of sand and gravel: (1) The establishment of special mineral resource zones; (2) the application of sequential land use techniques; and (3) the exploration of previously undeveloped regions.

Jan 1, 1975

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general, the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By G. W. Grove, O. V. SIMPSON

During the years 1945, 1946 , 1947 , and up to July 1, 1948, only one death was caused by mine fires in bituminous - coal mines of the United States . The one fatality occurred in an Illinois mine in December 1945, and , therefore, there had been a period of 2-1/2 years in which no deaths occurred as the result of mine fires . Moreover, 1946 was the first year since 1930 in which no deaths occurred from mine fires . This record is markedly better than that of 1944 , when 89 fatalities and great property damage were caused by mine fires in bituminous - coal mines and 16 additional men were killed by an explosion that occurred while they were attempting to seal a mine fire .

Apr 1, 1949

By Alton B. Cook

Equipment has been designed and fabricated for study of the vaporization of oil during gas-cycling operations, A sand-packed steel tube, which can be rotated to minimize gravity drainage, is used as a model oil reservoir. A minute windowed cell at the discharge end of the tube through which the liquid-gas interface may be observed, makes possible the separate removal of produced free gas and gas-saturated oil. The operation of the model oil reservoir, and auxiliary equipment, are described by use of a schmatic flow diagram. Details of the specially designed equipment are illustrated by isometric and pictorial drawings, and a description of the experimental procedure is given.

Jan 1, 1959

By Alan R. Buehler

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 256,430-acre Alvord Desert and part of the 22,240-acre East Alvord Wilderness Study Area (OR-002-074 and OR-002-073A, respectively), in order to evaluate their identified mineral resources. The study areas are located in Harney and Malheur Counties, OR, about 25 mi northeast of the small village of Fields. There are no mines, prospects, or identified mineral resources inside the study areas. Basalt flows within the study areas contain chalcedony-lined vugs and banded agate which may be of interest to rock hounds. An ignimbrite flow contains perlitic material, but crystalline contaminants make it unsuitable for commercial uses. Lacustrine (lake) sediments contain diatomite and clays, and evaporite crusts contain boron too low grade to profitably mine. Small quantities of common opal and petrified wood occur which might be of possible interest to rock hounds. Some of the petrified wood is black, free of fractures, and polishes well; it may be suitable as backing material for soft, thin, and brittle gemstones, such as precious opal. The lacustrine sediments also contain black, fetid layers which have above background, but economically insignificant concentrations of zinc, cobalt, nickel, barium, iron, manganese, aluminum, and potassium. Large quantities of fine-grained dune sands within the study areas are too far from markets for economic consideration. Ephemeral streams in the study areas contain small amounts of placer gold of no economic interest. The western portions of both study areas are reported to have moderate favorability for occurrences of natural gas, and both study areas are reported to have high favorability for the occurrence of geothermal resources. As of December 1986, oil and gas leases covered 3,100 acres in the study areas.

Jan 1, 1987

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By Gerald R. Smith

Because of continuing concerns regarding the effects of cumulative quantities of materials in the environment, the Bureau of Mines has initiated a series of studies to evaluate, to the fullest extent possible, all aspects of the materials flow sequence fur selected commodities. Although tungsten and its compounds do not pose a significant health hazard to the environment, they do represent valuable resource materials to which appropriate conservation considerations must be given. The present study includes a description of recent trends in the consumption, loss, and recycling of tungsten-containing materials in the United States during the period 1974 to 1991 and an estimation of the cumulative loss of tungsten to the environment since 1910. Obsolete tungsten is recycled primarily as cemented tungsten carbide components that have been used in cutting and wear-resistant applications. The quantity recycled, as a of annual U.S. consumption of tungsten, was estimated to have increased from 10% in 1974 to 341a in 1991. An estimated 58% of the 148,000 metric tons of primary tungsten consumed since 1910 was lost to the environment through means such as dissipation, discard, and dilution.

Jan 1, 1994

By Charles Findlay, Stephen Krickovic, J. E. Carpetta

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By C. F. McCarroll

[Laboratory research and, control in the u?odnction an; utilization of petroleum and its product s have eqLmde& greatly during the past decade, rind much of the routine control and experimental equipment noirr requires the con-stant daily use of liquid nercury. In spite of this greater use, very little consideration has becn given to the hazard that might be occasioned by the toxic vapors of mercury unavoicl.a~l.p spilled or otherwise exposed to the atmosphere during the normcl 2rgced1u.e of ln30r~tor;~r operations. A sfmple visual exami~stion gf' sone of the laborztories reveals the prescnce of a considerable quantity of mercury in the craclcs of floors, on work tebles, ad on and mo7md eql~ipmeilt st.ads. Usually this yercurj ie contaminated with oily and dirt BO th~t it remint; in R finely divided state and a srnarl amount presents a relativell- lag? surface for evaporation. Since mercury shows meas~rable vo!-atility st a tempero.turc as lor^ 2s 8.5O F., mercury vapor will bo present in the atnosphere of anjr laboratory wbr.e mercury is exposed. promiscuously]

Jan 1, 1939

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936

By Wm. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville, Mont., is ore of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various miner of the United States. ACKNOWLEDGMENTS In the preparation of this paper the writer acknowledges the assistance of R. H. Willcomb, general manager, William Thorson, mine superintendent, and B. P. Bellport, mining engineer, of the Hughesville division of the St. Joseph Lead Co.; and of E. D. Gardner; supervising engineer, U. S. Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1931

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962