Search Documents

By G. F. Friel

A series of experiments in the U.S. Bureau of Mines Safety Research Coal Mine at the Pittsburgh Research Center evaluated the effects of crosscuts on the travel time of carbon monoxide (CO) along an entry to improve the accuracy of a mine-fire locator program. Three entries, ten single crosscuts, and three double crosscuts were instrumented with CO sensors. One-percent CO in nitrogen was released and monitored as it traveled the entries. In addition to dispersion of CO at the front of the CO wave, CO was entrained from the entry into the crosscuts. It was determined for an entry and single-crosscut configuration that the measured travel time for a concentration change of 5 ppm was 27% greater than the predicted time based upon entry volume only, but 13% less than the predicted time based upon entry and crosscut volumes. For an entry and double-crosscut configuration, the measured travel time for the same concentration change was 25% greater than the predicted time based upon entry volume only, but 10% less than the predicted time based upon entry and crosscut volumes. An effective dispersion coefficient for CO dispersion along one of the entries was estimated to be 1.5 m2/ s.

Jan 1, 2010

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By N. A. Tolch

[In this partner ?propulsive strength? or "strength" is defined as the relative propulsive effect of an explosive as determined by means of the United States Bureau of Mines ballistic pendulum. The data presented are derived from one particular strength testing device and do not necessarily represent the relative execution value of the different explosives in actual blasting. However, it is believed that the data obtained with the ballistic pendulum fire indicative of the relative propulsive or heaving force and are of value until propulsive strength can be expressed in more fundamental units.]

Jan 1, 1929

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By R. H. Nicholas

Shuttle cars have undeniably proved their worth as a means of transporting coal underground; however, several factors have arisen in connection with their possible improvement. This report .discusses the effect of shuttle cars that employ rough-tread and smooth-tread tires on mine roadbed, the amount of dust thrown into suspension by the use of such tire treads, and the service rendered by each type of tire. Involved, also, in this study are observations on the use of different amounts of calcium chloride on the haulageways.

Jan 1, 1949

By Paul H. Mutschler

The Bureau of Mines sponsored a study of the impact of changing technology on the demand for metallurgical coal and coke to 1985. Individual technologies were analyzed to determine what effect each had on the demand for and the consequent consumption of metallurgical coal and coke in the steel industry. The domestic steel industry demand for metallurgical coal and coke for the production of hot metal will probably increase through 1985. Formcoke if implemented on a worldwide basis could begin to supplant the U.S. export market for metallurgical coal. The major technologies that have contributed to the decline in demand for metallurgical coke per ton of hot metal are (1) the increased usage coupled with higher iron content of agglomerates, (2) modification of blast furnace practices such as high top pressures and blast temperatures, and (3) increases in the injection of supplemental fuels. The projected demand for metallurgical coal and coke under current technology for 1985 are 109.4 and 76.0 million tons, respectively. With future technology implemented, the demand for metallurgical coal and coke will be 82.0 and 56.9 million tons, respectively. The projected domestic demand for metallurgical coke could further decrease by as much as 15 to 20 million tons by 1985 if formcoking proves technologically and economically feasible.

Jan 1, 1975

By Geo S. Rice

"The most authoritative compilations on the coal resources of the British Isles are given in ""The Coal Resources of the World"" issued by the 12th International Geological Congress, 1913. The reserve, calculated to a depth of 6,000 feet, in seams containing not less than two feet of merchantable coal are as follows: Mining at present is conducted at depths from about 800 to 3500 feet. The shallower coals have largely been exhausted. The present average hoisting depth probably is about 1500 feet.The thickness of individual beds at present mined varies from about 2-1/2 feet up to 40 feet in thickness, the latter thickness being found in North Staffordshire. The coal is rarely found level, but is approximately level in some parts of Yorkshire. Anthracite is mined in limited quantities in Wales, and Wales also produces a very high grade semi-anthracite or smokeless coal, which is fa famous the world round, and is equaled only by the Pocahontas and New River coals in the United States:As concerns the methods of mining, these vary widely according to the pitch of the bed, the thickness of coal, and natural conditions, but the prevailing method is some form of longwall or semi-longwall, by which all the coal is extracted. The other principal method is a so-called pillar and, stall method, by which the coal is mined out, leaving square or rectangular pillars which are extracted on the retreat, making it virtually, a retreating longwall system. This method is applied where the roof is strong, and particularly in the thicker beds, as the longwall method is not so well adapted for mining where the thickness exceeds five or six feet, unless it is what is called a multiple seam, one in which there are partings of rock that provide material for building walls, which the roof in subsiding gradually squeezes down."

Jul 1, 1920

By R. R. Hornor

Due mainly to conditions brought about by the war , the metal mining industry in this country is now passing through one of the most critical stages in its history , and is confronted by new problems upon the solution and adjustment of which depends , in a large measure , its future welfare and prosperity . The chief factors contributing to the cost of production are the cost of labor and supplies . It is conceded by our leading mine operators , managers , and engineers that any material reduction in the cost of labor or supplies , within possibly the next two or three years , cannot be anticipated , anl it is not thought likely that pre - war prices will ever again prevail . This being true , the mine operator must look in some cther direction to effect economies that will lower production costs . If this cannot be accomplished it will mean , in many instances , that mines and metallurgical works will have to be closed and abandoned , which will tend to disorganize the entire industry . How to lower production costs and still maintain the present high standard of wage , is the problem that is engaging the serious attention of mine operators and managers over the entire country . In As a solution to this problem it is thought that the most promising field of investigation lies in the direction of systematizing and standardizing mining practice , so as to effect economies in the use of both labor and materials . other words , to eliminate , in so far as possible , unproductive effort and waste and thereby secure a maximum of productive results , It is not the idea to speed up work or to demand a greater effort on the part of the workman , but rather so to systematize and standardize the various under ground operations that his energy will be directed into more useful and productive channels ,

Dec 1, 1919

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By Stephen P. Holt, John A. Bowsher

A preliminary examination of the mica deposits in Culberson and Hudspeth Counties , Texas , was made in September 1942 by A. B. Needham, district engineer of the Bureau of Mines . The deposits were reexamined by R. C. Redfield , associate mining engineer of the Bureau in November 1942, at which time he was accompanied by Philip S. Hoyt , geologist , and J. C. Moore , foreman of the Texas Mica and Feldspar Company . Exploratory work was started on February 16 , 1944 , and terminated on April 30 , 1944. A crew of 4 to 10 men was employed under the supervision of the authors .

Feb 1, 1947

By Jack C. White

This U.S. Bureau of Mines report assesses the resource potential of trace metals present in commercial Ti mineral concentrates. Metals of greatest interest: are those defined as "strategic and critical" by the U.S. Congress in 1981. Metals of interest in Ti mineral concentrates are Cb, Cr, Ta, Th, U, V, and Zr. Commercially available Ti mineral concentrates were studied. Characterization and analysis of major and minor constituents were performed by X-ray diffraction, neutron activation, inductively coupled plasma emission, atomic absorption, and classical wet chemical techniques. Of the metals investigated, the Cb, Ta, and V content of some concentrates may be a significant potential resource, depending on their amenability to recovery.

Jan 1, 2010

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of the Sheep Creek West Wilderness Study Area (ID-111-36A), Owyhee County, ID, for the U.S. Bureau of Land Management. The Wilderness Study Area consists of 11,680 acres centered approximately 20 miles south of Grasmere, 10. It contains no mines, claims, or prospects. No mineral resources were identified; however, a geode occurrence within and adjacent to the Wilderness Study Area, and minor amounts of placer gold along Sheep Creek, may be of interest to rorkhounds and recreational gold panners.

Jan 1, 1986

By N. Greninger

The Bureau of Mines examined the possibility of a seasonal variation of respirable dust concentration in U.S. coal mines. The first step was to review company and MSHA-inspector dust samples that had been collected during the past several years in 14 selected mines for compliance purposes. Results indicated severe scatter in data; most standard deviations of the dust concentrations measured in winter and summer months were comparable in magnitude with the mean values of dust concentrations for the seasons. Therefore, a detailed statistical analysis was conducted. At the 90% confidence level, the company samples of three mines had winter means 0.15 to 0.54 mg/m3 higher than the summer means; six mines had negligible seasonal variations; and five mines had winter means that ranged from higher to lower than the summer means. Inspector data, however, were too sparse for analysis. In view of both the low frequency of occurrence of a seasonal effect and its wide scatter in several of the mines, the study was ended with the conclusion that seasonal varia-tion in respirable dust levels, in general, is an insignificant factor.

Jan 1, 1986

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

By P. M. Brown

The Bureau of Mines is investigating a dewatering technique for coal-clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong stable flocs that can be dewatered on a static screen. A field test unit (FTU) using this technique was operated at approximately 400 gal/min, using a waste stream from the flotation circuit of a coal preparation plant. Consolidated coal-clay material con-taining 55 to 60 pct solids was produced when the flotation circuit slurries of 2.7 to 8 pct solids were treated with 0.1 to 0.3 Ib PEO per ton of solids. The FTU was also operated at 64.5 and 87.5 gal/min using a portion of the underflow slurry from the preparation plant's thickener. Consolidated coal-clay material containing 55 to 60 pct solids was produced when the thickener underflow slurries of 19 to 24 pct solids were treated with 0.08 to 0.2 Ib PEO per ton of solids. PED-treated materials continued to dewater when placed in a pit.

Jan 1, 1983

Develop and evaluate a mechanical position and heading system (MPHS) that provides information about underground mining machine position and heading to aid in the remote positioning of mining machines during face maneuvers. Background While great improvements have been made in mineworker safety, progressive technology continues to create a safer, better working environment for miners by keeping them away from the dangerous face area. In maintaining such high standards of safety, the Bureau is investigating remote, computer-assisted operation of mining systems for underground, highwall, and surface mining applications. A key component of computer-assisted operation is a guidance system. Since there are no guidance systems on any commercial continuous mining machines, the Bureau itself developed and tested the mechanical position and heading system (MPHS). The MPHS is based on linear position transducers (LPT's), and operates on principles of triangulation to provide machine position (xy coordinate), and orientation in the xy plane (yaw or heading). These data are needed in order to keep the continuous mining machine in proper alignment before and during the cutting cycle. The MPHS theory development is in three parts: characterize the sensors used and their configuration; select and define the navigation reference frames; and derive a closed-form solution for determining the position and beading from sensor information. Application of the MPHS theory required the development of hardware, software, and system interfaces.

Jan 1, 1992

By L. C. IlsLey

"Nearly every piece of electrical equipment used in mines ""breathes."" In other words, motors, controllers, rheostats, switches, and other similar equipment, even though encased in seemingly tight compartments, breathe in the atmosphere that surrounds them.As the apparatus is used, the temperature of metallic parts is changed generally in positive direction through the heat by friction and the heat due to the electric current. When the apparatus is idle it gradually cools down to the temperature of the surrounding atmosphere.This increase of temperature during operation and return to normal temperature when operation stops alternately raises and lowers the temperature of the atmosphere within the compartments which, in strict accordance with Charles' law -will expand or contract in proportion to any given temperature change.As compartments are not gas-tight, such expansion and contraction will force the atmosphere out of the compartment =on expansion and suck the surround¬ing atmosphere into the compartment during contraction, hence the term ""breathing.""Investigators2 of explosion-proof equipment have recognized that such an interchange would take place and have designed their equipment to safeguard possible explosions within the compartments."

Jun 1, 1927

By L. C. IlsLey, H. B. Freeman

In connection with the approval of coal-cutting machines for service in gaseous mines , the engineers of the Bureau of Mines have been somewhat concerned as to the type of trailing cables that could safely be used on permissible outfits . While no final action has been taken on this question ( tentative approvals having been granted pending investigations ) , the Bureau has been endeavoring to collect data and information on this question which would permit a fair , yet safe , ruling to be made . For this purpose cooperative arrangements were made with three coal companies to visit certain of their mines , making inspections inside the mines to observe the cables and cutting machines in operation . In all , twenty mines were visited . A questionnaire covering the operations of trailing cables was filled out at each of these mines . In a few instances no personal inspection was made , the information being supplied by mine officials after conferences with the Bureau's engineer . At other mines the information given by mine officials was supplemented by personal observation inside the mines , usually at a time when the cutting machines were in operation .

Jul 1, 1923

By Peter L. Swanson

This investigation, which began 90 minutes after the February 3, 1995, seismic event, has benefitted from the assistance of a large number of individuals. These individuals provided information, data, analysis, brainstorming opportunities, field equipment, assistance with communication, conducted rock mechanics tests, and provided insight into mining in the southwestern Wyoming trona district. They include Rich Hodgson, Ron Hughes, Larry Refsdal. Mike Weller, John Kolesar, Joe Vendetti, and Rick Casey (Solvay Minerals), Dave Delling (Solvay consultant - former Solvay President), Karl Zipf (formerly with USBM, now with MSHA), Bob Friend, Bob Ferriter, Dave Ropchan, Jerry Davidson (MSHA Tech Support), Don Stauffenberg, Ben Hohler (Wyoming State Mine Inspector's office), Bruce Presgrave (USGS/NEIC), Chris Wood, Dan O'Connell (Bureau of Reclamation), Sue Nava, Jim Pechmann (University of Utah), John Norgord and members of FMC's mine rescue team (FMC Corp.), Bill Walter (Lawrence Livermore National Laboratory), Ron Gerlick, Kevin Wood, and Mike Harmel (USBM rock mechanics lab), Jim Case (Wyoming State Geological Survey), and Solvay consultants. In addition, many individuals helped us gather information on other recent large mining-related seismic events in Germany, Russia, and Australia. and other parts of the United States. These individuals include Wolfgang Minkley (IfG Institut fur Gebirgsmechanik, Leipzig), Arnfinn Prugger (Potash Corp. of Saskatchewan), Hartmut Spetzler (University of Colorado/ University of Bayreuth), Sergei Stanchits (Ioffe Poly-technical Institute, St. Petersburg), Rocky Thompson (Cyprus-Amax) and numerous seismologists throughout the Internet.

Jan 1, 2011