Search Documents

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By Patricia R. Devine

This report expands an earlier study by Jack Faucett Associates (OFR #40-88) of the same title. Both reports are based upon an interindustry analysis from 1963 through 1982, during which time U.S. metals consumption and production did not keep pace with economic growth. The report discusses three sources of change: technological change, economic growth, and composition of final demand, as well as the relative importance of the individual components of final demand for metals. The results show investment and personal consumption to be the most metal-intensive components of final demand, and technological change to be the major cause of decline in consumption growth during the study period. Technology change is defined as alterations in production processes resulting in more or less consumption of metal per unit of output, often because of material substitutions and design changes. A trade analysis shows the significance of import growth, particularly indirect imports (metal contained in imported goods) as a factor contributing to the reduced growth rate of domestic metal production. The effect of import growth is partially offset by indirect export growth, suggesting that continued increase of all U.S. exports can have a strong effect in reducing the negative trade balance in metals.

Jan 1, 1988

By Charles L. Harness, A. T. Coons

Sodium carbonate, Na2CO3, more commonly known as soda ash, is the most important of the alkalies. Sulfuric acid is the only heavy chemical, Soda ash enters the market either as the natural product or as a manufactured derivative of common salt. Notwithstanding their common occurrence in closed basins of the Western States, natural sodas are produced at present by only four firms, all in the same California area, and satisfy only 4 percent of domestic demand for soda ash; soda ash made from salt supplies 96 percent of the requirements. The impossibility in wartime of routing all westbound American shipping through the Panama Cami.l has curtailed Pacific Coast receipts of soda ash and-increased the importance of local resources of natural carbonates. One of the most promising of ·these is the recently discovered trona (sodium sesquicarbonate)· deposit 2o·mnes· west of Green River, Wyo. Reserves are likely to run into hundreds ·of million·s of tons, and the deposit probably could be worked by the room-and~pillar· system of mining, like common salt or coal. • • Raw materials ·ne·cessary for manufacturing synthetic soda ash occur closely associated in m·afiy parts· bf the United 8tates. Almost unlimited resources of salt in brines and in rock-salt depbsits are located near limestone quarries in many areas. The· limesto'ne furnishes the carbon dioxide for the manufacture of soda ash arid the lime f o'r the recovery of ammonia. used in one step of the process. Expansion of the industry to meet wartime needs depends chiefly on availability of trained labor, materials, and equipment necessary for the erection of additional units.

Jun 1, 1942

By Robert K. Koch

The reactions of alumina and alumina monohydrate with wet hydrogen fluoride gas were studied by the Federal Bureau of Mines to determine the feasibility of producing commercial-grade aluminum fluoride from offgases generated by pyrohydrolysis of siliceous fluorspars. The test results showed than an aluminum fluoride reactor operating at maximum efficiency could retain 96 percent of the fluorine contained in off-gases generated by pyrohydrolysis of siliceous fluorspar. The requirements are a reactor temperature of 200° C. and a reactor entrance gas containing 5 mole-percent hydrogen fluoride. Partial pressure equilibrium constants were determined for the reaction of alumina monohydrate and wet hydrogen fluoride gas from 200° to 350° C. and for the reaction of alumina and wet hydrogen fluoride gas from 350° to 700° C. Both reactions are reversible, and they proceed in directions that are dependent upon the temperature and the relative HF:H2O concentration. Logarithms of the equilibrium constants were used to plot the reaction isobars; these can be used to calculate the theoretical maximum efficiency of a reactor processing wet hydrogen fluoride gas between 200° and 700° C. The theoretical maximum efficiency decreases with increasing temperature.

Jan 1, 1961

By F. E. Joyce, Charles Prasky

This report describes the response to high- temperature sulfatization of a variety of manganese minerals and companion compounds which may occur either as a principal component or as a gangue material in low- grade manganese deposits . Fourteen manganese samples representing oxide , carbonate , and silicate minerals as well as seven compounds which might occur as gangue with manganese minerals were tested batchwise in a bench- scale apparatus under conditions which would be favorable for the sulfatization of manganese . The manganese minerals substantiated thermodynamic predictions and responded to sulfatization but to varying degrees . The gangue materials , MgO , MgCO,, CaO , and CaCO3 , were sulfatized readily in contrast to the iron oxides and the aluminacontaining material which were not .

Jan 1, 1964

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By Elio Ferreira

This report describes the design, and development work performed to reduce the volume and weight of the miners caplamp battery, as well as a headpiece with a swivel mechanism containing a halogen bulb with two filaments. Work was also conducted in the development of a maintenance free battery. The design concept is based on non-sintered Ni-Cd technology, with an energy density of 22 Wh/lb. The cap lamp system developed has been approved by the Mine Safety and Health Administration (MSHA) and can be manufactured for mine use.

Jan 1, 1988

By Arne Landsberg

Experiments were made with a batch reactor to determine the effect of gas pressures, temperature, and gamma radiation intensity on the reaction CO + Ch ? COC12. The equation, [dp = 0.0110 (1 - 0.01t) (PCOI)1/2 PC12] where [dP] is the change of pressure of phosgene with time (atm/hr), t is the temperature (°C), PCO and PC12 are the reactant pressures (atm), and I is the radiation intensity (r/hr), was found to best fit the data. Oxygen and a large ratio of reactor surface to volume retarded the reaction, but inert gases had no effect. A low-temperature reactor system is proposed to take advantage of the conditions which give a high reaction rate with gamma radiation and a simple scheme of product purification.

Jan 1, 1970

By M. M. Wong

Electrolysis of titanium carbide and a material consisting of titanium, carbon, nitrogen, and oxygen as soluble anodes in Used electrolytes was investigated by the Bureau of Mines for the preparation of crude titanium metal. Tests made in all-chloride electrolytes showed only a low recovery of titanium as well as a substantial volatilization of titanium trichloride (TiC13) when present in the electrolyte. Electrolysis at 750° to 850° C in a mixture containing 85 percent NaC1-15 percent potassium floutitanate (K2TiF6) yielded as high as 91 percent recovery of titanium from titanium carbide and 62 percent recovery of titanium from the titanium-carbon-nitrogen-oxygen material. Problems associated with the preparation of crude metal by fused-salt electrolysis are discussed. The crude metals produced from both anode materials were electrorefined in a sodium chloride-titanium chloride (NaCl-TiC12) electrolyte, and ductile titanium metal was obtained.

Jan 1, 1963

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

By P. C. McWilliams

The Bureau of Mines investigated ground support problems in four major block-cave mines to assess the current "state-of-the-art" and to delineate areas for future research. The most significant problem is the inability of present support systems to hold moving ground. Further, as mining progresses to greater depth, this problem becomes more serious. Providing adequate temporary support capable of withstanding primary and secondary blasting is the next most significant problem. A detailed analysis of the effect of mining methods on support problems is also recommended for future research.

Jan 1, 1975

By Carl Rampacek

The conversion of dilute sulfur dioxide gas into sulfuric acid by autoxidation in mechanical cells of the flotation or gas absorber types was investigated. Bench-scale tests were made with sulfur dioxide-air mixtures to determine the influence of several factors on autoxidation of sulfur dioxide, using iron and manganese salts as catalysts. The laboratory investigation subsequently was extended to pilot plant acid-making tests, using a modified turbomixer gas absorber having a 12-inch-diameter impeller. Sulfur dioxide gas was produced for the tests by roasting pyrite in a fluidized-bed reactor. In the better tests, made with manganese sulfate as the catalyst, the equivalent of 1,000 pounds of anhydrous H2SO4 was produced per 24 hours as a 10-percent solution; power consumption was 0.2 kwhr per pound of equivalent anhydrous acid synthesized. The batch and continuous tests demonstrated the technical feasibility of producing dilute sulfuric acid by autoxidation of sulfur dioxide gas in mechanical cells when converting pyrite roaster or waste smelter gases.

Jan 1, 1963

The Bureau of Mines conducted a field study of respirable dust concentrations at an underground room-and-pillar oil shale mine and at the aboveground milling facility to determine the dust generation sources, personal respirable exposure, characteristic minerals, and size distribution of the dust. Major dust sources in the mine were the scaling and blasthole drilling operations, and major dust sources in the processing mill were the screening and crushing operations. Principal minerals found in the airborne respirable dust were albite, analcite, calcite, dolomite, quartz, and orthoclase. The average alpha-quartz content of mine and mill respirable dust samples was 4.1 pct and 15.5 pct, respectively. Carbonaceous material such as diesel particulate accounted for approximately 75 pct of the respirable particulate found in the mine. The average coefficient of variance of respirable dust concentrations measured with approved personal dust samplers in the mine and mill was 7.6 pct, the best precision observed to date with the personal dust sampler operated in the field.

Jan 1, 1977

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By T. Kessler

As part of a respirable mine-dust research program at the U.S. Bureau of Mines, spark-source mass spectrometry has been used for the semiquantitative determination of trace elements (200 ppm weight or less) in raw coals. In addition, several minor and major elements have been determined using this technique. Sixty-four elements ranging in concentration from 0.01 to 41,000 ppm weight were determined in one anthracite, two mvb, four lvb, and six hvab raw coal samples. The samples represented 10 coal seams located in Pennsylvania, West Virginia, Virginia, Utah, and Colorado.

Jan 1, 1973

By Harry R. Nicholls

A simple economical method has been developed for determining the in situ longitudinal and shear velocities in rock from which its elastic constants can be calculated. By detonating small charges of high explosives in shallow drill holes near a free surface, both longitudinal and shear waves were generated simultaneously. Accelerometers and velocity gages mounted to the rock surface were used to record the arrival time for both waves over travel path lengths from 50 to 450 feet, Measurements were made in two rock types. From the arrival time measurements, the longitudinal and shear wave velocities were calculated. From these velocities and the density of the rock, the elastic constants were calculated. The dynamic elastic constants of drill core samples of the two rock types were determined in the laboratory by the resonant-frequency method, The lab- oratory and in situ elastic constants are compared and significant differences noted. In general, there is less spread in the in situ data than in the laboratory data, and Poisson's ratio does not fall outside the theoretical limits for the in situ data as is often the case for laboratory-determined elastic constants.

Jan 1, 1961

By Bertrand L. Johnson

Langbeinite, a comparatively rare mineral that has been reported from only five countries in the entire world, has recently attained considerable economic importance in the United States and Poland. Since September 1940, several hundred thousand tons have been produced in one of the Carlsbad (N. Mex.), potash mines for chemical and fertilizer use. As it is a newcomer in this field, and as it is the source of fertilizers possessing special advantages, notably for soils deficient in magnesium or requiring sulfate fertilizers, a discussion of its properties, occurrences, uses, mining, and treatment is appropriate at this

Jan 1, 1944

By I. L. Feld

This Bureau of Mines report describes the development of a simple method of producing low-phosphorus hematite concentrates from certain submarginal southeastern iron ores. The investigation was undertaken to obtain additional information on the Clinton iron ore outcrops at the southwestern extremity of the Birmingham district of Alabama and to assist in the development of operating techniques that would make it profitable to use the marginal ores of this area for blast-furnace feed. Batch and continuous pilot-plant tests demonstrated that a relatively simple wet scrubbing treatment) followed by a desliming operation to reject argillaceous (clayey) gangue, consistently yielded a marketable granular hematite product. Iron losses were relatively high but could be tolerated in view of the low treatment cost.

Jan 1, 1960

By James S. Browning

Research by the Bureau of Mines demonstrated that organic heavy liquid adhering to or adsorbed on fine mineral particles can be effectively removed by a novel method embracing pulping or displacement washing with hot water alone or in combination with a detergent. Displacement washing with steam alone or in combination with a detergent also was effective for removing the heavy liquid. In tests of sized minus 48-plus 200-mesh mineral charges, both the hot water washing with detergents and detergent steaming effectively reduced the heavy liquid losses on the particles to about 0.2 pound per ton of mineral or less. Centrifuging of the wash solutions permitted an almost complete recovery of heavy liquid from the solution as a pure heavy liquid product.

Jan 1, 1966

By A. B. Cecala

The Bureau of Mines has developed a pallet loading dust control system designed to lower the dust exposure of workers during the bag stacking process at mineral processing facilities. The system makes bag stacking much easier because the pallet height remains constant throughout the entire bag stacking cycle through the use of a hydraulic lift table. The system uses a push-pull ventilation technique to capture the dust generated during bag stacking. A low-volume, high-velocity blower system operating at approximately 150 cfm blows a stream of air over the top layer of bags on the pallet. The blower system is composed of two 3-in air jets (approximately 1,200-ftjmin velocity) directed toward an exhaust system on the opposite side of the pallet. As these air jets travel across the pallet, they entrain the dust generated during bag stacking. The exhaust ventilation system pulls approximately 2,500 cfm of air and dust through the exhaust hood. This exhaust air can then be dumped into a baghouse ventilation system, or filtered before being discharged outside the mill. During a laboratory evaluation, a 70-pct dust reduction was recorded for the bag stacker. The system was then evaluated in an actual working environment. The first field evaluation was performed at a silica sand operation in which one worker performed the entire loading and bag stacking process. This worker's dust exposure was lowered 76 pet when using the new pallet loading system. The second field evaluation showed only moderate dust reduction, but this was mainly attributed to an overriding problem associated with background dust and the cleanliness of the bags. From both the ergonomic and production standpoint, the system was well received by both the workforce and plant management.

Jan 1, 1988