Search Documents

By Mark S. Sanders

Based on laboratory tests and preliminary field tests of off-the-shelf steel toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners' boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A five month field evaluation compared the prototype boots to the boots the participants usually wear. Although objective slip and fall data showed no significant advantage for the prototype, subjective evaluations made by the participants indicated increased traction for the prototype boots. Approximately 75 percent preferred the prototype to their own boot. Approximately one-third used the lace-up capability. It was concluded that molded soles provide better traction than calendared soles for the underground mining environment.

Jan 1, 1982

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By F. S. Crawford

Companies which have been engaged in safety work for a number of years are becoming increasingly aware of the fact that it is not enough to supply guards for various pieces of machinery and equipment and to supply safety inspection to see that rules are being carried out. Studies of many safety organizations have demonstrated that the accidents which could have been prevented by proper guards constitute only a small percentage of the total acci- dents, and amount to perhaps not more than 15 per cent. Evidently, if success is to be attained in preventing all accidents which it is humanly possible to prevent, a company must have the cooperation of every employee. Mining particularly presents probably the greatest hazards of any industry. Prevention of accidents. is made increasingly difficult because men often work alone, although generally in pairs, and only in the concentrated systems of mining do they usually work in groups of more than three or four. Supervision is difficult, therefore, and much reliance must be placed upon the individual workmen. In mining, as perhaps in no other occupation, it is of the greatest importance that individual workmen should receive continuous safety education. Within the last few years safety education has come to the front as one of the most important of accident-prevention measures, although it is true that its importance has been repeatedly stressed by the United States Bureau of Mines and other national safety organizations since the inception of the safety movement many years ago. A review of the safety educational methods of some companies in the Lake Superior district should be of interest. Perhaps better methods are in use in other parts of the country, but the methods shown have been instrumental in many cases in reducing the number of accidents. In one mine in the district whose methods are described the frequency of accidents has been reduced to zero within the last two years. A number of other mines in the district have recently gone into the class having no lost-time accidents for considerable periods of time. One company in the Lake Superior region, operating over 30 mines, succeeded during one month of 1930 in operating every mine without having a single accident which caused lost time beyond the day of the injury. Records like these are increasing in number, and while it is believed that they are the combined result of different means of safety activity, it is undoubtedly true that many of these results were obtained through safety educational methods.

Sep 1, 1931

By John J. Sammarco

This U.S. Bureau of Mines report describes the research effort and results for a computer-assisted appendage control system of a Joy 14CM continuous mining machine. The cutter head (shear), gathering head, conveyor, and stabilizer jack are the appendages. Positional control of each appendage is accomplished by specifying the desired position to the appendage control computer, which uses appendage position sensor data. Appendage movement is actuated until the desired position is attained as determined by control algorithms. A description of the sensors, mechanical and electrical interfaces, data acquisition and control (DAC) system, experimental method to determine appendage response characteristics (range of motion, start and stop delay times, and movement rates), and their application to the position control loop algorithms are presented. Also, the test results for the shear in an unloaded (free space) and loaded (cutting) condition of the shear are presented.

Jan 1, 1991

By D. Harrington

While apparently the hysteria with regard to silicosis and other occupational diseases has largely subsided and this subject is being more carefully considered and soberly judged, it would be poor policy for any employer to maintain that the storm has ended and that he can relax and revert to conditions as they were 5, 10, or more years ago. The fact is that the plan of paying occupational-disease compensation is now in its infancy and can be expected to grow rapidly. At present, while all of the States of the Union, including the District of Columbia and excepting only Arkansas and Mississippi, have compensation acts, only the following make provision for occupational diseases to some extent or in one way or another: California, Delaware, Connecticut, District of Columbia? Illinois, Indiana, Kentucky, Massachusetts, Michigan, Minnesota, Missouri, Nebraska, New Jersey, New York, North Carolina, North Dakota, Ohio, Pennsylvania, Rhode Island, Washington, West Virginia, and Wisconsin. Silicosis is compensable in one way or another in California, Connecticut, District of Columbia, Illinois, Kentucky, Massachusetts, Missouri, New York, North Carolina, North Dakota, Ohio, Pennsylvania, West Virginia, and Wisconsin, and possibly in other States. During the past few months, occupational-disease legislation (largely silicosis) has been considered in some form in Arkansas, California, Delaware, Idaho, Maryland, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah and Washington. It will be surprising if comparatively comprehensive occupational-disease legislation is not on the statute books of nearly every State in the Union within the next 5 years. With this situation confronting him, the farsighted industrialist who has the interest of his organization at heart, if he has not already done so will immediately start to "put his house in order" by studying possible occupational disease hazards to his employees and promptly applying known remedial measures or attempting to devise such measures if none exist. Unquestionably, one of the most important of the surveys to be made relates to dust occurrence, as State laws on occupational disease are almost certain to contain provisions, on silicosis and, with almost equal certainty, the provisions of any State law are not likely to be particularly similar to those of other States.

Jan 1, 1938

By Oliver Q. Leone

The effect of oxygen content in the anode metal on titanium electrorefining characteristics was studied. Increasing quantities of oxygen in the anode resulted in increased anode scale formation, decreased anode and cathode current efficiencies, lower titanium recovery efficiencies, and higher oxygen content of the cathode products. The titanium electrorefining process performed best when the anodes did not contain more than 0.5 percent oxygen, although anode dissolution was recorded for alloys containing up to 25 percent oxygen. Back emf affords a useful index of an alloy to electrorefining.

Jan 1, 1965

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By John E. Pahlman

An increasing number of gold and silver mining operations are employing cyanide solutions to effectively dissolve silver and gold from finely disseminated ores. Many of these operations use small, packaged processing systems like the State of Maine filter system, which employs zinc precipitation of gold and silver. Solution-clarifying filters in these systems become blinded with calcium carbonate (CaC03) scale and require frequent (every 2 to 10 days) dismantling of the filter units for acid cleaning, This is a hazardous operation as it is not compatible with the alkaline cyanide leach solutions and may result in the evolution of toxic hydrogen cyanide (HCN) gas during cleaning and during any accidental acid spill. The Bureau of Nines has investigated an alternative, nonacidic method of cleaning blinded State of Maine filters that employs ethylene- diamine-tetraacetic-acid (EDTA) type chelating agents to dissolve the scale. In situ cleaning of a 150-st/d State of Maine filters with EDTA- type chelating agents was successfully demonstrated. Greater than 90 pct of the CaC03 scale was removed in about 10 min with circulation of 31 L of 2.5-pct-EDTA solution through the filter unit. The EDTA cleaning method not only eliminates the cyanide hazard in filter cleaning but is advantageous from the standpoint of operating costs and productivity.

Jan 1, 1986

By Irving Hartmann, Bernard Lewis, John Nagy, H. P. Greenwald, H. C. Howarth

"ORIGIN OF INVESTIGATIONThe Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States, July 24J 1946, contains the following provisions with regard to rock dusting: Article VI. - Section 2. Rock dusting.(a) All mines, except those mines or those locations in a mine which are too wet or too high in incombustible content to propagate an explosion, shall be rock-dusted to within 80 feet of the faces of rooms and entries; however, if the mine or any part of it is wet but becomes dry, the mine or portion of the mine so affected shall be rock-dusted as ·soon as it becomes dry. (b) In mines partially rock-dusted or in mines that are required to start rock dusting, haulageways and parallel entries connected thereto by open crosscuts shall be rock-dusted. Back entries shall be rock-dusted for at least 1,000 feet outby the junction with the first active entry. Inby this junction, the rooms, entries, and crosscuts shall be rock-dusted by generalized rock dusting as provided for in section 2(a).(c) Where rock dust is applied, it shall be distributed upon the top, floor, and sides of all open places and maintained in such quantity that the incombustible content of the mine dust will not be less than 65 percent. In trackless entries and air courses, protection in lieu of generalized rock dusting may be had by using bags filled with rock dust, if they are placed at regular intervals and staggered as described in Bureau of Mines Report of Investigations 3411."

Feb 1, 1948

By J. E. Gebhardt

External control of the electrochemical potential of a bed of mineral particles has been investigated by the Bureau of Mines as a method for controlling particle inter-action with organic collectors and thus, flotation response. A cylindrically shaped, 200-to 300-g bed of sulfide mineral particles was used as the working electrode to examine the potential distribution in the bed. The dissolved oxygen concentration of the electrolyte had a significant effect on the potential profile across the mineral bed. Low oxygen levels were necessary to achieve uniform electrochemical potential distributions. Flotation separation of a chalcocite-pyrite mineral mixture by controlled potential was achieved using ethylxanthate, but the flotation behavior of chalcocite and pyrite from the mixture does not follow the flotation behavior of the individual minerals. That is, the presence of another sulfide mineral alters the flotation behavior with ethylxan-thate. Galvanic interaction due to mineral-to-mineral contact between chalcocite and pyrite contributes to differences in the recovery. Chalcocite dissolution products had a deleterious effect on pyrite flotation by activating flotation below -0.1 V (saturated calomel electrode) and depressing flotation above -0.1 V. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1985

By G. J. Slavens

The Bureau of Mines has devised technology to recover cobalt, nickel, and byproduct copper from domestic lateritic material using an oxidative, ammoniacal ammonium sulfate leach. Nickel, cobalt, and copper were recovered by solvent extraction and electrowinning. To reduce the cost and complexity of cobalt recovery, an alternate method using lig-nite to extract Co3+ was investigated as reported herein. In the first 25 BV (bed volumes) of solution contacted with lignite, 97 wt pct of the Co3+ was extracted in & downflow column at pH 9.3. After 85 BV, the lignite was loaded to 1.5 wt pct Co3+ and further ex-traction was minimal. The lignite extracted cobaltic ammine complexes rather than cobalt ions and was nonselective as to other -metal cations and ammonium ions. Deleterious cations and 80 wt pct of the nonammine ammonium ions were removed prior to acid elution of the lignite. The removal of the ammines prior to elution to produce an ammonium-ion-freeCo3+ eluate was only partially successful. Thus Co3+ removal from ammoniacal solutions by lignite is technically difficult and economically unfeasible. It was also determined that reduction of Co3+ to Co2+ occurred during the extraction-elution process.

Jan 1, 1984

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By Harry R. Johnson

Laboratory experiments were conducted to study the carbon deposition characteristics of a high-gravity, paraffin-base crude oil. The results of these experiments indicate that a fuel supply adequate to initiate a combustion wave can be deposited in high-gravity-oil reservoirs. These results are significant because there has been considerable doubt whether oils over 35° API gravity are able to deposit sufficient fuel. Considered in these studies were the effects of air flux, temperature, initial oil saturation, and time on carbon deposition. Conditions that maximized carbon deposition in the laboratory and an understanding of the nature of carbon formation are shown by graphical interpretation of the data. Statistical techniques were used to design and analyze the results of the retort tests. For the same amount of laboratory work, this approach yields more information about the systems that were studied than the classical method of research presently used in many laboratories. In addition, the accuracy of calculating the effect of each variable on carbon deposition is twice that of the classical approach. This paper develops the statistical approach to research without complex mathematics, thus enabling the reader to grasp the concept of how statistics can be applied to study many complicated problems.

Jan 1, 1966

By S. H. Lorain

This paper is one of a series on mining and milling method and costs being published by the United States Bureau of Mines. The Golden Messenger mine, operated by the United Gold Mines Corporation, is in the York-Confederate Gulch mining region in Luis and Clark County, Mont., 22 miles northeast of the city limits of Helena and about 1 mile north of the town of York. It is the first operation to exploit successfully the low-grade ores of the York-Confederate Gulch area. The unusual vein structure presents some mining problems that have been solved in ail interesting manner.

Jan 1, 1937

By John C. Gagliardi

The size and complexity of modern surface haulage trucks has resulted in an increased reliance upon sensors and electronic-based instrumentation for safe and efficient operation. Design engineers need accurate information about the equipment vibration environment to efficiently and effectively build components for installation on mobile mining equipment capable of withstanding the mine environment. Examples of such components include backup alarms, communication equipment, microprocessor-based controllers, and a wide variety of sensors. Unfortunately, this information is not available to the majority of both original equipment and aftermarket equipment manufacturers. To address this problem, the U.S. Bureau of Mines performed field vibration measurements on a variety of surface mining haulage trucks. The vibration measurements were then analyzed and test specifications were developed in the form of envelopes. In conjunction with test specifications, recommendations to aid manufacturers in implementing a vibration environment test program have been included with an illustrative example.

Jan 1, 2010

By H. Kenworthy

[Experimental studies were made to develop a laboratory technique for direct removal of cadmium and germanium from sphalerite concentrates. Cadmium- and germanium-bearing concentrates from the Illinois-Kentucky fluorspar field were sound to be, amenable to an inert atmosphere fuming process for removing these two moats in the form of gaseous sulfides. Treating the condensed fume by pyrometallurgical methods upgraded the material end provided a means of partly separating the constituents. Cadmium was concentrated about 35:1 arid germanium about 300:1. The extractive investigations were supplemented by vapor-pressure studies on the sulfides of germanium to obtain fundamental data for larger scale laboratory conditioning and control when treating the zinc concentrates. Vapor-pressure curves were developed for synthesized monosulfide and disulfide The results of these- investigations indicate the possibility of significantly increasing the recovery of cadmium from zinc concentrates. Comparison with present recovery of germanium cannot be made, since commercial recovery data arc not available.]

Jan 1, 1956

By D. Harrington

In this period of generally increasing taxes of various kinds, one hears less complaint by mining companies about the high cost of workmen's accident compensation than was the case a few years ago, the reason perhaps being that other and more pressing phases of the tax problem now over shadow the heavy expenditures for compensation premiums which a few years ago were considered a severe burden on the mining industry. Nevertheless, the financial expenditures of the mining industry in higher compensation benefits and hospitalization or in higher premium rates, or both, instead of being less have actually increased in many States in the past year. In the spring of 1937, proposals for increased benefits to injured employees in compensation, hospitalization, or medical aid were actively before legislatures in California, Connecticut, Georgia, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Massachusetts, Michigan, Minnesota, New Mexico, Oregon, Pennsylvania, South Carolina, Texas, Utah, Washington, Wyoming, and possibly other States. In some cases, the proposed increases in benefits were so much greater than expenditures for similar items in the past that premium rates per $100 of payroll would almost certainly rise sharply. At this same time, occupational-disease-compensation coverage also was under consideration by legislatures in Arkansas, California, Delaware, Idaho, Indiana, Kansas, Massachusetts, Michigan, Minnesota, Montana, Nebraska, New Jersey, Ohio, Pennsylvania, Tennessee, Utah, and Washington. Sooner or later (and probably within the next few years) occupational-disease compensation will be accorded practically as wide recognition as accident compensation receives at present, and, unquestionably, mining in all of its branches will be affected more or less drastically. Hence, the present outlook is that the mining industry, in company with practically all other industrial activities, will be confronted by materially higher compensation costs than those of the past or the present, to which rather violent exception has been taken, at least in some States and at some times.

Jan 1, 1938