Search Documents

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By R. H. King

A very simple cold-bend test was devised and tested for evaluating thermoplastic jackets used on mine-power-feeder cables. A test sample is bent into a semi-circle whose radius is equal to the minimum bend radius recommended by IPCEA and then cooled to the, desired test temperature (-35°C). While at temperature, the sample is straightened by pulling the cable ends with a winch arrangement. The results show that of the jackets tested, those which cannot withstand the test literally burst when the sample is straightened.

Jan 1, 1978

By H. E. Powell

The smelting of brass and bronze generates a dust composed primarily of zinc oxide, with lesser amounts of other metal oxides, such as copper, lead, and tin. The small quantity of this waste generated by individual smelters and the relatively low unit value of the contained metals, suggests the desirability of reclaiming the metals onsite or at some nearby point. The Bureau of Mines has developed a process that fits these requirements. The technique consists of (1) dissolving zinc and copper from the dust with sulfuric acid, (2) recovery of copper by cementation, (3) recovery of zinc as zinc sulfate crystals, and (4) recovery of lead and tin as a salable residue. Alternatively, zinc may be recovered by electrodeposition. Free acid is recycled and no major pollution problems are generated by the process.

Jan 1, 1972

By Phillip W. Holland

The U.S. Bureau of Mines has developed a mass spectrometer method for determining helium in the parts-per-million to 10% range to an accuracy of ± 1%. The method employs a mass spectrometer, an inlet system utilizing a chromatographic gas-sampling valve, and an activated coconut charcoal trap cooled with liquid nitrogen. Gravimetrically prepared standards of helium in nitrogen were used to demonstrate the linearity of the method over the concentration range of 10 ppm to 10.66% helium.

Jan 1, 2010

By Alla D. Mah

Combustion energies of barium and strontium were measured by means of the combustion bomb calorimeter. The heats of formation obtained for the oxides were ?H298.15 = -139,060 ± 700 cal/mole of barium oxide (BaO) and ?H298.15 = -144,440 ± 400 cal/mole of strontium oxide (SrO). Tables containing heats and free energies of formation from 298.15° to 2,000° K were prepared.

Jan 1, 1963

By J. O. Lewis

"The significant facts in the problem of the relation between the production of crude petroleum, and the ever-increasing demand for petroleum products are that in spite of continually increasing production, improvements in methods of refining and utilization, and heavy increases in imports, demands grow still more rapidly and we seem always faced with a shortage at hand or lust ahead. On the other hand, our foremost authorities warn um of entirely inadequate domestic reserves. Looking abroad we find some large fields and many of speculative promise, 'tut the situation is complicated by international relations and demands by other countries which promise to be even more insistent than oars. This is the situation, then. We can not rely upon our own Crude Petroleum to meet the Ever Increasing Demand for Petroleum Products.I wish to follow this somewhat alarming statement by saying at once that the Bureau of Mines is not pessimistic in facing this situation. To my mind those who discuss the oil situation may be placed in three categories; the pessimists, the optimists, and the super-optimists. The pessimists I call those who see darkly and will concede no possibility of solution. According to them a few years will see the automobiles piled in windrows of 'dilapidated junk, I have no sympathy with this point of view and deem it vicious and entirely unwarranted.The optimists I term those who believe that there is a solution and that we shall be able to meet all of our reasonable requirements for as far into the future as can be foreseen, yet who recognizes that this desired end can not be attained without prevision and energetic effort.The super-optimists are those who will say to you, ""There is nothing to this talk of shortage, whenever we have needed oil we have always found it and always will."" To these gentlemen the possibility of an inadequate supply of oil is as incomprehensible as the possibility of the extinction of the passenger pigeon was to the early settlers who saw flocks that hid the sun for days during their passage. The passenger pigeon disappeared within two generations thereafter, and I deem this point of view as being perhaps more vicious than that of the extreme pessimist. It seems to me it is nothing less than improvidence lulling us into a false sense of security. There is an old proverb to the effect that ""The Lord helps him who helps himself."" I believe that we shall solve the oil problem, but I do not think it will be solved by vague optimism. It is going to call for our most energetic efforts and I believe we shall have to do a lot of ""helping ourselves."""

Oct 1, 1920

This volume summarizes the contract work performed over a nine-month period by Westinghouse Electric Corporation on a Cost Plus Fixed Fee Contract for the Department of Interior's Bureau of Mines. The contract has been extended primarily to carry out improvements recommended for equipment produced under the contract for communicating with and locating trapped miners. These improvements will enhance the performance and utility of this equipment for operational use in actual mine emergencies. An additional complete set of the equipment will also he furnished to the Bureau under this extension. The work of the basic contract was to design, produce and test hardware in accordance with the Westinghouse response to a Bureau of Mines Request for Proposal which was based technically on recommendations of a study performed for the Bureau by the National Academy of Engineering (NAE). The NAE study made suggestions for new equipment in three areas of need:

Jan 1, 1971

By William K. Tolley

The U.S. Bureau of Mines (USBM) is currently investigating the electrochemistry of mineral flotation. A significant need in this area is greater reliability of sensors. The USBM is testing electrolytic methods to clean and condition redox-sensing electrodes to improve the reliability and extend the service life of these instruments in the harsh physical and chemical environment of mineral processing slurries. A novel method for removing scale from fouled electrodes has been developed that includes anodic polarization to 1.2 V versus the Ag/ AgC1 reference potential, followed by brief potentiodynamic conditioning. Laboratory results show that this technique removes calcarious deposits from gold sensing electrodes and returns the electrodes to useful service within approximately 10 min. Mechanical abrasion to remove the scale is thereby avoided.

Jan 1, 2010

By John W. Finch

The present epoch in human history has been variously described as the age of coal, of oil, of iron and steel, and of power. All agree, however, that it is a great industrial period. Power is of course the vital force in the industrial organism; but power is derived chiefly from mineral fuels or from harnessed and controlled water - also a mineral substance although usually not so classified by industry. However, the latent energy of fuels cannot work for men until it is changed to active energy by combustion and until this active energy is converted into motion. This motion is just as indispensible as the energy itself. Likewise, the latent energy of water cannot be utilized until it, too, is converted into motion; out the mechanisms and devices for converting latent energy into motion, as well as the structures in which they are operated, would not be possible without metals and other minerals. Consequently, minerals are fundamental in industrial civilization.

Jan 1, 1938

By F. W. Brown

In 1942 the Explosives Division investigated electrostatic hazards associated with the manufacture, storage, and use of explosives. A report was issued in 19454/ presenting the data on the spark sensitivities of explosives. In 1948, the apparatus was redesigned and rebuilt to make the routine testing of explosives safer and more convenient. The rebuilt apparatus is described in this re-issue of the former report. Included are details of construction and a list of parts. PRINCIPLES OF METHOD In normal procedures without special precautions, it is possible for static charges to be accumulated on individuals or on ungrounded equipment or structures.5/ Static charges may be produced in many ways, but they are most commonly produced by rubbing or successive contact and separation of unlike surfaces, at least one of which is usually an insulator.

Jan 1, 1953

By A. W. Ambrose

"Those having an intimate knowledge of the relation between production and consumption of crude oil in the United States have realized for some time that production will not be able to keep pace with consumption. The American public has had this called forcibly to its attention by the increased prices of gasoline and crude oil, and by the recent shortage of gasoline on the Pacific Coast. In substance, each year we are consuming millions of barrels of oil more than we produce, and this deficit must be made to by importations. A careful analysis of the situation makes it evident that we need every barrel of oil that can be produced.Need for the Petroleum Production Engineer.Under present production practices perhaps 80% of the oil still remains in the sand. (See Lewis, J.O., Methods for increasing the recovery from oil sands, U. S. Bureau of Mines, Bulletin 148 p. 8.) Many wells are making water, and even whole pools are being flooded. The burning of fuels under field boilers is not generally efficient, and often gas is not made to do its full duty in bringing the oil to the well.In the past the producer has had to combat these and other problems single-handed. He has been too busy to give them special attention, and he has had little competent engineering advice. Oil, gas, and water occur underground according to certain natural laws. Undoubtedly an engineer, who is familiar with production practices and understands the fundamentals of the accumulation of oil and gas, can be of service to the producer by specializing on certain problems with a view of getting mare oil from the sand. In every other enterprise of similar magnitude the engineer is regarded as a necessary unit to its operation, and he should be so in the production of oil. His field of work should extend to every phase of production in which science and engineering and geology"

Sep 1, 1920

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By Hugo E. Camargo

Noise Induced Hearing Loss (NIHL) is the most common occupational disease in the U.S. with devastating consequences particularly in the mining industry. A study conducted by the National Institute for Occupational Safety and Health (NIOSH) revealed that 90% of coal miners have hearing impairment by age 50, compared to only 10% of those not exposed to occupational noise. According to the Mine Safety and Health Administration (MSHA), Continuous Mining Machine (CM) operators account for 30% of workers exposed to noise doses exceeding the Permissible Exposure Level (PEL). This number becomes more dramatic considering that 49% of the total national underground coal production is extracted using these machines. In this context, NIOSH is conducting research to identify and control dominant noise sources in CMs. Previous noise source identification was performed using a Brüel &Kjær (B&K) 1.92-m diameter, 42-microphone phased array. These measurements revealed that the impacts from the conveyor chain onto the tail roller, and the impacts from the conveyor chain onto the upper deck are the dominant noise sources at the tail-section of the CM. The objectives of the work presented in this paper were: 1) To rank the noise radiated by the different sections of the conveyor, and 2) to determine the effect of a urethane-coated tail roller on the noise radiated by the tail-section. This test was conducted using an Acoustical and Vibrations Engineering Consultants (AVEC) 3.5-m diameter, 121-microphone phased array. The results from this new test show that a urethane-coated tail roller yields reductions in the tail-section of 2 to 8 dB in Sound Pressure Level in the frequency range of 1 kHz to 5 kHz. However, integration of the acoustic maps shows that the front-section and mid-section of the conveyor also contain dominant noise sources. Therefore, a urethane-coated tail roller in combination with a chain with urethane-coated flights that reduces the noise sources in the front and mid sections of the conveyor is required toyield a significant noise reduction on the CM operator?s overall exposure. These results show the applicability of phased array technology for low frequency noise source identification.

Jan 1, 2008

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920

By M. J. Ankeny, J. J. Forbes

The United States Bureau of Mines often receives inquiries from the mineral , petroleum , and allied industries concerning the essential steps to be taken in the formation of Holmes Safety chapters and councils . The purpose of this circular is to answer in a general way such inquiries and to relate briefly the history and work of the Holmes Safety Association to the present date .

Jul 1, 1931

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By Charles Seitz

The Bureau of Mines has modified its parts-per-billion helium-4 analyzer to improve the analytical capabilities of the instrument. The modifications resulted in the following improvements: (1) The analytical precision of the instrument for 10 consecutive analyses was improved to ±1 ppb at the 5,000-ppb helium-4 level, (2) the helium-4 sensitivity was increased almost tenfold, and (3) the minimum detectable limit for helium-4 was improved to 0.5 ppb. The modifications made to improve the instrument included replacing the ion-source control circuit with a direct-current solid-state design, controlling the temperature of the ion source, stabilizing and reducing the pumping rate of the vacuum system, and optimizing peak integration.

Jan 1, 1986

By M. G. Zabetakis

At ordinary temperatures and pressures methyl ethyl ketone (MEK)-air mixtures containing between 2.0 and 11 vol.-pct. MEK and methyl isobutyl ketone (MIBK)-air mixtures containing between 1.5 and 7.5 vol.-pct. MIBK are flammable. However, MEK-bromochloromethane (BCM)-air mixtures containing at least 6.2 vol.-pct. BCM and MIBK-BCM-air mixtures containing at least 7.0 vol.-pct. BCM are nonflammable. Also, MEK-BCM-air and MIBK-BCM-air mixtures containing less than 18.7 vol.-pct. oxygen are nonflammable. To assure the formation of nonflammable mixtures when mixed with air, MEK-BCM vapor mixtures must contain at least 1.6 vol. BCM per volume MEK, and MIBK-BCM vapor mixtures must contain at least 2.8 vol. BCM per volume of MIBK; these quantities of BCM would be produced by liquid mixtures containing 55 vol.-pct. BCM in the first case and 60 vol.-pct. in the second. An MIBK-BCM-trimethylene chlorobromide mixture containing equal volumes of each liquid forms nonflammable mixtures with air at ordinary temperatures and pressures. The same is true of a liquid mixture containing 34.6 pct. (liquid volume) BCM, 34.b pct. perchloroethylene, 15.4 pct. MIBK, 7.7 pct. toluene, 3.85 pct. ethyl amyl ketone, and 3.85 pct. trimethylene bromide.

Jan 1, 1960