Search Documents

By Jingcheng Li

Currently many underground coal mines worldwide have installed or been planning to install a tracking system to trace miners mainly for their safety. Although many systems have been reported functional, a lack of sophisticated and systematic error correction methods apparently is still an issue for them; often it results in a low system resolution. To improve the system resolutions, this paper introduces two position adjustment methods for mine tracking systems. The first is an entry-matching method that optimally adjusts an off-course tracking device to the closest tunnel (entry). The second is a distance measurement adjustment method that accurately adjusts the position of a tracking device along an entry according to a measured distance from the device to a reference point. The coplanar node-path network mine model is used as the foundation for the development of these two methods.

Jan 1, 2009

By T. E. Gray

This report describes the preparation characteristics of the more significant coalbeds in Butler County, Pa. It is one of a series planned to determine which coals are suitable for producing metallurgical coke, either as mined or after beneficiation. More than 2 million tons of coal was produced in Butler County in 1958, of which about 25 percent was cleaned mechanically in four cleaning plants. Updating the 1942 coal-reserve estimates made by Ashley to December 31, 1958, more than 1,266 million tons of recoverable coal reserves remain in the county in beds that arc 24 inches or more thick. The Upper and Lower Freeport, Upper, Middle, and Lower Kittanning, Clarion, and Brookville beds were selected on the basis of production and estimated minable reserves. Sample locations were chosen after a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Four samples each were collected from the Upper Freeport and Middle Kittanning beds, three samples from the Brookville bed, two, samples from the Upper Kittanning bed, and one sample each from the Lower Freeport, Lower Kittanning, and Clarion beds.

Jan 1, 1960

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By M. J. Ankeny, J. J. Forbes

Several sets of questions and answers on the fundamentals of first aid to the injured, based on the Manual of First-Aid Instruction of the United States Bureau of Mines, are now in use in various parts of the United States. Persons experienced in first-aid instruction believe that a standardized set of questions and answers will assist materially in preparing men for examin- ations conducted by the Bureau for first-aid certificates. Inquiries as to whether a set of standardized questions and answers is available have been made frequently by those training men for the Bureau of Mines examination for certificates. It is believed that the following list of 171 questions and answers com- piled directly from the manual will be useful to company officials and em- ployees who are engaged in cooperative first-aid training to qualify for Bureau of Mines certificates. The list may also be used by field men of the Bureau in training instructors preparatory to a cooperative training campaign and in examining classes or individuals for first-aid certificates. The page references in parentheses refer to pages in the Manual of First-Aid Instruction.

Oct 1, 1935

By Northcutt Ely

This volume summarizes mining and petroleum legislation in 45 African jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identification of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added. In countries where minerals are subject to control of states or provinces, those areas are considered separately from the central government.

Jan 1, 1974

By R. F. Zaffarano

Reservoir oil in the Greater Aneth area, Utah, part of the Paradox basin, was studied to detect variation in oil characteristics within the reservoir and to determine its relation to age of accumulation and fluid equilibrium. At least three subsurface oil samples were obtained from each of the four largest of five field divisions comprising a producing area of 45,000 acres. Height of the oil column in the Pennsylvanian Desert Creek zone is about 230 ft. In general, the oil characteristics were found to be uniform across the area, and averages were developed for use in engineering applications. Average saturation pressure was 1,780 psia; the oil was undersaturated at the initial reservoir pressure, 2,200 psia. Variation in saturation pressure shows a lack of complete fluid equilibrium and continuing diffusion of solution gas from the main body of the reservoir to two extensions linked by narrow arms. By assuming early accumulation, the time involved in this diffusion process was calculated to be about the same as the age of the reservoir formation. Cause of the concentration of gas in the main body is attributed to differential entrapment during accumulation of oil and gas from an exterior source.

Jan 1, 1963

By R. V. Ramani, R. Bhaskar

"The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.IntroductionAn airborne dust cloud is a complex system containing particles of varied size, density, shape and state of aggregation. The behavior of the particles is dependent on a number of complex physical mechanisms, often opposing in nature. The net interaction results in the ambient concentration. This size dependent behavior of particles contrasts with that of gases, an area quite widely studied.The term aerosol is used to describe clouds of microscopic and submicroscopic particles in air such as chemical smoke or particulate matter released from smoke stacks. An aerosol system can be regarded as an arbitrary element of volume filled with gas and suspended particles of possible highly variable physiochemical nature. The parameters that are used to describe an aerosol system include concentration, mass average velocity and particle mass and radius. In characterizing such systems, several assumptions are made. Among these is the assumption that particles are smooth, inert and rigid spheres. Again, for example, when the particles are in transport, the possibility of collision exists. As a result of the collision, the particles may coalesce to form larger particles. The probability of sticking is considered a known quantity (lady, 1970). In this paper, the application of the principles used in aerosol systems is explored for the study of the transport and deposition of fine coal dust in underground mines."

Jun 1, 1988

By A. J. Barry

A practical method has been developed and field tested which provides an estimate of the bearing capacity of mine roof and floor. The relationship between penetration of the strata and imposed loads is determined by in situ tests. Information of this type is needed to determine the maximum allowable pressure that may be applied by self-advancing supports on roof and floor of a longwall face without causing a punching type of failure.

Jan 1, 1970

By C. M. Flynn

The solubilities of sideronatrite [Na2Fe(OH)(SO4)2?3H20] and ferrinatrite [Na3Fe(SO4),&apos;3H2O] were determined by the Bureau of Mines in the Na2SO4-Fe2O3-H2SO4-H20 system at 25°, 40°, 60°, and 90° C. The solution compositions investigated ranged from Na+-Fe&apos;+ mol ratios of 0.5 to >100 (Na2SO4 saturation) and H+ -SO4 2-mol ratios of 0 to 1. O. The results are presented in the form of contour plots. The solubilities were determined by seeding supersaturated solutions of known composition with the specified solid phase to precipitate a substantial amount of solid. Water was then added in small portions to the solution until the last portion of the solid dissolved. Equilibration times at 25°, 40°, 60°, and 90° C were 2 days, 1 day, 8 to 16 h, and 2 to 4 h, respectively. The accuracy of the solubility data is estimated to be 1 to 2 pet. Low iron solubilities of <0.36 pct Fe2(SO4)&apos;, or 1 g Fe/kg solution, were obtained in solutions containing at least 8 pet Na2SO4 in the absence of H2SO4 or a total of at least 36 to 38 pet Na2SO4 + H2SO4 at high acidity. The filterability and density of sideronatrite and ferrinatrite in comparison with other iron compounds are reported. These compounds are suitable vehicles for iron removal in Na2SO4-rieh solutions. Additional solubility data on the Na2SO4-H2SO4-H20 system were also obtained.

Jan 1, 1987

By Miro Mihelich

The mines and prospects in the vicinity of Landlocked Bay, 25 miles southwest of Valdez, Alaska (fig. 1), were examined, mapped, and sampled in July and August 1955 as part of a comprehensive investigation by the Bureau of Mines of ore deposits adjacent to Prince William Sound. The purpose of the investigation is to establish and record the location, nature, extent, and metallurgical characteristics of copper and associated metallization in the Prince William Sound district and to indicate, if possible, those areas in which additional exploration and development may be justified. Of particular interest are the possibly numerous deposits of massive iron sulfides that were neglected during early mining operations. These deposits may constitute important reserves of sulfur and iron. At Landlocked Bay deposits of copper-bearing iron sulfide minerals have been mined or partly explored through mine workings, which are in a zone about 1 mile wide along the western side of a large overthrust fault known as the Landlock Overthrust. Eight of the principal mines along this zone were examined end sampled. Although only three of the mines have a recorded production of shipping-grade copper ore, all have deposits of copper-bearing iron sulfide minerals that are similar in occurrence. The deposits occur as lenticular masses and disseminations of chalcopyrite, pyrite, and pyrrhotite which replace crushed rock or fill cavities along shear zones in greenstones and in sedimentary rocks that are exposed between sea level and an altitude of 2,500 feet. These lenticular masses of sulfide minerals range in size from small pods to ore bodies that have been stoped to maximum widths of 9 feet, strike lengths up to 70 feet, and dip lengths as much as 350 feet. Where accessible for sampling,, the copper content of the deposits ranged from a few hundredths of a percent to over S percent; zinc, gold, and silver are present in negligible amounts. Flotation tests of a sample composited to represent typical mine-run ore indicate that 81 percent of the copper is recoverable in a product assaying 28 percent copper at a concentration ratio of 17.5 : 1. INTRODUCTION Statistical records indicate that approximately 110,000 tons of metallic copper (about 16 percent of total Alaskan production) was produced from mines adjacent to Prince William Sound during the 40-year period ended in 1938. Although the principal production was from a large-scale mining and milling operation on Latouche Island (Kennecott Copper Corp., Beatson mine), a substantial amount of the total copper was derived from direct-shipping ores selectively mined or hand-sorted from numerous other deposits in the district. No production has been made since 1938; many of the claims have long been abandoned, and mine workings are either caved or deteriorating rapidly.

Jan 1, 1957

By John Nagy

The Bureau of Mines adapted thermal theories explaining combustion of gases to correlate parameters affecting ignition of dust dispersions. The dust dispersions were ignited in a Godbert-Greenwald furnace at atmospheric pressure. Ignition temperature and the concentrations of fuel, admixed inert powder, and atmospheric oxygen were related mathematically. Values for these parameters obtained in laboratory experiments for cornstarch agreed with theory. The developed equation permits extrapolation; the predicted upper igni-tion limits correspond with limited experimental data from laboratory and large-scale tests. Explanation of the effect of fineness of dust on ignition parameters is attempted by introducing a surface-area constant to modify the activation energy. Arguments are presented to show that the ignition process is a solid-gas phase reaction rather than an ignition of prevolatilized gases.

Jan 1, 1966

By Paul M. Tyler

[This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of specified French possessions in Africa has been prepared from the best information available in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. France controls large areas on the African continent, but the various Colonies and Dependencies are administered more or less independently. Algeria is under the direct jurisdiction of the Ministry of the Interior, and its mining laws are essentially the same as those of the mother country. Tunis and Morocco are attached to the Ministry of Foreign Affairs; separate digests of the mining laws&apos; of these respective colonies have already been prepared by the United States Bureau of Mines. The present paper covers all other French territory on the continent of Africa except Somaliland, a rather small Colony including the port of Djibouti near the point where the Red Sea joins the Gulf of Aden. Available information indicates that the prospects of mineral production in this Colony, apart from salt and gypsum, are not at all encouraging.3]

Jan 1, 1933

By Joseph M. Singer

Ignition of hybrid coal dust - methane - air mixtures by hot- turbulent - pulsedgas jets was investigated . The turbulent jets were generated by explosions in a primary chamber of stoichiometric mixtures of methane , oxygen , and nitrogen . The hot - gas ignition apparatus provided an adjunct means of testing , on a small scale , the type of ignition that exists in large - scale galleries or in coal mines . = coal particle The temperature Ignition variables were channel diameter , channel length , size , fuel concentration , and temperature of the hot - gas jet . of the hot jet was varied by changing the oxygen indices ( OI ) of the primary explosion mixtures . Coal dust having approximately 37 percent volatile matter was used . 02 O2ટ + N₂ The hybrid coal dust - methane - air mixtures required higher jet temperatures ( higher oxygen indices ) for ignition than the single fuel component methane - air mixtures . Methane in air concentrations less than the lower flammable limit of methane could be ignited in the presence of coal dust if the jet temperatures were increased . A specific explosion transmission ( ignitability ) curve existed for each coal dust concentration . The total fuel concentrations at the lower limit of each ignition curve was always close to or greater than stoichiometric , indicating that not all the coal dust was involved in the ignition .

Jan 1, 1964

By I. L. Nichols, K. C. Dean, P. H. Johnson

Hydrochloric acid , sulfuric acid , and chloridizing roast- water leaching methods for dissolution of cesium and rubidium from Maine , Canada , and Southern Rhodesia pollucite ores and their flotation products were investigated by small- scale tests . Optimum conditions were determined to be ( 1 ) for hydrochloric acid leaching , use 12.7 equivalents of 8.8 normal acid per equivalent of cesium in the sample and leach for 6 hours at 100 ° C ; ( 2 ) for sulfuric acid leaching , use 12.7 equivalents of 14.4 normal acid and leach for 2 hours at 120° C ; and (3 ) for chloridizing roast - water leaching , roast minus 200 - mesh ore, limestone , and calcium chloride in a ratio of 2 : 4 : 1 , respectively , for 1 hour at 900 ° C , and leach the calcine for 1 hour at 80 ° C with enough water to give 35 pct solids . Extractions of cesium from ores and flotation products containing over 20 pct cesium were in excess of 97 , 93 , and 96 pct for the hydrochloric acid , sulfuric acid , and chloridizing roast - water leach processes , respectively .

Jan 1, 1964

By Alla D. Mah

Compilation of data on materials of metallurgical interest is one of the important activities of the Berkeley Thermodynamics Laboratory of the Bureau of Mines. Recent renewed interest in metallurgy of vanadium renders the present compilation a timely guide for experimentation to improve present methods or to develop better methods of extractive metallurgy. Thermodynamic data for vanadium and its inorganic compounds have been critically surveyed, selected, and compiled into one convenient reference from which information can be readily obtained for evaluating heat balances, determining trends, and establishing limits of metallurgical processes. By indicating the direction of experimentation, this report enables the saving of time, effort, and expense which would otherwise be necessary for trial and error experimentation. Much of the data has been obtained experimentally at the Berkeley laboratory. Other data were collected through an extensive survey of worldwide literature through April 1965. Estimates were made when no data were avail-able. Data on the vanadium halides was sparse, and the results derived from existing data were at times divergent. Some of the selected values for the halides may need modification as more or better experimental data become available.

Jan 1, 1966

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease &apos;of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By H. W. GILLETr, E. L. Mack

The production of small heats of alloy steels on an experimental scale is often desirable in beginning the study of new alloy steels before large amounts of expensive alloys are used in heats of commercial size. Such small heats can sometimes be made up at crucible-steel plants, but few crucible-steel makers care to undertake experimental heats for other firms. Small electric furnaces offer some advantages over crucible furnaces for experimental work. Hansen1 in 1909 described a small 100-kilowatt single-phase, direct- arc furnace with a capacity of 50 to 300 pounds of steel, and such furnaces, of 200 pounds capacity or larger, are being successfully used by various firms for experimental work. They have the advan- tage of using the same metallurgical procedure as is used in prac- tice for larger electric furnaces. The very small sizes have the draw- back of lack of precision in controlling the carbon content of the steel. Small Rennerfelt two-phase, indirect-arc furnaces of 40 to 60 kilo- watts and small Industrial Electric Furnace Co. furnaces, single- phase with one electrode embedded in the hearth, of 25 to 50 kilo- watts, are also in use by a few firms for experimental work or for production on a very small scale. Hoskins carbon-plate resistor crucible furnaces are also sometimes used. Little seems to have been published on the use of these furnaces in making experimental alloy steels. Keeney' has given data on the making of uranium steels in a tilting Siemens furnace of 25 pounds capacity, and has described a small stationary Siemens furnace.

Jan 1, 1922

By John E. Miller

A high accuracy Burnett apparatus for use at 12,000 psi and 0° to 65° C has been constructed at the Bureau of Mines Helium Research Center. The apparatus is patterned after Burnett&apos;s original apparatus, but the working pressure is much higher and elastic distortion can be essentially eliminated. An operating procedure to permit faster experimental measurements is suggested.

Jan 1, 1967

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.