Search Documents

By H. B. Carroll

This Bureau of Mines report evaluates the performance of commercially available portable instrumentation for the detection of carbon monoxide, carbon dioxide, oxygen, and methane at conditions simulating an industrial work atmosphere. Portable instrumentation included in the study was gas-detection tubes (length-of-stain and color intensity), catalytic detector, liquid absorption detectors, paramagnetic oxygen detector, galvanic detector, and pelement or hot-wire methane detectors. Evaluation of the instruments was in atmospheres with 50 and 80 percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the thresh-old limit value. Correlation of the results from the portable gao analyzer with measurement from the standard instruments was made by calculating and plotting an estimated line of regression, prediction, and confidence limits and the correlation coefficient for each detector system. Relative humidity in the 50-to 80-percent range did not appear to contribute to instrumental uncertainties in either performance or operation. Considerable deviation in detection precision between the portable gas-detection systems and the standard systems was established, especially at the lower gas concentration levels. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than difference in the tubes themselves.

Jan 1, 1973

By Robert H. Merrill

Several investigators have obtained solutions for the concentration of stress around circular, ovaloidal, elliptical, and rectangular holes in an elastic, isotropic, semiinfinite plate subjected to uniaxial and biaxial stress. These solutions are used to evaluate the changes in stress around openings immediately under the undercut normally used in conventional block caving operations. The evaluations are based on the assumption that a horizontal undercut removes most of the vertical component of a biaxial stress field. The location and magnitude of the significant changes in stress concentration around the opening are computed. Conditions under which the assumptions used in the evaluations may or may not be consistent with conditions around block caving mines are discussed, and examples of preferred opening shapes for a biaxial (hydrostatic) stress field are shown. This report is a summary of one phase of an investigation to establish design methods for the size and shape of mine openings used in block caving mining methods .

Jan 1, 1962

By Keith A. Heasley, John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U. S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of are corded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with bump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip, etc.) of the failure of the strata surrounding the active and multi-panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

By R. S. Nutter

The results of designing, constructing, and laboratory testing of a modular, distributed, microprocessor-based mine monitoring and control system are presented. A standard computer communications protocol (DDCMP) was utilized throughout the system. Tests were performed on the utilization of a high-level language for programming mine monitoring and control systems. Laboratory tests were run on a combined air velocity/methane sensor.

Jan 1, 1980

This report presents information developed during Bureau of Mines contract H0242016, "Mine Shaft Fire and Smoke Protection Systems" from May, 1974 through June, 1975. Purpose of the metal and nonmetal health and safety project was to evaluate mine shaft fire and smoke hazard problems, and to develop and demonstrate a low-cost, reliable mine shaft fire protection system that would protect against such hazards and would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines. Program effort proceeded through five phases, culminating in the successful in-mine fire demonstration of a prototype system. In addition to this final report, a film is available which depicts components of the system and its successful shaft fire testing at an underground mine.

Jan 1, 1975

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Laurance L. Oden

The Bureau of Mines is developing nickel catalysts for converting synthesis gas derived from coal to synthetic natural gas. The present report describes the relationship between the composition of aluminum-nickel alloys in the composition range NiAl3 to Ni2Al3 equilibrated at 840° C and the properties of catalysts obtained from them. Methanation activity was determined in the temperature range of 300° to 360° C in a flowing gas stream containing 1 pct CO, 8 pct H2, and the remainder He. One part per million of H2S was added to the gas stream at 400° C to evaluate the susceptibility of catalysts to sulfur poisoning. The total surface area was measured by the adsorption of nitrogen at liquid nitrogen temperature, and the active surface area was measured by the adsorption of hydrogen at room temperature. Total surface area and active surface area were found to increase with increasing proportion of aluminum-saturated Ni2Al3 in the precursor alloy, but methanation activity and resistance to poisoning by H2S were nearly constant. However, the methanation activity of the catalyst prepared from stoichiometric Ni2Al3 was less than half that of the other catalysts.

Jan 1, 1978

By Patrick D. Plumb

The Juneau Office of the U.S. Bureau of Mines has undertaken a study of the environmental permitting process for major mines in Alaska to identify the effects ecosystem management has had or could have on the permitting process. To date, ecosystem management affects major mine permitting in Alaska primarily through the NEPA environmental assessment process. In Alaska, only the Forest Service has instituted ecosystem management in an overt and organized manner, while other agencies are doing so less directly. In recent Bureau of Mines publications, the mine permitting process has been described using case studies of several recently permitted mines in Alaska. The insights into the permitting process and the conclusions of these reports are reviewed and summarized. Several ecosystem management issues were identified in the case studies, including the need for: effective communication between agencies; standardization and coordination of NEPA environmental impact assessment and environmental monitoring programs among agencies, and assessment and selection of alternatives based on risks to ecosystems regardless of jurisdictional boundaries or environmental media-specific regulations. Ecosystem management could be used as a way to systematize, organize, standardize, and coordinate permitting and monitoring requirements and management perspectives among government agencies and project proponents.

Jan 1, 1993

This Bureau of Mines report describes research on methods of assuring the continued safety of mine electrical power distribution circuits through reliability and quality assessment of the protective devices, innovative inspection techniques for these devices and the circuits themselves, novel applications of trolley line circuit breakers, and computer modeling of distribution systems to determine the proper ratings for cables, power sources, and circuit protective elements. Battery charger safety is included.

Jan 1, 1979

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By V. B. Dale

San Manuel has been a modern prodigy from its inception to its present status as a block-caving operation producing 33,000 tons per day. The deposit was discovered, prospected, and developed with modern techniques, and nearly all planning was done from results of an extensive drilling program through an average overburden of 670 feet. The Federal Government had a prominent part in the discovery and primary development of San Manuel. The first 17 holes were drilled by the Bureau of Mines, and discovery of the large, low-grade, disseminated copper deposit is credited to the Bureau. A loan fund of 94 million was granted through the Reconstruction Finance Corporation to the San Manuel Copper Corp. for development of the deposit and erection of concentrating and smelting facilities. Then, while the mine was still being developed, the Defense Materials Procurement Agency contracted to buy a large amount of copper at a pegged price.

Jan 1, 1962

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objective and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the following material is presented: (i) review of related literature, (ii) mathematical models to perform quantitative analyses of accident/ injury experience data using the tools and techniques of risk analysis, time series analysis, and the Markov process, and (iii) descriptions of the HDBSEL and ACIM programs which are used to perform accident/injury experience analyses and cost analyses, respectively.

Jan 1, 1993

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

By P. C. McWilliams

Theoreticians in soil mechanics have been pursuing a probabilistic approach to the factor of safety of an embankment or darn for the past 10 years. The motivation for this work is in contrast to the current practice of deterministically computing a factor of safety and treating it as an absolute with no regard to its inherent statistical variability. Basic to the probabilistic approach is the selection of an appropriate statistical model to represent the histogram or probability density function (PDF) of the factor of safety values, Rather than simply assuming which PDF is appropriate, the Bureau of Mines collected data at two waste disposal embankments for consideration, This report addresses three candidate models, using the techniques of nonlinear curve fitting, and identifies the "best" model. A propagation of error formula for estimating the variability of Fellenius? factor of safety is also discussed.

Jan 1, 1983

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

By W. L. Falke

The Bureau of Mines has developed a system that permits the "soft" soldering of aluminum and aluminum alloys with standard tin-lead solders. The method employs application of a thin nickel-copper-alloy coating to the substrate, which enables the tin-lead solders to wet readily and spread over the areas to be joined. With conventional technology, aluminum and aluminum alloys are extremely difficult to solder because tenacious surface oxide films prevent wetting. With the Bureau-developed method, the aluminum substrate is mechanically or chemically cleaned to facilitate bonding to a minute layer of zinc that is subsequently applied with an electroless zincate solution. The nickel-copper-alloy (30 to 70 pct Ni) coating is then applied electrolytically over the zinc, using immersion cell or brush-coating techniques. Development of acetate electrolytes has permitted deposition of the proper alloy coatings. The coated areas can then be readily joined with conventional tin-lead solders and fluxes. The joints so formed are ductile, strong, and relatively corrosion resistant, and exhibit strengths equivalent to those formed on copper and brass when the same solders and fluxes are used. The method has also been employed to soft-solder magnesium alloys.

Jan 1, 1983