Search Documents

By Joseph J. Wallace

1. The Pittsburgh is the most important bed in Washington County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 4,181 million short tons as of January 1, 1954. Of this total, 4,132 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By E. C. Lane

This report presents the results of the Bureau of Mines' twenty-first semiannual survey of motor gasoline marketed in the United States. The 12 cities in which samples were collected have teen chosen as representative of the more important marketing territories, as it is obviously impractical to obtain a sample of every gasoline sold in the entire country. The survey reveals that the motor gasoline which is being marketed in the United States this winter is decidedly more volatile than that sold a year ago. Samples from all cities show a decided improvement in volatility except those from Laramie, Wyo., which show a small decrease in volatility.

Jan 1, 1930

By W. E. Cooper

The International Intercalibration and Intercomparison Program (HIP), consisting of several selected laboratories from four countries, held a radon progeny intercomparison measurement at the U.S. Bureau of Mines experimental Twilight Mine on September 12-14, 1988. Grab samples were taken at four different conditions of low and high radon progeny and condensation nuclei concentrations, respectively. The results showed good agreement among all seven participants. The coefficient of variation of all measurements was 4.7%; after minor corrections for flows and some systematic biases, it was reduced to 3.2%.

Jan 1, 1990

By J. E. Schiller

The Bureau of Mines has investigated the surface charge of amphibole asbestos fibers and nonasbestiform cleavage fragments, as part of the Bureau's fundamental studies to provide new knowledge on the physical and chemical properties of the amphibole minerals. Microelectrophoresis was used to measure the electrophoretic mobilities, in water, of particles from six asbesti-from amphiboles and seven nonasbestiform amphiboles over the pH range of 5 through 9. The particles generally ranged in size from 2 to 5 µm wide by 10 to 30 µm long. The isoelectric point was determined for four of the minerals, and values were found to be between pH 3.5 and pH 5. The minerals studied had zeta potentials that generally ranged from -25 to -so mv in neutral solution. Attachment of colloidal positively charged AgI was also studied as a means of determining surface charge. Scanning electron microscopy of amphibole particles that had been in contact with aqueous AgI showed equal attachment of AgI to asbestos fibers and to cleavage fragments; the extent of AgI coating was the same for both. The electrophoretic mobilities of asbestos fibers were essentially the same as those of elongated cleavage fragments of the same aspect ratio (particle length divided by width). Blocky particles from both asbestiform and nonasbestiform specimens had lower mobilities.

Jan 1, 1980

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952

By Carlton E. Brown

In 1935 , Brown and Yant / described a microprojector ( microscopic arrangement for projecting images on a screen ) for use in counting and measuring the size of dust particles in Owens - jet dust - counter and simila dry samples of dust collected from the air . In 1938 Brown and others , described a modification of this microprojector that could be used also in counting dust in impinger samples . Microprojectors of this second type have been set up by many mining companies and others and have been made commercially available . Hamly and Pullen5/ described a modification of this microprojector for use in making rapid comparative estimates on konimeter samples and other determinations . This report contains information on still another modification named the "midget microprojector " because of its small size .

Sep 1, 1944

By L. O. Bacon, H. R. Joesting, J. H. Getz

"INTRODUCTION For a number of years manganiferous iron ore has been mined on a small scale at Boston Hill, in Grant County, N. Mex. Total production up to 1943 is estimated to be over 793,000 long tons, containing 8 to 35 percent manganese and 26 to 46 percent iron. 4/ During 1941 to 1943 production was estimated to be 206,000 long tons, containing about 13 percent manganese and 37 percent iron. During 1944 daily production was several hundred tons, mostly from a single open pit. Several moderately large deposits have been mined: and many smaller ones have been found.From February to April 1945 geophysical surveys were carried out on Boston Hill by the Division of Geophysical Exploration, in cooperation with District 5, Central Region, Bureau of Mines, to determine if hitherto undiscovered manganiferous iron deposits exist. Field work was interrupted for a total of about 1 month during this period by work on other projects in nearby areas. Previous to the geophysical surveys, a preliminary examination was made by H. R. Joesting to determine if geophysical methods could be utilized in exploring the area. 5/Field measurements were made by L. O. Bacon and J. H. Getz, project geo¬physicists of the Bureau of Mines, under the general supervision of H. R. Joesting. A grid survey of the area, to locate geophysical stations, was made by Paul Russell, Bureau of Mines engineer, who also collected specimens for laboratory tests. Most of the computations and the preliminary magnetic and resistivity maps were made by L. 0. Bacon."

Feb 1, 1948

By Raymond W. Hiteshue, Sam Friedman, Martin D. Schlesinger

The Bureau of Mines in cooperation with the El Paso Natural Gas Co. investigated the effect of high temperature and pressure at short residence times on the hydrogenation of a New Mexico coal to gaseous and liquid hydrocarbons . The study was made in a bench - scale semicontinuous unit at pressures of 500 to 6,000 psig , 480 ° to 1,000 ° C , and residence times of less than 1 minute to 15 minutes . Ammonium heptamolybdate was impregnated on the coal to furnish 1 percent molybdenum based on maf coal . Coal could be rapidly hydrogenated at elevated temperatures and pressures to yield large quantities of gaseous hydrocarbons and small quantities of lowboiling oils , high in single - ring aromatics . At 800 ° C and 6,000 psig and a residence time of 1 minute , the yield of hydrocarbon gas was 43 percent and of liquid hydrocarbons 9 percent , based on maf coal . With a 15 - minute residence time , the yield of gaseous hydrocarbons increased to 68 percent with a decrease in yield of oil to 6 percent . At higher hydrogen velocities , the yields of oil were much greater but contained large quantities of asphaltene . Low concentrations of molybdenum (0.01 and 0.1 percent ) or a high concentration of iron ( 1 percent ) were ineffective at 800 ° C , 6,000 psig , and short residence time .

Jan 1, 1964

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

A series of economic evaluations of processes for producing metallurgicalgrade alumina from low- grade aluminous materials is being conducted by the Bureau of Mines to determine the relative processing costs . The two processes considered in this evaluation are concerned with the recovery of alumina from clay through the formation of ammonium alum . In the first process , dehydrated clay is leached with ammonium bisulfate solution ; in the second process , clay is baked with ammonium sulfate and then leached with water containing a small quantity of sulfuric acid . After the alumina is dissolved by either of these methods , the iron is reduced to the ferrous state to avoid crystallization of ferric sulfate with the alum . The recovery of pure alum requires two crystallization steps . The alum crystals are then redissolved and precipitated with ammonia to produce alumina hydrate , which is calcined to a - alumina . These evaluations are based on published work , and the proposed plants are designed for a capacity of 1,000 tons of alumina per day . The estimated operating cost per ton of alumina for the bisulfate leaching process is $ 117.06 , and for the sulfate baking process , $ 109.26 . Using a Marshall and Stevens chemical equipment index basis of 240.0 , the estimated fixed capital costs , in the same order , are $ 158 million and $ 146 million . Under current economic conditions , these two processes are not competitive with the Bayer process for the production of alumina from bauxite . Since small improvements will not reduce costs sufficiently to approach competitive costs , future research work with these processes should be confined to areas likely to result in major cost reductions .

Jan 1, 1965

By H. M. Thorne

Oil shale, a potential source of products presently obtained from petroleum, is found in many countries. The most extensive known deposits from the standpoint of potential shale oil in place are those in Brazil and the United States of America. Mining methods used for oil shale range from open-pit operations for shallow deposits to room-and-pillar and longwall techniques for deposits with thick overburdens. Oil shales from different sources vary greatly in the amounts and types of organic and inorganic constituents. By retorting, the organic material is converted to oil, gas, and coke. The largest percentages of oil are obtained from materials having the highest hydrogen content. Over 2,000 retorting systems have been patented, but only a few have been used industrially, and no single process seems best for all types of shales or economic conditions. Shale oils have different characteristics, depending on the source rock and method of retorting. They contain large quantities of olefinic hydrocarbons and more oxygen, nitrogen, and sulfur derivatives of hydrocarbons than most petroleums. Consequently, petroleum refining methods usually must be modified for shale oil. This is particularly true in catalytic processing. Hydrogenation, even under mild conditions, improves shale-oil refinability. Several byproducts may be obtained from both the retorting and refining steps.

Jan 1, 1964

By Rena I. Geroyan

This U.S. Bureau of Mines report presents an evaluation of the coal mining industry's impact on the economy of Pike County, KY. A software package called IMPLAN was used to perform the analysis. The results of this study show that coal mining was the primary income producing industry in Pike County in 1990, accounting for about 46% of the county's Total Industry Output, and 21% of the total employment.. Coal production in that year amounted to 29.6 M mt (32.6 M st). Two alternate economic scenarios were developed to study the potential effects of changing coal market conditions on the county. Scenario A assumes market changes result in a coal production increase of 4.5 M mt/yr (5.0 M st/yr), and scenario B assumes a decrease of 4.5 M mt/yr (5.0 M st/yr). Scenario A would result in a 15.3% rise in the value of Pike County's Total Industry Output, adding a total of 1,663 jobs (+6.1%) in all sectors in the county. Scenario B would have the opposite effect, decreasing the Total Industry Output and employment by identical amounts. Such knowledge would allow local and regional officials to anticipate the economic and social impacts of shifts in coal production, and plan accordingly to mitigate impending changes.

Jan 1, 1994

By N. S. Dalal, V. Castranova, X. Shi, W. Wrr, V. Vallyathan

"SUMMARY Data presented here indicate that freshly fractured silica exhibits surface characteristics and biologic reactivity distinct from aged silica, and on this basis we propose that these surface features may lead to enhanced manifestations of lung Injury. Grinding of silica produces ~10"" Si and SI-O (silicon-based) radicals per gram of dust on the particulate surface which are characterized by an electron spin resonance (ESR) spectrum centered around g = 2.0015. These silicon-based radicals react with aqueous media to produce OH radicals, which are demonstrable using a DMPO spin trap. The concentration of silicon-based radicals in silica decreases with aging in air and exhibits a half-life of ~30 h, whereas its ability to generate OH radicals in aqueous solution decreases with a half-life of ~20 h. However, on storage in aqueous media, the concentration of silicon-based radicals end the dust's ability to generate OH radicals decrease significantly within a few minutes. Freshly ground silica is also more biologically reactive than aged silica, because freshly crushed silica activates a greater respiratory burst In alveolar macrophages than aged silica, i.e., storage of ground dust in air decreases silica-Induced superoxide anion secretion, hydrogen peroxide release, and NBT reduction by 25%, 68%, and 43%, respectively. Furthermore, compared to aged silica, freshly ground silica exhibits a greater cytotoxic effect on cellular membrane Integrity, i.e., a 1.5-fold increase in LDH release from macrophages, a 36-fold increase in hemolytic activity, and a three-fold increase in the ability to induce lipid peroxidation. Because acute silicosis is frequently associated with occupations in which freshly fractured crystalline silica of respirable size is generated, the present study suggests that fracture-generated silicon-based radicals may play a significant role in the pathogenesis of this disease. AM REV RESPIR DIS 1955; 133:1213-1218IntroductionOccupational exposure to crystalline silica can be associated with either chronic or acute pulmonary disease. Chronic silicosis becomes manifest 20 to 40 years after first exposure and is characterized by development of concentric hyalinized nodular lesions in the lung with the de-velopment of dyspnea over a period of several decades. Acute silicosis, on the other hand, is manifested by a rapid on-set after exposure and is characterized by the accumulation of an amorphous granular lipoprotein exudate in the airspaces and rapid development of respiratory disability within a few years (1-3).Information is growing concerning the etiology of chronic silicosis. Studies sug-gest that several mechanisms may be in-volved in the development of fibrosis. Lung injury may result from silica-induced release of lysosomal enzymes from alveolar macrophages (4, 5). In ad-dition, silica-induced activation of su-peroxide anion and hydrogen peroxide release from alveolar macrophages may result in oxidant-induced damage to lung parenchyma (6). Silica exposure can also result in the release of mediators from alveolar macrophages which enhance the proliferation of fibroblasts and the syn-thesis of collagen by these pneumocytes (7, 8)."

Jan 1, 1988

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By Ronald H. Church

The Bureau of Mines tested & ground penetrating radar (GPR) system in the central Florida phosphate district. to determine the feasibility of utilizing GPR technology for subsurface cavity detection. The test area is located in karst topography where sinkhole development is prevalent. State regulations require subsurface drilling of damsites to identify underground anomalies; however, this method is not totally accurate in locating subsurface cavities that could lead to sinkhole development. An electromagnetic method of identifying anoma-lous subsurface conditions could reduce or eliminate the possibility of dam failure due to sinkhole development. The Bureau devised a GPR system that successfully penetrated over 50 ft of overburden and gave recognizable radar return signals characteristic of a rock-cavity interface.

Jan 1, 1986

By C. T. Baroch

As part of a general program for investigating all phases of titanium production, argon was substituted for helium in the reduction step at the Bureau of Mines pilot plant, which employed a modification of the Kroll, or magnesium-reduction, process. Argon was substituted for helium in 108 of the 140 batches of sponge made during 1 month's reduction operations for July 1954. Argon was substituted for helium satisfactorily, with only slight modifications in technique. Metal quality, feed rate of TiC14, magnesium efficiency, and average production per batch were closely comparable with either gas. Argon runs were slightly more troublesome because of the formation of condensable chloride complexes, which tended to plug feed and vent lines and to entrap deposits of lower titanium chlorides on the reactor-pot lids. These lower chlorides were objection-able because they were pyrophoric and created obnoxious fumes when pots were opened. When feed and vent lines became plugged care was required in poking or unplugging these lines to prevent air from entering the reactor. These problems were relatively minor, and continued development of reactors and techniques for the use of argon should further minimize objectionable side reactions obtained when argon is used.

Jan 1, 1956

By Robert M. Doerr

The purpose of the investigation was to determine the oxidation behavior of selected tungsten-cobalt alloys. Specimens of Wand W-Co containing 0.7, 1.7, 3.4, and 9.7 weight-percent Co were subjected to pure 02 at 1,000° and 1,100° K, and specimens of W-Co containing 29.8 weight-percent Co, at 1,100° K. Reaction kinetics were determined volumetrically. For specimens other than those containing 29.8 percent Co, the reactions proceeded at about a constant rate at either temperature, indicating the formation of a scale of constant protectivity; the reaction rates were essentially independent of the Co concentration. The scales on these alloy specimens consisted principally of WO3 and CoWO4. Specimens of a 29.8 weight-percent Co alloy, consisting primarily of the W6CO7 phase, oxidized with only slight deviations from the parabolic rate law at 1,100° K. The protective scale on these specimens consisted chiefly of Co3O4, CoW04, and W1 8°49; Co3O4 was outermost, and the W18O49 was adjacent to the alloy. The results suggest that the Co-rich outer scale inhibited the inward transport of 0 to an extent sufficient to greatly limit the amount of the nonprotective WO3 formed, so that protective W18O49 formed instead.

Jan 1, 1967

By R. J. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of the California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1953 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline which include, for the second time in this series of reports, data on some samples of grade 108/135 aviation fuel. Data also are given for 32 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' production in their laboratories and the results sub-mitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 19 producers of aviation jet fuels are represented.

Jan 1, 1954

By P. M. Sullivan

Galvanizers' sal skimmings have been treated by two methods of leaching in attempts to produce preflux solutions suitable for use in galvanizing operations. Both water-leaching and acid-leaching procedures are effective, except in severely exhausted skimmings when water-leaching becomes impractical. A preliminary analysis of the skimmings is not required. Solutions in the recommended concentration range can be produced conveniently by control of pH, specific gravity, and chlorine content. A technician would require only a short period of training to be able to perform the operations described.

Jan 1, 1958

By John C. Holtz

"INTRODUCTION Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in mines is analyzed after blasting, and in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in a cooperative research 3/ that compared data obtained in the field with those obtained in the testing station, showed that the results were not in entire agreement. The production of carbon monoxide was found to be governed chiefly by the oxygen balance of the explosive, but the production of oxides of nitrogen did not change in so simple a manner. Because of the increasing interest in correlations between the composition of the explosive and the production of toxic gases, it seemed desirable to continue the investigation.PURPOSE OF INVESTIGATIONAs field tests are both time consuming and expensive and as field results are affected by factors that are not always under control of or clearly evaluated by the operator, the purpose of this investigation is to develop a testing-station procedure that will reproduce the gaseous products quantitatively under known conditions analogous to those that may be expected in the field. In addition, the factors affecting the formation of toxic gases, particularly oxides of nitrogen, will be studied,"

Apr 1, 1940