Search Documents

By M. L. Whisman

Three samples of waste lubricating oil were re-refined by processes developed by the Bureau of Mines and reformulated with additives to meet designated requirements for viscosity and service. Quality-defining bench-scale tests were used to compare and evaluate the quality of these three motor oils, eight commercially re-refined lubricating oils, and three new lubricating oils. Most of the re-refined oils studied could not be distinguished from new oils by the bench tests used to define quality. There was some evidence, however, that one and perhaps more of the re-refined products investigated might not meet all of the quality standards of new lubricating oil, suggesting the need for better quality controls by re-refiners.

Jan 1, 1974

By A. F. Baker

Tests were conducted in commercial foundries to determine the suitability of calcined anthracite as a cupola fuel. The calcined anthracite performed satisfactorily at two of the three foundries where iron-melting tests were conducted. Performance at the third installation was unsatisfactory because metal temperatures deviated widely and, in general, were lower than is desirable for the type of castings being made.

Jan 1, 1963

By C. M. Palencia

The Bureau of Mines evaluated the potential availability of molybdenum resources from 88 mines and deposits that account for more than 90 pct of the demonstrated resource base in market economy countries (MEC's). For each property, tonnage-cost relationships were developed that indicate the molybdenum potentially available at different average production costs, including a 15-pct rate of return on invested capital. From the 23 MEC primary deposits, 2.5 billion 1b Mo was determined to be potentially available at a price of $411b, rising to 4.7 billion 1b Mo at $8/lb. Copper price-molybdenum tonnage relationships were developed for those mines and deposits from which molybdenum can be recovered as a byproduct of copper production. This analysis showed that another 3.4 billion lb Mo is potentially available based on a copper price of $0.7511b, rising to 4.3 billion lb Mo at $l.00/lb. The United States has been the world's largest molybdenum supplier since 1924. Its remaining resources are sufficient to meet the domestic demand of 57 million lb/yr Mo (averaged for a 10-yr period) through the end of the century. Production from primary domestic mines was suspended during most of 1983 because of oversupply of materials. A major concern is the cheap molybdenum byproducts from foreign copper operations in which employment and the need for hard currency override economics in meeting production goals.

Jan 1, 1985

By Robert J. Brennan, Edward R. Navrocky, John W. Buch

In an effort to establish a highly productive mechanized mining system for anthracite beds pitching between 10 ° and 20 ° , for which conventional mobile equipment is not adaptable , the Bureau carried out an experiment in longwall mining using an Anderton- type drum cutter loader and friction - type yielding steel roof supports . The roof- support system proved to be inadequate for breaking the overhanging roof at the break line supports , with the result that the roof broke over the solid coal . The accompanying subsidence destroyed the continuity of the roof in the work area , and the project was discontinued .

Jan 1, 1964

By R. H. Sprute

The Bureau of Mines conducted a feasibility study and designed an operational system for consolidating waste coal sludge in a 110-acre pond by applying direct current between buried and floating electrodes. Consolidation would reduce the sludge to half its present volume, there-by extending the working life of the pond as well as creating a safe, stable impoundment. The project was conducted by the Bureau under an agreement with the Washington Irrigation and Development Co. (WIDCO), located near Centralia, WA. Part 1 of this report, published as Report of Investigation 8666 in 1982, covers the results of laboratory tests at the Bureau's Spokane Research Center and of a small-scale field test at WIDeO's coal preparation plant. Test results show the process is efficient and cost-effective when power is applied at low current density. Part 2 (this paper) describes a detailed design for an electrokinetic system to dewater WIDCO's 110-acre pond with a 27.4-acre electrode array. Densification of the inactive sludge pond will require 3.6 yr of treatment for a total cost of $1,450,000. The study and design are site specific, but design procedures and analyses are sufficiently detailed to serve as a guide for applying the process to any sludge pond.

Jan 1, 1988

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By Albert Mendelsohn

This paper, describing the mining practice at the Champion mine of the Copper Range Copper Mining Co., is one of a series of papers on mining methods and costs being prepared by the United States Bureau of Mines. Mining practice at the Champion mine has undergone considerable change during the last four years. Previous to that time the mine was worked by the horizontal out-and-fill method, the stopes starting near the shafts and advancing away from them (fig. 2). The floor pillars were mined by the inclined cut-and-fill method, working en the retreat or toward the shafts (fig. 1). At present the mine is being developed to .tope entirely on the retreat by a sublevel inclined cut-and-fill method.

Jan 1, 1931

By R. D. Wilson

Ten to twelve million tons of dust is produced by cement kilns annu-ally in the United States, resulting in a serious waste disposal problem. The Bureau of Mines investigated two alkali volatilization methods for converting this dust into materials for making portland cement and a useful potassium product. Portland cement kiln dust was found to be composed of finely ground cement raw materials (CaC03 and 8i02) having a layer of alkali sulfate (K2S04 and Na2S04). In this form, it cannot be directly recycled to cement kilns because concrete is weakened by a reaction between the alkali and the aggregate. Portland cements with 28-day strengths above 5,000 psi were produced from low-alkali residues using sintering and melting methods. For nearly complete removal of alkalies, primarily potassium sulfate, from cement kiln dust, a temperature above 1,300° C and a reducing atmosphere were required.

Jan 1, 1986

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

By Lloyd Williams

1. This investigation shows that the Sewanee bed is the only coal bed being mined in Sequatchie County. Other coal beds are present, but as they do not contain known recoverable reserves, estimates of reserves were made only for the Sewanee bed. 2. Known measured and indicated reserves in the Sewanee bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 76 million short tons as of January 1, 1953. Of this total 62 million short tons represent coal 28 inches and more thick. Areas in the bed were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1955

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A series of four coal combustion experiments was conducted at the National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Laboratory (PRL) in the Safety Research Coal Mine (SRCM) to evaluate the response of fire sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. An optical path smoke sensor alarmed earlier than a point type diffusion mode ionization smoke sensor which alarmed prior to a CO alert value of 5 PPM above ambient. The presence of steady state diesel emissions resulted in a decrease in the optical smoke sensor analog output voltage signal by less than 1.4 pct for the three coal fire experiments in which a diesel engine was operating, whereas the ionization smoke sensor output decreased between 10.8 and 26.7 pct after the initial surge of the diesel engine. A commercial diesel discriminating fire sensor did not alarm for a fire in the one experiment for which it was used. The results of the experiments demonstrated that an optical path smoke sensor might be used to detect a coal fire under the experimental conditions considered of starting a diesel engine followed by a slowly developing coal fire.

By J. C. Edwards, C. C. Hwang

A Computational Fluid Dynamics (CFD) program was used to model buoyancy induced Product-Of-Combustion (POC) spread from experimental fires in the National Institute For Occupational Safety And Health (NOSH), Pittsburgh Research Laboratory (PRL), safety research coal mine. In one application, the CFD program was used to predict spread from fires in an entry under zero airflow conditions. At a location, 0.41 m below the entry's roof at a distance of 30 m from the fire, the measured smoke spread rates were 0.093 and 0.23 m/s for a 30 and a 296 kw fire, respectively. The CFD program predicted spread rates of 0.15 and 0.26 m/s based upon the measured fire heat production rates. Based upon a computation with [c3h3] as the hydrocarbon fuel, a predicted 5 PPM co alert time of 70 s at a distance of 30 m from the fire is to be compared with the measured alert time of 148 s. In a second application, the CFD program was used to analyze smoke flow reversal conditions, and the results were compared with visual observations of smoke reversal for 12 diesel fuel fires. The CFD predictions were in qualitative agreement with visual observations of smoke reversal.

By Charles L. Kimbell

The final 26 tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-89 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1986-90, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1990. With the inclusion of silver and uranium in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-are included because of their significance as products.

Jan 1, 1993

By Eugene T. Sheridan

This circular presents data on individual plants of the fuel-briquet and packaged-fuel industries that responded to the Bureau of Mines annual economic survey and reported production for 1959. The companies named herein represent virtually all producers of processed fuels of mineral origin. A few small companies may not have been canvassed or failed to respond, however, as some plants operate intermittently, and the survey is voluntary. No consideration was given to size of the plant and all plants that reported commercial production were included. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, fabricated from fine-sized mineral fuels by mixing with binders and compressing into small individual shapes. Briquets usually are produced as small, pillow-shaped pieces, 2 to 4 inches long, weighing 2 to 4 ounces. Packaged fuel consists of 3- to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. The overall size of a popular package is 10-112 x 7 x 3-1/2 inches. Briquets are durable, may be stored outdoors, and shipped and used as bulk fuel. Packaged fuel is fragile, and must be stored indoors to keep it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times as a supplement to other fuels. Package fuel is burned without removing the paper and referred to as the "white-glove" fuel.

Jan 1, 1960

By Ivette E. Torres

Of the 15 selected non fuel mineral commodities detailed in table 12, only 3 indicated increases in worldwide consumption in 1992. As in 1991, decline in consumption levels of the selected commodities can be attributed to reduced levels of use in the former U.S.S.R. and Eastern Europe. Of the remaining 12 commodities, 2 magnesium and cadmium, stayed relatively the same, while the other 10, including iron and steel, all recorded decreases. Global consumption of iron ore is estimated to have fallen about 3.5 % or about 30 million tons. This is a greater decline than what was estimated for production of iron ore, which is down only 2.7% or nearly 26.5 million tons, suggesting an addition to stocks. The consumption trend for iron and steel has been declining since 1989. This has mainly been due to the continued drops in use in the former U.S.S.R. and Eastern Europe. Even as the European economy begins to turn upward, there may only be a slight increase in consumption of iron, steel, and cement, considering the high cost of construction needed to modernize factories and buildings in Eastern Europe. Many feel that the economies of these countries are limited by the current status of their industries.

Jan 1, 1994

By Charles B. Kenahan

A summary of Bureau of Mines research on utilization and disposal of solid wastes is presented, accompanied by an extensive bibliography of related publications. The Bureau's Solid Waste and Materials Recycling Program is directed toward four main areas of research, development, and demonstration: (1) extraction of mineral, metal, and energy values from urban refuse; (2) upgrading and recycling of automotive and related ferrous and nonferrous scrap; (3) utilization and stabilization of mine, mill, and smelter wastes; and (4) recovery and reuse of values from industrial waste products. A contract and grant program that supplements the in-house research and aids in the training of manpower in management of mineral-, metal-, and energy -based solid wastes is also discussed. This publication is an updating of Bureau of Mines Information Circular 8460 issued March 1970.

Jan 1, 1971

By Pamela J. Watson

A novel technique has been employed by the U.S. Bureau of Mines to determine the zeta potential of particles for a far-reaching series of material types in a wide variety of baseline waters, both alone and with many different chemical additives. The materials tested ranged from naturally occurring Sioux Quartzite and Tennessee marble to commercially produced magnesium oxide bricks. The waters tested ranged from ultrapure distilled, deionized water to municipal tap water and mine-site water. The chemical solutions tested included inorganic additives, such as aluminum chloride (AICI3) and sodium chloride (NaCl); organic additives, such as dodecyltrimethyl ammonium bromide (DTAB); and nonionic polymers, such as polyethylene oxide (PEO). The results of precise zeta potential determinations have application in a large number of laboratory studies as well as in various mining and processing operations.

Jan 1, 1989

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010

By Frank B. Fulkerson

A study was made of the economic factors governing silver production in the Coeur d'Alene mining region, Shoshone County, Idaho. Production and other statistics were analyzed. It was concluded that if the rapid rise in the open market price that began late in 1961 continues, greater production of the metal should result from the mines of the Coeur d'Alene mining region. However, the output gain would be limited, because costs per ton of ore mined would rise as production was increased beyond optimum capacity. Advances in the price of silver would increase the size of ore reserves by making some marginal ore profitable to mine and by providing greater funds for exploration projects that might result in discoveries adding to the reserves. Output of byproduct silver from Lead-zinc mining probably will not exceed 4.3 million ounces, judging from the trend from 1946 to 1961.

Jan 1, 1964