Search Documents

By W. A. Stickney

As part of a Bureau of Mines program to investigate recovery of manganese (Mn) from low-grade materials, laboratory studies were made of four samples of mill rejects: Three from Montana and one from Peru. These studies demonstrated that certain mill-waste products can be a potential source of manganese. Both manganese oxide and carbonate minerals were recovered by flotation in an acid circuit with a fuel oil-tall oil emulsion as collector. Sintering) required to prepare a physically acceptable product, also was used as a method of beneficiation. In addition to being low-grade, some of the samples presented problems of intimate mineral association and complex textures.

Jan 1, 1960

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By C. E. Lapple

To improve mine health and safety conditions, there is need for a portable instrument that mine inspectors can use routinely for rapidly checking concentrations of dust in mine atmospheres. On October 23, 1969, Stanford Research Institute was authorized by the U.S. Bureau of Mines to conduct a study aimed at developing such an instrument under Contract No. H0100186. The results of that study are reported in Technical Report No. 1, "Development of Portable Instrument For Measuring Coal Mine Dust Concentration," August 1970. In that study it was demonstrated on bench-scale that a near-forward optical scattering device gives a linear correlation between mass concentration and optical readout over a range of 2 to 200 mg/m3 with excellent reproducibility. The same correlation was obtained for the Respirable* dust fraction of three different coal dusts within ± 10% and an extreme spread of ± 30%. Based on these results a prototype instrument was designed which was expected to meet all the necessary requirements of a portable instrument for mine use. Because of the excellent results obtained, a further study was authorized by the Bureau of Mines on May 10, 1971 under Contract No. H0111688. The prime objective of this study was to build, calibrate, and deliver to the Bureau of Mines two prototype instruments based on the design previously developed. The emphasis was to be on providing instruments which would meet certain minimum standards of size, weight, response time, sensitivity, ruggedness, reproducibility, permissibility, and cost (ultimate); optimization of the design was to be considered only insofar as it would not significantly delay the development. One instrument was to be delivered after initial calibration of both instruments with Coal Dust PGH. The second instrument was to be used for further calibration with a number of other coal and rock dusts and for assessing other relevant performance characteristics. This report summarizes all the results of this second study.

Jan 1, 1972

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC) , on Contract H0122026 (which began in August of 1971) . Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of in- dependent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "seismic Detection and, Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By Robert C. Johnson

Single crystal whiskers of ZrO2 and TiO2 were grown by solution and crystallization of these oxides in molten baths. Mixtures of Na2B407 and LiC1 were the most suitable growth media for zirconia. Sodium borate alone and Na2CO3 plus SiO2 were best suited for titania. The solubilities of zirconia and titania in molten sodium borate were determined, Whether zirconia whiskers were dendritic or nondendritic depended on the temperature used. The best single crystal whiskers were grown below 1,100° C. Titania whiskers always grew as single crystals. The tensile strengths of zirconia and titania whiskers were about 15,000 psi and 50,000 psi, respectively. Modulus of rupture was about 49,000 psi for zirconia whiskers and 75,000 psi for titania whiskers. Chemical analyses showed the zirconia and titania whiskers to be pure. The zirconia and titania whiskers were shown by X-ray analysis to be, respectively, baddeleyite and rutile.

Jan 1, 1965

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

By A. E. Sands

The Bureau of Mines, S. Department of the Interior) at, its Morgantown., W. Va., station, operating under a cooperative agreement with West Virginia University, is conducting research and development work on the problem of producing synthesis gas from coal. An important part of this work is the study of the gas purification necessary to meet the rigorous standards required to render the gas suitable for use in the Fischer-Tropsch synthesis of liquid fuels. One of the most detrimental impurities is sulfur in all forms, the maximum amount that can be tolerated being one-tenth of a grain per hundred cubic feet. Concentrations as low as this require the use of precise analytical methods to evaluate the performance of processes used for removing sulfur. At the same time the analytical methods should be rapid in order to reveal the failure of purification before damage to the expensive synthesis catalyst results. Although sulfur in unpurified gas is generally present as hydrogen sulfide and as organic sulfur compounds, the latter may be converted to hydrogen sulfide for analytical purposes. Thus a suitable method for the determination of traces of hydrogen sulfide may also be used for the determination of organic sulfur.

Jan 1, 1949

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr, Fieldner and Davis, and others, has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M. standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting the results in those types of fuel which give erroneous results due to mechanical losses. This mechanical loss is usually designated as "sparking." There are two kinds of sparks or incandescent particles which may appear: particles of soot from partially condensed carbon from the burning gases, and unburned particles of the material itself which escape. The first type does not affect the accuracy of the volatile matter results, and is therefore negligible. The second type, however, causes appreciable loss and results in showing higher volatile percentages than actually exist.

Jan 1, 1932

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

By Forrest T. Moyer

THE injury data and experience in this bulletin are presented in three general sections. The first section contains general and detailed data relating to 1948 injury experience in bituminous-coal and Pennsylvania anthracite mines, separately and combined into totals for all coal mines. The related employment, worktime, production, and productivity data are given in each breakdown of the statistical data. Tables 1 through 22 constitute a subsection and present statistics on number of injuries, frequency and severity rates, average severity, detailed and major causes of injuries, injury records of the coal-producing States, distribution of injuries by part of body, and distribution of injuries by days of disability. Tables 23 through 45, the second subsection, present injury experience in bituminous-coal mines by various selected factors of physical or operating conditions that ma contribute to the occurrence of injuries. The degree of mechanical loading, productivity, size of mine by number of men working and by tonnage mined, thickness of bed, length of shift, number of shifts, type of cap lamps, rating of mine as gassy or nongassy, type of ventilation, and combinations of these factors influencing mine safety are presented in this group of tables. Similar data on Pennsylvania anthracite mines are listed in tables 46 through 63, which comprise the third subsection. The second section of the report contains the generalized annual injury records of bituminous-coal, Pennsylvania anthracite, and all coal mines from the earliest available data through 1948. Tables 64 through 97 list the number of fatal and nonfatal injuries, injury rates, and causes of injuries on an industry basis, the long-term injury records of each coal-producing State, and the related employment, worktime, and production data.

Jan 1, 1952

By John R. Bartels

This report discusses an improved method for rerailing underground railcars devised in a joint effort by the Bureau of Mines and Hoesch MFD. This improved method utilizes a lightweight hydraulic ram with hand-pump activation to move a bridge-mounted roller carriage in conjunction with steel-reinforced air-lift bags. This method provides a lightweight portable system in which only two workers are required to perform the mine car rerailing operation. Because of the very narrow confines in underground mines, use of overhead cranes and other surface rail techniques is not possible. This new system is designed for very low profile work, and provides the necessary lifting force from light- weight compressed-air bottles.

Jan 1, 1985

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By V. E. Homme

Low- and high-temperature reduction techniques were employed by the Bureau of Mines in study of conditions favorable to the formation of massive titanium crystals. '1,1,2 low-temperature method, feeding molten sodium to solidified titanium lower chloride-sodium chloride, produced higher quality and high quantity crystalline metal. The percentage of crystalline titanium was increased with increasing reactor diameter, melt depth, and titanium dichloride concentration. The high-temperature technique, feed molten sodium to melts above 8000 C, producing needle-type crystals of lower quality and with less consistent results than the low-temperature method. Layers of titanium foil, sponge, fine needles, wool, and crusts of sin-tered granules were formed during the earl, -art of the low-temperature reduction, and massive crystals were produced beneath this barrier in the latter part of the reduction. Crystalline titanium having an average hardness of Bhn 76 and representing 58 percent of the total titanium was obtained. Lamellar crystals up to 1 1/2 inches long with a hardness as low as Bhn 54 were also produced. A second-stage reduction for reclaiming titanium from offgrade sponge is described. Titanium produced by this method was comparable in quality to that from sodium reduction of titanium tetrachloride.

Jan 1, 1966

By Stephen D. Hill

The Bureau of Mines devised and constructed a modified Knudsen effusion apparatus, permitting a constant measure of the weight of effusing vapor, to determine the equilibrium vapor pressure of metal halides at temperatures up to 1,200° K and over the pressure range 10-5 to 10-2 torr. The reliability of the apparatus was established by determining the vapor pressure of potassium chloride. After correcting for partial dimerization of the vapor, data obtained on solid KCl between 750° and 950° K can be expressed by the following equation:

Jan 1, 1966

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963