Search Documents

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 1/8-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By W. A. Selvig

[THE BUREAU OF MINES receives many requests for information regarding the low-temperature carbonization properties of American coals. This report presents in collected form the results of Fischer-Schrader bench-scale, low-temperature carbonization assays at 500° C. made by the Chemistry and Physics Section at the Pittsburgh station of the Bureau of Mines. Most of the assays were made of coals tested in connection with a survey of gas and coke-making properties of American coals,4 which was started in 1928 by the Bureau in cooperation with the American Gas Association. Other coals were assayed in connection with miscellaneous investigations. Since 1930 about 400 samples of coal were assayed from nearly every coal-producing State, Alaska, and British Columbia, Canada. The results of the tests on about two-thirds of the coals are scattered through more than 50 separate publications. This paper summarizes the data in the published reports as well as all unpublished data obtained to January 1, 1956. The report also includes a detailed description of the procedure used in making the assay.]

Jan 1, 1957

By J. E. Murphy

The high-purity thorium metal was prepared by the Bureau of Mines from electrolytically produced thorium alloys. The thorium-chromium and thorium-manganese alloys were separated into the component elements by vacuum distillation. Chromium and manganese impurities remaining in the thorium metal after distillation at 1,850° C were <0.005 weight-percent. Removal of volatile impurities such as aluminum, calcium, magnesium, and lead was also accomplished.

Jan 1, 1969

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 6, 1974

By Manuel Gomez

A computerized moving average technique was developed to interpolate coal seam characteristics between sample points. The interpolative method coupled with multivariate regression analysis and simulation procedures was used to forecast coal properties not readily obtained from an analysis of drill core samples. Coal property forecasts were of two kinds: (1) specific mine property forecasts that are suitable for mine product control and yield a good approximation of the local variation along both the vertical and horizontal axes of the seam, and (2) regional estimates where much of the local seam variation is smoothed out, but the general trends are maintained. Forecasts of the volatile matter, ash, total sulfur, and the heating value for part of the Pittsburgh seam located in Ohio, Pennsylvania, and West Virginia were in good agreement with independent evaluation data. Spatial configuration for preparation characteristics, particularly, the effect of crushing on sulfur release, low-and high-temperature carbonization properties, the Hardgrove grindability index, the coal hardness index, gasification variables, and hydrogenation factors were constructed for the same area of the Pittsburgh seam. These forecasts may be developed from drill core data collected in the exploration phase of mining. The results, which may take the form of a series of maps, are useful to mining, chemical, and combustion engineers, to economists and mine managers, as well as to coal users for mine design, economic analyses, energy forecasts, utilization studies, mine product control, and environmental control and programming.

Jan 1, 1974

By Kenneth B. Higbie

PRESIDENT LYNDON B. JOHNSON announced at midyear that the test flight of the A-It plane, the world&apos;s first super-sonic aircraft capable of flying 2,000 miles per hour, was made possible by "the mastery of the metallurgy &apos;and fabrication of titanium." Not all of the contributions made by the mineral industry in 1964 were acknowledged so widely. Yet the contributions were significant as the search continued for new and improved methods for providing metals and mineral products to meet the ever-expanding requirements of the world economy. This chapter reviews only a few of the metallurgical developments that resulted from U.S. and foreign research efforts. MINERAL BENEFICIATION Up-to-date theory &apos;and practice in the mineral ,Processing field in 1963 involved subjects such as autogenous grinding, high-intensity magnetic separation, and mill control by computers. These subjects were fully discussed at the Seventh International Minerals Processing Congress held in New York City during September.

Jan 1, 1965

By F. D. DeVaney

In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley Experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Linn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Joseph and Kinney in writing about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say: "***It has been estimated that 26 to 35 million tons of ore contain 5 to 35 per cent of manganese, and the total domestic tonnage is from 75 to 48 million tons. The mean of these values is 30.5 million and 42 million tons, so it is seen that about 75 per cent of the reserves are in Minnesota." The manganese-bearing ores of the Cuyuna district maybe roughly grouped into two classes. The most abundant ore is of the low-silica, low-manganese, and high-phosphorus type called brown are. The other type is the so-called black ore, which is characterized by a higher manganese and silica content and by a lowe phosphorus analysis than the brown ore. As a general rule the brown ore carries less than 10 per cent of manganese while the black ore contains about 15 per cent and sometimes as high as 22 per cent of manganese.

Jan 1, 1930

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By V. E. Homme

This report describes methods of using sodium for reducing titanic chloride, developed as part of Bureau of Mines activities at Boulder City, Nev., to improve the extractive metallurgy of titanium. Theoretical indications pertaining to the major chemical reactions and possible side reactions of the process are compared with experimental observations. Low-temperature reduction equipment is described, in which titanic chloride was reduced with sodium at temperatures between 97.5° C., the melting point of sodium, and 200° C. Techniques employed in making reductions in ball-mill and high-surface sodium reactors are given.

Jan 1, 1958

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By James C. Church

The Bureau of Mines devised and demonstrated a portable linear cutting tester that directly measures and records the in situ cutting forces required of continuous-mining machine picks to it coal in underground mines. It requires only two operators to transport and operate the tester, which can be assembled and operated through a complete test cycle within a single mine work shift. This report reviews the factors considered in the design and development of the tester and the results of its system verification testing at coal mine sites.

Jan 1, 1985

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

Table 1.-Salient aluminum statistics (Thousand short tons and thousand dollars) [ ]

Jan 1, 1967

By Ivan F. Avery

OUTPUT of carbon black in 1959 increased in all producing States except New Mexico. The national increase was 20 percent. Domestic sales and exports increased 22 percent and 16 percent, respectively, resulting in a 21 percent gain in sales. Sales to the rubber industry, which purchased 95 percent of the domestic output of carbon black, increased 23 percent. Sales to all other major consumers also increased. Stocks decreased 82 million pounds during the year. [ ]

Jan 1, 1960

By Frank D. Lamb

Four samples of manganese-bearing material from the Aroostook County, Maine, deposits were tested at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., to determine their amenability to beneficiation by ore-dressing methods. The samples represented material from the Maple Mountain-Hovey Mountain deposit, the Dudley farm, and the Burnham farm and contained 11 to 14 percent manganese. None of the tests produced appreciably enriched concentrates suitable for further treatment for the production of ferromanganese. The intimate association of the manganese minerals with iron and siliceous minerals requires extremely fine grinding to liberate the manganese minerals in these ores and prevents efficient concentration by physical means.

Jan 1, 1953

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau&apos;s trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle&apos;s pole is removed or the vehicle leaves the section.

Jan 1, 1978

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989