Search Documents

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in nongassy noncoal mines and tunnels. This revised and supplemented listing supersedes an earlier publication2 released in 1963. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and outlined in the Bureau's permissible schedules before the Bureau approves it for safe use in mines.

Jan 1, 1968

By R. V. Subramanian

This project financed by the Bureau of Mines investigated the use of polymers to achieve rock bonding and reinforce coal mine structures for better or permanent ground support. Support was achieved by pumping the polymers into the rock interstices to bond the mass together for increased structural competence. Holes were drilled in the mine roof, after which the polymers were injected at about 100 psi to permeate the cracks. Initial laboratory work indicated that of all the resin systems tested, the epoxy resins could most likely be modified to be suitable for rock injection. This was confirmed when several potentially suitable resin systems underwent intensive evaluation. In a series of three field tests, two conducted in a copper mine with coal mine-type shale and the third in a coal mine, it was shown that the polymers penetrated cracks less than 0.005 inch wide. The fast-setting epoxy systems, cured out in thin films under mine conditions, produced a bond exceeding the strength of the uncracked virgin rock.

Jan 1, 1974

By William P. Diamond

Ventilation has long been the primary means of controlling methane emissions in underground coal mines. However, as mining has progressed into gassier areas of U.S. coal basins, supplemental means of methane control have become of interest, if not a necessity, for continued safe and productive mining operations. This paper describes the history and technology of methane drainage in the United States and other countries. The methane drainage technology developed in European countries is a valuable resource since their longer history of mining has already forced mine operators to deal with methane emission problems only now being experienced in the United States. Methods for assessing the need for methane drainage and the data required for planning and implementing an appropriate system are reviewed. The effectiveness of the various technologies for reducing methane emissions underground and/or the in-place gas content of individual coalbeds is illustrated with case studies. In addition to the safety and productivity gains to be realized from methane drainage systems, the potential for commercialization of coalbed methane is discussed.

Jan 1, 1994

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

By Edward G. Cunney

Track in underground bituminous coal mines was investigated, and technology was taken from other industries in order to obtain information on conditions that impair the safety and efficiency of the track and to develop guidelines and useful information on the construction, inspection and maintenance of mine track. Volume 1 contains information on the investigations, observed track conditions, useful technology from railroads and other industries, derivations of track condition descriptors and recommended limits, conclusions, and recommendations. Volume 2, Guidelines, contains recommended standards and practices for mine track. It includes the relation of track conditions to safe speeds; descriptions and limits for measurable track features such as gage; descriptions of conditions for track components that are normally not measurable, such as subbase soils; construction requirements and techniques, inspection requirements and methods; and methods for managing and performing track maintenance work. As a research product, it does not repeat the summary or derivations. Volume 3, Inspection Handbook, summarizes recommended standards and procedures from Volume 2 and provides related information for' ready reference by inspectors in the mines. As a research product to be used in mines, it does not repeat the summary, derivations or references.

Jan 1, 1977

By M. D. Aldridge

This document reports the results of a two-year research effort aimed at improving communication systems used in coal mines. This work was conducted under a program whose original goal not only involved the development of practical and effective electronic systems for operational communications, but also for monitoring, at a central location, remote instruments at key positions in a mine. About half way through the originally proposed three year effort, the program was redirected to phase out the communication effort at the end of two years and to concentrate the program" resources on the investigation of new monitoring system concepts developed by this research. Thus, the work reported here is incomplete relative to the originally pro- posed program. However, the work was carried to the point of providing sufficient evidence to aid in the comparison of certain new communication concepts. For the concepts chosen for this study, the work was stopped short of hardware development and field testing, Several reports in the form of Master's theses and a Doctoral Dissertation have resulted from this research. They each report in considerable detail the results of several individual" contributions to this program. In preparing this report, an attempt has been made to provide a complete description of the significant results but with- out burdening the reader with the minute details. These more detailed reports are referenced heavily for the convenience of those interested. PRESENT COMMUNICATION METHODS Two types of communication systems are presently used In coal mines. They are: 1, Various forms of telephone systems, and 2. Carrier current radio systems using the trolley line as the interconnection circuit. Carrier current radio is used almost exclusively for control of rail trafflc by the dispatcher. Almost all other communication uses the telephone system, Telephone lines generally extend to areas where trolley lines are not present such as the outside offices and warehouse. Therefore the telephone system provides the primary means of voice communication. Telephones - Telephone systems employed in American coal mines fall into three categories. 1. Paging type telephone systems - these systems have individual stations which use battery powered transistor audio amplifiers to boost signal levels for normal communication. When in the page mode,

By Stephenson. E. L.

"INTRODUCTION In the spring of 1942 a series of magnetometer surveys on deposits of black sand underlying Pleistocene raised marine terraces along the coast of southwestern Oregon was nada by the Division of Geophysical Exploration of the Federal Bureau of Mines in cooperation with the Oregon Department of Geology and Mineral Industries. A few preliminary tests had been made in the same area in May 1940 and December 1941.The sands contain fine gold and metals of the platinum group, and, beginning in 1852, extensive, but spasmodic mining and exploration have been done for these precious metals. There are many old placer, mines and prospects, although for the most part the yield of the metals has been small. The sands also contain other minerals of potential value, including ilmenite, magnetite, garnet, zircon, and particularly chromite, and the wartime demand for domestic chromite resulted in extensive testing and development of the known deposits. The purpose of the magnetometer surveys was to determine the efficacy of, magnetic methods in tracing and outlining these known deposits and in prospecting for new ones. The field work was done between March 17 and May 29, 1942, by the author assisted by W.W. Paulsen of the Oregon Department of Geology and Mineral Industries."

Jun 1, 1945

By Mark Sheppard

[Considerable research work hi been done on secondary crushing and coarse and fine grinding, and the literature on the general subject of Crushing contains many references to the work of investigators on the laws governing end the factors entering into the economical production of fine materials. However, little information on primary crushing in available The literature deals mainly with problems and practices in ore dressing, end in this field the engineer or investigator is concerned largely with the production of fine material and the unlocking of minerals in the ore. Under such conditions close control of screen sizes of primary-crusher products is a secondary consideration and has received very little attention.]

Jan 1, 1938

By Donald Giroux

This report documents the design, fabrication, testing, and coal mine demonstration of a hopper-feeder-bolter during a four-phase program for the U.S. Bureau of Mines. The machine was designed to increase productivity and safety in under-ground room-and-pillar mining. It performed well as a hopper-feeder for continuous haulage during a coal mine demonstration. Testing in a simulated mine showed that the machine also has good roof bolting capability.

Jan 1, 1987

By Robert A. McColly

This Bureau of Mines report compares the availability of federally owned minerals in Arizona with lands considered favorable for discovery of mineral resources, to deter-mine the extent to which Federal mineral lands in such areas have been withdrawn by legal action or restricted by management practice. Of particular concern are restraints on Federal lands in areas identified as highly favorable for occurrences of valuable mineral deposits. Excluding Indian lands held in trust by the Federal Government, about 32 million acres, 44%, of Arizona's mineral estate is federally owned. This total includes lands with partial Federal mineral ownership. Approximately 16.5 million acres, or 52% of these lands, are available for location or lease. This includes 496,000 acres, 62%, of the lands highly favorable, and 2.6 million acres, 57%, of the lands moderately favorable for locatable minerals in Arizona. All other Federal mineral lands are either withdrawn or restricted, reflecting a wide range of purpose, authority, and impacts on mineral exploration and development.

Jan 1, 1987

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977

By H. S. Auvil, L. D. Schmidt, H. G. Graham

"Several studies on the bulk density of coals prepared for byproduct-oven use were undertaken during the war by the Bureau of lanes in cooperation with the Office of the Solid Fuels Administrator and with the advice of the Coke Production Committee. The primary purpose of these studies was either to produce more uniform coke or to increase the throughput of existing facilities or both; the goal was increased Production of steel for war. As these studies were made, detailed reports were sent to the individual companies with whom the Bureau cooperated; also two reports,5/6/on the general subject of bulk-density control were published. In the course of the work, data were gathered that now prove of value in judging the merit of carious methods of testing bulk density and the limits of application of each method in byproduct-oven operations.Since the cessation of hostilities, the .Bureau section (Coke Production Survey Section) that conducted this work has been liquidated, but it was felt advisable to prepare a report on the accumulated experience so that it would be in a form available for the use of the industry and also as a base for any further research on the control of fluctuating bulk densities in coke ovens.It is hoped that the data and experiences recorded herein will be of material assistance to the many who have had difficulty in obtaining reproducible results in bulk-density testing. Since the data were gathered in the course of extending aid to individual plants in minimizing the deleterious effects of fluctuations in bulk density of oven charges on the quality and quantity of coke produced, certain desirable phases of an over-all investigation were not covered. However, on certain of these phases qualitative indications are available and the policy followed herein is that suggested by the American Society for Testing Materials Manual on Presentation of Data7/ that lacking quantitative information, relevant material should be included even though it ""may be qualitative in character, some may even be vague."""

May 1, 1946

By Milton B. Hall

This report discusses in detail laboratory and pilot-plant tests conducted from January 1951 until January 1955 at the Northwest Electrodevelopment Experiment Station of the Bureau of Mines, Albany, Oreg., on defluorination and recovery of evolved fluorine from phosphate rock. Results of use tests of defluorinated phosphate rock by cooperating agricultural colleges and the United States Department of Agriculture are also included. In 1954 the consumption of fluorspar, the only domestic fluorine-bearing mineral of commercial importance, was approximately 478,000 short tons; 245,000 tons was from domestic mines. The production of marketable phosphate rock in the same period was about 13,800,000 long tons. Of this total amount, approximately 15 percent was produced in the West. From the viewpoint of conservation and utilization of fluorine as a natural resource, it is interesting to note that the total estimated quantity of fluorine in domestically produced phosphate rock is more than double that present in domestically mined fluorspar.

Jan 1, 1958

By A. L. Service

Idaho has nearly 6 billion tons of potential sources of phosphorite, 10 to 31 percent P2O5' above and within 100 feet below entry level, the largest potential of any State in the United States. In 1963 Idaho ranked third after Florida and Tennessee in total mine and marketable production of phosphate rock; Montana ranked fourth. This report describes phosphate deposits, mines, and prospects in 10 districts covering most of the Idaho phosphate field. All mine production of phosphate rock in Idaho comes from surface mines and is processed to phosphate fertilizers, phosphoric acid, and elemental phosphorus. Producing districts are Fort Hall (Gay mine), Trail Creek (Conda and Ballard mines), and Crow Creek (Georgetown Canyon mine). FMC Corp. and J. R. Simplot Co. at Pocatello have the largest elemental phosphorus and fertilizer production facilities, respectively, in the State, followed by Monsanto Co. and El Paso Natural Gas Products Co. (formerly Central Farmers Fertilizer Co.). The only other major phosphate processing plant in the State is the phosphoric acid and phosphate fertilizer complex at Kellogg operated by the Bunker Hill Co. In 1963 a plant was constructed and put on line at Monsanto, Idaho, to recover vanadium from ferrophosphorus produced by electric furnace operations in the area. El Paso Natural Gas Products Co. completed construction of a fertilizer and phosphoric acid plant near Conda in 1965. There is a small fertilizer plant producing phosphate fertilizers for local consumption in Soda Springs.

Jan 1, 1966

By Staff

This U.S. Bureau of Mines publication presents the results of investigations into the fire and explosion hazards of oil shale rocks and dust. Three areas have been examined: the explosibility and ignitability of oil shale dust clouds, the fire hazards of oil shale dust layers on hot surfaces, and the ignitability and extinguishment of oil shale rubble piles.

Jan 1, 1989

By N. F. Le] [Jaune

[ ]

Jan 1, 1923

By Donald P. Tuchman, Robert P. Vinson, Linda J. McWilliams, Steven E. Mischler, Jon C. Volkwein

A personal dust monitor (PDM) was developed to measure respirable coal mine dust mass to provide accurate exposure data at the end of a work shift. Additionally, the new monitor continuously displays near-real-time dust exposure data during the shift. The PDM uses a tapered-element oscillating microbalance to measure the mass of dust deposited on a filter and continually displays the cumulative exposure concentration data. The accuracy and precision of the instrument was determined by comparison to gravimetric filter samplers in the laboratory and in four mines. Laboratory results with different coal types and size distributions showed that there is a 95% confidence that the individual PDM measurements were within ±25% of the reference measurements. Mine test results indicate that data taken with adjacent PDM and reference samplers are indistinguishable. The technology proved durable enough to successfully measure 108 shifts of data out of 115 attempts in the mines. Under these specific test conditions, the PDM demonstrated that it was convenient to wear, robust, provided accurate data, provided timely data that could be used to prevent overexposure, and was easy to use.

Jan 1, 2004

By Madan M. Singh

This report presents the results of an investigation of inclined roof bolts, anchored over pillars, in room-and-pillar coal mines susceptible to shear failures of the roof. Although the field data do not support this contention, it is believed on the basis of analyses and other work that inclined roof bolts do offer potential under some circumstances.

Jan 1, 1978

By R. G. Warncke, J. H. East, D. Harrington

The mining industry of the United States has long been severely criti- cized because of its high rate of accident occurrence, not only as compared with other industries of the United States but also with the mining industries of other countries, particularly Europe. Statistics, often not strictly com- parable, indicate that the accident-frequency rate in all mining is currently about three times and the accident-severity rate is about seven times as great as the average for general industrial work in the United States. These fig- ures are by no means comforting to humanitarian mining men, irrespective of their status in the industry, and they constitute a challenge that certainly cannot continue to be ignored much longer. The picture becomes much darker when the above statistics are augmented with data indicating that on an exposure basis our mines (more particularly our coal mines) have accident rates two, three, or even more times as great as more or less similar mines in Europe, particularly England, Wales, Belgium, France, and Germany. The sting is alleviated to some extent by the knowledge that our coal mines produce about 4 to 5 times as much coal per man day as is produced in at least some European mines. However, all of these foreign acci- dent statistics should be analyzed carefully before we become very much con- cerned about them, because they are not strictly comparable, for several reasons, not the least of which is the fact that foreign methods of compiling or recording accident statistics often differ materially from ours. Moreover, foreign mining and other conditions are definitely dissimilar to ours in many phases, and numerous other factors affect the comparability of foreign mine- accident statistics with those of the United States. Unquestionably, it should also be taken into consideration that the accident rate of the 140,000,000 or more constituting the populace of the United States as a whole is much higher than that of any other major country in the world and is two, three, or more times the rate of the European countries that have more favor- able mine-accident rates than those of the United States (table 1). Moreover, it is significant that the mine-accident-severity rate of British mines is about six times the average accident-severity rate of the major industries of the British Isles, or but little more favorable than the comparable figures in the United States; namely, that mining has an accident severity rate about seven times the average of about 30 of the major industries of this country.

Apr 1, 1949

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932