Search Documents

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By William H. Pomroy

The Bureau of Mines, through a 4-year program of combined in-house and contract research, has developed the necessary hardware and software technology to provide rugged, reliable automatic fire protection for surface mining mobile equipment. One element of this program was a continuing effort to help foster rapid mining industry acceptance of the technology by keeping end user costs reasonable. This report is an analysis of the economic impact of surface mining mobile equipment fires and the cost benefit of utilizing automatic fire protection systems to abate these losses.

Jan 1, 1982

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

By M. J. Ferrante

The Bureau of Mines investigated the applicability of the freeze-drying technique for preparing dispersion-strengthened tungsten powders suitable for conversion by powder metallurgy into materials which might have improved high-temperature strength. Extruded rods from compacts of tungsten-5 vol pct thoria had at 1,650° C a tensile strength of 30,300 psi and a 10-hour stress-rupture strength of 12,700 psi, These are slightly below those measured for swaged rods of commercial tungsten-3.7 vol pct thoria. Only those tungsten-thoria dispersions containing a stoichiometric deficiency of oxygen yielded a significant strengthening effect. A low-melting eutectic formed in extruded tungsten dispersions containing either zirconia or yttria, which caused a lowering of the tensile strengths. These tensile strengths were only slightly higher than strengths of elemental tungsten made from commercial powder having a particle size of 2.4 microns (Fisher subsieve). Sheet made from this commercial tungsten had a slightly higher tensile strength than tungsten made by freeze drying, but the freeze-dried tungsten sheet had a lower recrystallization temperature, a lower ductile-to-brittle transition temperature, and a higher purity.

Jan 1, 1971

By M. John Brodie

This report reviews the regulatory environment as it pertains to waste rock management and disposal from mining operations, excluding coal and placer gold operations, in the \irate of Alaska. It is based on the EPA's staff position on an effective program to regulate mining waste as presented in the May, 1990 Strawman II document. The unique conditions which occur in pans of the state, including a fragile environment, high seismicity and permafrost, are identified. The special waste management practices which are necessitated by these conditions are delineated. The report provides a detailed outline of the current technologies that are suitable for designing, constructing, operating and closing a waste rock facility to meet environmental protection objectives. Cost implications to the mining industry of potential regulatory actions, such as the degree of groundwater protection, are examined.

Jan 1, 1992

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

Electrical trailing cable used to power coal mining machinery is frequently damaged in usage because of tensile strain or crushing effect of mining machines running over the cable. One of the repair problems is finding the exact location of a short or open in this cable so it may be spliced or otherwise repaired. The U.S. Bureau of Mines and FMC corporation signed Contract No. H0 122011 in August, 1971, to develop instrumentation for finding faults in coal mine trailing cable. This report describes performance of several existing instruments as trailing cable fault locators and also construction details and performance records of several cable fault location instruments that FMC designed, built and tested as part of this project.

Jan 1, 1973

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979

By D. E. Kirby

In line with the Bureau of Mines' goal of providing technology to maintain a supply of minerals adequate to meet national economic and strategic needs, a method for recovering chromite from lateritic materials was investigated. Laterites are a large resource of Ni, Co, and Cr, critical metals of which the United States has insufficient domestic sources. A roast-leach method was developed by the Bureau to extract nickel and cobalt from domestic laterites. A concurrent effort was made to recover chromium from either unprocessed laterites or the leach residues. This report characterizes laterites and laterite leach residues. It describes a chromite recovery procedure using conventional industrial beneficiation equipment for sizing, low-intensity magnetic separation, and gravity concentration. Concentrates containing 20.0 to 22.4 pct Cr (29.0 to 32.7 pct Cr203) and with a 1.6:1 to 1.9:1 Cr-Fe ratio were recovered from laterites and residues containing 1.3 to 2.5 pct Cr with recoveries exceeding 50 pct. Because of their low grade and fine size, these concentrates would be suitable for preparing chromium chemicals. The direct beneficiation of laterites for chromite recovery resulted in the minerals containing nickel and cobalt concentrating in slime products. No iron oxide coproducts of acceptable grade were recovered from either laterites or residues.

Jan 1, 1982

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979