Search Documents

By M V. Van Bers, A L. McAnuff, A Curic

During the Summer of 1997, rock excavation was carried out for construction of the Centre Block Underground Services building (CBUS) abutting the most historically significant structural complex in Canada, the Parliament Buildings in Ottawa. Controlled blasting was required for the removal of 25,000 cubic metres of limestone bedrock within the ten week time window of Parliamentary recess. A test blast program carried out in 1996 had established that close blasting was viable even within the very restrictive limits considered necessary to preserve the structural and cosmetic integrity of these historic structures. In total 300 blasting operations were required to complete the excavation, including the 20 test blasts conducted in 1996. Based on attenuation characteristics established for the site during the trial blast phase, the blasting contractor proposed excavating the CBUS site in three zones. Each zone contained differing drill patterns, depths and explosive loads. Vibration intensities, air concussion levels and displacements across representative existing cracks were measured and recorded at numerous observation points within and around the Centre Block and the Library of Parliament, as well as on the grounds of the Parliamentary Precinct. The blasting portion of the excavation was completed within budget in less than eight weeks, well within the tune window available. Comparison of very extensive pre and post-blast condition surveys revealed no damage to the existing structures on Parliament Hill as a result of these operations.

Jan 1, 1999

By CVB Cunningham

"The Kuz-Ram model as originally proposed included an error in assuming that the mean fragmentsize predicted by Kuznetsov’s equation was actually the 50% passing size. In 2003 Spathis began discussions on this issue and recommended correcting the equation. The correction produced more fines in the predicted fragmentation, which had been a criticism of some users of the original model. Ouchterlony subsequently showed that the error had, if anything been beneficial, and that the Swebrec function adequately covered the fines. This author shows that the Spathis correction does not assist the fines correction in examples examined, but tends to underestimate coarser fractions. An intrinsic problem of communication between academics and engineers is a root of misunderstanding on both sides, and requires patience by both parties to enable value to arise."

Jan 1, 2016

By M. Y. Wong

Electronic detonators have been used on a trial basis for over a decade, and found more recent application in production blasting as well. The relative merits of these detonators and their applicability are outlined through examples from actual blasting operations. They offer unprecedented flexibility in the design of mass blasts and in control of vibration and blast-induced damage. However, the drive towards replacing the pyrotechnic detonators by electronic ones in general could prove to be counter productive without a re-examination of prevailing blasting practices. In fact, such an approach tends to blur the tremendous potential of the electronic detonators in redefining many standard blast designs and practices.

Jan 1, 2004

By Jesus Pascual, Benjamin Cebrian

A new Convention Center is going to be built in the millenary city of Toledo, right in the old city limits. The workings will need to excavate some 80.000 cubic meters of granite, which has, a trench-like structure already blasted for the construction (60 years ago) of a parking lot and a shopping area. Surrounding this trench, some few feet away, there are structures and buildings from the 16th century and remainings from previous times that need to be preserved from any damage caused by blasting. Because of this, a vibration analysis was designed according to the special characteristics of this work. Structures to monitor were located at several levels. It considered three different directions of study in order to evaluate the impact of vibrations of the structures located at three different heights of the granite trench. On top, the historical convent of Santa Fe, with some remaining from the 8th century (Muslim domination of the Iberian Peninsula), on the bottom, the Justice Hall of Toledo with 16th century walls, and, in the middle, a wall and a tower from times of the king Phillip II (16th century, the time of the Spanish Empire).

Jan 1, 2004

By Richard Turnbull, James Purssey

"The Northconnex Project is a twin nine kilometre tunnel in Sydney, Australia, linking the M1 PacificMotorway at Wahroonga to the Hills M2 Motorway at West Pennant Hills. Access to the tunnels will befrom portals at either end and from three vertical shafts spaced along the length of the motorway. These shafts will provide access for equipment, plant and personnel, removal of spoil during construction,ventilation, and emergency egress points during tunnel operation. The three shafts have a 12 m x 16 m (39 ft – 53 ft) cross sectional area and depths ranging from 45 m to 91 m (148 ft – 299 ft). The vibration limit for the shaft blasting was set at 10 mm/s ppv, with residential properties as close as 31 m (102 ft) and the existing M1 motorway 80 m (262 ft) away. The traffic volume for the M1 is 80,000 vehicles per day and Northconnex will provide an additional 100,000 vehicle capacity. "

Jan 1, 2017

By Joseph Indeck, Seokbin Lim, Andrew Thompson

In the design of explosively driven penetration devices, understanding the impact conditions between the explosively propelled penetrator and the target is one of the most important steps in optimizing the performance of the device. These impact conditions are especially prevalent when a shaped charge jet impacts concrete, which is not an ideal target material. The specific impact conditions, including but not limited to the impact angle and jet properties, create a great deal of variability that affects the performance and penetration of the shaped charge. The large amount of impurities and voids in concrete, along with its heterogeneous nature and the general strength characteristics, make concrete a non-ideal material for shaped charge jet penetration. These material characteristics lead to a highly non-linear deformation behavior of the concrete target during a hyper-velocity impact.

Jan 1, 2011

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Alastair Torrance, Gary Cavanough

Approximately 1.5 million tonnes of ammonium nitrate are transported annually across Queensland, Australia—equivalent to nearly 100 truckloads per day. This is in the form of both AN prill and ammonium nitrate based emulsions (ANE). In a recent incident, a collision involving an ANE tanker resulted in a detonation that caused extensive blast-related damage and led to the closure of a major highway. Had this event occurred within a populated area, the consequences would have been catastrophic. For over a century, investigations into the causes of such spontaneous detonations have been inconclusive. A recently completed industry supported research project has made a pivotal discovery: a surface reaction mechanism leading to hydrogen generation has been identified as a precursor to detonation. If sufficient hydrogen accumulates and subsequently ignites, it can release enough energy to initiate the detonation of bulk ammonium nitrate and ANE. Controlled experiments conducted during the project successfully demonstrated hydrogen-driven detonation events. Previous work by Proulx and Scovira, presented at the 2000 ISEE Conference, described spontaneous detonations in hot, reactive ground and the mitigating effects of buffered emulsions and ANFO. Building upon their observations, this study reproduces similar incidents under laboratory conditions, confirming that hydrogen generation also results from reactive ground interactions. Importantly, the findings challenge traditional assumptions, demonstrating that ammonium nitrate and ANE detonation in reactive environments does not require an ignition temperature threshold, confinement, or a classical chemical decomposition pathway.

Jan 26, 2026

By Alain Blanchier, Anne Charline Sauvage

Rock mass variations have a huge influence on explosives efficiency and on blasting results. Numerous blasting improvements could be gained by taking into account rock mass and its variations. However, extracted rock mass is generally considered as statistically homogenous. The development of a panel of pre-blast survey procedures that every blaster can use, consists in the realization of a process integrated into every day work: for example as well as toe burden or blast hole depth, discontinuities spacing or the weathering expanse have to enter in rule book, if it provides blasting efficiency and security improvements.

Jan 1, 2004

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Les Willan, Chris Batten, Matt Sparkes

In late 2008 Xstrata Newlands Coal Mine in Central Queensland and Orica Mining Services engaged in discussion to investigate methodologies to change their current mining practices and overcome the issues in the mining of steeply dipping coal seams, the associated coal loss risk and to assist in improving mining productivity. A strategy was developed and it was determined that through-seam blasting was essential to the success of winning the coal from the Wollombi Pit at Newlands.

Jan 1, 2010

By Cary Moffat, John Kita, Rick Walker

The Lac des Iles Mine, in an isolated area of NorthwesternOntario is a relatively new open pit platinum and palladium mine. They were encountering problems with the equipment and production scheduling when ramping down to begin production on the subsequent benches. A co-operative effort between Lac des Iles Mine operation people, ICI Explosives, and the mines drilling and blasting contractor - Consbec Inc., resulted in a decision being made to use full depth sinking cuts to provide access to the next bench.

Jan 1, 1996

By Jeff Senules, Oana Meins, Catherine Aimone-Martin, Scott Lanker, Brent Meins

Global wall strains from 4 to 77 micro-strains were measured at three structures adjacent to a highly-confined Florida quarry blast when PPV amplitudes ranged up to 6.05 in/s. Increasing the peak zero-crossing frequencies with carefully control delay timing helped to lower ground displacements affecting wall strains.

Feb 1, 2020

By Andrew Moore

It has long been common practice to conduct drilling and blasting operations at surface quarries in the Midwest in close proximity to near-vertical highwalls. The main reasons for such an approach, and the limited use of adequate safety controls, can be associated with higher costs, operational constraints, lithological requirements, property boundary restrictions, inadequate quarry planning, or a lack of understanding of highwall risks. Working in proximity to highwalls, without effective controls, exposes personnel and equipment to increased risk of incidents. In recent history, there have been isolated incidents involving equipment damage, or personnel injury/fatality around the United States. However, the Midwest market has largely escaped the effects of such incidents, even though the exposure rate is high. Awareness about this matter greatly increased on January 19th, 2021, when a significant incident occurred at a quarry near Green Bay, Wisconsin. As a crew was loading a typical blast near a highwall, a ground fall occurred, and multiple rock fragments struck a laborer working on the bench below. This individual sustained significant and life-altering injuries.

Feb 6, 2023

By Bruce R. Leland, Steven H. Smith, John D. Paulson

The USDA - Wildlife Services has been removing beaver dams with explosives for over 30 years. This paper will discuss the history of the explosives program, summarize how we've evolved, and highlight our work removing beaver dams in unique locations.

Feb 1, 2020

By Stephen Mansfield, Saran Sankar

The Sentinel open pit copper mine, operated by First Quantum Minerals Ltd, is located in the North West province of Zambia. The Sentinel orebody is a sediment-hosted, structurally modified deposit in which mineralisation is contained in the phyllite formation, which occurs as a series of layered, continuous sheets having a northerly 20 to 30⁰ dip. The persistent nature of the geological structure can lead to the generation of large slabs when joints are relatively close together or very large blocks when joints are more widely spaced. With standard blasting methodologies, the challenging fragmentation most commonly occurs in the stemming zone and blast interfaces, reducing excavation rates and increasing the risk of crusher bridging events and reduced throughput. A generalised approach to increase powder factor would increase in drill and blast costs and would not be sufficient to target the specific cause of the challenging fragmentation. Implementing differential blast energy based on post blast requirements for different material type, such as ore and waste, and rock mass characteristics is not new in the mining industry. High-energy blasts for ore aim to produce finer materials, enhancing downstream processes such as crushing and grinding, while reducing power consumption and increasing throughput. Conversely, waste rock often requires less energy in order to deliver optimised fragmentation for loading and hauling efficiency. Identifying and applying optimum blast energy to specific material type and geological domains will not only ensure smoother and efficient operations throughout downstream processes, but will have a direct impact on overall profitability of the entire operation. This paper will describe the methods used to model and implement differential blasting across a range of material types in order to deliver the required blast outcomes for ore and waste and the impact on downstream processes and drill and blast unit cost.

Jan 21, 2025

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Alper Celtikci, Serdar Celik, Yucel Karakus

This paper presents bench blasting designs based on results of vibrations analysis on test shots organized in an open pit coal mine located near to Soma district at Manisa province in Turkey. There are some structures which can be adversely affected by blasting at the coal mine. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting at these structures by risk analysis based on ground vibration measurements. During this investigation, the data pairs of scaled distance and particle velocity obtained from the 36 event records belong to 9 test shots were statistically analyzed and a PPV prediction equation specific to this site with 95% prediction line were obtained. And also, this equation was used in the derivation of the practical blasting charts specific to this site as a practical way of predicting the peak particle velocity and maximum charge per delay for future blasting. A risk analysis was performed by using this equation. In the light of this analysis, preliminary blast design model was proposed to be used in this coal mine for overburden excavation.

Jan 1, 2012

By BruneJurgen F., Richard C. Gilmore, Matthew Schreiner, Ray Johnson

Explosive pockets of methane-air mixtures accumulate in underground coal mines and, when ignited, produce an air-blast wave that can disturb combustible coal dust on the floor, roof, and ribs. To prevent explosions, the coal dust must be continuously diluted through application of inert rock dust, usually powdered limestone. Application of powdered dust process creates a respiratory nuisance downwind, where miners cannot work until the dust settles. Rock dust suppliers have developed wet and foam applied products to reduce the nuisance and limit the interruption to mining during dust application. To test the effectiveness of these alternative dust products, researchers at the Colorado School of Mines (Mines) have constructed a full-scale explosion test drift located at the Mines Edgar Experimental Mine (Edgar) to study the dispersibility of different rock dust applications. This paper examines the use of Pentaerythritol tetranitrate (PETN) detonating cord to produce controlled air-blasts that simulate methane-air explosions. The air blasts are generated with curtains of detonating cord that produce shockwaves with wind speeds between 30 to 70 m/s (100 to 225 fps) depending on the length of 5.3 g/m (25 grain/ft) detonating cord used. These velocities represent the minimum air speeds required to trigger propagating coal dust explosions. Researchers have conducted 40 test blasts with various lengths of detonating cord. Results show the two primary waves and two reflected waves each decaying into airblast waves with overpressures of 14 to 27 kPa (2 to 4 psi). Pressures were recorded with commercial piezoelectric transducers and custom-built, bi-directional probes to record the total and dynamic pressures of the wind generated in the explosion. Researchers were able to generate consistent and repeatable wind speeds and air-blast durations sufficiently similar to a methane-air explosion to study the dispersibility of various rock dust products and application methods

Jan 1, 2019

By Adrian Moore, Bryan Goodwin, David Fales, David Lam

This paper describes the development of blasting protocols used to successfully create a 450m long blast fractured permeable trench in a basalt aquifer up to 20m thick, at a petrochemical facility in Australia, to enable the remediation of contaminated groundwater.

Jan 1, 2011