Search Documents

By Ye Yuan, Jaak Daemen, Shaguo Yuan

ABSTRACT: A 400m2 (480 yd2) heavily reinforced high-strength concrete slab 800mm (31 inch) thick had to be demolished. Underneath it was a 300mm (12 inch) thick underlying structure consisting of three layers: a cushion coat, a water barrier and a concrete layer that protected the water barrier. It was strongly desired by the owner that the underlying structure, especially the water barrier, remain undamaged during the blasting demolition of the reinforced concrete slab above it. This paper discusses the design of the demolition blast, problems encountered, and practical solutions to these problems. First, the impact caused by the charge explosion on the remaining structure was studied. In order to limit crack propagation in the concrete to the bottom of the concrete layer, the concrete isolation layer underneath the bottom of the slab to be demolished was left in place, to protect the water barrier and its protection layer. The effects of blasting vibrations on adjacent concrete were analyzed and precautions were proposed in the design. A safe blast design meeting the requirements to protect the water barrier below the slab was detailed. Rainwater collected and stored above the remaining underlying structure remained in place for two weeks, confirming that the design and blasting were successful.

Jan 1, 2010

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By K. Taylor

In surface coal mining, the performance of a shovel through blasted muck is one of the key performance indicators of the blast. Historically, performance has been measured qualitatively based on operator feedback or visuals of the muckpile. More complete shovel data, such as loading times and GPS location, is available from most fleet dispatch systems that are already in place at most truck and shovel operations. With some database and analysis skill, the drill and blast team can take advantage of this data to make targeted improvements to drill and blast designs. An area typically known to cause trouble for shovel operators at this operation are blast boundaries. Blast patterns with and without design changes along the boundaries were studied in this case study. The instantaneous loading times for each shovel pass were analyzed for 75 blasts across two subsequent benches with similar firing direction and shovel paths. The benches were split into three categories: Main body of pattern, boundary with design change, and boundary with no design change. The loading times from the main body of the patterns and where the design change was utilized in the boundary had similar prevalence of good loading times. However, boundary areas without the deign change had approximately 2% more prevalence of poor loading times compared to the main boundary of the pattern. Improving the dig rates through the boundaries up to the average loading time would result in approximately 280 hours taken off the total loading time for one bench. By quantifying the shovel’s performance by GPS location, the drill and blast team can decide how much of a design change is needed, can target precisely only the areas that require it and measure the impact of any changes made

Jan 1, 2024

By R. Ticona, J. Alarcon

In the continuous search to provide comprehensive solutions and identify opportunities to improve ore traceability, from the blastholes to mill feed, different ore traceability systems have been developed, which allow tracking the ore and associating its geometallurgical characterization of different sectors of interest from blasting to the processing plant, facilitating decision making and operational actions when detected during each stage of the plant. With the objective of improving the ore tracking from the mine to the processing plant in a Peruvian copper mine operation, the impact on the processing plant was evaluated in relation to blasting optimizations through a tracker system, relating the processes performance of the whole production chain with the geotechnical and geometallurgical properties ores in real time in the process plant: detecting when it was feed waste, high grade ore, low grade ore and ore with arsenic, among others. Unit and integral tests were carried out over a period of three months, with an implementation of tracker detection portals in the processing plant, which allowed to verify the proper communication of data and the web platform. The tests were focused on several blasts where the ore was in contact with waste and it were directly sent to the plant, with a classification by type of grade (high, medium, and low grade), type of material (ore-waste contour), this stage allowed to make operational adjustments in the field and in the mining operation. Finally, in the economic results, the special tests had 1000 trackers, obtaining for this project a sensitization of a cost benefit for the test stage, for the reduction of 50% of the waste material feed has crushed, with an estimated benefit of 1,987,646 USD.

Jan 1, 2024

By Mark Bosse

This is a paper demonstrating the use of a fixed wire and trolley system to deliver 2 or 5 lb cast primers (with 2 meter cap/fuse assemblies) deep into avalanche terrain. This avalanche terrain is mitigated using explosives prior to being opened to guests.

Feb 1, 2020

By Aris Tambunan, Nella Lubis, Nurafrianti Saala, Komang Widhiayanto, Herry Saputra, Rudolf Sitorus

Maximizing mining recovery rates and minimizing ore loss are pivotal objectives for economic efficiency and operational effectiveness. This study explores methods to address these imperatives by enhancing ore production and recovery through improved blasting techniques and spillage control in the Martabe Gold Mine Project in North Sumatra Province, Indonesia. Between 2018 and 2021, the average mining recovery rate stood at 93%, resulting in a potential annual ore loss of 7% and a potential quarterly financial impact of close to $2 million. Maintaining and enhancing mining recovery became crucial, with a planned 30% increase in total material movement for 2022. The mining recovery target for 2022 was set at 96% based on best achievement historical data from 2021 to increase ore tonnage by 203 KTon per annum. To achieve the primary objective of increasing ore production by improving mining recovery, the study focused on predicting and controlling the movement of blasted ore to reduce spillage and enhancing the grade control model to reflect actual conditions post-blasting. Several alternative solutions were explored, primarily emphasizing drilling and blasting activities. Essential methods included capturing the actual blasting movement to adjust the ore block based on blasting design data and post-blasting muckpile topography. This approach minimizes ore loss by providing output as ore block adjustment based on post-blast movement data. In addition, the tie-up design was adjusted to control ore spillage outside the pit ridge. The implementation of these methods yielded significant improvements. Adjusting the ore block based on actual blasting movement contributed $1,545,764 in benefits. Controlling ore spillage outside the pit ridge achieved a 10% reduction in spillage, contributing $79,184 in benefits. These enhancements successfully met the 2022 mining recovery target of 96%, marking a 3% increase from 2021. Consequently, ore loss was reduced by 178 KTon throughout 2022, resulting in a financial impact of $7.3 million. The study underscores the significance of precise blasting techniques and effective spillage control in enhancing mining recovery rates.

Jan 21, 2025

By Gabriel Gonzalez, Paulo Couceiro, Luis Manriquez, Alejandro Gutierrez, Juan Navarro

A high-stakes blasting campaign was successfully executed at a major open pit copper mine in northern Chile. This operation posed a significant technical challenge due to its immediate proximity to the tailings dam - a critical infrastructure whose structural integrity depends on strict control of blast-induced seismic vibrations. The geological complexity of the area, characterized by upper andesite interbedded with caliche (carbonate), further complicated the operation. This lithological composition, known for its high tenacity and cohesion, posed additional challenges for achieving effective fragmentation, necessitating a highly customized blast design and loading strategy. The campaign included four production blasts and one secondary blast, all executed under the constraint of not exceeding the Peak Ground Acceleration (PGA) threshold of 0.64g, as defined by the Maximum Credible Earthquake (MCE) scenario. To ensure compliance, geophones were strategically installed at three monitoring points (P1, P2, and P3) on the dam to capture real-time acceleration data. The use of specialized blast patterns, precise stemming control, and electronically sequenced detonations ensured that all recorded accelerations remained well below the critical threshold. A total of 496,163 tonnes of material were safely blasted, with 8,452 meters drilled and powder factors ranging from 419 to 594 g/ton. Therefore, this case study exemplifies operational excellence in controlled blasting, demonstrating the feasibility of safe mining near geotechnically sensitive zones through predictive modeling, rigorous QA/QC, and post-blast analysis.

Jan 26, 2026

By Tapan Goswami, Brent Geoff

Mining multiple steeply sloping coal seams introduces challenges in terms of safety and productivity. Work on steeply sloping surfaces for the processes of bench preparation, mark-out, drilling, loading and blast tie-up, coal cleaning and recovery is inherently hazardous. Furthermore, a large number of mining cycles is usually necessary, as small rounds are required and each layer is separately drilled, loaded, blasted and excavated. This exposes personnel and machines to additional risks and also incurs higher unit costs of mining as machine productivity is reduced. A case study is presented of a mine in New South Wales, Australia where three coal seams are separated by layers of inter-burden rock. Due to the unfavourable sloping nature of the coal seams the conventional practice was to drill and blast each layer separately.

Jan 1, 2010

By Braden Lusk

A typical rural house surrounded by a surface coal mine was instrumented in 2008. Information regarding ground vibration, airblast, and sounds inside the house was collected. Previous publications have included conclusions about this data with regard to blasting source (far-field or near-field) and results as to how the residents experience the blast were made. Several events were also recorded that were not related to blasting due to the nature of the trigger system. The trigger of the monitoring system was attached to one of the mid walls of the house, thus other normal daily events produced vibration levels significant enough to trigger the monitoring system.

Jan 1, 2011

By Gary Cavanough

The spontaneous exothermic reaction of ammonium nitrate explosives with sulphide-containing rocks, commonly referred to as reactive ground, is a site-specific condition that can lead to spontaneous detonations. Mine sites typically carry out regular assessment of ground for reactivity. In Australia, reactive ground testing is conducted according to the Australasian Explosives Industry Safety Group (AEISG) Code of Practice. This paper presents a new method to assess reactive ground. The new method can be completed on the mine site or in the laboratory. The new method allows samples to be tested in hours not weeks, as required when using the method prescribed in the AEISG Code of Practice. The new method also provides an explanation of why ground is reactive or not reactive, Whereas the AEISG Code of Practice provides a reactive, not reactive or marginal results with no understanding of reason for these results. Case studies on the use of weathering agents, pH, sulphide content and carbonate content will be reported. These case studies identify instances where the testing as per the AEISG Code of Practice provides false positive and false negative results. A false positive result will require the use of inhibited products when they are not actually required which increases costs and reduces productivity due to the need to used multiple explosive products. A false negative result increases the risk of an unplanned initiation of a blast hole.

Feb 6, 2023

By Sérgio Augusto Ferreira, Alan Gerson Diaz Butron, Carlos E. Arroyo, Marcus Neves, Jorhs Enrique Casimiro Huayhua, Dieggo Santos, Eventomar Junior

The presence of natural underground cavities is normally a characteristic of iron ore deposits, specifically in tropical deposits. Brazil and the United States are the only countries that have a legislation to protect these structures, but in Brazil this legislation is very specific for the existing cavities in the federal territory. These cavities are classified by their level of relevance as high, medium, and low. From this perspective, its preservation becomes mandatory, especially, for those of high relevance in order to protect the species (flora and fauna) that live in them. When these structures are within the production phases, it becomes a challenge to exploit these reserves with the use of commercial explosives, since these structures condition and may restrict the use and amount of explosive charge. This paper presents the methodology of controlled blasting associated with predictability via realistic simulation in production polygons, applied in a Brazilian iron ore mine where there is a presence of high relevance natural cavities with restrictions in relation to the limits of Peak Particle Velocity (PPV), which is product of detonation.

Feb 6, 2023

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Anderson Meireles, Leonardo Soares Chaves, Raul Carretero Hoz, Carlos Eduardo Soares Feliciano, Renato Jacome Costa

The large iron deposits in the northern region of Brazil located in the Amazon Craton have in common the presence of natural cavities. These cavities primarily occur in the upper layer of the ore body, formed above hematite mineralization. Their origin remains a topic of debate, often associated with hydrothermal drainage processes and erosive evolution. Over time, these cavities have become integral to the local environment, each contributing to the regional ecosystem of fauna, flora, and the significance of speleothems found within them. Managing these cavities poses a significant challenge for iron mines in the area. On one hand, they must preserve the cavities from anthropogenic actions, while simultaneously handling heavy equipment and large volumes. In 2023, the development of the mine took place towards the cavity under study, revealing systematic deviations in vibrations recorded during nearby detonations as the blasting got nearer. To address this, a work plan was put in place, emphasizing a straightforward approach: constructing lithology-specific vibration models, defining charge abacuses, and optimizing timing to reduce charge amplification. Implementing this methodology significantly improved adherence to the vibration limit, resulting in an around 50% reduction in standard error. This paper presents the consolidated work that allowed mining activities to continue in the area through controlled blasting, effectively mitigating potential anthropogenic damage in sensitive areas.

Jan 21, 2025

By Robert Hopler

THE work that is being done by the Government to reduce the dangers of mining was brought out strikingly in the First National Mine-Safety Demonstration which occurred at Pittsburgh, Pa., on October 30th and 31st, under the auspices of the United States Bureau of Mines with the assistance of the American National Red Cross Society and the Pittsburgh Coal Operators’ Association.

Jan 1, 2012

By Neal Lee, Braden T. Lusk, Brendan McCray

"Selection of a blasting agent for optimum performance is based on many variables. Often, a decision is made with regard to product cost and field testing. Defining optimum performance can be difficult, since downstream effects of fragmentation on loading, haulage, processing, and energy consumption are not immediately clear. Many operations are beginning to optimize their blasting programs “on the bench,” by utilizing information generated downstream at the loader and/or crusher. During the evaluation of a blasting agent, factors such as velocity of detonation, gas production, and sensitivity are typicallyconsidered. Alternatively, brisance (“the shattering power of an explosive material distinguished from its total work capacity”1) is not. Brisance affects the immediate area surrounding a borehole. Fractures produced here during the shock phase of detonation are believed to have an important effect on rock movement and fragmentation. "

Jan 1, 2017

By Felix Degold, Mark Ganster

Achieving a customer optimized fragmentation by using robust data from new technologies e.g. GPS positions of boreholes, fragmentation analysis to calibrate the geology and fragmentation prediction models. The inclusion of the collected data into the blast’s design makes it possible to accomplish a desired particle size distribution.

Feb 1, 2020

By Khushaal Popli, Vanessa Roeland, Brian Hall, Carl Diederichs

Highland Valley Copper (HVC) has embraced an integrated Mine to Mill approach to comminution since the late 1990s. Previous blasting optimization was carried out through adjustments to blast pattern geometry (i.e., reduction of burden and spacing). This approach proved very effective and HVC reduced the burden and spacing of high energy ore blast patterns to what was considered the practical limit that still allowed for efficient drilling and bulk truck loading operations. While mining in the bottom of the Valley pit near the end of the previous pushback, HVC encountered high static groundwater conditions which enabled the transmission of elevated inter-blasthole pressures that had the potential to exceed safe operating limits for initiation products. This risk was mitigated through an expansion of burden and spacing for the high energy ore patterns, reducing the application of blasting energy and increasing the average particle size in Mill feed.

Feb 6, 2023

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020