Search Documents

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor. If a blast is fired using 1.25" (32 mm) diameter product and a 10-foot (3 m) bench, vertical uplift of 60 feet (18.3 m) would be considered extreme and violent by any professional in the industry. However, a 100-foot-high (30.5 m) bench using 12" (305 mm) bulk product, having a vertical displacement of 60 feet(18.3 m)might be considered typical or non-worrisome. This is where violence factor is beneficial as itprovides a system of scaling the violence of a blast based on the bench height to give manager a keyperformance indicator (KPI) which is easy to monitor and can provide a large amount of information onsite-specific design variables for their performance on blasting and the end-results of the blast. The Violence Factor of a blast is an integer which is scaled to determine how high vertical uplift of a blast is compared to the bench height. This project analyzed numerous blasts to determine what blast design variables contribute to violence. This violence has also been shown to occur when a non-optimal breakage mechanism, cratering, occurs and the design criteria that lead to this cratering. Finally, this paper will present typical results of various levels of violence including backbreak, fragmentation, and muckpile configuration.

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By William Hissem

The topics in the title line of this article are desirable and applicable to entire industries that exist outside the realm of the ISEE’s readership. But the issues I will discuss herein are specific to those who drill, blast, and excavate rock as part of their business. Civil and site construction projects, mines, and quarries specifically comprise the group who will benefit from this discussion.

Jan 1, 2014

By Joshua Micah Hoffman

While it is easy to state that meaningful involvement of the community can play a critical role for a successful blasting operation, following through with this involvement is not an easy task. Structured Public Involvement (SPI) is a developed protocol for involving communities in project planning decisions and could be readily applied to the blasting industry. SPI was developed for the purpose of collecting quality public input about public transportation projects. The purpose of SPI is to bring about stakeholder satisfaction with potential projects by allowing controlled input from the stakeholders. It was designed and intended for democratic societies that have come to expect a voice in public projects. While blasting operations are not always in the domain of public projects, the fundamental process outlined by SPI can be useful for collecting feedback from the immediate public around blasting operations.

Jan 1, 2014

By Hairong Zeng, Matthew Baumann, Shahram Tafazoli, Edmond Chow

Measurement of rock fragmentation has evolved from a completely subjective and manual process to a statistically objective and semi-automated process. However, ultimately, the vision is to achieve a statistically representative and fully-automated process. From the blast optimization perspective, it is critical to receive reliable rock fragmentation results quickly to incorporate into the planning of subsequent blasts. Since manual rock fragmentation measurement methods tend to be time consuming, a fully-automated method is the practical way to meet these requirements.

Jan 1, 2012

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By C. Braun, C. Kennedy, P. Katsabanis

A series of small scale tests, simulating multi-hole blasts have been performed to establish the effect of delays on blast fragmentation. The blasts were performed in high quality granodiorite blocks, which were cut from stone prepared by dimensional stone quarry operations. The pattern used was equilateral triangular, with a distance of 10.2cm between boreholes, which had a diameter of 11mm, were loaded with detonating cord and the coupling medium was water. The delays used were achieved using different lengths of detonating cord for the cases of delays between 0 and 100 microseconds between holes and a sequential blasting machine firing seismic detonators for larger delays up to 4ms. All fragments were collected and screened. The experiments showed that the coarsest fragmentation was achieved with simultaneous initiation of all charges. Fragmentation became finer with delay time between holes up to 1ms between holes. The results show that in moderate to competent rock, similar to the granodiorite of the experiments, fragmentation optimization requires delays of few milliseconds per meter of burden. In view of the findings, which agree with previous published work, the current trend of selecting fast firing times for fragmentation optimization is questioned.

Jan 1, 2006

By Harry Thompson

In using explosives to blast stumps from the ground in order to prepare it for farming, it is comparatively easy to place the charge under a stump having a semitaproot or a lateral system of rooting by boring or digging a hole in the earth to a point under the center of resistance and deep enough to give the desired effect.1

Jan 1, 2015

By Ashley Haslett

A European Directive on Identification & Traceability of explosives came into effect on the 4th of April 2008. This directive is intended to establish a harmonised system for the unique identification and traceability of all packaged explosives, detonators, reels of detonating cord and primers used in civil applications across the European Union. The directive must be adopted into the national legislation of each European Union member state by the 5th of April 2009 with compliance achieved throughout Europe by the 5th of April 2012. The requirements of the Directive apply to all explosives manufactured, used and imported into the European Union from 5th April 2012.

Jan 1, 2010

By Tristan Worsey, Jhon Silva

The paper discusses a limestone quarry case study that looks at change in fragmentation due to using different charge sequences when using the regular rhythmic timing method.

Feb 1, 2020

By James A. Bachmann, Christopher J. Gray

On December 26, 1994, at 1:00 am, Santa Fe Pacific Gold's Twin Creeks Mine experienced a major highwall failure involving over 2.5 million tons. The resulting effects of this slide were thousands of ounces of gold that were now deferred and an unstable wall above which made mining the slough material unsafe.

Jan 1, 1996

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Dr. Calvin J. Konya, Anthony Konya

Blast violence has always been a criteria that has been analyzed without a quantitative approach relying on opinions of those viewing the blast and oftentimes does not transfer between open-pit mines, quarries, and construction projects. Added to this confusion is that on many regulate projects, such as U.S. Army Corp of Engineers construction projects, the definition of "flyrock" or violence can vary, and contractors must be able to meet this requirement. This project analyzed hundreds of blasts from various construction projects to develop a new metric to determine blast violence - the Violence Factor.

Feb 1, 2020

By Ph. D. Favreau, Favreau Patrice B. Eng, R. F.

Geology is important in mining by helping to identify the rocks which contain sufficient valuable ore to justify their excavation. Geologists give a geological name to each rock type, so geology is a player in blasting; when a blaster has successfully blasted rock of a given geological name at a former site, and he later has to blast rock at another site whose rock has the same geological name, then his first trial often is the same method as he used at the former site, since the geological name of the rock is the same

Jan 1, 2019

By Steve Linehan, John Toedter, Kelly Williams, Mark Herman, Laura Connor, Catherine E. Johnson

Minimum safe distance (MSD) calculations are used widely in military applications to determine safe standoff distances for breaching personnel. Accurate safe distances and an understanding of blast wave propagation are critical to preventing traumatic brain injury. These calculations are often based on spherical charges in open air. However, applications including explosive breaching use planar charges rather than spherical. Previous studies analyzed the shock propagation of a square planar charge of sheet explosive and concluded the anisotropic pattern conflicted with the Kingery Bulmash (KB) and MSD spherical models. It has been determined that these predictions do not adequately predict the realistic pressures in all directions and the trend has shown to be consistent across multiple charge geometries. In this series of experiments, pressures were collected from reference spheres and rectangular geometries of detonating cord and sheet explosive commonly used in breaching and improvised demolition for this comparison. This common configuration showed pressure differences at varying angles to the charge with the highest pressures measured at the 90° position perpendicular to the “door” to be breached. Lower pressures were found at the 0° and 15° positions where the breachers would normally be standing. The reflected shock from a surface such as a door was incorporated in a semi-confined situation and added to the shock observed by the breachers. Urban environments include many surrounding structures for these reflections to occur and further testing is necessary in such an environment to determine the full-scale impact. These findings may be useful to develop improved MSD calculations for breaching applications based on charge geometry, orientation to the blast, and nearby structures.

Feb 6, 2023