Search Documents

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coottha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1996

By A Tawadrous, P D. Katsabanis, S Kim

A series of small scale tests, have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite, Barre, Stanstead and Laurentian, were tested. The charge consisted of detonating cord placed in five holes with water as a coupling medium, or concentrated charges of equal mass of high exolosive, fully stemmed or air decked. Powder factor was varied from 0.39 to 1.17 kg/m3. Charges were detonated simultaneously or with a small delay and in some experiments, detonation waves collided in the middle of each borehole. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different levels of impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using standard Bond mill grindability tests. The experiments generally showed increased softening of the rock with powder factor, manifested by the increasing initial slope of the relationship between t10 and impact energy. The rate of change of the initial slope decreased with increasing powder factor. Changes in the work index were small and consistent in trend with the results of the single fragment impact characterization tests. Charge configuration, timing as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2009

By Thomas M. Keevin, Gregory L. Hempen

"Natural resource agencies, under various regulatory authorities, are challenged with permitting underwater explosive use while at the same time protecting aquatic resources. Deciding on whether or not to allow use of explosives requires striking a balance between development and aquatic resource protection. A company’s goal in underwater explosive use is to select methods that are both expedient and cost effective. The use of explosives is often the best alternative for engineering reasons or economic considerations. Over and above legal requirements, indiscriminate destructionof fish and other aquatic resources is not in a company’s best interests because of concerns relatingto public image, as well as the need to secure future contracts."

Jan 1, 1995

By Brian Carr

This workshop will display all of the existing products that are available as stemplug devices and discuss the general concept of the use of them. Actual results will be discussed along with several case histories. There will be adequate time for questions and answers.

Jan 1, 2000

By Robert B. Hopler

Explosives, originally used only in fireworks and warfare, became legitimate contributors to human progress when miners in Eastern Europe began using them to break rock in the early 1600%. Since that time these powerful materials have had a dual role in the world: as agents of destruction in war, and as irreplaceable tools necessary to advance civilization. In the latter role, they serve as agents to enable mankind to produce metals, build roads, and drive tunnels. In other words, to provide those materials, services, and infrastructure without which the modern world could not exist.

Jan 1, 1997

By Rufus Flinchum

Two of the most critical concerns a blaster faces today are airblast and flyrock. Airblast, sometimes called noise or overpressure, can cause damage to neighboring structures, especially windows. It also is the cause for many vibration complaints. The human sense of hearing is often more acute to identifying source than the sense of touch. When a blast occurs, the airblast is what identifies the event. The vibration that may be felt is then associated with the airblast. Vibrations of greater magnitude, such as passing trucks or construction work on the house, go unnoticed because their sounds are familiar or expected. Flyrock is the number one killer and cause of damage. Elasting laws provide limits for these two concerns. Failure to comply may result in fines, closing of the operation, and even prison. Airblast and flyrock originate from two distinct areas, the open face and the bench surface. Each of these areas is addressed in the detailed proven procedures that follow, and if used by the blaster in conjunction with his own blasting knowledge, a sound blasting plan can be developed to minimize the occurrence of airblast and flyrock.

Jan 1, 1992

By David Reddick

The mining industry is in the midst of dramatic change. Mining activities are moving from industrialized first world countries (Canada, Australia, and the United States) to the third world. This shift is occurring due to depleted reserves, tough environmental standards, and expensive labor in traditional mining countries. During a recent trip to South Africa, I was asked, owing to my educational background in economics and an international involvement in drilling and blasting, what changes could be anticipated in third world blasting practices as labor costs increase. It is from that beginning that this presentation has evolved.

Jan 1, 1997

By Gennaro Di Lauro, Laura Meraviglia, Demostenes Efstratiadis, Danilo Coppe

This paper presentation regards the European Union’s project “I.C.E.A. - Identification Colors of Explosives and Blasting Accessories (Agreement number – HOME/2010/ISEC/AG/071 – 30 – CE – 0447240/00-11), submitted under the call for proposal “ISEC 2010 ACTION GRANT” of the “Prevention and Fight against Crime” Program of European Commission. The main objective of the project is to simplify counter-terrorism security measures and the procedures for visual identification of blasting devices.

Jan 1, 2015

By Wilfred G. Comeao

Close-in blasting occurs every time the use o f explosives for excavation or demolition requires the surpassing of the commonly accepted cosmetic damage criteriain order to arrive at reasonable and practical explosive weights per delay. One of the many effective blast design procedures consists in establishing a reasonable charge weight per delay with respect to scale, geometry, costs, requirements and constraints of the project. Once this reasonable charge weight per delay is determined, it’s environmental effects have to be estimated with respect to the surroundings.

Jan 1, 1991

By Steve Dillingham

Here in the United States, as well as around the world, pose a daily dilemma - to wash or not to wash. Let’s face it, all trucks, especially our industry work horses - bulk trucks - get dirty. We all know that these units can be very expensive and washing them keeps your business investment looking new, improves public relations, fuels company pride, and facilitates equipment safety and preventative maintenance inspections.

Jan 1, 2001

By M. Ramulu, A. Raina, A. Chakraborty, Jethwa Choudhury, Dudhankar

Application of digital image analysis technique for assessment of blast fragmentation is gaining grounds in India, very recently. Central Mining Research Institute, India made its maiden attempt to optimize blast design based on fragmentation assessment of one of the biggest opencast mines of Singareni Collieries Company Limited, India. Indigenously developed photoanalysis software called ‘FRAGALYST’ was used for measurement of blast fragmentation A series of trial blasts were carried out in overburden benches with ongoing blast parameters and pictures of muck pile were taken by video camera for image analysis. Cycle time study of loaders and dumpers was done to determine machinery performance for each and every blast. Optimization of pre-blast parameters like specific charge, specific drilling and post-blast results like shovel cycle time and dumper cycle time, was done to determine optimum range of fragmentation. Interpreting the mean fragment size (K50) obtained by image analysis the blast design parameters were modified.

Jan 1, 2001

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By Kyle Wagner, William Joa, Colter Angell, Catherine Johnson, Marty Langenderfer, David Doucet

The goal of any business is to seek the maximum profitability for the organization through optimization the use of resources, processes and the application of new technologies. An analysis of various case studies demonstrate that blasting can have positive impacts on the crushing and milling processes resulting in increased profitability for the mining industry (Grundstrom, Kanchibotla, Jankovich & Thornton, 2001). This paper describes the case study of two copper mines in Peru producing Cu-Mo and Cu-Au concentrates, which together with their strategic partner, have implemented a project focused on the improvement of rock fragmentation. The project was based on techniques of pattern size reduction, the use of high energy explosives and the technology of electronic initiation. Combined, these techniques were shown to have significantly impacted the efficiency of downstream processes.

Jan 1, 2019

By Robert Hopler

Although electrical instruments were being widely introduced into the study of seismic tremors, attempts to understand and quantify shocks from blasting continued to use rather primitive methods well into the 19th century.

Jan 1, 2007

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

By Geraldine Woods

I work for the State of Washington as an Explosives inspector. My paper will describe the mission of the Wa. State Dept. of Labor pertaining to explosives and the regulation of explosives in the State.Blasting safety is high on the public safety list and the regulation of explosive use and storage has been mandated through legislature. The Dept. considers pro-active partnering forexplosive safety preferable to after-the-fact citations for non-compliance.In some cases, the Dept. will issue civil citations with monetary penalties, meant to be a deterrant, of course, to blasters who choose not to comply with the explosive regulations of the State.The Dept. has also revoked and suspended blasting licenses. In some instances, the Dept. has allowed recipients of citations with monetary penalties to reduce the amount paid by attending technical training classes. The idea here, is to reduce the chance of reoccurence of unsafe blasting practices. The State of Washington partners with MSHA in the regulation of explosives use and storage in mines, pits and quarries in the Stateas well as working closely with law enforcement, State and local fire marshals, ATF,and is active in ISEE in part of it’s ongoing effort to promote explosive safety and establish communications in a nonadversarial way with explosives users. My paper will include some statistics on licensing in the State, pounds of explosives used, inspection numbers, numbers and types of complaints with information from the inspections resulting of these complaints. My paper will include examples of storage, both good and bad, examples and pictures of fly rock incidents, accidents, near-miss close calls, break-ins, thefts, and abandoned explosives. This paper may also include a brief summary of my opinion of explosive regulation and my job as a regulator, including examples of high and low points of the job, joys and frustrations.

Jan 1, 2002

By Joseph Daly

This is the detailed evaluation of the establishment and implementation of an ‘oil recycle plant’ located on site at Boggabri Mine NSW, (Australia); its production, its use and its value. Also discussed in detail is the quality of the raw material produced, and the process and initial application of this raw material generated as well as the analysis of such, as a component within bulk explosive as applied to the mining industry as compiled during analysis. Laboratory analysis prior to field testing is also discussed including independent external laboratory analysis as well as the environmental benefits and a business case for recycled oil in blasting. This paper includes technical details of the product including densities, velocity of detonation and other associated key performance indicators. The intention is to off-set the amount of Distillate (Diesel) utilised as a component of bulk explosives, with a raw recycled oil and thus reducing both the environmental carbon footprint as well as production costs with regard to introduced petrochemical production and utilisation; an oil that is an existing recourse of controlled waste not only difficult but expensive to otherwise dispose of, whilst keeping the entire process ‘on-site’. Though recycled oil in blasting is not an entirely original idea, the key feature of this paper is the ability to complete the entire process on-site.

Jan 1, 2014