Search Documents

By J Parnell, B Manson

Bitumen occurs in the basins in reservoir sandstones, in veinlets close to hydrocarbon source rocks, in veins through lava beds and in sulphide-mineralised veins where it is closely associated with, but predates, the sulphides. The role of organic matter was probably in enhancing metal reduction by creating a low-Eh environment rather than in metal transport. Coeval euhedral quartz crystals or albite in sulphide-bearing carbonate veins provide evidence of an aqueous component to the hydrocarbon fluid

Aug 1, 1995

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By A. R. Naderian

Laboratory strength and deformation testing of freshly blasted sandstone and claystone overburden from Jeebropilly colliery in Queensland and in-situ plate-bearing tests on four backfills of different ages showed that the bearing capacity of backfill is a function mainly of compaction, not of age. The modulus or stiffness of the backfill is significantly increased by previous loading, in some cases up to threefold. Backfill material experiences some compaction through the passage of mining vehicles, likely to provide a bearing capacity that will support normal construction activities; the limited testing performed suggested that completed backfills are capable of supporting loads of up to 200 kN/m2 while sustaining displacements acceptable for a wide range of residential and industrial uses, but may be susceptible to collapse settlements due to saturation in the long term

Jun 19, 1905

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By F. C. Gennari, D. M. Pasquevich

With the gradual exhaustion of natural rutile, there has been extensive research into its synthesising from lower-grade titanium minerals. The removal of Fe from pseudobrookite (Fe2TiO5) by chlorination was studied, using both isothermal and non-isothermal thermogravimetric measurements. Correlation of the results obtained from element distribution maps, scanning electron microscopy, energy-dispersive X-ray analysis and phases detected by X-ray diffraction in the chlorinated samples showed clearly two associated processes. First, the pseudobrookite particles reacted with chlorine and iron was removed selectively as FeCl3(g), leaving a solid residue rich in the TiO2 phases anatile and rutile, separated from an inner layer of unreacted pseudobrookite by a distinct interphase boundary. Second, chlorine allowed TiCl4(g) to form in the reaction bed, where it removed iron from the Fe2O3 crystals as FeCl3(g) and substituted Ti through a pseudomorphic reaction

Jun 21, 1905

By P. J. Rowsell, M. D. Waller

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The applications of artificial intelligence systems in the upstream petroleum industry are reviewed. Particular emphasis is placed on current and potential applications in drilling engineering. Several recent advances in drilling technology have led to a large increase in the quality and volume of data available. This combined with the escalating cost, particularly of off-shore operations, is testing the traditional reliance on the skill and judgement of rig operators. AI systems offer enormous scope in enhancing and aiding the performance of these operations

Apr 1, 1994

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By M. V. Swain, N. Bristow, R. D. Dukino

During mining, crushing and handling the size of iron ore lumps decreases. Key factors in determining the amount and size of fines that are produced are the mechanical properties of the ore. In a continuation of earlier work on the same ores the mechanical properties of three Australian iron ores from Yandi, Koolan and Mt. Whaleback were determined. In particular, fracture toughness was investigated in greater detail by examining its relationship to crack length using the compact tension test. The elastic modulus and strength of the ores were also determined in flexure and compression. The results were interpreted using Weibull statistics, enabling the ores to be ranked according to strength and elastic modulus. These results, together with data on the mechanical response of the ores to stress and observations concerning the effect of mineralogy on cracking, provide a coherent understanding of the mechanisms involved when the ores fracture

Jun 18, 1905

By M. T. Styles, E. Condliffe, R. C. Leake, R. J. Chapman, D. J. Bland

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Quantitative point analysis and microchemical mapping identified 52 different types of mineral in inclusions, usually ranging in size from 5 to less than 1 micrometre, inherited from source bedrock. A combination of grain chemistry, heterogeneity and inclusions provides a grain signature reflecting the type and history of source mineralisation. Several grains from an alluvial site are needed, to allow for bedrock variation and the presence of inclusions in only 10-20% of grains. A total of 1 530 grains obtained from 30 localities in Scotland were of ten types, two of them minor variants. Two types in the Highlands may be related to centres of Caledonian igneous activity, but the most widespread is likely to have been of deep-seated origin and structurally controlled. Gold in the Ochil Hills is probably from a source associated with Devonian andesitic activity. In the Southern Uplands, grain types reflect two separate episodes of mesothermal lode gold mineralisation and relationships with Permian red beds/mafic volcanics and with Tertiary dykes

Jun 19, 1905

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

By A Cox

It has been demonstrated that all the cadmium from spent batteries, typically 4 g per battery, can be recovered by burning polyvinyl chloride waste to yield hydrogen chloride; this reacts to produce volatile calcium chloride, which can then be condensed and collected in a separate reactor. Alternatively, chlorine may be used to chlorinate the cadmium with equal efficiency. There is also a prospect of using very low concentrations of these gases, less than 1%, to effect the separation. The Cd was recovered more quickly when exposed to sustained, controlled flow rates of chlorinating gases, whereas when PVC was burnt most of the gas was produced in a very short time, not allowing complete reaction. This problem can be overcome by recirculation of the gas into the reactor. The technology is efficient and clean and the equipment used is simple, enhancing the prospects for a pilot-scale version of the process

Jun 21, 1905

By P. A. Davies

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 11pp., 15 refs. Hazards such as vibration, dust emission and fragment projection can result in an area called the Danger Zone being set around a blasting site. Traditionally Danger Zones have been set solely on the basis of consequences (e.g. based on the maximum distance of rock projection or expected ground vibration plus a defined safety margin). Advances in risk assessment and its growing acceptance as a safety management tool have led to the setting of Danger Zones based on both consequences and frequency of occurrence. This allows distances to be optimised on the basis of acceptable risk levels rather than the potential consequences of infrequent events. The setting of a flyrock Danger Zone is used to demonstrate a risk-based approach compared with a traditional consequence approach

Aug 1, 1995

By D. Bitzios, A. Gracia, V. Meggiolaro, J. D. Baker

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A large deposit in Spain and several smaller ones in Greece and Sweden were investigated. Beneficiation testwork, including the development of an innovative wet circuit, was undertaken in Italy. The Spanish Ilustracion deposit lies occurs in thin, white layers throughout a zone 35-40 m thick and 1.5 km long, in laminated calcsilicates. Total resources of more than 100 000 000 t include proven open-pittable reserves of 4 500 000 t averaging 35% wollastonite. The beneficiated product is suitable for various applications, including ceramics. The Swedish and Greek marble-hosted skarn deposits include Albatross, with 2 500 000 t of reserves at 30% wollastonite, and Panorama, with reserves estimated at more than 700 000 t

Jun 21, 1905

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By M. J. Scoble, L. M. Daneshmend, C. Hendricks

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. An attempt is made to relate emerging technologies to education and training requirements by examining the nature of the Canadian mining industry's human resources. Particular attention is given to the trends evident in mine automation and their likely impact on instructional needs. The characteristics of "computer-aided instruction" systems are reviewed and related to the implementation and support of mine-wide monitoring and communication networks, which are seen as fundamental to the eventual automation of underground hardrock mines

Apr 1, 1994

By A. Dean, J. Roberts, I. Stone, J. R. Merefield

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 10pp., 11 refs. No completely reliable method for characterising and quantifying airborne dust risk exists. A new monitoring technology has been developed whereby dust collected from four-way directional and high volume samplers is analysed for mineral content and particle size for integrated dust mapping. A dust database was set up for the area surrounding the Ffos Las open cast coal site in South Wales. It included XRD directional traces from 17 gauges over 20 months, XRD traces from window ledges in the nearby communities, the major soil types in the area, dust data from haulage roads and public roads and reference-type mineral samples. The database can be accessed relationally to compare and analyse the data using mineral, direction, time, weather and geographical relationships. The data has been used to assess areas of low, intermediate and high levels of risk from dust fall-out

Apr 1, 1995

By B. E. Burakov, S. D. Lupal, O. A. R. Thalhammer, B. Saini-Eidukat

Electric-pulse disintegration is a mineral separation technique that liberates all mineral grains from any igneous or metamorphic rock irrespective of its lithology or grain-size distribution. The normal mechanical crushing of whole-rock samples is replaced by the rending effect of an explosion, produced by applying an electric current from a high-voltage power source. A voltage greater than the 100 kV necessary for the electrical breakdown of rock samples is achieved by using capacitors charged in parallel, but discharged in series. The sample sits in a water bath and the rapid distribution of electric pulses leads to an explosion which occurs preferentially along grain boundaries of the sample. Individual, undamaged mineral grains can be recovered in their original shape and form regardless of grain size. Examples are given of the liberation and concentration of important accessory minerals from different rock types. The examples show the recovery of diamond from two types of non-kimberlitic host rock in Popigai and Kumdykol in Kazakhstan and platinum group minerals associated with chromitites from the Konjdor intrusion and sulphides from intrusions in the Kola Peninsula in Russia

Apr 1, 1995