Search Documents

By J. Matos e Silva

The paper refers two examples of structures located in seismic areas (Cases 1 and 2). The first one (Case 1) is the Torroal Bridge, located about 100 Km South of Lisbon, in the road Troia-Grandola. The horizontal loads due to the seismic actions were mainly carried by an anchor curtain connected, to the abutments, by reinforced concrete struts-ties. For the some purpose diaphragm walls were also placed under the pile caps of the column foundations. The second one (Case 2) refers to a building located about 50 Km South of Lisbon, at Sesimbra, near a cliff. To reduce the horizontal displacements of the structure due to seismic actions, in order to prevent the endangering of the cliff stability, an anchor curtain was adopted and connected, to the structure, by prestressed anchors.

Jan 1, 1996

By M. R. Madhav

The ultimate pullout capacity of single batter piles has been presented in literature in three contradictory trends. These trends are: the pullout capacity of a single batter pile increases, remain almost constant, or decrease with increasing the inclination angle of the pile. The present paper presents a theoretical study which explained these trends in terms of existing initial stress condition and the earth pressure coefficient at rest. The paper also presents a form of guideline for predicting the pullout capacity of inclined piles based on simple field and/or laboratory tests.

Jan 1, 2010

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014

By W. H. Liu

The stability of floors of large drydocks and wagon tipper sheds at coal terminals is an important matter but quite difficult to solve. Anchors can be used to join floors to foundations thus ensuring the stability of floors by the self-weight of floors and the pull of anchors. In this paper, the author describes the structures and types of the anchors used in the floors of the drydock in Beihai Shipyard and the wagon tipper shed at Shijiu Port, both in Shandong Province China, the determination of bearing capacity of anchors in rock bed of highly weathered granite, the comparison between prestressed anchors and non-prestressed anchors, the construction technology of anchors and the analysis of field experimental data.

Jan 1, 2010

By Brian Langdon

The DRIVEN GROUT PILE was developed in 1989 by DeWitt Construction, Incorporated. This piling essentially consists of a cost-in-place concrete piling that reacts on a steel boot that is driven to bearing. This report will describe the driven grout pile, its background and its installation. The advantages and disadvantages of this system are also discussed. Finally, the results of actual field installations are presented and discussed. BACKGROUND The DRIVEN GROUT PILE was developed out of a need for a low-cost high capacity piling (100 ton) that could be installed with ordinary pile driving equipment. This search was motivated by attempting to incorporate the material economy of an auger-cast piling with the "empirical load test" of a driven pile. Typically, the least cost material for piling in the 100 ton range is concrete (grout). A grout shaft with minimal reinforcement can withstand a compressive load of 100 tons for a material cost in the range of $6.00 to $8.00 per lineal foot. A pipe piling with a capacity of 100 tons has a unit material cost ranging to $13.00 per lineal foot. The marriage of these two advantages resulted in the DRIVEN GROUT PILE. A pile that utilizes the economy of a reinforced grout shaft and has the loading confidence of a driven pile.

Jan 1, 1990

1.1 The parties agree to submit all claims, disputes or controversies arising out of, or in relation to, the interpretation, application or enforcement of this agreement, including dispute resolution procedures, to sequential mandatory discussion, mediation and arbitration for resolution of all disputes before, and as a condition precedent, to self-help, arbitration, judicial action or other remedies. This mandatory procedure will resolve each dispute within one-hundred (100) calendar days. Any deadline falling on a federal holiday or weekend will be the next working day. Breach of this disputes process shall constitute a material breach of contract for which the aggrieved party may recover all costs, including attorneys fees, interest and other expenses necessary to resolve the dispute through litigation. The obligation to discuss and then mediate and arbitrate covers all disputes arising from every aspect of the Project to be built by the owner, including, but not limited to, design, engineering, bonding, indemnification, labor, material and services, and the acts or omissions of any related party for whom a party to this agreement may stand responsible.

Jan 1, 1994

By Roger Frank

"Abstract After noting the importance of standardization for piles, the European system is described (execution, tests and design, etc.). Some important aspects of Eurocode 7 are outlined (like the role of pile load tests). Finally, the calculation methods in the recent French standard for the design of piles following Eurocode 7 are shortly addressed.Importance of standardization for piles Like for other fields of geotechnical engineering, pile engineering is a complex art. For piles, the challenges are particularly numerous and many things must be mastered properly: - the soil investigation must be serious and adequate (for instance, deep enough!);- the choice of the pile type and the assumed behaviour must be assessed in order to reach a safe and economic design of the overall foundation;- the execution itself (construction and/or installation) deserves special attention and must follow strict state-of-the art rules.The geotechnical engineer, in charge of the design of a pile foundation, must have in mind the parameters linked to the variety of soils, of soil conditions and of pile types. A wide range of strong environmental issues are also to be considered: minimum disturbance during the execution processes, long-duration friendliness of the “inclusions” into the ground (to avoid pollution of the soils and waters, for instance) and respect of the neighbouring structures.Pile engineering plays in a world which is constantly moving and progressing: constructions expand in new difficult areas, actions on piles are more and more important, new execution techniques of piles are developed, research into the complex behaviour of pile foundations has no end, etc. Our views on how piles and group of piles really work are constantly evolving!"

Jan 1, 2014

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By Dan Brown

A method is outlined for computing the contribution of a micropile group to global stability of a sliding mass. The forces in the micropile are computed in a way which accounts for the effect of soil mass movement on the mobilization of axial and shear forces and which maintains compatibility between shear and axial force as a function of displacement. The method provides a rigorous model to incorporate the pile forces into the stability calculations, including the effect of pile forces on the resultant shear and normal forces at the sliding surface. This paper demonstrates the proposed solution using a simple example slope.

Jan 1, 2007

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Rick Ellman, Ian Chaney

"The Hampton Roads area encompassing the Norfolk, Virginia Beach and Newport News metropolitan region experiences some of the worst traffic congestion in Virginia. With continued growth of the ports and increasing demand, the Virginia Department of Transportation (VDOT) initiated the Downtown Tunnel/Midtown Tunnel/MLK Expressway Project, a complex undertaking critical to addressing the Hampton Roads area’s transportation needs. The project is a $2.1 billion Design/Build/Finance/Operate (DBFO) endeavor most notably involving the construction of a new two-lane vehicular tunnel utilizing the Immersed Tube Tunnel (ITT) method. The tunnel will pass under the Elizabeth River parallel to the existing Midtown Tunnel between Norfolk and Portsmouth, Va. It will be the largest design-build project constructed in the history of the Hampton Roads District.The New Midtown Tunnel will extend approximately 6,450 ft (1,966 m) along the north side of the existing tunnel where it ties into the existing Midtown Tunnel approaches in Norfolk and Portsmouth. It is being installed in a pre-excavated trench of which approximately 2,250 ft (686 m) required bracing on the Portsmouth side and approximately 1,000 ft (305 m) required bracing on the Norfolk side. The remaining 3,200 ft (975 m) of trench excavation was open cut dredging with laid back side slopes, optimized to reduce dredging, disposal and backfill quantities while also reducing the risk to the existing tunnel. The braced excavation portions of the tunnel alignment were divided into distinct segments which include: Portsmouth Approach Boat Section, Portsmouth Approach Cut-and-Cover Section, Portsmouth Dredge Section, Norfolk Dredge Section, Norfolk Approach Cut-and- Cover Section and the Norfolk Approach Boat Section. All “approach” excavations were performed in the dry and all “dredge” excavations were performed in the wet. Eleven ITT segments are being fabricated in the Sparrows Point Dry Dock facility in Baltimore, Md., and each 14,000 ton (12,700 tonne) segment is being towed approximately 220 mi (354 km) to the site. The ITT segments will extend under the Elizabeth River, with the deepest crossing 90 ft (27 m) at the Federal Navigation Channel. Once beyond the channel limits the ITT rises at an approximate 4.5% slope. Controlled screeding and element lowering operations will be performed primarily from floating barges."

Jan 1, 2014

By A. Boominathan

The behaviour of single piles under lateral dynamic loading is very critical and the study is still a current field of research since 1950's. Though many methods have been developed analytically to estimate the dynamic lateral stiffness, very limited dynamic testing on full scale piles were carried out to study the response of piles under lateral dynamic loading. Hence, field lateral dynamic vibration tests are conducted on driven precast concrete square pile of 400mm size and driven cast in-situ concrete piles of 400mm and 500 mm diameter at a petrochemical complexes site at Haldia (India). The results of steady state and free vibrations tests are discussed herein and compared with the response of the piles estimated from PILAY.

Jan 1, 2002

By A. Verghese Chummar

The paper presents a field study where the effect of negative drag caused the failure of a pile foundation system. Utilising the field observations the probable negative drag that acted on the piles is worked which gives an insight into the effect of negative drag on deep foundations.

Jan 1, 1996

By David A. Jack

The Mission Valley Viaduct is located in San Diego, California. This structure is the intersection of Interstate 8 and 805. The project consists of the main viaduct, 8 connecting ramps, and one highway overpass. This job was originally built back in the 70's. After the Loma Prieta Earthquake in 1989, Caltrans began an aggressive program to seismic retrofit all of its bridges throughout the state. Most retrofit designs required major upgrades to the existing footings. These footing upgrades consisted of either driven or drilled shaft piling. The existing footings of the Mission Valley interchange were supported on driven H pile. The soils throughout the site were dense sands and gravels, cobbles, occasional boulders with a dense sandstone bearing strata, which varied through out the site. It was this sandstone strata that the engineers designed their pile tips around. High ground water in sandy soils created a high probability of liquefaction in all of the upper stratas.

Jan 1, 1998

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By Janne P. Isohaka, Anssi M. Laaksonen

"Abstract In Scandinavia the use of steel pipe piles in bridge foundations started in the mid-1980s and has increased steadily since. As the piles driven in soft soils are slender, they can fail by buckling. Buckling usually requires taking into account the second order effect in structural and geotechnical design.The purpose of this paper is to derive formulas for demonstrating the theory behind the formulas given in literature for the second order effect of initially bent piles.IntroductionIn Scandinavian countries solid bedrock usually lies at moderate depth. If the bridge site is in an area where the soil above the bedrock is soft, the bridge is usually founded on end-bearing piles resting on the bedrock.The main purpose of the piles is to transfer axial forces into bearing soil. Like columns, piles can lose their stability by buckling when surrounded by soft soil. When axial compression on a slender, initially straight, pile reaches a particular value called the critical load, the pile is subjected to lateral deflection and loses stability. The soil around the pile suffers a corresponding deformation. This soilstructure interaction increases the critical load compared to a pile without surrounding soil.It is very unlikely that piles are ideally straight. Initial curvature along with curvature and deviation caused by the installation of piles causes bending moments to the pile when normal force is applied. These lateral displacements increase when normal force increases. This increase of moment is called asecond order effect.Eurocode and literatureEurocode 7 includes guidelines for the design of piles (Eurocode 3, section 5 includes design of steel piles). However, there are no clear guidelines for considering the second order effects related to piles surrounded by soil. Eurocodes advise doing structural design of piles the same way as in the case of columns. With columns, the second order effect is taken into consideration by multiplying the first order moment with the factor shown below (SFS EN-1992-1-1, 2005):"

Jan 1, 2014

Jan 1, 1996

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Jean-Louis Briaud

The following is a summary of a very recent report prepared at Texas A&M University for the National Cooperative Highway Research Program and entitled "Downdrag on Bitumen Coated Piles". Anytime the soil settles more than the pile, downdrag or negative skin friction will develop. The load in the pile increases with depth up to a certain point and then decreases down to the pile point. This phenomenon has been quoted as being the number one culprit for deep foundation failures. In Chapter 1, an introduction to downdrag is given. The most common criterion for downdrag is to consider it in design as soon as the settlement of the soil surface after pile driving exceeds 0.5 in. Coating piles with bitumen is an effective way of reducing downdrag forces and therefore allows to use smaller piles for the same load. This results in cost savings. Coating piles with bitumen increase the cost of piles by about 33% and therefore the decision to use bitumen is generally based on economic considerations.

Jan 1, 1989

Jan 1, 2003