Search Documents

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Arash Maghsoudloo, Asli Can

"Abstract This paper presents a ground improvement implementation case under a raft foundation of a local hospital. The selected ground improvement method is Wet Soil Mixing (WSM) technique. Soil mixing is increasingly applied to environmental applications and ground stabilization in geotechnical projects. In this technique, weak soil is mixed with cementitious slurry to improve the characteristics of the soil. The investigated case is one of the pioneering WSM ground improvement technique implementation cases in Turkey. The soil profile is mainly consisted of low plasticity clay. The effect of ground improvement is verified by a series of laboratory tests and four in-situ pile loading tests. The results of in-situ pile load tests on constructed soilcrete columns showed an acceptable factor of safety for the bearing capacity of the WSM columns. Measured bearing capacities in all four tested columns were nearly 20% higher than calculated values. In addition, a set of samples are obtained from the constructed columns and unconfined compression tests have been conducted. The laboratory test results indicate that the selected cementitious slurry has a sufficient efficiency to form the stabilizing columns.IntroductionIn the construction industry, stabilization of the soft ground by lime or cement stabilization is a widely used technique. In ground improvement systems deep mixing method (DMM) results in the same stabilization in deep portions of the soft soil profile by mixing cementitious slurry by means of mechanical augers. The pioneering cases of modern deep mixing application can be traced back to the year 1970 that was used for the stabilization of marine soils below the water level for the construction of harbor structures (Terashi et al., 1979). Nowadays, DMM is shown to be a proper and efficient method for the foundation of the structures and embankments on land. Some recent studies also reported that reasonable settlement reduction range in the stabilized soils under the foundation of structures (Archeewa et al., 2011). In addition to reduction of the structural settlement under service loads, deep mixing methods are also utilized when there is a concern with contaminated soil and groundwater or groundwater control (Andromalos and Bahner, 2003).Although, the DMM is shown to be a successful method in numerous studies for improvement of a wide range of soil types such as organics, fine-grained, and coarse grained material, it has some limitations (Archeewa et al. 2011, Jameson et al. 2010, Jelisic and Leppanen 2004, Lambrechts and Roy 1997, Meyersohn 2007, Miki and Nozu 2004, Olsson et al. 2008, O’Rourke and McGinn 2004, Stewart et al. 2004, Yang et al. 2011). High soil density and stiffness could damage deep mixing rigs. Engineering properties of the soilcrete columns changes based on the soil type, water content and other factors such as organic content of the available soil profile, so properties of the generated soilcrete should be verified by a set of rigorous testing procedures (Puppala et al. 2004).Based on the general classifications presented in the ground improvement literature, deep soil mixing method is divided into two main types of dry or wet mixing methods. In the dry and mixing methods compressed air and water are utilized as the binder transporter medium respectively (Moseley and Krisch, 2004). In addition, DMM methods can be categorized based on the employed mixing methods during the construction. In this study, the main aim is to present and elaborate on the selected method is known as Wet Speed Soil Mixing (WSSM)."

Jan 1, 2014

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By Amy B. Cerato

The application of this study is to use helical anchors as a foundation system for small wind tower (1 ? 10 kW) guyed cables. Helical anchors are currently used to anchor guyed cables of telecommunication and electric towers. However, the increased dynamic vibrations a wind turbine adds to the tower and foundation system under working loads, as well as extreme environmental conditions (e.g., straight line winds, ice load or sudden furling shocks), require additional knowledge about the behavior of helical anchors. These field conditions were simulated in this study by instrumenting a working tower with load cells and 3-axis accelerometers to gather data on wind speed and tower response. These tower responses were then transmitted to the helical anchors through an extensive, large-scale testing program that included monitoring the performance of the helical anchor foundation under dynamic loads, subject to natural variations in both wind regimes, precipitation (water level) and variations in helical anchor geometry. This paper specifically discusses the effects of helical anchor geometry on helical anchor performance under long-term dynamic loads.

Jan 1, 2008

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By B. Ladanyi

The design philosophies for piles in unfrozen and frozen soils are compared, and their similarities and differences are underlined. It is shown that in frozen soils, the long term behavior of a pile is difficult to predict, because of inadequate knowledge on the behavior of adfreeze bond with time, and on the value and variation of the lateral normal stress acting on the pile. Both of these problems are discussed in the paper on the basis of laboratory tests and theoretical analyses.

Jan 1, 2010

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the "strong" rock stratum, but did not correlate well with the design value calculated for the "weak" rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2005

By H. Meseck

The new building of the Central Bank of Iraq in Baghdad was footed in difficult underground conditions on more than 600 reinforced concrete driven piles, with cross-sectional diameters of 45 x 45 cm and pile lengths of 12.0 to 18.0 m. The necessary embedded depth and the bearing capacity thus reached were established on all 600 drives piles by means of dynamic pile tests. For the calibration of the dynamic pile tests, 6 static pile load tests were carried out. The execution of the construction and the results of the extensive tests on the building site are shown.

Jan 1, 1989

By Robert B. Bittner

Large diameter piles (2 to 3 m diameter, both driven and drilled) are being used more frequently by designers of bridge foundations. The use of these large piles allows the pile cap to be positioned off the bottom but usually still below water. Conventional cofferdams as shown in Figure 1 below are not suited to this type of pile cap. However, float-in cofferdams offer a viable alternative. This paper describes the float-in cofferdam system, its initial development for use on the Bath-Woolwich Bridge in Maine and its most recent application on the new Carquinez Bridge in California.

Jan 1, 2013

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By Henk E. Brassinga

In Rotterdam a number of underground parking facilities have been built and are under development in the inner city, and in the suburbs. These parking facilities are located at already densely built areas. The design of these constructions has to take into account the impact of the building activities and that of the final construction on the surroundings. In this paper some examples of the different building methods of newly realized underground parking facilities are described, and problems that occurred during the construction are pointed out. In the soil conditions as present in Rotterdam the cost effectiveness of underground facilities can be improved by deepening the parking facility, and at the same time reducing the surface area so that the total parking volume remains constant. In this way the total volume of the diaphragm walls and the costs of the project is reduced.

Jan 1, 2006

By X. L. Huang

This paper deals with the experimental and theoretic study of the contact pressure beneath the deep foundation of Beijing International Hotel, The experiments have been carried out in project and in model footing 6.6m2. The result of measurements shows the contact pressure at the edge is greater than that at the center. The theoretic analysis on the base of elastic theorey is in good agreement with the test if the proposed assumption used.

Jan 1, 2010