Search Documents

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By Yongjie Bu, Wei Sun, Zhiyong Gao, Yuehua Hu, Hongbiao Tao, Runqing Liu, Central South University

"The flotation behavior of O-isopropyl-N-ethyl thionocarbamate (IPETC) and pH for chalcopyrite and galena was studied through pure mineral test, adsorption quantity determination, solution chemistry calculation and Materials Studio simulation. The results show that the recovery differential value of chalcopyrite and galena is about 20% when pH of the pulp 9.5 and IPETC is 7×10-4 mol/L, the flotability differences of the two minerals is significant. There is competitive adsorption between OH? and IPETC on mineral surfaces, it lead to galena flotability is lower than chalcopyrite flotability. IPETC can remove the hydration layer on mineral surface and adsorb on active sites for collector adsorption, minerals have a better hydrophobicity.INTRODUCTIONCopper and lead are two of the most widely used metals in industrial and living, their applications include building construction, various metal alloys, heat and electricity, machine manufacturing (Zhang et al., 2014). Chalcopyrite and galena are the major source of copper and lead, normally they associated with each other. With the growing use of these resources, high grade and dissemination large particle sizes minerals are less and less, the use of low grade and complex dissemination minerals have to be paid more attention (Chen, Ye, & Li, 2010; Liu, Sun, Hu, & Wang, 2009). As the special properties and complex composition of copper-lead sulfide ore, flotation separation of chalcopyrite from galena effective is a research emphasis and difficulty point in mineral processing (Bruckard, Sparrow, & Woodcock, 2011).In the separation process of chalcopyrite and galena, it is rather important to choose effective collector (Huang, Wang, & Liu, 2014). Enlarging and using the two mineral flotability will be a good basis and start in flotation (Reyes-Bozo et al., 2014). Qin et al. (2013) made a great deal of research on flotation separation of copper/lead concentrate, collector O-isopropyl-N-ethyl thionocarbamate (IPETC), butyl xanthate (BX) and ammonium dibutyl dithiophosphate (ADTP) were investigated, BX and ADTP floated both chalcopyrite and galena well, specific adsorption appeared in the surface of mineral, the problem was the collectors were not selective enough, however IPETC showed better selective."

Jan 1, 2016

By V. Polotski

Initiated and financed by the Canadian Space Agency, Micro-Rover Platform with Tooling Arm (MRPTA) project has targeted the development of a robotic system with remote control and autonomous navigation capabilities for testing a large variety of analogous planetary missions. Although developed for planetary exploration, the navigation system is highly suitable to such areas of application as construction and in mining. Autonomous navigation system is capable of moving the platform to predefined position(s)/orientation(s) while continuously mapping the terrain, assessing its traversability and choosing most appropriate path to follow. Designed according to the JAUS (Joint Architecture for Unmanned Systems) framework, the system consists of several interconnected components. Following components are of particular importance: Pose Estimator (PE), Terrain Evaluator (TE), Map Manager (MP), and Path Planner (PP). The PE uses a minimal sensor configuration consisting of an azimuth gyroscope, inclinometer and wheel odometry. The PE provides reliable pose estimates in spite of pronounced slippage by employing extensive use of fused data. The TE uses a nodding laser scanner which continuously sweeps the area in front of the platform and constructs a ?traversability grid? (TG) of the surrounding area. Multiple TGs are constantly constructed along the platform motion path are combined into a terrain map maintained by the MP. The PP uses this map to compute a motion path Obtained path is executed by the motion controller and remains current until it is contradicted by the most recent map ? at which point it is re-planned. This paper addresses integration issues, lessons learned and also outlines the possible applications for construction and mining.

Aug 1, 2013

By W. M. Armstrong, John A. H Lund

The paper describes an investigation of some of the tensile properties of single crystal vanadium, poly-crystalline vanadium and polycrystal-line tantalum, in the range of: W°C to -196°C. Techniques employed in the preparation and testing of specimens are discussed in detail. Some results of determinations of the temperature dependence of yield stress and ductility are given, and discussed in terms of the Cottrell-Bilby Theory of yielding. At subnormal temperatures, all the body-centred cubic transition metals in the Periodic Table exhibit; a) the "yield phenomenon" in tension, b) a strong temperature and strain rate dependence of yield stress, and c) a large decrease or complete loss of ductility. The yield phenomenon (existence of an upper and lower yield point) has been explained by Cottrell and Bilby ( 1) in terms of the dislocation-locking effect

Jan 1, 1961

By C. R. Whittemore

Introduction The technical library in the service of industry is gradually becoming a well recognized and important part of all progressive industrial organizations. The larger mining, metallurgical, and chemical firms of Canada are establishing extensive reference libraries in connection with their research and operating departments in order that the members of the organization may keep abreast of the rapidly developing fields of engineering in which they are interested. It is the purpose of this paper to point out the usefulness of such a department in any industrial organization, to give a general outline of a system for filing and dispensing information, and to outline briefly the literature to be consulted and the procedure to be adopted in instigating a literature search. The technical library falls under the classification known as 'Special Libraries', and is quite different from the general library in that it is a storehouse of facts and owes its value to the ready presentation of information required for each specific case, and in a form most ready for use. The library brings all the available information relative to the interests of the corporation from without the plant to the organization within, and also keep in touch with each department of the organization.

Jan 1, 1930

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By W. D. Robson

THE prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first (1) was published in 1937; the second (2), in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research. HARMLESSNESS OF ALUMINIUM Animal experiments having served their purpose, it became necessary to consider means to test the discovery on humans. A question for immediate consideration was: Is aluminium harmful to man when inhaled as a fine powder? While the animal experiments were reassuring, since they conclusively showed the powder to be innocuous when breathed by animals, it was, nevertheless, desirable to have additional reassurance with regard to its effect upon human beings. Through the courtesy of the Aluminum Company of America and especially the valued interest in this problem displayed by that Company's Director of Research, Dr. Francis C. Frary, a study was made of the records pertaining to the health of a group of 125 employees who had for many years been engaged in the manufacture of finely powdered, metallic aluminium for the paint and ink industries. The conditions were such that these employees had inhaled varying and oft-times very dense concentrations of this powder daily over periods ranging from 6 to 23 years, the average for the group being 12 years. X-ray pictures of their chests showed no abnormalities attributable to aluminium. Their general health seemed better than that of the 3,000 workers in other sections of the plant. In fact, the early films of three employees in this group of 125 showed shadows suggestive of minimal tuberculosis, which shadows were not discernible in films taken after considerable periods of exposure to aluminium powder. The harmlessness of aluminium was, by this study, reasonably well established at the outset, a finding subsequently verified by Ontario research on humans.

Jan 1, 1944

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997

By L. E. C. Pignatari

Mine reconciliation is seen, for many, as a test of the quality of model estimates, while in fact it should be seen as a powerful tool for detecting and correcting problems in each step of mining operations, from resource estimation to metal production. Adequate reconciliation practices allow a more efficient control of the mining processes; however, its results can be illusory unless all parties involved have been in compliance with the principles of sampling correctness. This paper presents a new, segmented reconciliation matrix, which is based on the Theory of Sampling (TOS), developed to monitor gold operations and reserve estimation.

Jan 1, 2011

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By S. Glen

Cyanide management practices on modern gold plants are becoming more onerous, due to environmental pressures, particularly for signatories to the International Cyanide Management Code. Operations are therefore seeking to reduce levels of weak-acid dissociable (WAD) cyanide reporting to spigot discharge as well as to any eventual discharges from the tailings storage facility (TSF). Current gold industry standard processes primarily include the oxidation of cyanide by means of sodium meta-bisulfite (SMBS, or SO2) with air, Caro&apos;s acid (H2SO5) or hydrogen peroxide (H2O2). These processes require the transport and usage of expensive oxidizing reagents, along with the safety and environmental issues associated with these corrosive and toxic chemicals. Maelgwyn Mineral Services (MMS) has developed the MMS CN-DTM process, which utilizes the Aachen ReactorTM, a high-energy mass-transfer superoxygenation system, in conjunction with an activated carbon-based catalyst and no additional reagents, to increase the rate of cyanide oxidation to cyanate, the thermodynamically more stable form. Testwork conducted at the Maelgwyn Australia testwork facility in Perth Australia is described, at both pilot scale and continuous bench-scale, on a sample of tailings effluent obtained from an Australian gold plant. WAD cyanide is demonstrated to be lowered using the MMS CN-DTM process from an influent of 130 mg/L to the required levels for discharge to TSF (<50 mg/L). The continuous test results showed stable operation over three residence time turnovers. The pilot-scale results demonstrated the efficiency of the process at the reasonably large scales required for engineering cost estimation.

Jan 1, 2011

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By W. H. Moore

It seems necessary, at times, that we should reconsider some of the more obscure causes that lead to explosions of gas and coal-dust in mines, in the hope that a recapitulation will keep before us that old and true saying "eternal vigilance is the price of safety". This explosion, while not extensive (resulting in only two much to be regretted deaths) enlarged our vision as to the possibility and probability of other explosions with more disastrous results. As this is only a partial report I shall have to omit many things that are generally included in describing a mine explosion. The mine was worked exclusively with electric cap-lamps -only firebosses and other officials carried safety-lamps. All shots were examined and fired by firebosses with a small hand-battery. Monobel was used exclusively for blasting, and clay for tamping. The system of haulage iri use was main-rope and winches, horses being employed for gathering. Compressed-air was the motive power for all winches and pumps, excepting the pumps at the shaft-bottom which were steam-driven. The mine was wet with practically no dust anywhere, except what was being made at the coal-face in the getting of the coal. Gas was found occasionally, generally in the brushing, especially where the brushing was carried up to a small seam, 2 to 6 feet above the main seam. The place where the explosion took place was known as Leigh&apos;s heading, which was being driven to the rise, immediately inbye of the siding (off No. 1 left, off the new slope) and was about 90 feet up from the level.

Jan 1, 1926

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By C. Kim

The integration of three-dimensional (3D) data with infrared thermography has received much attention for its potential use as input data for building energy simulations. Therefore, researchers have proposed methods to integrate 3D data with infrared thermography obtained by different sensors. These studies show the potential of the integration of 3D data and infrared thermography using various systems. However, these studies have ignored property aspects of infrared thermography, such as the low resolution of infrared thermography and external environmental influences. Thus, their proposed methods to integrate 3D data and infrared thermography are inadequate because these problems can affect the resulting building energy simulation. This research proposes a framework that integrates infrared thermography and 3D data while accounting for the resolution and shadow effect of infrared thermography. The proposed framework consists of three steps. In the resolution enhancement step, bi-cubic interpolation is proposed. In thermal data correction from the shadow effect, the shadow area is detected from the visible image, and then the shadow effect is removed from the registered infrared thermography. Finally, enhanced infrared thermography is mapped to the 3D data obtained by a laser scanner. The performance of the proposed framework was evaluated using test images obtained from a building in operation. The experimental results show that the proposed framework provides a 3D thermal model that is useful and accurate in simulating building energy. It is expected that the 3D thermal model can be used for accurate energy simulation of existing buildings. In addition, the proposed framework can be applied in defect detection for buildings. Furthermore, this novel approach enhances infrared thermography using visible images.

Aug 1, 2013

By R. L. Veenstra

This paper explores the connection between the stresses observed and the failure mechanisms present in the modelled cemented paste backfill. In order to look at this connection, the authors have used a previously developed model to conduct a sensitivity analysis of the model?s strength and permeability input parameters. The results from the sensitivity analysis were then compared to determine what causes modelled stresses and failure mechanisms to vary. Increased insight into the behaviour of the modelled paste will help clarify how paste behaves in the field.

Aug 1, 2013

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By E. Ghali

"Corrosion of support system components (e.g., bolts, mesh, plates) is a safety and economic concern in underground mines. This paper reports the results of a five-year study wherein corrosion coupons were installed at select locations in participating mines, recovered at regular intervals, analyzed for signs of corrosion, and tested to quantify loss in capacity. Complementary tests were conducted on recovered mesh and friction bolt specimens. The data provide insights into contributing factors for support systems corrosion, which aid in the selection of appropriate support strategies and reliable assessment of the useful life and need for rehabilitation of a support system.RÉSUMÉ La corrosion des composantes des systèmes de soutien (p. ex. boulons, grillages et plaques) est une préoccupation économique et de sécurité dans les mines souterraines. Cet article présente les résultats d’une étude de cinq ans pendant laquelle des coupons de corrosion ont été installés à des endroits spécifiques dans les mines participantes; ces coupons ont été retirés à des intervalles réguliers, analysés pour des signes de corrosion et mis à l’épreuve pour quantifier la perte de capacité. Des essais complémentaires ont été effectués sur les grillages récupérés et sur les échantillons de boulons d’ancrage. Les données aident à comprendre les facteurs qui contribuent à la corrosion des systèmes de soutien, ce qui est utile dans le choix de stratégies appropriées de soutien et pour une évaluation fiable de la durée de vie utile et du besoin de remise en état d’un système de soutien."

Jan 1, 2015