Search Documents

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By L. Tong

"The oxidation of Quebracho was evaluated by acid-butanol assay, which indicates depolymerization of Quebracho. Anthocyanidin, an oxidation product of Quebracho, is stable at 95?C for up to 2 h. The ionization, complexation, and oxidation properties of Quebracho were discussed. Complexation of metal-Quebracho occurs at ambient temperature. The formation of complex precipitates is influenced by the acidity of the solution. Temperature is another important parameter that influences the oxidation and the complexation of Quebracho. Quebracho-ferric complex precipitate forms at 90?C, 0.1 mol/L H2SO4. The formation of Quebracho-metal complex in the leach solution is a possible reason for the consumption of Quebracho. Quebracho molecules adsorption on the mineral surface is reduced by consumption of Quebracho, resulting in poor sulfur dispersing effect in the leaching process. INTRODUCTIONQuebracho is used as a sulfur dispersing agent (SDA) in the pressure leaching of zinc concentrate as stated in U.S. Patent No. 3,867,268 (1975). It prevents the zinc sulfide particles from being coated with molten sulfur, thus preventing the inhibition of the zinc leaching reaction. Recently, the sulfur dispersing effect of Quebracho was investigated in the oxygen pressure leaching of nickel concentrate. The oxygen pressure leaching of pentlandite can be represented by reactions 1-3."

Jan 1, 2012

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005

By T. Xue, A. Singhal, D. Wrana, I. Mihaylov

"At Vale's Thompson Nickel Refinery, the copper and arsenic in the nickel electrolyte are removed by precipitation using H2S, generating a sulphide precipitate containing about 40% Cu, 8% Ni, 2 to 4% As and 30% S. This residue has been typically stored in impoundment ponds within the plant site. Various options for reprocessing it have been investigated over the years. One of the options involved oxidative pressure acid leach, whereby over 95% Cu, Ni and As were extracted. More recently, an atmospheric alkaline sulphide leaching process for selective removal of 70 to 90% As was developed and mini-plant tested. After alkaline sulphide leaching, the dissolved arsenic is precipitated as stable basic ferric arsenate (BFA) with the addition of ferric sulfate, while the low-arsenic Cu/Ni sulfide is suitable for processing in Vale's operations elsewhere in Canada.INTRODUCTIONVale’s Thompson Nickel Refinery was commissioned in 1961 and currently it has the capacity to produce about 56,700 tonnes per year of electrolytic nickel as cathode slab and rounds products. A sulphate and chloride mixed electrolyte is used in the Thompson refining process and it typically contains 75 to 85 g/L Ni, 50 to 60 g/L Cl, 90 to 120 g/L SO4 2-, 25 to 30 g/L Na and 8 to 9 g/L boric acid. The main impurities in the Thompson anolyte are copper, cobalt, arsenic, iron and lead.The simplified Thompson electrolyte purification flowsheet is shown in Figure 1 (Oliver & Wrana, 2009, Goble & Chapman, 1986); it consists of precipitation of copper, arsenic and lead with H2S, followed by nickel replenishment with ground matte and acid and removal of cobalt and iron with Cl2 and NiCO3."

Jan 1, 2012

By H. L. Noblitt, Pauline Moyd, Louis Moyd

The deposit, which forms a ridge -adjacent to the York river, in Mont-eagle township, is held by Monteagle Minerals Limited, of Toronto. The ore is in a Precambrian gneiss which is composed of nepheline, scapolite, andesine and microcline feldspars, muscovite and biotite micas, and -corundum. The major orebody is tabular and is exposed for 1,200 feet along the crest of the ridge. It aver-ages about 90 feet in thickness, dips at about 70°, and was intersected by drilling at a vertical depth of 600 feet. The deposit was prospected for corundum in the early 1900's. Recent exploration was undertaken to deter-mine its potential as a source of high-alumina ceramic material, with by-product corundum and white mica. The program included prospecting, mapping, trenching, diamond drilling, bulk sampling, beneficiation research, a large-scale beneficiation test, product evaluation, market investigations, and plant design. Reserves, to a depth of about 300 feet, are estimated at about 3 million tons.

Jan 1, 1962

By H. T. Kennedy, D. L. Flock

"The project described in this pa-per was undertaken to provide a more thorough understanding of the effect of contamination by drilling fluids on the electrical properties of porous systems. The basic work per-formed was filtration tests on both consolidated and unconsolidated sands and the determination of their resistivity profiles with the aid of screen-type electrodes spaced at convenient intervals along the core.Four drilling fluids were selected, ranging in resistivity from 447.0 ohm-cm. to •5.76 ohm-cm. The permeability of three unconsolidated and four consolidated cores, on which resistivity measurements were made, varied from 1,257 md. to 4,560 md. Five additional cores with permeabilities as low as 49 md. were tested to investigate the effect of permeability on the depth of invasion of drilling fluids.The effect of drilling fluid invasion on resistivity profiles was determined on cores containing brine only, and on those containing 80 to 90 per cent oil and 20 to 10 per cent brine. The study included measurements of (a) clay content of different sections of the core, (b) saturation of the invaded fluids and oil in different parts of the core, and ( c) changes in resistivity as a result of gravitational re-distribution of fluids and diffusion of electrolytes.The data showed that the resistivity of an invaded core is, as was expected, controlled by the resistivity of the filtrate, the resistivity of residual core water, the resistivity of the clay particles, and the amount and distribution of the filtrate, clays, residual oil, and brine. In most cases there was a significant increase in resistivity owing to the presence of clay solids which had invaded the core. The change in resistivity, as a result of the diffusion of salts, was substantial after a period of five hours. There is evidence in some cases that the residual oil and core water saturations of the unconsolidated cores, after substantial invasion, are very low, indicating almost complete displacement by invading fluid."

Jan 1, 1959

By D. W. R. Haysom

"I AM CONSCIOUS of the honour you pay me by having invited me to address you on the subject of the Rehabilitation of the Sydney Steel Corporation. The true architect of the revival and rehabilitation is Robert Burns Cameron. Because of the numerous myths which have grown up around what seems to be the miracle of the revival of the Sydney Steelworks, I propose to go back to the time when they came under the full control of the Province, on the 1st of January, 1968. Late in 1967, the decision was taken by Premier G. I. Smith to keep the Steel Plant running for at least another year, in an endeavour to see whether the enormous losses being sustained by Dosco could be reduced to a level which would permit their continuing operation. When that decision was taken, Dosco was to continue management until the 30th of April, 1968, and in the intervening period, the Provincial Government would seek management of the right calibre to ensure that an objective view of the Steelworks operations could be secured. By a combination of circumstances which can only be described as most felicitous, the man selected for the task was R. B. Cameron. He very quickly determined that to permit Dosco to continue management of the Steelworks until April 30 could only result in heavy losses to the Province and a consequent deterioration in the already critical financial position and a declining morale of the worke"

Jan 1, 1972

By Andrew J. Troop

"VAUGHAN THOMPSON designed the Thompson retrievable diamond drill wedge and reaming assembly in 1948. Since 1950, the Hudson Bay Exploration and Development Company, Limited has used the method extensively. The wedge, setting tool, and reamer have been modified slightly since they were first introduced. In 1951, Mr. Thompson designed the Thompson arc cutter. The purpose of this tool is to decrease effectively the diameter of the arc cut, using standard drilling tools. This directional drilling device is usually employed when a branch hole is desired. The Thompson arc cutter has been used with success at Birch Lake, Saskatchewan, at the property of Cuprus Mines, Limited, Manitoba, and at Thompson Lake, Manitoba.UsesThe Thompson retrievable wedge provides a simple method for:(1) Re-drilling lost core sections(2) Re-sampling sections of old holes(3) By-passing lost tools Correcting the direction of a hole(4) Drilling a branch hole to obtain intersections at a higher elevation than the original holePrevious to the spring of 1951, the wedge was used only for the first four of these purposes. Recently it has been employed extensively for drilling branch holes."

Jan 1, 1953

By F. H. Edmunds

Introduction This paper, it is hoped, will serve as an introduction to further work upon the origin of the soils and to a more complete interpretation of the geology of Saskatchewan from a study of the soils of the Province. The great difficulty that is encountered in mapping the structure of the prairie regions of the west must be evident to all who have made the attempt. The rarity of good exposures, due to the extensive coverings of glacial drift, is the greatest obstacle, making it difficult to determine the exact stratigraphical position of such exposures as may be found. In many cases palæontological evidence is lacking, or, if available, our present knowledge of the stratigraphy is insufficient to justify division of the formations into horizons; and until many of these formations have been subjected to petrographic investigation, little can be done in using lithological differences as an aid to the correlation of the usually sparse outcrops met with in the Province. Topography may be of the utmost value as an indication of geological structure when considered in conjunction with other evidence. It does not necessarily follow that, because an area in Saskatchewan has resemblances in surface configuration to an area of oil-producing land in Texas, there is sufficient justification for sinking money in wells without further investigation. Such - investigation should include the study of available soil maps.

Jan 1, 1929

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By H. Hejny

Economy needs mineral raw materials in almost each sector of modern life. They can only be provided by mining activities. An increasing share of the total mining production will be by underground mining. The mineral deposits will be found at gradually greater depths, including all problems associated with them. It involves an increase in overburden pressure with subsequent rock stability problems and risks of structural collapse. There is a need for new and safe technologies for almost all parts of a modern mine. The mining industry faces a number of challenges which require technical solutions that encompass the entire network and include the economic, social and environmental issues. The industry needs a new image based on pioneering solutions and a modern structure that can exploit minerals at greater depths and promote both high productivity and safe working conditions. Funding has been secured from the European Commission for the I²Mine project. Work started in November, 2011. This initiative is designed to focus on the technological challenges that the mining industry is currently facing including the exploitation of ever deeper deposits and the aspiration for an invisible, safe, zero impact mine. The project comprises a consortium of 27 organisations from 10 European countries. I²Mine marks the start of a series of development activities aimed at realising the concept of an invisible, zero impact, deep mine. The extractive sector, still seen as being old fashioned and environmentally unfriendly, will show that mineral extraction and processing can be done in a highly innovative and sustainable manner with low impact underground and zero impact above ground. The concept of I²Mine is to develop innovative methods, technologies, machines and equipment necessary for the efficient exploitation of minerals and disposal of waste, all of which will be carried out underground. This will dramatically reduce the volume of surface transportation of both minerals and waste, minimising above ground installations and reducing the environmental impact. New eco-efficient technologies will be applied in order to make the entire mining process more efficient and environmentally sound. The concept is for an integrated mine, with the majority of the installations underground, and only the final product will be transported above ground to be shipped to the customer. Production waste will be treated and stored underground and gaseous emissions will be managed underground as far as practical. I²Mine will also focus on ideas and concepts that increase energy efficiency and decrease waste. The core of the project will be to develop breakthrough technologies for autonomous, highly selective, continuous mineral extraction processes and machinery based on new sensor technologies, face front separation as well as innovative concepts for mass flow management and transportation integrating state of the art technologies. The concept of an invisible, zero impact mine requires a refined process underground that selectively extracts the mineral thereby reducing waste. For this reason, improved extraction machines and near to face processing methods, including backfill procedures, need to be developed. These developments include rock mechanics and ground control solutions, incorporating health, safety and environmental issues.

Aug 1, 2013

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By A. B. Baldwin

"Uranium and thorium mineralization occurs at several localities in eastern Quebec along the north shore of the Gulf of St. Lawrence. The main occurrences are near Sept-Iles, Baie Johan Beetz, Romaine and St-Augustin river. Mineralization occurs mainly as disseminated uraninite, uranothorite, uranothorianite, monazite and minor zircon and allanite. Yellow to orange oxidation products are observed along fracture planes of the uranium-bearing deposits to a depth of a few feet. Magnetite, biotite and smoky quartz have a distinct tendency to accompany the radioactive minerals. The host rocks include white to pink pegmatite, pink granite and also, in the case of the Romaine and St-Augustin River occurrences, cream to grey plagioclase-rich, well foliated paragneiss and migmatite. Radioactivity near secondary structures, such as fractures and joint planes, indicates some reconstitution of radioactive minerals.The North Shore of Quebec is the northeast extension of the Grenville sub-province. It is also a uranium-thorium metallogenic province."

Jan 1, 1970

By A. Alfantazi

Recently, titanium and its alloys have been the materials of choice for the liner and internal components of autoclaves used to extract Ni and Co from laterite ores. There have been many corrosion incidents ranging from localized attacks due to scale formation or welding, to damage caused by pockets of concentrated acid. Most of the literature focuses on methods to avoid the corrosion altogether. Little has been published to increase awareness of the chemistry at these conditions. For this paper, a literature review of the thermodynamics of titanium was undertaken to decipher the slew of information available. E-pH diagrams were constructed from select data and compared with the results of electrochemical experiments. Since nickel laterite leaching takes place in sulphuric acid, and in many cases chloride concentrations are very high, the Ti-H2O, Ti-Cl--H2O and Ti-SO4---H2O systems were considered.

Jan 1, 2004

By Witold J. S. Ostrowski

Stabilization of water-bearing sediments by the freezing method for shaft sinking has been used for over 80 years on the European Continent. The real application of this method in Canada started with the development of the potash mines in Saskatchewan during the past fifteen years. The great depth to which it is applied creates a number of problems which have to be seriously considered by engineers in order to produce a safe and economical design. Freezing depth, thickness of the ice wall, number of the freeze holes, capacity of the freezing plant, pre-freezing time, etc., are the most important points which have to be established. Recent field experience in freezing to great depth in the Saskatchewan area is immensely interesting and important for further development of our potash mining and the application of the freezing method.

Jan 1, 1967

By A. J. Oliver, C. E. O’Neil, I. J. Itzkovitch, V. A. Ettel

A new solvent extraction process for the separation of cobalt, copper and zinc from nickel sulphate process streams has been developed. It involves selective extraction of these elements with a quaternary ammonium thiocyanate dissolved in an aromatic diluent. The chemical principles of this process have been investigated and are described, together with background physico-chemical data relating to the use of this solvent. Long-term testing in a continuous "mini-plant" circuit gave high-purity nickel and cobalt products (Ni/Co —200011 and Co/Ni ~1000/1 respectively).

Jan 1, 1976

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By G. Goodlad

This paper describes some of the main aspects involved in implementing the European “Equipment and Protective Systems for Use in Potentially Explosive Atmospheres” (ATEX) Directive (No.94/9/EC) in the British mining industry by the year 2003. It provides a brief background to the Directive and considers its main objective of removing all barriers to trade in Europe. It outlines the need for the European Standards making bodies to write new editions of the ’explosion protection concept standards’ and for manufacturers to adopt new quality management procedures and develop new versions of equipment in conformity with the ATEX categories of “M1” or “M2.” Finally, it assesses the possible future relationship between the European enforcing authorities, manufacturers and users of explosion protected equipment.

Jan 1, 1999