Search Documents

By J. M. Livingstone

"This paper covers some of the problems confronted by Canada's railways in moving bulk materials from their source to the dock-site. The ""cost center"" concept is presented, and hypothetical examples of its use given. Also discussed are systems design, the unit train and pipelines.INTRODUCTIONCANADA LIVES BY RER EXPORTS and the Port of Vancouver by the exports of the Mountain and Prairie Empire at her back. The most recent estimates of off-shore shipments of bulk from the Port of Vancouver rise to 35.8 million shipping tons in 1985 and deep-sea general cargo estimates, in and out, are estimated at 7.6 million shipping tons for the same year. This compares to 7.67 and 2.87 million shipping tons, respectively, in 1965."

Jan 1, 1968

By Kevin C. Milne

"The solution of problems associated with development of a sour gas reserve will be of increasing importance in tl1e next few years if gas export is approved •by the National Energy Board. The purpose of this paper is to review briefly the history of the Carstairs gas field, and tCI describe in a general manner the reservoir, and the producing and processing facilities.HISTORYThe Carstairs gas field was discovered in April 1958 when the discovery well, Home Carstairs 10-17, was successfully completed as a gas well in the Elkton member of the Turner Valley formation. Geo-graphic location of the field is shown in Figure No. 1. Note that the field is about five miles west of the town of Carstairs, Alberta, which in turn is about 40 miles north of Calgary. Drilling subsequent to the discovery well resulted in three addition-al producing wells and one dry hole during I.958; two producing wells during 1959; and one producing well and one dry hole during 1960. Thus, seven producing wells and two dry holes have been drilled in the Carstairs field to date.In November 1959 a 12-section block in the Carstairs field was unitized on a surface acre basis. Mean-while, in June 1959, operators in the field executed an ""Interim Plant Agreement"" that provided the money needed to start construction of a joint venture processing plant and gathering system. Construction of the plant and gathering system was completed in February 1960."

Jan 1, 1960

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By Jae-sang Ahn

As the amount of construction information used in the growing construction field increases, the importance of efficient construction field management has been growing. Therefore, construction industry have been tried to introduce and conjugate various software and IT technology such as PMIS, Web Camera, RFID, GPS, PDA. However, existing IT technology especially PMIS have not been performed systematically because of difficulty of real time information collection and decision-making from the insufficient handy equipment. These problems make construction manager cannot efficiently respond to diverse condition occur in construction sites. In addition, after the completion, individual who use PMIS have to move another site and use another system so than cannot use information from previous sites. On the other hand, development of IT technology transmute PDA phone for text-based work like schedule management, internet research to smart phone for network based multimedia service. In other words, smart phone is not just IT equipment but new way for overall industry and it can satisfy the demand IT technology on construction sites. Therefore, the purpose of this study is introduce mobile based individual unit PMIS system using cloud computing and SNS which is in development progress. It is expected to be possible to collect and record the real-time information that occur at the site and make rapid decisions based on the recorded information, by converting the office works that are managed based on the site PC or Web, if the site management system that is based on the smart phones and Cloud computing that will be constructed through this research are utilized. After this study, it is necessary to research about interwork with project unit PMIS system and test on real construction site.

Aug 1, 2013

By Jos. Kalbhenn

MR. G. G. BOWSER: Mr. Kalbhenn's paper is an excellent one and is a concise description of a very interesting piece of work. It is well known that a great deal of preliminary study was given to this job before the final plans were made. It is due to this thorough preparation .chat the work progressed so satisfactorily, smoothly, and safely. The ideas carried out in the construction of the hardwood pack, timbered compartment, inclined raise, loading chute, and steel-boomed room, all contributed to a successful conclusion of the work. The extra care in being certain that the compartment shafts were well timbered was especially necessary on account of the difficult blasting conditions. In other words, the foundations .of this job were well and truly laid. The blasting in this work was very difficult due to the nature of the Strata. Working under an ever precarious roof condition and completing .this job with only two lost-time accidents is a record of which to be proud. The shaft men engaged on this work are also due for praise. I regret I did not visit this work while it was in progress. It was not in lack of interest. This, however, more or less proves that the blasting end .of this job went along with practically no trouble. I have seen the nature of the rock, as I made several visits to the tunnels while they were being put through from the Phalen to the Harbour seam. According to figures in Mr. Kalbhenn's paper, the explosives consumption works out to 1.61 pounds per cubic yard of rock in the solid, or 0.8 pounds per ton. The explosives consumption in the tunnels ran from 2.86 to 3.46 pounds per cubic yard or an average of 1.58 pounds per ton of rock. Of course, the rock in the shaft was blasted in the most economical way possible, as far as powder costs are concerned, as the face advanced at close -wright angles to the strata and gravity was acting with the explosive. The tunnels were driven nearly 'end on' the strata and bottom holes had to be lifted, and I believe there was some re-drilling of ribs left in the floor. I would like to congratulate Mr. Kalbhenn on his very fine paper.

Jan 1, 1944

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By T. Johnson, D. Kelley, J. Graham

"Hydrometallurgical processes can be exceptionally corrosive. Conditions associated with metal extraction and refining require materials of construction that can withstand process acids and acid chlorides at temperatures up to 90°C (194°F). Process vessels, piping, scrubbers and ducting can be rapidly compromised in these aggressive environments if not designed with care. Design engineers are challenged to find materials that can stand up to hydrometallurgical processes especially for copper, zinc, nickel, cobalt and uranium. This paper will evaluate material solutions to determine which provides attractive economics for initial procurement as well as high durability for reasonable life cycle costs.INTRODUCTIONMining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel cobalt and uranium have been particularly active.The world’s largest nickel mine – the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale’s Voisey Bay mine in Labrador. Voisey’s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $858 Million Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 – 250,000 MT/yr manganese carbonate.High nickel alloys and rubber lined steel have been used for decades to design corrosion resistant equipment for mineral processing environments. These materials demonstrate reasonable resistance to corrosion for most environments. Unfortunately, higher nickel alloys are quite expensive. Rubber lined steel is a bit more affordable but requires continuing service over time which ultimately drives up its cost as well. FRP (Fiberglass Reinforced Plastic) has also been used extensively in mineral processing for tanks, piping and ducting employed in aggressive environments. Today, more and more design engineers and material specifiers are calling for FRP composites for both new and replacement equipment used in the refining and processing of a variety of metal ores."

Jan 1, 2012

By N. Shi, T. G. Joseph

ABSTRACT One-twentieth-scale field trials for conventional and concept dipper designs were compared to mid- and ultra-class-sized conventional dipper performance. Digging effort was used as the performance indicator for comparison. It was shown that linear relationships exist between dipper capacity, suspended hoist load, and peak hoist load. A ratio of conventional and concept dipper performance at the 1/20th scale was then evaluated to allow prediction of the performance of an ultra-class concept design using an independent ultra-class conventional dipper dataset. The outcome indicated a peak hoist requirement of 15.5% less to achieve the same production as the conventional design.

Jan 1, 2011

By W. B. Agocs

"IntroductionWITH THE DISCOVERY of natural radioactivity at the end of the 19th century, and the design of equipment for the detection of this phenomenon, radioactivity surveys bad their inception. Early in the 20th century it was found that almost all rocks are radioactive to a certain degree. This radioactivity is due to the nuclear disintegration of six naturally radioactive elements: potassium, thorium, uranium, rubidium, samarium, and lutecium.The radioactivity of these elements manifests itself by the emission of some concentration of alpha, beta, and gamma 'rays'. Of these, the alpha and beta 'rays' are, respectively, helium atoms and electrons, while the gamma 'rays' are short wave length x-rays generated in the nuclear disintegration by the transformation of mass into energy.The alpha and beta rays, being particles of matter, are stopped ve• easily by material barriers, but gamma rays are extremely penetrating and they will pass through a foot or more of rock or several inches of lead.The radioactivity may be detected by the causing of ionization by the radiation. The radiation detectors may be divided into four classes: ionization chambers, proportion al counters, and Geiger counters, all of which use gas for ionization, and scintillation counters, in which a solid is ionized. The basic principle of all these detectors is the same; the difference lies in the method used to measure the degree of ionization produced by the rays. Currently, the scintillation counter is displacing, the other instruments in radioactivity surveying."

Jan 1, 1955

By A. D. Misener, L. G. D. Thompson

"IntroductionIt was shown by work previously reported that reliable geothermal gradients representative of various regions of the earth's, surface could he obtained from extended surveys of the rock temperatures in operating mines. These surveys showed the presence of anomalies in the isothermal levels and the existence of regions of regular behaviour. Below about 3,000 feet the temperature gradients became quite regular over the areas stud1ed. It is these regular gradients which are taken as representative of the region, wherever possible.The present paper describes the extension of this work which was undertaken to obtain further temperature gradients with a view to correlating them to other geophysical properties determined for the same regions. The additional data obtained have indicated possible reasons for the temperature anomalies. The experimental procedure was similar to that already described and was again made possible through the wholehearted co-operation of the management and the assistance of the personnel of the mines concerned. The research was entirely supported by a grant from the Research Council of Ontario.The equipment was a distinct improvement over that previously used and made it possible to take many more accurate temperature readings in a given time. Thermistor resistance thermometers were used, encased in silver sheaths and protected against damage by heavy copper casings. These were calibrated with a standard platinum resistance thermometer.The bridge used with these thermometers was one of a number designed and built by the Meteorological Service and designated M.S.C. Thermometer Indicator Type C-3. This very convenient and portable instrument operated from batteries in the instrument case. Multiple thermometer connections were provided so that rapid readings• of a number of thermometers was possible to accuracy of the order of 0.1°F. All electrical connections on the panel are covered with Dow-Corning ignition compound to prevent; electrical leakage due to moisture condensation. This, together with the high resistance of the thermometers and components of the bridge, gave much more reliable results than previously obtainable."

Jan 1, 1950

By R. V. Tomkins

Introduction In the past fifteen years, bentonite production in the United States has increased very rapidly. From l50,000 tons in l934, it rose to 400,000 tons in l 942 and to a record 920,000 tons in 1948. Occurrences of bentonite ?in western Canada were described in the early part of the century by Ries and Keele (3), Ells (2), Spence (4). and other officer of the Dominion Department of Mines, and, in Saskatchewan, Professor W. G. Worcester (6), of the University of Saskatchewan has explored and carried out tests on deposits of the material at various times during the past thirty years. Nevertheless, Canadian developments have not kept pace with those in the United States. Exact figures for total Canadian production are not released, but it is probably under l0,000 tons annually. There are a great number of uses for bentonite, but in the United States three alone account for 90 per cent of the consumption. These are for drilling gel, foundry sand bond, and oil decolorizer. The tremendous oil exploration programme on the Canadian prairies has increased the possibility of an adequate domestic market for drilling gel. Therefore, in Saskatchewan, our efforts have been directed mainly to the production of a good drilling gel, with a minor part of the project devoted to activation of bentonites for oil decolorizing.

Jan 1, 1952

By E. Peek, L. Becze, K. Reading

"Gallium oxide is an important semiconductor material used in optoelectronic devices (flat panel and solar cell) catalysts and sensors. One of the methods to produce ?-Ga2O3 is the so-called hydrothermal route. It is practiced by Neo Gallium Compounds and comprises of two steps: (1) the production of mainly gallium-oxy-hydroxide in a pressure vessel by reacting metallic gallium with water at 200-220 ºC and (2) the calcination of gallium-oxy-hydroxide at 700-750 ºC to convert it into ?-Ga2O3. This paper describes this pressure hydrometallurgy process supported with relevant thermodynamic data and presents the characteristics of the ?-Ga2O3 powder produced for commercial purposes. INTRODUCTIONGallium is a relatively new metal, having been predicted by D. Mendeleev in 1871, discovered by P.E. Lecoq de Boisbaudran in 1875, and first commercially produced in the USA in 1943. Gallium is not rare, being more abundant in the earth crust than antimony, bismuth, molybdenum, silver and tungsten. However, few gallium minerals exist in nature, and the dispersion of gallium within other minerals add to the complexity of its recovery. In practice, gallium is found in dispersed state primarily in bauxites and in some sphalerites, and, to a much smaller extent, in some coals. At present, a very large proportion of the primary gallium in the world is recovered as a by-product of aluminum plants, mostly Bayer plants, where gallium is extracted from a bleed of the Bayer liquor (Roskill, 2011). In 2011, world production of primary gallium was estimated at 200 metric tonnes. In addition, there is a significant contribution of recycling to the overall yearly availability of the metal.Gallium exhibits fairly remarkable properties: it is liquid above 29.76 ºC, can be supercooled, and with its high boiling point (2204 ºC), is the metal with the widest liquid range. Gallium is magnetic, and is an excellent conductor of both heat and electricity. Gallium also displays a marked anisotropic electrical conductivity (Roskill, 2011). All these properties render gallium almost irreplaceable in the semiconductors (GaAs, GaN, GaSb, GaP wafers) and the optoelectronics industry (flat panel, solar cell)."

Jan 1, 2012

By B. A. Monkman

"IntroductionONE OF :THE most effective methods by which the construction industry is combatting mounting building costs is by making increased use of lightweight materials, thus reducing the dead load to be carried •by structures. This applies to non-metallic materials as well as to metallic ones, and particular attention has been given to developing lightweight aggregates for use in concrete.The use of lightweight aggregates is not new and, in fact, dates back to the Roman Empire, when pumice was used in the walls and domes of the Roman buildings. More recently, and up to a decade or so ago, the demand for these aggregates was met from deposits of volcanic cinders, pumice, scoria, etc., and from the by-products of blast furnaces and coal burning boilers. However, these sources of supply are no longer sufficient to meet the demand, for transportation costs pretty well restrict the use of the natural lightweight aggregates to the western cordillera regions where the deposits of these materials occur, and the use of expanded slag aggregates to the areas neighbouring the plants where slags are produced. As for cinders, the supply has been greatly reduced by the conversion of industry to fuel oil, natural gas, and powdered coal, and the large stockpiles which existed previously have been pretty well exhausted.Industry's approach to the problem of a decreasing supply, in the face of an increasing demand, has been characteristically direct. The solution has been to construct plants whose sole .purpose is to produce economically an acceptable light-weight aggregate from materials close at hand."

Jan 1, 1955

By E. Herrera, L. Mariscal

"Ilo Copper Smelter operates since 2007 with an ISASMELTTM furnace as a single smelting unit (1,200,000 tpy) associated with two Rotary Holding Furnaces for separation of matte and slag, and which directly produces a discard slag. Southern Peru continually has been improving the slag chemistry of its ISASMELTTM furnace in order to reduce copper losses, given its big economic impact due to large slag mass generation. The present paper describes the influence of the CaO, Al2O3 and magnetite content in the slag of the ISASMELTTM furnace correlated with the SiO2/Fe ratio and its liquidus slag. Also it defines the best slag chemistry and operating practice in order to reduce the copper losses without compromise the bricks life of the furnace.INTRODUCTIONIlo Copper Smelter of Southern Peru (Grupo Mexico) is located on the southern coast of Peru, and treats mainly copper concentrates produced in its own mines (Toquepala and Cuajone).The modernized smelter was commissioned in 2007 and operates with an ISASMELT™ furnace as a single smelting unit (1,200,000 tpy), which is associated with two Rotary Holding Furnaces (RHF) for separation of matte and slag. This slag is directly sent to the dump. Figure 1 shows the smelter flow diagram.The ISASMELT™ process is a bath-smelting process using a single lance. The lance tip is immersed into a molten slag bath contained within the stationary, vertical, refractory-lined ISASMELT™ furnace. The injection of oxygen-enriched air, through the lance into the slag results in a highly turbulent molten bath. Feed material falling into the turbulent bath from above reacts rapidly, resulting in extremely high productivity for a relatively small bath volume."

Jan 1, 2012

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By M. H. MacLeod

"IntroductionTHE ORE PASS raise system at the H.B. mine as contracted by the Patrick Harrison Company consisted of two raises 6 ft. by 10 ft. in section •at 60 degrees to the horizontal. No. 88-88 raise, the longer of the two, was a straight raise 690 feet long, with access only from the bottom. In addition, this raise had two branch knuckle-backs only one of which was driven by. the Patrick Harrison Company. The other, known as 88-89 raise, was 540 feet long with knuckle-backs at 280 feet and 410 feet. Its access, also, was from the bottom (see Figure 1)."

Jan 1, 1954

By M. Sagedahl

The off gas from a smelter is cooled and dust removed in an electrostatic precipitator before approximately 95% of the sulphur dioxide (S02) is converted to sulfuric acid. However, the tail gas may need to be polished to remove the rest S02 to meet demands. A flue gas desulphurization (FGD) system, as usually applied to S02 removal on coal and oil fired Power Station, is suitable for polishing tail gases from copper smelters. The ALSTOM Seawater FGD process makes use of the alkalinity in the seawater to absorb and neutralize S02. Before being returned to the sea, the seawater is treated to comply with environmental regulations. As the ALSTOM Seawater FGD process uses no reagent and produces no byproduct, it is extremely cost-effective for coastal installations. The first SWFGD plant started operation in 1968. Over 60 of these units have been installed worldwide. The ALSTOM Seawater FGD process removes S02 from flue gas flows corresponding to a total of 70,000,000 Nm3 /h. Suitable for thermal power stations, smelters and oil refineries, ALSTOM Seawater FGD plants efficiently treats flue gases in the range of 300,000 Nm3/h to 2, 700,000 Nm3 /h per FGD plant, containing 20 - 6,500 ppm of S02.

Jan 1, 2007

By W. H. Fertl, S. J. Pirson

Well logging techniques, as used successfully in oil and gas exploration, can also be used to give a detailed evaluation of drill holes through industrial mineral deposits such as sulphur. This paper describes the logging tools used gives the theory behind the well-log interpretation and discusses the application of the method in sulphur-bearing limestone and m more complex sulphur deposits.

Jan 1, 1970

By Dan Miners

"This presentation will provide an overview and understanding of Mine Safety and Health Administration (MSHA) and Ontario Regulations for Mines and Mining Plants. It includes discussions on the history and practical development of the standards and an overview of engineering best practices from a construction, maintenance and operational viewpoint. INTRODUCTION Ontario is one of the safest mining jurisdictions in the world and has some of the most comprehensive regulations for the construction, operation and maintenance of a mine. In the USA, several operators have adopted some or all of the practices prescribed by the Ontario Regulations as an internal procedure. Experience has demonstrated that these plants are indicating less unplanned downtime and fewer issues with MSHA inspectors in their hoist plants. HISTORY AND THE REGULATIONS Both Canada and the USA have had some form of laws governing the operation of mines since the late 1890s. The paths of legislation have run in reasonably parallel lines, continually improving the health and safety conditions in the mining industry. Ontario Mine Health and Safety In the 1970s the accident rates in mining were higher than any other industrial sector; this prompted a Royal Commission on the Health and Safety of Workers in Mines (the Ham Report). The recommendations of this report, published in 1976, generated several changes in the regulations regarding worker safety in mines. Following the release of the Ham report, the Occupational Health and Safety Act (OHS) was passed by the Legislature in 1978. The Act is a set of comprehensive laws governing almost all Ontario workplaces, and it replaced separate laws governing different industrial sectors. OHS is enforced by the Ministry of Labour (MOL), and this discussion will focus specifically on Ontario’s Occupational Health and Safety Act, R.R.O. 1990, Regulation 854, Mines and Mining Plants, Part X Mine Hoisting Plant (Ontario Regulations). USA Mine Health and Safety A coal mine explosion in West Virginia and medical studies on occupational disease led to the 1969 Federal Coal Mine Health and Safety Act (Coal Act). The Coal Act was the most comprehensive and stringent Federal legislation governing the mining industry to date. The Mining Enforcement and Safety Administration (MESA) was formed, following the 1973 Act, as a new departmental agency to assume the enforcement of safety and health in mines. The Federal Mine Safety and Health Act of 1977 (Mine Act) transferred enforcement responsibilities from the Department of the Interior to the Department of Labor and named the new agency the Mine Safety and Health Administration (MSHA). This agency enforces the Code of Federal Regulations (CFR), and this discussion refers to CFR Title 30 Mineral Resources, Chapter I Mine Safety and Health Administration, Department of Labor, Subchapter K—Metal and Non-metal Mine Safety and Health (MSHA)."

Jan 1, 2019