Search Documents

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By James B. Templeton

"IntroductionWith the steady rise of the cost of coal and freight, the time is now ripe for an investigation into the feasibility of using the heat pump for heating purposes in fairly remote industrial areas.The gold mines of northern Ontario seemed to be a most likely place for the application of the heat pump.It was decided that the first step in the investigation would be to determine what economic advantage was to be gained by using the heat pump and thereby determining whether a further and more detailed research programme was warranted.If we can use the heat pump with economic advantage, we can reduce our mining costs and make a worthwhile contribution to our national economy by reducing the import of U. S. coal.The investigation was conducted under the auspices of the Nipissing Fellowship and directed by Professor R. E. Barrett of the Department of Mining Engineering, University of Toronto.With the able guidance of Mr. C. S. Gibson, of the Mines Accident Prevention Association of Ontario, the author visited the following mines: Mcintyre-Porcupine, Delnite, Dome, Lake Shore, Wright-Hargreaves, Kirkland Lake, Macassa, and Kerr Adcliso11.In all cases, the management and technical personnel of these mines were most co-operative and helpful in supplying information and ideas.It should be emphasized at the outset that the design and operation of the heat pump itself is by no means complicated or even new. The reason we hear so much about it today is because there have been improvements in compressors, motors, and heat exchangers in the past few years, and because fuel and freight rates have risen to such a point that, in some cases, the heat pump now has an economic advantage over other methods of heating."

Jan 1, 1950

By H D. Smith

T HE production of coal in Canada was slightly higher in 1964 than in the immediate past, and the major users continue to be the electric utility and metallurgical industries. There are continuing trends toward the increased use of cokes and chars in various metallurgical applications. Geological Research During 1964, the coal drilling program of the Research Council of Alberta (RCA) was concentrated in the extreme south of the Province (notably in the Milk River area and the region immediately to the northeast of this area). Field work commenced on June 1 and was completed at the end of September, by which time a total of 376 holes, aggregating some 48,500 ft., were drilled in 132 townships. Although no new major coal occurrences were intersected, the pro-gram yielded useful data for defining the extent of the known coal deposits in the area. Detailed results will be analyzed during the winter and reported in due course. Meanwhile, a full report on the

Jan 1, 1965

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By Jacek Paraszczak, Stefan Planeta

"RésuméDans la première partie de cet article on discute Ie contexte technico-économique de l'usage des foreuses à l'eau sur béquille dans des mines sud-africaines. Par la suite on présente les résultats d'une étude comparative du forage avec les foreuses à l'huile et à l'eau par rapport aux foreuses pneumatiques. La performance des foreuses est discutée sous les deux aspects: l'aspect technique concernant Ie taux de pénetration et la quantité d'eau rejetee dans les galeries et l'aspect de fa santé et sécurité au travail, et plus particuliérement, les niveaux de bruit et de vibrations ainsi que Ie brouillard de l'huile. On conclut par l'évaluation du potentiel de forage à I'aide des foreuses hydrauliques dans Ie contexte canadien.AbstractIn the first part of this paper the technical and economical aspects of water-powered drilling are discussed. This technology, originally employed in South Africa, received some interest from Canadian mine operators. In this context a comparative experimental study of pneumatic and hydraulic (oil- and water-powered) jackleg drills has been realized. The performance of the drills is compared and the results reviewed with regards to technical aspects (penetration rate, amount of water spilled) as well as health and safety considerations (noise and vibration level, presence of oil mist). The potential for application of hydraulic jackleg drill is discussed."

Jan 1, 1995

By D. M. Rippley

THE St. Lawrence Seaway Project ranks with the greatest engineering undertakings of all time. A summary of major materials going into the construction of this project, shown in Table I, will assist in an appreciation -of this fact. These data relate to Seaway construction only, and it should be remembered that two large-scale power projects are in the construction stage on the St. Lawrence river concurrently with construction of the Seaway. A project of such magnitude as the Seaway would attract widespread interest even if it were being constructed in a remote area. The fact that it is located in a heavily populated and developed section of both Canada and the United States has done much to enhance this interest, and in many ways complicates the problems confronting the engineer in the design and construction phases. Many consider the St. Lawrence Seaway to be a new idea that has developed within the past decade - such is far from the fact, because the St. Lawrence River canal systems have existed for more than a century, and the Seaway Project is but a new, larger, and more efficient version of a continually expanding facility.

Jan 1, 1957

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By Jeremy Breker

Cameco aligns its social and environmental responsibilities with its vision, mission and values. Environmental Leadership is established as a corporate objective that emphasizes the triple-bottom-line and a systematic approach to understanding environmental, social and economic issues, risks and opportunities. These are ingrained in the project culture, systems and processes and used to influence solutions derived by the project teams to achieve Cameco's objectives. This paper traces the organizational objectives from the early stages of a project through to implementation and turn over to Operations. A case study is used to demonstrate how an asset is influenced by Cameco?s strategy.

Aug 1, 2010

By Eric J. Grimsey, Don C. Ibana, David E. Grimsey

The segregation process as applied to nickel laterite ores involves the formation of gaseous nickel and iron chlorides which are subsequently reduced to form ferronickel on the surface of a solid carbon reductant. A fundamental study of the process has been carried out using limonite, nontronite and garnierite ores. The study highlighted the significant impacts that ore mineralogy and carbon addition have on the amount of nickel which is segregated rather than retained within the ore due to in-situ reduction. These important aspects affecting nickel recovery and the success of the process are discussed in this paper.

Jan 1, 2017

By R. Poulin, M. R. Samis

Real options valuation is an alternative net present value framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the lowgrade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The real option model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2006

By M. Cai

"It is well known that Peak Particle Velocity (PPV) plays a critical role in triggering rockburst damage in burst-prone underground mines. To estimate the PPV distribution around excavations, advanced numerical modeling can be used. In wave propagation numerical modeling, velocity field is often assumed to be uniform around an excavation. However, it is observed that wave velocities near mine openings are not constant, but rather non-uniform. Wave velocity in a rock mass depends on many factors such as rock quality and confinement. In particular, confinement has a large influence on wave velocity. The confinement around an excavation is low at the wall boundary and increases gradually and reaches a constant value far away from the excavation boundary. Hence, stress redistribution due to excavation will have a profound influence on wave propagation in underground mines. A better understanding of the influence of excavation effect on wave propagation helps to interpret the field observation of rockburst damage and improve mine safety. For this purpose, a non-uniform velocity model need to be constructed and the influence excavation effect should be taken into account in numerical wave propagation modeling.In the present study, a non-linear velocity model is developed firstly by considering the influence of confinement on wave velocity. This model links wave velocity to confinement explicitly. A coupled numerical method is then developed and used to study the seismic wave pattern around excavations in underground mines. Two codes, FLAC and SPECFEM2D, are coupled in the analysis. The motivation of developing the FLAC/SPECFEM2D coupled approach is to take merit of each code, such as the stress analysis capability in FLAC and the powerful wave propagation analysis capability in SPECFEM2D. The coupling process is realized through three steps: (1) static stress redistribution around an excavation is analyzed in FLAC; (2) data for coupling analysis, such as non-uniform velocity field (based on the new developed velocity model), mesh, absorbing boundaries, etc., are generated by FISH functions in FLAC and passed to SPECFEM2D; and (3) wave propagation modeling is performed in the SPECFEM2D considering a fault-slip seismic source. Because stress redistribution around the excavation is considered, non-uniform velocity field for the SPECFEM2D model can be obtained and this is a notable feature of this study. Very large difference in the S-wave response in these two modeling approaches with uniform and non-uniform velocity fields can be seen from the modeling results.Using the FLAC/SPECFEM2D coupled modeling approach, accurate velocity models can be constructed and this in turn will help to produce accurate PPV distribution around the excavations. Accurate PPV contours can be used to identify high rockburst risk zones for improved dynamic ground support strategy."

Jan 1, 2015

By Les Philips

National Institute for Safety and Health?s (NIOSH, USA) Office of Mine Safety and Mine Safety and Health (OMSHR) has definitions for: -Proximity Detection as detection of personnel, vehicles and other objects near a machine using some type of sensor technology -Proximity Warning (aka Collision Warning) as detection of personnel, vehicles and other objects near a machine resulting in alarms that ?Warn the operator only ?Warn the operator and nearby personnel (two-way) -Collision Avoidance as the processing of sensor information resulting in control signals or actions that alter machine status/movement to avoid a collision by ?Computer control ?Human control

May 1, 2013

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

ABSTRACT Based on mineralogical characteristics and processing techniques required, gold ores can be classified into 12 types: gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper-gold ores, porphyry copper-gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores, and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type differs and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ore and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2013

By R. Guimarães, L. Silva, J. Milboume

The São Bento concentrator was built by Gencor in 1985 to treat refractory gold-bearing flotation concentrate. The plant was the first commercial application of pressure oxidation for refractory gold ore following about a year after the first use of pressure oxidation on a whole ore at Homestake's McLaughlin operation in California. Ore from the Sao Bento mine is remarkably consistent in gold grade and arsenic and sulphide concentration as is typical in banded iron formations (BIF) (l). Gold content is approximately 9 g/t with approximately 30 - 40% free milling. The balance is associated with arsenopyrite and pyrrhotite. An expansion of both process facility and mine was undertaken between 1996 and 1998, raising the treatment capacity from 32,000 t/mo to 45,000 t/mo.

Jan 1, 2004

By A. M. Nordale

Let us first trace a line, mentally, across Alaska and Yukon, starting at a point in the west slightly south of the delta of the Yukon river and from there continuing eastward, loosely following the 63rd parallel of latitude until we have passed beyond the eastern border of Yukon. We will make two pronounced digressions southward to include the greater parts of the Iditarod and Tanana River valleys. That visualized line roughly defines the southern boundary of permafrost. North of it lies a vast region, fully three-fourths of the area of the two territories, which includes Seward peninsula, the great Yukon River basin, and the tractless wastes of the Arctic. During some frigorific cycle in the distant geological past, the ground there was frozen to a depth of many hundreds of feet. How deep the frost actually penetrated is not known, but it has been found to exceed three hundred feet in many places. Nature afterwards provided a perfect insulating cover in the form of heavy moss and dense grass, which has protected the ground from the heat of the sun's rays during the intervening ages. This frozen condition has always been accepted as something indigenous to the North and little thought was given to -it until recently, when the United States Government and, I believe, the Canadian Government, began extensive studies of it, particularly in respect to its effect and bearing on the development of the great oilfields of the Arctic. Within this large region and but a short distance south of the Arctic circle are the three principal producing placer gold fields in the sub-arctic, whose hubs centre at Nome and Fairbanks in Alaska and at Dawson in Yukon Territory. The geological structure and history of the gold-bearing deposits of Dawson and Fairbanks are very similar and probably closely related. They are typical placer deposits produced by stream action during periods of erosion and inundation and subsequently covered with a thick layer of fine, powdery silt mixed with decayed vegetation which, locally, is termed 'muck'. The depth of muck varies from less than 10 to more than 250 feet, with the greater depth near the lateral edges of the valleys. The gravel underlying it is medium in size, well rounded, and composed mostly of quartz and schist. The proportion of sand or fines is approximately 40 per cent. No large boulders and little clay are found, for those districts, as well as that of Nome, have not been subjected to glaciation. The most common bed-rock found is either decomposed or hard schist, but infrequently it is slate, quartz, diorite, or a porphyry. The vertical concentration of the gold is invariably on bed-rock and in the lower few feet of gravel which overlie it. The horizontal concentration or paystreak is roughly parallel to the trend of the valley but does not ordinarily coincide with the course of the present stream. The width of the paystreak usually expands from a few feet at the head of a creek to several hundred feet near its mouth.

Jan 1, 1947

By S. F. Featherby

"This paper traces briefly the historical development of coal handling systems to meet the needs of a rapidly developing thermal power generation technology. The wide range of operating requirements is demonstrated by comparing and contrasting the Wabamun GS of Calgary Power Ltd. and a typical modern Ontario-Hydro thermal plant. The problems of safe storage of large tonnages of coal in stockpiles are discussed, together with recommendations for stockpile management. The development of coal bunkers and their management is discussed in detail, together with future trends in the industry."

Jan 1, 1966

By R. Llewellyn

"Wear damage is responsible for very high maintenance costs and significant production losses in the oil sands industry of northern Alberta.It affects all areas of operations and involves a panoply of wear mechanisms from low stress sliding abrasion at extremely frigid temperatures during winter mining, to elevated temperature erosion/corrosion in processes where bitumen is converted to lighter hydrocarbon products.There is no universal panacea to defend against such diverse attack and a wide selection of resistant materials and systems is employed. These range from relatively soft rubbers which rely on their elastic properties for their protective capability, to some of the hardest ceramics and cermets which are currently available commercially.Details are presented of the characteristics and forms of the variety of wear materials being used and how they relate to the requirements of their areas of application. The review focuses on the practices followed at Syncrude Canada Ltd., which is the larger of the two commercial oil sands plants."

Jan 1, 1997

By E. J. Burrough

MR. J. J. McIntyre (International Coal & Coke Company, Ltd., and McGi1livray Creek Coal & Coke Company, Ltd., Coleman, Alta): Mr. Burrough's excellent paper, Metallurgical Coals of the Crowsnest Area, seems especially timely now, when the need for developing iron industries in the west, as well as in the east, is receiving so much attention. His -thorough review of the 'coking' industry is an especially valuable contribution, along with which the following brief remarks on coking in the Crowsnest Pass area of British Columbia and Alberta may be in order. When the Crowsnest Pass line of the Canadian Pacific railway was built there were great expectations for the non-ferrous metal industry; quite a number of smelter's were al-ready in operation in British Columbia and the northwestern United States, and further expansion was confidently expected. The suitability of the medium-volatile coking coals of the Pass for making metallurgical coke had been recognized from the time the fields were first explored. By the time the mines were fairly well developed there was already a market to war-rant the building of coking plants, and a common belief that expansion of the market would require a large coking industry. The first coke production was from plants built by the Crowsnest Pass Coal Company, Ltd., at Fernie, B.C. in 1903, and the International Coal and Coke Company, Ltd., at Coleman, Alberta. These plants were followed by others built by the Crowsnest Pass Coal Company, at Michel, B.C., by West Canadian Collieries, Ltd., at Lille, Alberta, and by Leitch Collieries, Ltd., at Passburg Alberta, and by a plant at Hosmer, B.C.

Jan 1, 1951

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977