Search Documents

By T. G. Joseph, M. J. Bolster

ABSTRACT This paper explores passive seismic measurement as an alternative, nonintrusive approach to conducting annual brake testing on surface mine sites. Dictated by the test site location, this evaluation adhered to the brake testing procedure as per British Columbia occupational health and safety regulations. Results showed excellent correlation to those reported via conventional practice: Comparing stopping distance, time, and velocity for the proposed instantaneous passive seismic versus conventional approaches, less than a 0.5% variance was evident. A viable alternative, the passive seismic approach, allowed an entire fleet of trucks to be sequentially evaluated for annual brake testing without disrupting operations by installing mechanical testing equipment.

Jan 1, 2012

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By W. A. Lang

Introduction That the coal industry has entered a new phase in its development is now evident. Coal, besides being the chief source of heat and power, has become a potential raw material for many industries. Rapid progress has been made in the methods used in the mining and preparation of coal, and in the equipment for the burning of coal. Data of a fundamental nature relating to the composition of coal and to its transformations? during combustion and processing have also been revealed. Research, the key which has opened this new era, has already accomplished much, but it has only begun to show what it may and should be able to do. New developments of coal burning equipment, super-power plants, carbonizing and briquetting plants, hydrogenation and synthetic chemical processes, will undoubtedly have a marked influence in the post-war years on the economic welfare of many coal producing countries. Until comparatively recently, however, there has been in many branches of the coal industry a tendency to regard research as something abstruse and something which had little or no value to those managing such branches. But the fact that coal has suffered as a source of heat and energy through inroads of oil, natural gas, and water power, has made it plain to the industry that, if it is to maintain its present markets in this competitive world, much less increase them, the whole industry must be willing to follow the example of other industries and plan for the future.

Jan 1, 1946

By C. Matthews, A. Vo

"Australia is one of the world’s leading exporters of bulk commodities and the extensive use of sampling equipment is key to the successful management of each mining operation. At the process plant, without a full understanding of the feed, product and tails, it is impossible to fully optimise the performance of the plant, such that the metallurgical balance is often open to error. At the port, a statistically correct, bias free and compliant sampling system is crucial to ensuring exported minerals are reflective of their true value and to avoid penalties. Over the last decade, as a result of the iron ore boom, there has been high demand for reliable, representative and standard compliant solids sample systems in Australia. This paper reviews several solids sampling applications at Australian mine sites, the challenges and experience gained and how the implementation of reliable representative sampling systems has provided better understanding of plant process performance, improved plant control and overall benefits to the operations.INTRODUCTION Mining is the primary contributor to the Australian economy with Australia ranking in the top 4 in economic resources for 21 primary industrial minerals in 2016 (Britt, et al., 2017). Australia is one of the world leaders in the export of the majority of its commodities including gold, copper and iron ore (Britt, et al., 2017). Therefore, a suitable and standard compliant sampling system is essential for evaluating plant performance and content verification. At the mine and at the port, the larger iron ore miners in Australia have developed stockpile models to predict the grade of their ore down to individual blocks of the stockpile. This allows the miner to create the right blend of material for sale to their customers and ensures they are not underselling their product or at risk of penalties for impurities or low grade. As an example, the average difference between the benchmark 62% Fe and low grade 58% Fe fines at the time of this report averaged US $30/tonne according to the Metal Bulletin Iron Ore Index. At a shipload of 180kt this would be a variation of US $5.4M. Whilst this is an extreme example, it highlights the economic importance of producing the correct grade product and a recognised representative sample of said product."

Jan 1, 2019

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By I. Masters, K. Buban, M. Faris, M. Antonio, M. Collins

"AngloGold Ashanti Brasil, with assistance from Sherritt International Corporation, has recently commissioned a new autoclave for the pressure oxidation of refractory gold feeds at their Corrego do Sítio operation in Brazil. Design of the new plant, including feed acidulation, pressure oxidation, oxidized solids washing and solution neutralization circuits, was based on the results of test work conducted by Sherritt at their pilot plant in Fort Saskatchewan, Alberta. This paper describes the results of the pilot plant study as well as highlights of the design exercise.INTRODUCTIONAngloGold Ashanti Brasil (AGA Brasil) has recently commissioned a refractory gold pressure oxidation plant at the site of the original São Bento operation in Brazil. The design of the São Bento pressure oxidation facility was based on Sherritt technology; Sherritt carried out the original process development test work in the mid-1980s, provided a process design package and detailed specifications for critical pressure oxidation equipment and participated in the training of operators and commissioning of the plant. The São Bento plant was operated between 1986 and 2007, when the original ore body was exhausted (Silva et al., 2004). AGA Brasil purchased the facility from Eldorado Gold in 2008, with the intent of refurbishing the plant to process refractory gold concentrates produced from the nearby Córrego do Sítio mining area.Sherritt International Corporation has a long history in the development and application of commercial pressure oxidation and pressure leaching processes. Sherritt’s development of technology for the pressure oxidation of refractory gold ores and concentrates commenced in the 1980s in collaboration with Homestake for application at the McLaughlin project in California. This was followed by several commercial applications in Canada, Papua New Guinea and Brazil (Berezowsky et al., 1991). More than thirty pilot plant campaigns investigating the pressure oxidation of refractory gold ores or concentrates have been conducted by Sherritt since the 1980s, and projects with Sherritt contributions to the process development studies and/or engineering design account for about half of the commercial plants that have operated to date with this type of process (Collins et al., 2011a; 2011b)."

Jan 1, 2012

By J. E. Hawley

This paper constitutes a report from the Committee on Geological Research to the Geology Division of the Institute. Two years have elapsed since a formal report was made containing several resolutions aimed at assisting geological research, a review of research equipment available, a summary of research projects suggested for consideration, and a list of research then in progress (see July, 1947, Bulletin, pp. 351-370). At this time we may note what action has been taken on the various resotions and suggestions of the Committee, indicate the more important accomplishments of independent investigators, and present a summary of the rather imposing volume and variety of research currently being carried on throughout the country. I.-Committee Resolutions and Suggestions 1.-A National Advisory Committee on Research in the Geological Sciences The original resolution adopted on the setting up of this Committee was approved with despatch by Council and was forwarded to the Minister of Mines and Resources. Due to a reorganization in the Department and possibly other reasons, no action on this important matter has yet been taken, but we are assured that some time this year such a Committee will be established by the Department of Mines and Resources. Unquestionably, it will give a fresh impetus to research in the geological sciences. When the noteworthy progress made by the research committees on Geophysics and on Soil and Snow Mechanics, established by the National Research Council, is considered, it is indeed regrettable that the Department of Mines and Resources has not acted more decisively in this matter.

Jan 1, 1949

By S. L. Gertsman

Canadian steel foundry practice has made marked progress during the past decade. Equipment suppliers, development engineers, and foundry personnel have focussed their attention on every phase of the foundry operation, with a resulting lower demand on manpower and materials. Also, more rigid specification requirements as to dimensional tolerances and quality have necessitated improvement and increased control at every stage from the pattern shop to the cleaning room. The growing trend toward mechanization is clearly evident. Equipment such as sand mixers, sand reclamation systems, material handling devices, moulding machines, core blowers, etc., is being increasingly employed by the steel foundryman. This equipment not only increases production but also tends to lessen the human variable so prevalent and disconcerting in the early days of steel founding. The result has been an improved and more reliable steel casting, which is gradually obtaining wider acceptance by design engineers. The purpose of this paper is to discuss briefly some of the practices being used, and also the direction of development that is being pursued by Canadian steel foundrymen.

Jan 1, 1948

By J. O. G. Sanderson

Introduction In this paper it is proposed to review the history of petroleum geology in western Canada, to discuss some of the main events which have affected its progress, to mention its relationship to the petroleum industry, and, finally, to appraise its present status and possible future importance. It will be useful first to consider the meanings of the terms petroleum geology, petroleum geologist, and the petroleum geology of a terrain. Petroleum Geology. - In simplest terms, geology is the science of the earth. Hence petroleum geology is the science of that portion of the earth that encloses pools of petroleum. The systematic delineation and study of stratigraphic geology began about 1820. The systematic development and study of petroleum geology started about 1910. It is a relatively immature branch of geology. Petroleum Geologist. - This term may be applied to a fully qualified geologist who is engaged for a time, be it a job, a contract, or a lifetime, in the work of finding and developing deposits of petroleum and related substances. No man may properly be called a petroleum geologist who is not first a fully qualified geologist.

Jan 1, 1946

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By E. Poiate, P. R. Cabral, A. V. N. Santos, P. V. M. Costa, C. S. Amaral, A. M. Costa

This paper discusses the design of underground salt caverns, opened by solution mining, for the production of brine and storage of natural gas under high pressures. The caverns are located in the salt basin in Maceio City, Alagoas State, at the northeast region of Brazil. Special attention is given to the geomechanical structural design of the caverns using computer codes specially developed for the simulation of excavations in salt rock formations, considering validated constitutive creep laws under different initial stress states and temperatures. The behavior of sedimentary rocks intercalations presented in the salt layer is simulated using elastic-plastic models. The excavation of the caverns by solution mining is also simulated starting from a geostatic initial equilibrium state of stresses, with a unique formulation only implemented in these computer codes, without the need of the application of boundary stresses to the model in order to develop the initial state of stresses. These computer codes have being used in the design of several clusters of caverns for brine production used as raw material of Poly Vinyl Chloride (PVC) of the Chemical Industryin Brazil. These computer codes and methodology were also applied to the design of the underground conventional potash mine in the state of Sergipe, overlying tachyhydrite and carnallite with very high creep strain rate. They have also been used in the design of the pre-salt oil wells through thick layers of stratified salt rock in Santos Basin, for the exploration and production of the pre-salt reservoirs in Brazil. The constitutive creep equations implemented in the codes are based on a double mechanism creep law. The creep constants adopted in the simulation are taken from a previous investigation carried out on an experimental panel of the potash mine, considering the stratified geology with different salt rocks of the basin where the mine is located. These constants were also obtained by lab tests under different confined and differential stresses and temperatures.

Jan 1, 2015

By K. M. Wild, C. D. Martin, F. Amann

"Argillaceous rock formations, in particular clay shales, are notorious for creating challenges in rock engineering. Due to their generally low hydraulic conductivity and their complete saturation in their natural state at depth, the behavior of clay shales is usually characterized by a strong hydro-mechanical coupling.This paper presents typical pore pressure responses monitored in different underground rock laboratories and explores alternative ways for their interpretation. The underpinning processes and their relevance are identified based on analytical and conceptual numerical models. Pore pressure monitoring data from Opalinus clay at the Mont Terri Underground laboratory, the Boom Clay at the Mol facility and the Callovo-Oxfordian clay in the Meuse/Haute–Marne URL show a similar pore-pressure response associated with stress changes accompanying tunnel construction although the tunnels were built in different rock types, at different locations, and under different in-situ conditions.The numerical analyses in this study shows that the pore pressure response around an excavation in low permeable clay shales may have different explanations. Pore pressure drops observed in the tunnel near field can theoretically be explained by both, a pure elastic response in an isotropic or anisotropic rock mass with an anisotropic stress state, or a inelastic response and related dilatancy. However, a comparison between the numerical models and the in-situ measurements revealed that the latter is more likely. This conclusion is justified by the observation that pore pressure drops occur significantly ahead of the tunnel face which is not the case in elastic numerical simulations. Pore pressure measurements in the far field, where failure processes are unlikely to occur, can only partly be explained by a linear poroelastic models. The introduction of an anisotropic material plays a key role in reproducing the responses, conceptually."

Jan 1, 2015

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By Tugba Cebeci, Bahjat Khoshaba, Bern Klein, Libin Tong, Andrew Bamber

"Sensor-based sorting technologies have potential to pre-concentrate low grade subeconomic ores through discarding the barren waste particles. However, the inability of sensors to accurately discriminate ore from waste is a barrier to prevent their wide applications. The present study focuses on the development of more intelligent sensing systems by using correlation and regression analysis of X-ray fluorescence (XRF) sensor responses on the copper ore samples obtained from Chile. The responses obtained through XRF scanning were reported both in the form of counts and the grades of elements. Linear and multiple linear correlation analyses were made between the XRF counts and the copper grades obtained through chemical analysis. Both the heterogeneity of the ore particles and the matrix effect in the XRF measurement are discussed in the study.INTRODUCTIONSorting can not only discard waste rocks away from the concentrator but also recover metal bearing ore particles that would be lost to the waste dump. The benefits of ore sorting include reduced energy consumption, water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Kleine & Wotruba, 2010; Knapp, Neubert, Schropp, & Wotruba, 2014; Kobzev, 2014; Lessard, de Bakker, & McHugh, 2014; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013). X-ray fluorescence belongs to sensor-based sorting technologies and Xrays are a high energy-high frequency form of electromagnetic radiation inhabiting the region between the ultraviolet radiation and gamma rays (Shackley, 2011). Recent XRF sorting studies on low grade copper ores were carried out at MineSense Technologies Ltd. aimed at increasing the capacity related to improving the understanding of ore heterogeneity as the basis for developing semi-bulk or bulk sorting systems (MineSense Technologies Ltd., 2016)."

Jan 1, 2016

By P. E. Cavanagh

THIS REPORT is not intended to be a ?comprehensive survey of the steel industry in Europe. For the past ten years the Ontario Research Foundation has been interested in several developments in the steel industry in Europe which it was felt would be of particular interest in Canada and might possibly find application in this country. This is an account of the present status of some of these developments. The economies of steel making in Canada are somewhat different than in the United States because of the nature of the market and the relative costs and availability of such raw materials as metallurgical coke and electric power. There are cases in Europe where a great deal of effort and money has been spent in trying to make steel profitably by methods which take advantage of locally available and cheap raw materials by modifying standard practices. ln cases wl1ere the investigations have been successful and the data are available to allow translation of the results into Canadian conditions, it is felt that such information may be of great benefit in the future in Canada and at !east should be known to all those in the steel industry in this country. The field to be covered in this report only comprises the steps from concentration and treatment of iron ores to production of iron and is only concerned with those commercially operating processes well known to us and judged to be of present interest in Canada.

Jan 1, 1957

By M. Sengupta, A. A. de Gast

"With rapid deterioration in the urban environment caused by air pollution, the possibility of chemical reaction between dimension stone and the industrial waste gases present in the ambient atmosphere remains. The chemical reaction can cause expensive damage to building stone; it is essential that a stone evaluation for use in construction should assess the possibility of this type of decay. This paper endeavours to develop testing procedures for evaluating stone decay in polluted environments. Such tests can accompany other standard tests used in dimension- stone evaluation."

Jan 1, 1972

By P. M. Dranchuk

"""PLANET EARTH seen from space appears as a fragile and limited life-supporting system in a vast emptiness. That such a view is, in fact, an accurate one is now more widely accepted than it was not long ago, before Earth's problems of over-population, overconsumption, limited resources and environmental degradation attained the limelight. The danger is that a government and public now deluged by doomsday prophecies and bemused by equally confident reiterations that technology will cure all may hesitate in coming to grips with the problem, in the hope that, given time, it will go away."" With these words, Preston Cloud begins a recent editorial, in Science(l), in which he presents a brief resume of some of the findings of the Committee on Resources and Man of the National Academy of Science-National Research Council(20.Their report, which is based on a two-year study by an extremely competent group and consists of some 250 pages of text, is even more far-reaching and sobering than the report on Energy Resources(3). It begins by quoting Sir Macfarlane Burnet as follows:""There are three imperatives: to reduce war to a minimum; to stabilize human population, and to pre-vent the progressive destruction of the earth's irreplaceable resources.(4)"

Jan 1, 1971

By J. Ita, F. Malekzadeh

"Multi-scale simulation in coupled fluid flow- geomechanical systems is a computationally efficient method for numerically solving large poroelastic systems. When using multi-scale methods, care must be taken in ensuring consistency when information is exchanged between systems that have a different discretization. Here a method is presented which provides consistency between the pore pressure being calculated on a fine scale fluid flow domain and upscaled to the coarser scale geomechanical domain and the pore volume change being calculated on the coarse geomechanical domain and down-scaled to the fine fluid flow domain. Central to this process is the characterization of the mechanical properties of the poroelastic system at both scales.Another advantage of the method presented here is that it is applicable to hydraulically disconnected but laterally drained (i.e. multi-porosity) layered systems as well as hydraulically connected, layered systems. Thus it can be used in geological situations where thin shale streaks or hardpans impede flow between laterally extensive, hydraulically conductive units. This is significant as the pressure evolution of such a hydraulically disconnected, laterally drained system can be very different than a hydraulically connected one as shown here. INTRODUCTIONA multi-scale treatment of fluid flow and deformation is a key enabler when simulation of poroelastic phenomena is limited by computational resources. As the spatial domain of the geomechanics model is usually larger than the fluid flow model, it is desireable to use a coarser discretization in the geomechanical model compared to the fluid-flow model. This type of multi-scale simulation requires a consistent up-scaling of pore pressure from the fine scale fluid flow model to the coarse scale geomechanical model and down-scaling of pore volume change from the geomechanical model to the fluid flow model (see Figure 1)."

Jan 1, 2015

By Ning Zhang, Yan Chen, Qikang Yi, Linjian Ma, Guoan Wang

Laboratory tests were performed to explore the effects of frequency on the deformation property of rock salt subjected to cyclic loading under confining stress condition. A two-stage (transient and steady) evolution law of axial cumulative strain was obtained through cyclic stress-strain curves complied from the loci of minimum load of each cycle. The unloading modulus decreases with loading cycles/time as a negative exponential function. The damage of rock salt under cyclic loading is reflected by the degradation of elastic modulus. A unified damage evolution equation considering the effects of frequency and time was established based on the experimental results. A new creep damage model for rock salt was proposed by introducing the non-stationary modular components in Burgers creep equation according to the Lemaitre equivalent strain theory. Comparative study indicates that the new model can accurately describe the creep deformation and damage evolution of rock salt under different loading frequencies. This paper provides a more reasonable model and relevant mechanical parameters for the stability analysis of compressed-air storage cavern in the injection and withdrawal durations.

Jan 1, 2015

By C. O. Stee

IN the October, 1936, issue of the Canadian Mining Journal there was published a series of very comprehensive and exccellently illustrated papers by Mr. C. O. Stee and members of his staff dealing with Siscoe operations and ore-bodies. These were, in the order in which they appeared: Geology of Siscoe Gold Mine, by O. L. BACKMAN Diesel Power at Siscoe Gold Mines, Ltd., by C. O. STEE andE. A. BLOMQUIST Mining at Siscoe, by L. T. POSTLE and W. F. Engineering and Surveying, Siscoe Milling Practice, Research and Testing Laboratory, Assaying of Mill Tails and Solutions, BROWN(6) by P. A. TEEPLE (7) by L. E. DJINGHEUZTAN by L. RIVETT (8) by G. IRWIN (9) The Editor of the Canadian Mining Journal cordially assented to our suggestion that these papers be reviewed at the 1937 Annual General Meeting of the Institute, and the authors very kindly accepted our invitation to present such reviews . Of these courtesies, full acknowledgment is here accorded. To our readers, we commend the original papers in the Canadian Mining Journal. The summaries presented at the meeting follow. EDITOR. THE GEOGLY OF THE SISCOE MINE The Siscoe gold deposits lie in and near a stock of granodiorite, related to the Bourlamaque batholith, which has intruded highly folded Keewatin volcanic rocks .. The volcanic rocks lie to the north of a belt of Timiskaming sediments.

Jan 1, 1937