Search Documents

By D. Fodor

In Romania, there are significant lignite and brown coal reserves hosted by different regions of the country. The most important lignite bearing zone of the country situated in the North ? West part of Oltenia region and which covers a surface area of 2,500 km2 and host a total reserve of 3.0 billion tons of lignite, of which more than 95% can be exploited by open cast method. The paper deals with the existing geological and mining conditions of the zone , the distribution by mining basins and exploitation perimeters, the open cast working technologies and the economic outcomes obtained throughout the time. Years ago, for the improvement of the economic situation as a whole and in each unit, a large production reorganization, technology update and modernization process was started up. There are described the rehabilitation measures of the technological lines and modernization of the equipments of the production flow-sheet, measures developed at present, too and which will still continue in future. There are mentioned the equipments considered, the components under modernization and the economic outcomes obtained so far. At the end of the paper there are presented the future actions for the equipment modernization and perspectives of the lignite deposit exploitation to meet the national economy requirements of solid fuels.

Aug 1, 2013

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By W. N. Hamilton

As a result of a test-drilling program conducted by the Research Council of Alberta in 1968, a gypsum deposit averaging 30 feet in thickness, with a chemical purity of 84 per cent gypsum, has been proven to underlie the Clearwater River valley for a distance of 18 miles at depths ranging from near-surface to 300 feet. This and other subsurface deposits in the vicinity of Fort McMurray, Alberta are the product of local hydration of anhydrite beds believed to be the water-insoluble remains of the leached Prairie Evaporite formation of Middle Devonian age, the thick salt section of which is preserved down dip. The effects of salt solution are seen in the disturbed bedding and the intermixture of greyish green shale with gypsum in the core, the shale content being responsible for the rather low chemical purity of the deposit. A similar gypsum deposit, but probably of higher purity, is postulated to occur beneath the Athabasca River valley about 60 miles north of Fort McMurray.

Jan 1, 1969

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By H. Zhu, Q. Jiang

The leaching kinetics of iron during the atmospheric direct leaching (ADL) of marmatite concentrate was studied under the following conditions: reaction temperature of 343-383 K, slurry pressure of 0.3-0.7 MPa, particle size of (-74 ?m, +63 ?m), (-63 ?m, +44 ?m), (100%-44 ?m). The statistical effects of reaction temperature, total pressure and particle size of concentrate on the extraction and the leaching rate of iron were analyzed. The results show that reaction temperature is a significant factor while slurry pressure and particle size are not statistically meaningful with respect to the extraction or the leaching rate. The extraction of iron fits better to the mixed-controlled shrinking core model and the apparent activation energy was calculated to be 37.66 kJ/mol. The leaching of iron is mixed controlled by the interfacial chemical reaction and diffusion across the product layer.

Jan 1, 2014

By Adrian Dance

The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copper-zinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products. Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance. Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of the ROM and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling. One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost and reagent consumption. Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ?equivalent?) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ?ore? becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance ? and thereby profitability ? is a powerful tool. In an operation such as Antamina, where managing ore sources, campaigns and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency.

May 1, 2003

By G. J. Kipouros, W. Judge

"The prevalent metal extraction processes for most reactive metals are fused salt electrolysis and metallothermic reduction. The feed material for both of these processes is the anhydrous chloride of the metal under consideration. Dehydration of the feed material is then a critical step in the production of most reactive metals and requires rigorous thermodynamic analysis. Thermodynamic data for most of the reactive metal chloride hydrates have not been measured. Improper dehydration of the metal chloride may lead to a prohibitive amount of hydroxychloride, oxychloride, and oxide. To prevent hydrolysis a certain pressure of hydrogen chloride is required. An estimation and prediction model is presented for the vapour pressures of reactive metal chloride hydrates in an attempt to deduce the conditions necessary for dehydration to proceed without hydrolysis. Thermodynamic data including heat capacities, standard entropies, and standard enthalpies are estimated/predicted for all conceivable intermediate hydrate compounds. Estimations are based on published data as well as trends proven in similar systems. The thermodynamic estimations and predictions are presented for the magnesium, neodymium, praseodymium, and dysprosium chloride hydrates. INTRODUCTIONThe high reactivity of metals such as the alkalis, alkaline earths, and lanthanides prevents their reduction by traditional pyro- or hydrometallurgy. In their elemental form, these metals are raw materials in the manufacture of intermediate products such as alloys and electronic components. Currently the only two viable metal production methods are fused salt electrolysis and metallothermic reduction. Various feed materials have been proposed for these processes. Using the chloride of the metal as a feed material offers advantages in separation and purity of the final product, as well as lower energy input. Chlorides, however, are hygroscopic and must be dehydrated before use. Improper dehydration will lead to a prohibitive amount of oxychloride which will lower efficiencies and contaminate the final product.Optimum conditions for proper dehydration of MgCl2•6H2O to produce pure MgCl2 without hydrolysis have been calculated from existent thermodynamic data and have been reported previously (Kipouros, 1987; 2001). Calculations were also performed for the case of production of pure anhydrous NdCl3 from NdCl3•6H2O (Roy, 1997)] and the mechanism of dehydration was elucidated. Some thermodynamic studies on the dehydration of chlorides of the rare earths have also been conducted (Sundstrom, 1997; Hong, 1997; Aschcroft, 1968; Haeseler, 1965; Ukraintseya, 1989)."

Jan 1, 2012

By G. Morin, F. Chiesa, B. Duchesne

The Quality index is a useful tool allowing to assess the metallurgical quality of aluminium AlSiMg foundry alloys (A356/357). Its value is calculated from the ultimate tensile strength and elongation; it increases with the metallurgical quality of the casting, i.e. with finer dendrites, lower microporosity and inclusion count and lower iron content. This Quality index does not depend on the degree of temper applied during the heat treatment (aging time and temperature). After defining the Quality index, it will be explained how it can be predicted from the knowledge of the local solidification conditions obtained from modelling. The paper will then present four case studies of castings for which the prediction of the Quality index by modelling was made. These case studies from different authors will involve the three most common casting processes used for producing high integrity aluminium castings, namely: sand casting, permanent mould casting and investment casting (lost wax). In all cases, the accuracy of the prediction will be assessed by comparing the predicted Quality index distributions to the experimental values based on the published measured values of the local tensile properties.

Jan 1, 2006

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By D. L. Morgan, J. A. Butterfield

"Geological data, production trends and current projects underway suggest that enough molybdenum will be available from more diversified sources to meet the world's growing demands. The growth in molybdenum consumption has been primarily related to its beneficial effects as an alloying agent in steel. This rapid growth has been deliberately fostered by stable prices, adequate supply and application research. The molybdenum industry is now in a process of change which has been seen in several other metals, such as aluminum and nickel. As supply sources have become more diversified, the market has become more competitive. The recent drop in consumption has led to excess production capacity, accumulation of substantial producer inventories and increased market uncertainties. While consumption is expected to increase in the next two to three years, it will take some time to absorb the excess capacity and inventory. The increased proportion of by-product capacity indicates that prices may become more variable. Producer discipline will be required to prevent serious price erosion in times of surplus. Future prices may not continue to increase with inflation. For the longer term, several factors favour the increased consumption of molybdenum. Engineering requirements are becoming more severe and molybdenum alloys can help to meet these changing needs. In addition, consumers can rely on a large and increasing supply of molybdenum. A 7 per cent growth rate in consumption can probably be sustained through the next decade, but new applications and reasonably stable prices will be needed to make this possible."

Jan 1, 1972

By Richard W. Hutchinson, Christopher Osterman

Abstract -The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and foot­ wall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fine grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfide piercement structures and the footwall Cu-POE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By A G. Rogers

This paper discusses the lubrication of surface and underground mining machinery and equipment from the standpoint of machine components. The machine components considered are bearings, cylinders, gears, chains, couplings, fluid drives, hydraulic systems, screws and wire ropes. The best selection of lubricants for these machine components, and for sub-divisions of the components, are outlined. They form general recommendations, for average operating conditions in both surface and under-ground mining operations. The American Petroleum Institute's service classification of both engine crankcase oils and gear oils is de-scribed and used in recommending products for these applications. The practical aspect of lubrication is kept foremost in the recommendations, which are designed to meet the requirements of a wide variety of equipment with the minimum number of lubricants. THE lubrication of mining machinery and equipment presents a variety of problems peculiar to the industry. The type of mine, the ambient temperature, water, dust, and operating and maintenance practices, as well as the age and condition of the equipment, are variables which have to be considered in making lubricant recommendations.

Jan 1, 1963

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By Morris J. Viljoen, Young. David R.

"Abstract -The zone of economic interest at H.J . Joel Gold Mine is the VS5/Beatrix Composite Reef, a quartz-pebble conglomerate of Archean age. The reef occurs at the base of the Eldorado Formation, Central Rand Group, of the Witwatersrand Supergroup. At !east three stratigraphically distinct conglomerates form this economic zone. In order of deposition these are the Footwall, Beatrix, and the VS5/Beatrix reefs. The Footwall and Beatrix reefs are equated with the Aandenk Formation with transport directions toward the northwest, whereas the VS5/Beatrix Reef is of Eldorado age, with transport directions toward the south. The change in the drainage direction was caused by a major basin-wide tectonic event that occurred prior to the deposition of the Eldorado Formation. The Beatrix Reef was formed in a proximal, braided, fluvial environment by a process of aggrading gravel bars between channelways. The VS5/Beatrix Reef was formed by the desegregation of pre-existing Beatrix Reef with the introduction of new material containing much shale detritus and is seen to have been deposited in a more ·distal, braided, fluvial environment, similar to the Beatrix Reef.The average gold concentrations are different for each conglomerate; the Beatrix at 32.1 ppm Au, the Footwall at 24.4 ppm Au, and the VS5/Beatrix at only 12.4 ppm Au. A sedimentary gold concentrating process related to higher energy braid channels was primarily responsible for these high gold grades. Not only the basal unconformity surface, but also, internal degredation surfaces, were prime sites for concentration. An understanding of the spatial distribution of these differing conglomerates and their braid channels forming the economic reef zone is necessary in predicting ore grades for future mining."

Jan 1, 1994

By K. M. Murphy, M. B. Wittrup

ABSTRACT The Saskatchewan Ministry of Environment recognizes the importance of environmental protection as an important contributor to Saskatchewan’s economy, with the environmental performance of industry closely monitored. Unfortunately, environmental regulation is often accompanied by significant process that does not always add value to environmental protection activities. The Saskatchewan Ministry of Environment has embarked on a visionary restructuring of its regulatory framework from conventional command and control regulation to a results-based regulatory framework. This new regulatory framework will provide for establishing clear environmental protection and resource management objectives; streamlining the environmental acts and regulations; developing an environmental code of practice; relying on qualified persons; enhancing compliance and enforcement tools; eliminating of many permits; and developing greater certainty in environmental assessment decisions. Results-based regulation promises to deliver enhanced environmental protection with less process. The uranium industry in Saskatchewan will be used as an example of the potential effects of results-based regulation.

Jan 1, 2012

"An unparalleled growth in the Canadian coal industry in 1970 coincided with increasing awareness by Canadians of their environment and their geography with its accompanying transportation factors. R and D on coal moved with greater emphasis toward solving problems in these areas as well as continuing with strong interest in coal preparation, carbonization, combustion, ""weathering'', spontaneous ignition, storage, exploration and geology. Long-range ""basic"" research was not forgotten in that work continued on coal-based carbons, coal chemistry and agrobiological uses for coal. This paper reviews the status of these many areas of coal research at the beginning of the seventies and takes note of some of the more significant legislation and projects brought to the author's attention. No attempt is made to itemize or to describe in detail all the worthwhile projects, many of which are reported elsewhere."

Jan 1, 1971

By H. H. Claudet

PROBABLY the first flotation mill for treating molybdenite ores was put into operation .in Norway during 1913, when the writer was employed to introduce and apply the Elmore vacuum flotation process at a mine in southern Norway. These operations proved successful and led to other similar installations in that country. It remained, however, for Norwegian engineers themselves to iron out their difficulties and establish the molybdenum industry on a basis which ultimately attained world importance. Just as today, an urgent demand for molybdenum arose during the world war of 1914-18. By 1916, many molybdenite properties were in operation in Canada and several small concentrating mills were under construction. At one of these, in the Ottawa Valley district, the opportunity came for applying the Elmore vacuum flotation process, using a flow-sheet similar to that adopted in Norway. Later, as one of the staff of the General Engineering Company, who had already developed a highly efficient flowsheet for treating molybdenite ores, using the Callow pneumatic flotation process, the writer devoted considerable time to research work and investigations on a number of molybdenite projects and deposits in eastern Canada. The bulk of Canada's production of molybdenite was coming at that time from the Moss mine at Quyon, Que., where concentration of the ore was effected by water-film flotation. It is of interest to note that this process, based on the principle of surface tension, had been developed and introduced by the late Henry E. Wood, of Denver, Colorado- one of the original owners of the Moss mine-at the time he was investigating the Elmore vacuum process in his Denver plant. The process, with certain modifications, was used at several other properties in eastern Canada, and notably in the ore dressing laboratories of the Department of Mines at Ottawa and in a plant at Renfrew, Ont., in both of which ore from deposits in various parts of Canada was treated, with recovery of very appreciable amounts o much needed molybdenite. During the summer of 1917, the water-film flotation mill at the Moss mine was dismantled and the plant was re-modelled by the General Engineering Company to include the Callow system. This installation, using improved flotation methods, was highly successful both as to recovery and grade of concentrate, and proved a decided advance in molybdenite concentration, a recovery of upwards of 90 per cent being obtained, with a concentrate grading over 90 percent MoS2.

Jan 1, 1944

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935