Search Documents

By The Staff

THE property of McKenzie Red Lake Gold Mines, Limited, consists of eleven claims located on McKenzie island in Red lake. The mine is about 4,Y:l miles by water from the Howey townsite on the same lake, and about 95 miles north of Kenora, Ont. (see Figure 4). Mail and express are flown-in daily, winter and summer, from Sioux Lookout, Hudson, Kenora, and Winnipeg. All heavy supplies are freighted-in during the summer over a water route, using four marine railway portages, from Hudson, Ont., a distance of about 180 miles. During the winter, freighting over the same route is clone by tractor if necessary, but costs are three to four rimes the summer rate. Due to these conditions, large inventories of supplies must be kept on hand, varying from a spring minimum of $45,000 to a peak of $110,000 early in November. The average cost of all freight brought in from steel during 1937 was $0.01 per pound.

Jan 1, 1938

By J. A. Abols, P. M. Grady

Recovery via gravity is one of the oldest mineral processing methods available. Unfortunately, the use of gravity techniques for gold recovery has been in decline for the past century as more effective chemical processes such as flotation and leach/CIP have been developed. Recently, with the push towards more sustainable environmental outcomes, the benefits of gravity separation have become more apparent. While gravity as a unit process is not usually capable of achieving as high a recovery as flotation or whole ore cyanidation, a combination of gravity devices alone or in conjunction with these processes can offer significant advantages to the operator. This paper reviews the range of gravity devices available, their application and the results that can be achieved by maximizing gravity through the use of a combination of gravity recovery devices. Three case studies are provided.

Jan 1, 2005

By Claude Hubert, Alex C. Brown, Pascal Marquis, D. M. Rigg

"Numerous studies of the Bousquet mining district, Abitibi, Quebec, mainly following the successive discoveries of new gold deposits over the past two decades, have led to a broad range of genetic hypotheses for their gold deposition. A compilation of petrographic, structural, and geochemical data indicates that the gold deposits are composed chiefly of pyritic schists derived from felsic and mafic volcanic and volcaniclastic protoliths, and of auriferous massive pyrite hosted by pyritic schists of felsic affinity. The deposits are typically located within zones of local pyrite enrichment and advanced-argillic alteration which are in turn enclosed within much larger zones of disseminated pyrite included in regional-scale, commonly anastomosing, zones of sericitic alteration.Overprinting relationships between three sets of folds and foliations indicate that the host-rocks of the gold deposits have retained the imprint of three successive generations of ductile deformation resulting from regional dynamothermal metamorphism. Sericitic and advanced-argillic alteration, together with massive sulphide deposition, are interpreted to have taken place prior to the onset of the ductile deformation, based on observations 1) of altered fragments of wallrocks which are enclosed within massive sulphide bodies and were thus preserved through regional metamorphism, 2) of the syntectonic deformed pyrite, and3) of the syn-tectonic porphyroblasts of andalusite, garnet and plagioclase. The orebodies are oblate to prolate, and the pyrite-gold mineralization is typically vein-type, distributed in foliation-oblique and foliation-parallel veins. The gold-bearing structures postdate all foliations, and are associated with retrograde alteration assemblages that are pseudomorphic after pea~-metamorphic porphyroblasts in host-rocks, and with cataclasticfabrics that overprint syn-metamorphic pressure-solution features and annealing fabrics in pyrite.Retrograde gold-bearing assemblages indicate a chemical disequilibrium between the ore-forming fluids and their host rocks. This disequilibrium rules out the possibility that gold was remobilized from its own host, and suggests, instead, that the ore-forming fluids and their metal contents had an allochtonous source. Stable and radiogenic isotope analyses indicate that the fluids had a metamorphic origin, and that the associated alteration took place after the culmination of the Kenoran orogeny."

Jan 1, 1990

By Adam Turcotte

Mining operations consume a considerable amount of energy, and while reduced energy consumption is desirable, it is not always clear how to achieve this goal. Understanding the opportunities to optimize energy consumption is crucial, and the key to understanding is visualization. One option is the Sankey diagram, which has been used for over 100 years to visualize the flow of energy, materials, or cost through various processes. However, there are drawbacks to this approach that must be addressed. In a Sankey diagram, each flow is represented by an arrow possessing a width proportional to the magnitude of the flow it represents. The diagrams show input flows, how energy is converted and into what form, and also output flows. As per the first law of thermodynamics, the total energy output is equivalent to the total energy input, so any energy that is not transferred to another process is considered to be wasted. These waste flows are depicted in Sankey diagrams and make it straightforward to associate energy sources, sinks and waste flows. Unfortunately, Sankey diagrams do not convey all information required to support practical decision making for redirecting individual energy flows. Based only on a Sankey diagram, it may become evident that a significant flow of waste heat is of the appropriate grade (temperature) and volume to meet an on-site heat demand currently being met with paid-for, possibly carbon intensive fuel. However without augmenting the Sankey diagram with 3D spatial, true geometric analysis, the practicalities of the concept or idea may not be fully appreciated. Another issue with a Sankey diagram is that the magnitude of the energy flowing between processes may have temporal fluctuation or variability on different timescales (diurnal, seasonal, interannual). Currently, Sankey diagrams only provide a static picture of energy conversion and consumption, so that, for example, 4 separate diagrams could have to be prepared for each season. A new energy flow visualization technique which we have called Sankey Trees has been developed. Process locations are defined within a 3D model of the site being studied, and the magnitude of the flow between each pair of processes considered is replaced with a time series. Branches of sustained and diminishing flows are represented through variation of the geometric properties of the branches of the trees. These branches are animated to indicate the direction of flow, and branch joints are used to indicate that a process is transporting one form of energy to multiple processes.

Aug 1, 2013

By A. Vasenev

The quality and durability of asphalted roads strongly depends on the final step in the road construction process; the profiling and compaction of the fresh spread asphalt. During compaction machine operators continuously make decisions on how to proceed with the compaction accounting for project specific aspects as: ambient conditions, road geometry, roller type, asphalt mixture characteristics and behavior of other machines. In discussions over quality improvement in road construction it is often suggested to robotize rollers. To operate such robots would of course require operational strategies and routines. The reality of this moment is that these operational strategies and routines are not documented. To identify the existing best working practices and, ultimately, to proceed with developing automated robotized compactors, the knowledge of machine operators should at first be explored and described in a formalized way. Unfortunately operators have difficulty verbalizing their expertise. Observation of behavior, as machine movement patterns, could be helpful to extract the operational strategies, but such observations are time and labor consuming. To overcome this burden we developed a Virtual Reality (VR) environment. In this VR environment operators perform compaction virtually, and their operational choices are traced and analysed. This paper describes this VR development and explains how it helps in following machine operators and extracting their (tacit) professional knowledge. The road geometry and the working conditions are visually represented; the operators show - rather than explain - how they would proceed with the compaction process in the given conditions. Movements of virtual machines are documented, analysed, visualised and discussed. This VR approach is expected to contribute to learning, to more formal description of operational strategies; stepping stones towards compaction algorithms for roller robotisation.

Aug 1, 2013

By E. L. Martheleur

A general expression for the electric power generated or consumed in a direct-current circuit is obtained by multiplying the reading of a suitable voltmeter connected across the terminals by the reading of an ammeter connected in the circuit. by the reading of an ammeter connected in the circuit. When alternating currents are considered, the product of the volts and amperes as obtained for direct currents does not generally represent the true energy involved; it is greater than this true energy and should be multiplied by a certain factor which may have any value between zero and unity, according to the conditions of the circuit. This factor is called the power-factor of the system, and expresses the ratio of the true energy over the apparent energy. For a three-phase system the expression of the apparent energy is [\/ 3 x E x I; ] while the expression of the true energy, that is, energy suitable for mechanical work, is [v? 3 x E x I x cos A.] The total current of a circuit corresponds to the reading of an ammeter connected in the circuit; it is the resultant of two currents. The first of these is in phase with the voltage, and is that portion which really produces mechanical work; the second is always in quadrature with the voltage, that is it may lead or lag the voltage by 90° according to the condition of the circuit. This second current does not produce any sensible work, and for this reason is sometimes called wattless current or reactive current.

Jan 1, 1924

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015

By Robert T. McKnight

"Traditional techniques for valuing resource projects companies have been primarily based on discounted cashflow methods (DCF) or by comparison to similar projects with an apparent market capitalization. Many resource projects are really forms of options to invest rather than a future cashflow stream. Employing the DCF method to value a resource project which is really an option to invest, can dramatically underestimate the real value of the project. The analytical tools required to evaluate options, while more complicated than the usual spreadsheets used for DCF, are becoming more easily available and usable by managers. This paper will discuss the background of options valuation and some of the tools which will make it easier for managers to estimate the value of projects and companies which have significant real option values.ResumeBob McKnight is a graduate of the University of British Columbia in Geological Engineering, supplemented by an MBA from Simon Fraser University. Following several years in the oil patch with Cities Service and Brascan, Bob returned to Vancouver in 1979 to work for Wright Engineers. He subsequently went on to work for Cassiar Mining, Getty Resources and Endeavour Financial before joining Pincock Allen & Holt Ltd. in 1998. His experience ranges from exploration to feasibility studies, financial evaluations of mining and oil & gas projects, due diligence, project finance, valuations and mergers and acquisitions. He has extensive international mining experience pertaining to such countries as Chile, Mexico, Uruguay, Thailand, Indonesia, Angola, Papua New Guinea, Kazakhstan.What are Options?Options have been around for centuries. They were familiar to Roman and Phoenician traders who were shipping cargoes from Mediterranean seaports. In the financial world, options are types of contracts that generally include the right, but not the obligation, to buy or sell a share, currency or commodity. The underlying commodity price or share price changes are assumed to be lognormally distributed. In this context, options are of two general types, ""call"" options and ""put"" options. Call options have the characteristic of having the right to buy a tradable commodity or currency at a predetermined price for a specified period of time. For the owner of call options, they become more valuable as the price of the underlying commodity increases. For the seller of call options, these options become an increasing liability as commodity prices rise, since there is the obligation to sell the commodity at a predetermined (perhaps lower-than-market) price. This characteristic of call options recently became high profile with the sharp rise in gold prices last year. The value of gold call options sold by certain producers increased their associated liabilities to the point where margin calls were made."

Jan 1, 2003

By L. J. Cunningham

Introduction The property of Rouyn Merger Gold Mines, Limited, is in Rouyn and Joannès townships, Western Quebec, seven miles east of the town of Rouyn. Traversing it is the east-west trending Cadillac-Bouzan fault. Diamond drilling in 1944 and 1945 along a shear zone south of the fault indicated an ore deposit lying at the contact between sedimentary and volcanic rocks and dipping approximately 60° to the northwest. In the summer of 1945 it was decided to sink a shaft to investigate the indicated ore zone. In the immediate vicinity of the deposit, bed-rock is overlain by clay beds, in some places as much as 70 feet thick. Consequently, possible shaft sites were limited to those locations where overburden would not be excessive. The most favourable site was about 125 feet to the south of the ore zone as projected vertically from bed-rock to the surface. Accordingly, it was decided to sink the shaft at this point, with an inclination of 60° N. W., paralleling the dip of the ore zone.

Jan 1, 1948

By Art Hamilton

Abstract -The Zn-Pb-Cu-Ag ore deposits of the Boundary and N-5 zones near Bathurst, New Brunswick, occur in a polydeformed volcano-sedimentary sequence that is part of the Ordovician Tetagouche Group. Massive and disseminated sulfides are hosted by an argillaceous to cherty sedimentary sequence that is stratigraphically underlain by a siliceous fragmental unit and is overlain by a feldspar-rich crystal tuff and related tuffaceous rocks. The deposits have a low iron sulfide con­ tent relative to that of most stratabound sulfide deposits of the Bathurst-Newcastle mining district. The ore is commonly associated with chlorite- and talc-rich sediments. The N-5 deposit is considered to be the fault-displaced extension of the Boundary deposit. The Boundary deposit is estimated to contain 891 000 t grading 3.310Jo Pb, 7.96% Zn, 0.32% Cu and 44 g/t Ag; the estimate for the N-5 zone is 330 000 t grading 3.24% Pb, 7.15% Zn, 0.33% Cu, and 37 g/t Ag. The ore is processed at 1000 tpd at the Heath Steele mill.

Jan 1, 1992

By DONALD E. BARNETT

Since the days of early settlement ew Brunswick has produced a variety of industrial minerals but it is perhaps only the recent discoveries of significant reserves of potash that have elevated the meaning of industrial minerals in their contribution to the provincial economy. With potash production commencing in July 1983, the role of industrial minerals will increase significantly to the value of mineral production in the province.

Jan 1, 1984

By G. B. Langford

UOCK bursts are a phenomenon about which insufficient is known. This l.~ statement has a twofold meaning. In the first place, far too many people, both inside and outside of the mining industry, are woefully ignorant of the whole subject, and secondly, as those who are face to face with the problem in the mines realize, our knowledge of rock bursts is inadequate. The first group embraces the general public, who have never been enlightened on the subject, and a great many geologists and engineers who have never shown more than a curiosity about it. Such technical men do not realize what a vital problem it is to our mining industries. They are usually thankful that bursting ground is not their problem, and leave it to those unfortunate enough to run into it. From such men one often hears the pious opinion that if proper mining methods were used there would be no problem. It is hoped that this paper will give these people a different viewpoint. Those in the second group deserve much credit for what they have done and are doing. They are fighting a large and difficult problem. In the pages that follow, I have tried to give a bird's-eye view of that problem, and suggest new ways in which it may be attacked.

Jan 1, 1941

By Erwin L. Zodrow

THE AUTHORS welcome this timely opportunity to comment o n a paper by MacLean and Merner (" Room-and- Pillar Mining at the Prince Mine of the Cape Breton Development Corporation " , ClM Bulletin , June 1978, pp. 59-62) concerning the rock falls and their relation to "a change in the strata". First, however, it is proper to express our gratitude to the Cape Breton Development Corporation, and in particular to A. R. MacLean, for making it possible for us at the College of Cape Breton to start two new collections. The first of these is a fossil plant reference collection from the Sydney Coalfield, Cape Breton (Upper Carboniferous period) , and the second is a documentation of the role o f pyrite in the formation of hydrated sulphates (samples from No. 26 Colliery, 1-B Mine, and the Prince Mine at Point Aconi). Conditions of sedimentation in the deltaic-type basin of the Upper Carboniferous time in the Point Aconi area were such that on the (coal) swamp, now represented by the Stubbart (or Hub) seam , (a) clays of varying thickness and extent were deposited , (b) biogenetic sulphur was introduced and (c) flora were buried. These are essentially the culprit s that make rock falls possible and at the same time predictable over large areas (in the present mine). The clays lithified to become shale, and biogenetic sulphur combined with iron to become pyrite (marcasite?), which exists as nodules and in fine-grained layers.

Jan 1, 1978

By Gordon S. Farnham

THIS paper summarizes the results of investigations carried out at Sydney Mines, N.S., and at Ottawa, following the disaster at Princess colliery, December 6th, 1938. The Honourable Minister of Mines for Nova Scotia appointed A. E. Cameron special investigator to enquire into and report upon the cause of the rope failure. Public hearings were held in Sydney Mines and evidence taken from many witnesses. The site of the accident was examined in detail and investigations made of the rope layout and colliery practice. At the request of the special investigator, the Department of Mines and Resources, Ottawa, kindly undertook technical and scientific examination of the broken ends of the rope. These investigations were carried out in the Metallurgical Laboratories of the Department of Mines and Resources, under the supervision of G. S. Farnham, Metallurgist for the Department. Valuable assistance in interpretation of many features of the investigation was received from other sources. Acknowledgment is due to Messrs. Stuewe, McCall, and Gordon, and other members of the staff of the Dominion Steel & Coal Corporation; to Messrs. Morrison and Scott, and other members of District 26, United Mine Workers of America; and to Messrs. Timm, Parsons, Haycock, Haanell, and other members of the staff of the Department of Mines and Resources, Ottawa, for helpful ad vice and technical assistance in assembly of information, and preparation of material and interpretation of evidence obtained.

Jan 1, 1939

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By P. C. Benedict

"The Island Mountain mine is at the southeast end of Island mountain; across Jack of Clubs lake from the Cariboo Gold Quartz mine.; The orebodies consist of quartz veins and pyritic replacement deposits in limestone. To December 31; 1944; there has been mined 296; 273 tons of quartz-vein ore averaging about 0.34 oz. gold a ton; and 101; 002 tons of sulphide ore averaging about 0.83 oz. gold a ton; a total of 397; 275 tons averaging 0.46 oz. From this; 175; 985 fine oz. of gold and about 26; 450 fine oz. of silver were recovered; having a value of $6; 510; 521.More than 95 per cent of the production has come from a band 500 feet wide along the contact of the Rainbow and overlying Baker members and extending about 100 feet into the latter. Evidence that the Rainbow belongs stratigraphically above the Baker is presented later in this paper. Both members are most variable lithologically, and individual beds and whole series of beds pinch out in short distances. In part, at least, this is due to squeezing out incidentally to intense folding. No section can be claimed with assurance to be really representative. However, both memb.ers are composed predominantly of quartzitic rocks. Both contain argillaceous quartzite, argillite, limy quartzite, limy argillite, limestone (marble), and minor amounts of highly ankeritized rocks believed to be igneous sills possibly originally approaching diorite in composition."

Jan 1, 1954

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

By R. H. Beaton

"About 1905, a plant was constructed at C1ayburn, in the Lower Fraser valley, 4'5 miles east of Vancouver, to process shales from Sumas mountain into heavy clay products. In time, mining operations were found to be more favourable on the opposite side of the mountain, and by 1913 a plant, which soon became the centre of activities, was completed at Kilgard. Destroyed by fire in 1949, the plant was rebuilt on modern lines, and a second plant was established at Abbotsford, six miles to the west. The Company, from its beginning, has grown with development of the Province. In recent years, operations have kept abreast of latest developments, particularly in materials handling. Latest innovation has been the complete conversion of fuel from Bunker C oil to natural gas. In 1957 the Company became associated with Harbison Walker Refractories, Limited, a leader in its field in the United States, and its title was changed from Clayburn Company, Limited, to Clayburn-Harbison, Limited. Currently, the Kilgard plant produces sewer pipe, agricultural tile, and flue liner; the Abbotsford plant, refractories and facebrick. Improvement of products and development of new ones are tasks of a recently-completed testing and research laboratory.Almost all ware produced is marketed in Western Canada or Washing-ton State. The Vancouver area absorbs the bulk of structural clay products."

Jan 1, 1959

By J. D. Aitken

"DEFINITION OF THE REGIONTHE REGION considered in this paper is bounded on the south by the 60th parallel, on the north by the Beau-fort Sea and Amundsen Gulf, on the east by Archean rocks or by highly deformed Proterozoic rocks of the Canadian Shield (certain weakly deformed Proterozoic strata being regarded as belonging to the Great Plains), and on the west mainly by the Mackenzie and Richardson Mountains.Only the unmetamorphosed strata of the region are considered; that is, the geology of the crystalline basement is ignored.SIGNIFICANCE OF THE REGIONThe region is significant from three points of view -namely, the economic, the scientific and the social. It constitutes 46 per cent of the area of the Western Canada Sedimentary Basin."

Jan 1, 1970