Search Documents

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By W. Tse, D. Wong

Dense medium separation (DMS) is one of several preconcentration methods used for early waste rejection from run of mine ores at relatively coarse particle sizes prior to additional milling and beneficiation. DMS has been used extensively in the coal, diamond and iron ore industries but lab scale and pilot test work has demonstrated successful separation and upgrading of other minerals such as lead, zinc, copper and lithium based ores using DMS. This paper reviews historical dense media systems, results from the pilot scale Condor DMS system as well as associated laboratory heavy liquid separation (HLS) test work.

Jan 1, 2014

By D. B. Dreisinger, M. Rasouli

"Developing technology to address the environmental hazards associated with selenium in mine-impacted waters has been a serious challenge. Ion exchange (IX) has been identified as a potential treatment technology. This paper begins with a review on selenium adsorption with commercially-available basic anionic exchangers (BAS). It then looks at the use of resins for selenium removal via modification with the addition of -O, -N, or -S-containing chelating ligands and chelating polymeric ion exchangers pre-loaded with immobilized metal cations. The synthesis of chelating exchangers requires a final product with a highly stable metal in the ligand-metal complex. The nature, oxidation state, size, and affinity of the metal for the target oxyanions and the size, degree of protonation and space configuration of the oxyanion are among critical factors affecting the oxyanion uptake. There is a limited number of studies on the critical parameters affecting the selenium affinity for chelating exchangers. Such a study could fill in the gaps of our understanding of selenium-metal-chelating ligand interactions and assist in developing a new ion exchanger. In addition to commercial IX resins, layered double hydroxide materials (LDH) have received attention for oxyanion removal from waste water. The adsorption capacity of the LDHs are affected by the crystallinity of LDH, the nature of metal components, the ratio of metals, charge and type of anion, and the space between the layers. In particular, the Friedel phase (FP), a member of the LDH family, showed high adsorption capacity for selenate removal from synthetic solution. A study is currently underway at the University of British Columbia to investigate the effect of different synthesis methods and aging on the suitability of FP for selenium removal from mine waste water."

Jan 1, 2017

"In a continuing investigation into the development of uranium alloys for armament applications, some complex base alloy corn positions were modified by varying the amount of alloying elements and by removing one or two of the alloying elements in turn from the base alloys. These uranium-base alloys were specially formulated in a search for heat-treatable, high-strength, ductile, high-density alloys. All alloys studied were ternary, quaternary or more complex alloys of uranium with molybdenum, zirconium, niobium and vanadium. Each cast alloy was studied under three different heat-treatments, and its mechanical and corrosion properties were determined. It was found that although most of the alloys studied had the hardness and strength required, they were extremely brittle and notch-sensitive under tensile stresses."

Jan 1, 1968

By Dawei Yu, Kinnor Chattopadhyay

In the nickel industry, molten slags produced from a Pierce-Smith converter contain significant amounts of valuable metals in the forms of oxides and physically entrained matte droplets. A slag cleaning step, which takes places in an electrical slag-cleaning furnace, is therefore required to recover the valuable metals as a common practice. Utilization of a waste material from aluminum industry (i.e. spent potlining) as a flux to improve the slag cleaning in terms of both the metal recovery and the operation efficiency was studied by simulation with FactSage program. Results show that the addition of SPL could substantially reduce the slag viscosity due to its fluoride values, thus accelerating the settling of matte droplets. The carbon value in the SPL could also help increase the metal recovery by reducing the valuable metal oxides followed by settling.

Jan 1, 2015

By K. Liu

"In the present work, two-step heat treatments with preheating treatments at different temperatures (175, 250 and 330°C) as the first step followed by the peak precipitation treatment (375°C/48h) as the second step have been performed in Al-Mn-Mg 3004 alloys to study their effects on the formation of dispersoids and evolution of elevated-temperature strength and creep resistance. During the two-step heat treatments, the microhardness is gradually increasing with increasing time until to a plateau after 24 hours when first-treated at 250°C and 330°C while there is a minor decrease with time at 175°C. Results show that both the yield strength and creep resistance at 300°C reach the peak values after the two-step treatment of 250°C/24h+375°C/48h. The formation of dispersoids is greatly related to the type and size of pre-existing Mg2Si precipitated during the preheating treatments, in which that coarsened rod-like ß’-Mg2Si strongly promotes the nucleation of dispersoids while finer needle-like ß’’-Mg2Si has less influence. Under optimized two-step heat treatments and modified alloying elements, the yield strength at 300°C can reach as high as 97 MPa with the minimum creep rate of 2.2×10-9 s-1 at 300°C in Al-Mn-Mg 3004 alloys, enabling them as one promising candidate in lightweight aluminum alloys for elevated-temperature applications.INTRODUCTION Due to the rapid demand from weight-sensitive automotive and aerospace industrials for the light alloys, such as aluminum alloy on the elevated-temperature applications, Al-Mn 3xxx alloys has been developed to obtain the good properties at both room temperature (RT) and elevated temperature, in which the dispersoid-strengthening mechanism plays a significant role (Li & Arnberg, 2003; Li, Muggerud, Olsen & Furu, 2012; Liu & Chen, 2015, 2015). In our previous works (Liu & Chen, 2015, 2015; Liu, Ma & Chen, 2017), the yield strength and creep resistance at 300°C of Al-Mn-Mg 3004 alloy were further improved by modifying the alloying elements, such as Fe and Mo, to optimize the characters of dispersoids, including the size, distribution and the dispersoids free zone (DFZ). For instance, Mo was introduced in aluminum alloy to further improve the volume fraction of dispersoids and reduce the area of DFZ, leading to increasing on both the strength and creep resistance at 300°C (Liu, Ma & Chen, 2017). On the other hand, the mechanical properties became worse at higher Fe content due to its consumption more Mn to form Al6(MnFe) intermetallics, resulting in less available soluted Mn for the precipitation of dispersoids (Liu & Chen, 2015). Therefore, optimizing the characters of dispersoids is always the key to improve the elevated-temperature properties of dispersoid-strengthened aluminum alloys for elevated-temperature applications."

Jan 1, 2017

By M. Muinonen, R. Pandher

Royal Nickel Corporation is developing the Dumont Nickel Project, a large nickel sulphide deposit located near the town of Amos, Québec. The nickel occurs as pentlandite, heazlewoodite, and awaruite. The relatively low grade ore can be processed to a very high grade nickel concentrate, containing 29% Ni. The absence of copper and precious metals in the ore renders this concentrate amenable to processing by dead roasting in a fluid-bed roaster and smelting in an electric furnace to produce ferronickel for sale to stainless steel producers. Laboratory test work and conceptual engineering design was completed to demonstrate the amenability of Dumont concentrate to produce ferro-nickel.

Jan 1, 2015

By P. Mišcevic, B. Kavur, I. Vrkljan, N. Štambuk Cvitanovic

It is known from earlier and recent research that mechanical properties of intact rock like uniaxial compressive strength (UCS), Young's modulus (E) and Poisson's ratio (?) are influenced by shape deviations of test specimens as deviations from the ideal cylinder. That impact can be significant at certain level of inaccuracy of specimen preparing, and it should be objectively evaluated and controlled in testing. The effects of intact specimens side straightness, ends flatness, ends parallelism and perpendicularity to the specimen axis, on UCS, E, and ?, measured in several actual ways during laboratory compression tests, were determined by previous research on 90 homogeneous specimens of limestone. In this paper, we subject these new experimental results to Response Surface Methodology (RSM) to model the mentioned dependence, to identify significant connections of variables and to evaluate the conclusions obtained directly from experimental phase. This study indicates how the responses of the model (outputs) – parameters UCS/E/??of limestone rock depend on factors (inputs) – parameters of specimen shape deviations like flatness R, parallelism P and perpendicularity O, assuming modern test machines with spherically seated upper platen. Starting from general RSM model with three factors (R, P, and O), we investigated the multiple linear regression models of specific mechanical property (UCS, E, and ?). Using the NCSS program ("NCSS 2004 and PASS 2005") in several steps, final models with very high coefficients of determination were developed for properties with the most evident effects of specimen shape deviations: nine models for strength UCS and UCS50 (equivalent UCS for specimen with 50 mm diameter), and three models for ?L (Poisson's ratio calculated from axial deformations measured on the entire specimen length). These statistical models with their response surfaces further strengthen and confirm the results and conclusions from the experimental phase. The critical values of R, P, and O are established using an additional statistical analysis to determine the lower and upper engineering limits. These findings set the basis for the new eligibility criteria for specimens of limestone (and similar rock with UCS about 100-150 MPa) in further testing of strength and deformability.

Jan 1, 2015

By S. A. Briggs

Bioremediation has been accepted as a treatment technique for groundwater contamination in subsurface soils and shows promise for contaminated fractured rock environments. Biological growth in fractured rock is expected to occur predominantly as biofilms attach to the fracture surfaces. Biofilms in rock fractures are subject to a complex system of forces and other phenomenon due to the dynamics of the bulk fluid in which they grow. In this paper, through the applications of computational fluid dynamics (CFD) to rock fractures, where the boundaries are rough and the flow is complex, a precise analysis was conducted of the interaction of a fluid flow and the rock fracture. Specifically, hydraulic parameters and velocity profiles of an actual rock fracture were calculated and compared to a fracture of equivalent aperture. From the analysis it is clear that it is important to use more complex models such as the Lattice Boltzmann Method used is this paper to describe fracture flow.

May 1, 2009

By A. Mosqueda Martinez, L. C. Trytten, R. P. Kofluk, J. J. Budac

The Corefco ammonia leach nickel refinery treats Ni-Co mixed sulphides from the high-pressure acid leaching of Moa Bay nickel laterite. Due to the low iron content of the feed, the ammonia leach process generates a leach residue with ~10% Ni+Co. Since commissioning a leach residue pressure filtration circuit in 2002, this residue has been stockpiled, dried, and sold commercially. For several years, the residue was sold to nickel smelters overseas. In 2014, re-processing of the residue in the high-pressure acid leach was tested. Lab test work was completed showing excellent extraction of the contained nickel and cobalt, and additional beneficial effects in the high-pressure acid leach circuit. A plant test in Moa confirmed the results, and preparation for shipment of the valuable leach residue for re-processing has begun. This paper outlines the test work and results, and some commercial considerations.

Jan 1, 2015

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By J. R. Porter, C. Panaou

"A significant effort is expended on preparation of the capital estimate for feasibility studies. The development of the operating cost estimate is usually allocated a significantly smaller budget and less emphasis is placed on ensuring the accuracy of the operating cost. This paper presents a comparison of capital and operating costs of hydrometallurgy processing plants in order to demonstrate the importance that variations in operating costs have on the overall life-of-mine costs. The analysis is supported by a case study on the operating costs of a water treatment plant at an existing Australian hydrometallurgy facility at the feasibility design level. INTRODUCTIONDetermination of the economic validity of a minerals processing project is a critical outcome of a feasibility study. In many cases, the financial results of the feasibility study will determine if the project should proceed to execution. Ensuring that these results are reliable and built upon sound engineering practices allows companies to make informed decisions on resource opportunities and the selected technology.The methodology for developing a capital cost estimate at the feasibility level is well established. Specialist engineering estimators use budget quotations, first principle estimation and rules-of-thumb to develop an estimate with an accuracy of typically -10% to +15%. Cost reporting software packages are used to methodically build up the estimate from design information supplied by the engineering disciplines. Risk analysis and capital expense workshops are carried out to identify potential deficiencies in the estimate. It is widely recognized that in order to successfully produce a feasibility level capital estimate with an appropriate level of accuracy, a rigorous development process is necessary.The development of the operating cost estimate is typically less rigorous than the capital cost estimate. The operating cost is normally derived by the process engineering discipline and rarely are specialist estimators used to support the development. The allocated budget for producing an operating cost is usually smaller and less emphasis is placed on ensuring the accuracy and contingency reflect the most likely operating cost scenario."

Jan 1, 2012

By W. E. MacDonald

This paper relates the story of 100 years of mining in the Harbour Seam at the Princess Colliery, Sydney Mines, Nova Scotia. Several interesting anecdotes are included along with the discussion of the evolution of coal mining methods in the area. Finally, some of the recently introduced equipment at Princess Colliery is described, and prospects for the future of the industry are outlined.

Jan 1, 1968

By A. Koster, V. Maurel, S. Dezecot, Szmytka. F.

The aim of this work is to clarify the role of microstructure heterogeneity in the initiation and growth of cracks in a lost foam cast A319 for low cycle fatigue (LCF) loading condition. Because 2D analysis fail to establish the scenario of damage events, this study is based on 3D in situ analysis using synchrotron X-ray tomography during LCF test performed at 200°C. If X-ray tomography is now an established technique to study damage development in 3D, its application for relatively high temperature cyclic tests has never been done so far. Initial 3D observations of damage show that the cracks that lead to fracture initiate near large pores and propagate into the hard particles 3D network of the eutectic regions.

Jan 1, 2015

By T. Binnert Haites

INTRODUCTION NUMEROUS examples of troubled zones, interfering with the normal development of coal seams, have been cited in the literature. From a geological point of view they can be subdivided into structural and sedimentary troubles. Of the latter type, wash-outs are usually the most bothersome. Some years ago, A. A. Thiadens and the author arrived at the conclusion that they represent fossil river-beds. A method of predicting the course of these rivers was developed, which has been successfully applied in the Netherlands coal measures, and more recently by P. Stassen in some of the Belgian coalfields and by the author in the Sydney coalfield. The Sydney coalfield has long .drawn the attention of geologists, and three main periods of systematic geological research may be distinguished. The first period, 1872-1900, is covered by the studies of Ch. Robb and H. Fletcher (32, 10-13) (1). Their detailed sections of the cliffs have lost nothing in value, and are frequently consulted today.

Jan 1, 1951

By F. Baczek, S. S. Rocks, D. Chaiko, C. Eyzaguirre, S. Asihene, T. Walters

The majority of efforts to improve primary copper sulfide leaching have focused on solution chemistry, temperature, O2 pressure, ultra-fine grinding, the use of catalysts, etc. Historically, very few studies have focused on the solid/solution interface. A new, patent pending approach to catalyzed, copper sulfide leaching has been discovered by FLSmidth that enables manipulation of the 2-D semi-conductor properties of chalcopyrite surfaces to the benefit of higher electrochemical reactivity. Copper dissolution rates are then further accelerated by incorporating a Stirred Media Reactor (SMRt) into the process. By using minute amounts of Cu2+ to "pre-activate" chalcopyrite, leach times have been reduced from >20 hours with incomplete Cu dissolution to <2 hours with 98+% Cu dissolution at 80°C. The pre-activation process takes only minutes to complete at temperatures of 80°C or less. The total atmospheric leaching process, incorporating the pre-activation and Stirred Media Reactor is compatible with existing SX/EW processes. Results of batch leach testing are presented and possible mechanisms are discussed.

Jan 1, 2015

By A. Yaghini, Y. Pourrahimian

"Human factors (HFs) play an important role in the mining and mineral industry, affecting operational and maintenance efficiency and safety. Despite the introduction of new technologies and automation in this sector, it is well known that a significantly large proportion of total human errors occur during the operation and maintenance phase. A comprehensive literature review of HFs across several industries is provided. From this review, the impact of HFs on operation and maintenance is summarized, with a focus on what the mining industry is currently doing and what opportunities exist for additional improvements. Future research directions and themes are also identified.RÉSUMÉ Les facteurs humains (FH) jouent un rôle important dans l’industrie des mines et des minéraux, en ce qu’ils affectent l’efficacité et la sécurité de l’exploitation et de l’entretien. Malgré l’apparition de nouvelles technologies et de l’automatisation dans ce secteur, il est bien connu qu’une grande partie des erreurs humaines (EH) se produisent durant une phase d’exploitation et d’entretien. Cet article propose une analyse documentaire approfondie des FH dans plusieurs secteurs. L’impact des FH sur l’exploitation et l’entretien est résumé à partir de cette analyse, une attention particulière étant accordée à l’évolution de l’industrie minière et aux possibilités d’améliorer davantage ses activités. Sont également identifiés les futurs thèmes et voies de recherche.INTRODUCTIONDuring the past several decades, the mining industry has focused on improving equipment, machinery, and methods that have led to more advanced hardware and software, equipment with higher reliability and productivity, and other technological advancements. These actions have improved safety and productivity and have reduced casualties and maintenance workload. Although today’s mining equipment and machinery are technologically advanced and highly reliable, the risk of accidents is still relatively high and key performance indicators have not improved significantly compared to other industries (Sorensen, 2012). A prominent reason could be due to insignificant integration of human factors (HFs) as part of planning, operation, and maintenance activities. The current mining system is a people system, and inevitably HFs and human error (HE) figure prominently in all aspects of this industry. Even the most advanced technologies and innovations require operators and maintainers with significant knowledge and skill, which could increase the potential for HE."

Jan 1, 2018

By M. Tadayonsaidi

The effect of alloying elements on the mechanical properties and thermal expansion of 336 casting alloy usually used as piston alloy which has low thermal expansion and very good high-temperature mechanical properties and good wear resistance was investigated. The mechanical properties and thermal expansion characteristic of samples with different combination of alloying elements, which enhance to reduce the cost of products, have been studies, The results show remarkable increase in the mechanical properties with increasing the amount of Cu and Mg, while are reduced with increasing amount of Ni, On the other hand, the use of eutectic aluminum alloy as 336 alloy with higher percent of Cu and Mg and lower percent of Ni are recommended for industry, due to economical viewpoint and satisfactory properties.

Jan 1, 2005