Search Documents

By G. R. Webber

CHEMICAL AN AL YSIS by x-ray emission spectrometry has become increasingly important during the past few years. The method is analogous to optical spectrography ?with x-rays being used instead of light and should not be confused with methods of x-ray diffraction used? for identification of minerals and chemical compounds. X-ray emission spectrometry has many advantages for both qualitative and quantitative analysis. Its optimum concentration range is higher than that of the optical spectrograph, and the group of elements which can be detected is not identical to that which can be detected by the optical spectrograph. Elements which can be detected by the x-ray spectrometer are those elements from magnesium (atomic number 12) to uranium (atomic number 92) in the periodic table. The lightest elements in this range have low sensitivities and more specialized equipment is necessary for their detection than for the heavier elements. A large number of applications of x-ray analysis have been directed toward the analysis of ores, metallurgical products, and related materials (see References at end of paper). A more complete bibliography is presented in the Norelco Reporter, Vol. 3, 1956, pp. 37-39. The periodicals Analytical Chemistry and Applied Spectroscopy are a good source of current articles and references.

Jan 1, 1957

By Ahmad Ghahremaninezhad, Rebecca Radzinski

Arsenic is a highly toxic compound that is naturally found in the environment and is released through the processing of sulphide minerals. Arsenate (As5+) is less toxic than arsenite (As3+) and is soluble in water but can form insoluble precipitates when metal ions are present. The arsenic removal processes used in industry assume that arsenic is in its pentavalent state. Hydrogen peroxide can be employed to oxidize arsenite; however, it is expensive. It has been shown that activated carbon can be used to catalyze the oxidation of arsenite with oxygen as the only consumed reagent at ambient conditions with an efficiency of 99% in less than 24 hours. The mechanism which oxidizes arsenite is not yet understood; however, this study shows that a strong oxidizing agent is formed in-situ. The species and amount of oxidant formed were determined via iodimetric titration and electrochemical methods. The production of oxidant was optimized by comparing the amount of oxidant formed in-situ to the relative amount of arsenite oxidized.

Jan 1, 2015

By Pingchao Ke, Zhihong Liu

"To overcome the problem that scoroditeis not stable in neutral and alkaline solutions, we proposed and investigated a synthesis method of scorodite coated in-situ with hydrated ferric oxide in the Fe(II)-As(V)-H2O system at the initial Fe(III)/As(V) molar ratios larger than 1.0.The synthesis was carried out at 90?,pH 1.5 under atmospheric pressure. During the synthesis, oxygen gas was conducted and bubbled into the system to oxidize Fe(II) ions into Fe(III)ions, and Na2CO3aqueous solution as neutralizing agent was added controllably into the system for keeping the pH constant at 1.5. In this study, three samples of scorodite were synthesized at the controlled initial Fe(II)/As(V) molar ratios of 1.0, 2.0 and 3.0, respectively. The characterizations of the samples by HRTEM, TEM/EDX, and chemical composition indicated that the particle surfaces of scorodite synthesized at the initial Fe(II)/As(V) molar ratio of 2.0 and 3.0 were coated in situ by a film of hydrated ferric oxide with the thickness of several nanometers, while the sample synthesized at the initial Fe(II)/As(V) molar ratio of 1.0 was uncoated scorodite. The TCLP and long-term leaching for the toxicity characteristic of the samples showed that scorodite coated in situ with hydrated ferric oxide was stable in a wide pH range from 3.0 to 10.0, with the arsenic concentrations in the leaching solutions less than 1.0mg/L. Nevertheless, uncoated scorodite was unstable under the conditions from weak acidity to alkalinity, with the arsenic concentrations in the leaching solutions larger than 5.0 mg/L.INTRODUCTIONArsenic pollution is a challenge for environment and health and has been an important issue for scientists (Hopkin, 1989).Arsenicis commonly associated with ores or concentrates of nonferrous metals, mainly as independent arsenic bearing minerals such as arsenopyrite (FeAsS), tennantite(Cu12As4S13), enargite (Cu3AsS4), cobaltite (CoAsS), and gersdorffite (NiAsS), realgar (As2S2), orpiment(As2S3), etc.(Matschullat, 2000; Mandal & Suzuki, 2002; Long & Peng, 2012). In the nonferrous metallurgical processes, arsenic is enriched mainly in such arsenic bearing materials as various flue dusts, residues, and anode slimes, which results in the accumulation of arsenic in the system owing to the circulation of those arsenic-bearing materials back to the system and the pollution to the environment (Harris, et al, 2003).In addition, the utilization of arsenic is limited and has been decreasing owing to its toxicity and carcinogenicity. Therefore, arsenic has to be removed from those arsenic-bearing materials and discarded safely (Dutrizac & Jambor, 1988; Monhemius & Swash, 1999; Drahota & Fillippi, 2009).In this case, how to immobilize arsenic has become a difficult problem which must be solved. Among the methods of immobilizing arsenic which have been proposed and investigated, immobilizing arsenic into a stable mineral to fix it, has been realized as a promising method and becomes a research focus(Dutrizac et al, 1987; Dutrizac & Jambor, 1988; Demopoulos et al, 1995; Fujita et al, 2008a; 2008b).Scorodite has been known as one of the best minerals for immobilizing arsenic, owing to its high stability under weak acidic condition, the arsenic content as high as 32wt%,and good crystallinity benefiting the separation of solid to liquid(Daivid et al, 1999; Zhu & Merkel, 2001). Scorodite can be synthesized from arsenic containing solutions under both hydrothermal and atmospheric conditions, and a lot of work has been done on the synthesis of scorodite and its leaching stability characterization (Filippou & Demopoulos, 1999; Gomez et al, 2011).Two plants for the immobilization of arsenic as scorodite have been putin to operation in Chile and Japan, respectively (Filippou & Demopoulos, 1999; Amir et al, 2016)."

Jan 1, 2017

By B. Konda, R. Lauer, D. Camilucci, D. Gladwin

"Income based taxes are significant cost elements to be considered in evaluating investment in new mine development. This paper presents the results of comparative analysis of effective income-based tax rates for mining in the Northwest Territories (NWT), selected Canadian provinces and international jurisdictions. The study was done as background to a review of royalty regulations for the NWT. ObjectiveThis paper presents results of comparative analysis of effective mining royalty1 rates, and combined effective mining royalty and income tax rates on selected mine models for the Northwest Territories (NWT), with those for several other jurisdictions in Canada and abroad which compete with the NWT for mining investment.BackgroundThe February 27, 1995 federal budget directed the Department of Indian Affairs and Northern Development (DIAND) to proceed with a comprehensive review and amendments to northern natural resource management legislation in order “to increase revenues and ensure a fair return to the Crown.” DIAND is responsible for the administration of the Territorial Lands Act, and its regulations.The Territorial Lands Act gives the Governor-in-Council the authority to “… make regulations for the leasing of mining rights in, under or on territorial lands and the payment of royalties therefor,…”. In the NWT, the Canada Mining Regulations (CMR) provide for the disposition of mineral rights for most minerals, other than coal, petroleum and related hydrocarbons, in return for the payment of a royalty to the Crown.As part of this review of the NWT mining royalty regime, several computer mine models were developed and tax regimes in a number of jurisdictions were analyzed. Effective mining royalty rates, and the combined effective mining royalty and income tax rates were compared across the jurisdictions. The results presented in this paper are a part of the background work done in preparing a discussion paper on proposed changes to the NWT mining royalty that is expected to be released for public consultation in the very near future."

Jan 1, 1997

"The outlook for Eastern Canada is decreasing coal production over the next few years; however, a reappraisal of the long-term requirements and increased prices of coal could lead to a revitalizing of the industry. The market for Western coal is expanding and is expected to exceed 50 million tons per year in the metallurgical and thermal power fields. Western coal reserves are currently estimated at 119 billion tons. Technical developments in Eastern Canada include a shearer and gate-end support system to mechanically cut the stall and brushing at the tail-end of a longwall. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Results to date on the underground hydraulic experiments exceed expectations. The importance of reclamation is recognized and plans have been made to restore and re-vegetate disturbed areas and mine dumps. In Eastern Canada, experiments were started to determine the feasibility of coal reclamation from mine dumps, including one dump that is on fire. The Mining Research Centre, Mines Branch, continued to conduct research work oriented toward solving Canadian mining problems The Western office of the Centre, opened in 1970, was set up primarily to study problems associated with a resurgent coal industry."

Jan 1, 1971

By K. Nagai

The Asian projects are now in their second terms after the five-year first terms. Ultrafined-grained steels were developed in lab-scale and/or in practical process. Basic approach has been performed to explore the evolution mechanisms of ultrafine-grained microstructures. There have been investigated two approaches to make the ultrafine grains: the "recrystallization route" and the transformation route. In the "recrystallization" route, heavy deformation at low temperature is necessary for the ultra-refinement. In the transformation route, making the high density of ferrite initiation sites in the deformed austenite, especially of the heavily compressed austenite structures, is essential for the ultra-refinement, and further hindering the ferrite growth is also inevitable to utilize the high initiation rate. Strength and toughness are dramatically improved by the ultra-refinement. Fatigue property is also excellent. The poor uniform elongation can be enhanced by the design of the second phase dispersion. At the same time the application has been also pursued from various viewpoints of engineering to take advantages of the ultrafine-grained steels. Bridge, ship, construction, automobile and other high strength parts are being attempted for the application.

Jan 1, 2004

For the last few years, a new and innovative technique has been successfully used to determine refractory and castable thickness in various metallurgical vessels. The acousto ultrasonic-echo (AU-E) technique uses stress waves to detect metal penetration and delaminations within refractory linings. In addition, it is capable of measuring the thickness of refractory layers and build-up material. The inspection and measurements can be carried out while the furnace is in full operation. The present paper discusses the principles of the AU-E technique, and its advantages and limitations. A number of case studies are presented to demonstrate various capabilities of this new Non-Destructive Testing (NDT) technique.

Jan 1, 2005

By A. Romero, M. Carvalho, D. L. Millar

"The number of underground mines replacing diesel by battery powered mobile equipment is growing worldwide. The latter produces locally zero emissions and less heat, improving air quality in the working areas, and can potentially reduce energy costs due to lower ventilation requirements and in the face of higher fuel prices. However, there is a lack of systematic approaches to evaluate the potential economic benefit of switching from diesel mobile technologies to electric ones. This paper presents a method to answer the question of whether a mine with known operating conditions should invest in battery-powered electric equipment to reduce its total costs. Furthermore, this method provides the optimal number of electric and diesel equipment in relationship with their impact on the ventilation system and the total costs of running the mine from the energy perspective. A case study of an underground mine in Northern Ontario (Canada) is presented to validate the method proposed. The scenarios studied include the specific climatic conditions of the region, and the possibility to use heat recovery for the ventilation system. Overall, results show that the use of electric mobile plants is cost competitive, especially so when electricity cost can be lowered through load-shedding strategies.INTRODUCTIONOf the multiple advantages of using electrical vehicles (EV) underground in mining, the potential increase in air quality and comfort is the most significant (Paraszczak, Svedlund, Fytas, and Laflamme, 2014). Until recently, fully battery-powered electrical underground heavy duty machinery (i.e., loaders or trucks) were not available, so that tethered and trolley assisted vehicles were the only electric alternatives to diesel powered vehicles (Bétournay et al., 2011). Today, several commercial battery-based alternatives are available (General Electric Fairchild, 2015; RDH Mining Equipment, 2015; Paraszczak et al., 2014). Operational details can be found in Ewing (2015). The main battery technology used (Lithium Iron Phosphate, LiFePO4, or LFP) was already anticipated in Bétournay et al. (2011) as a good candidate for these types of vehicles. More details on these batteries, along with state of the art and future perspectives can be found in Zubi, Dufo-López, Carvalho, and Pasaoglu, (2018)."

Jan 1, 2019

By H. J. McQueen

Friction stir welding (FSW) generates complex microstructures in the nugget and thermomechamically affected zones (TMAZ) that have led to diverse explanations. However, consideration as an extension of microstructure development in piercing/extrusion can lead to a better understanding of flow patterns and microstructures during FSW. Furthermore, the intense strains in the nugget/TMAZ can be interpreted by comparison with ultra-high strains in torsion that exhibit dynamic recovery as extending into regions with high angle boundaries strongly serrated with spacing near the subgrain size defined by the high temperature. The subgrain diameter and extrusion pressure have been shown to be dependent on the Zener-Hollomon parameter Z (=t exp(Q/RT), Q activation energy, R gas constant) combining temperature T and strain rate E in the same mariner as for torsion and compression. Moreover, such tests exhibited steady state stress os above a certain strain Es (rising as Z increases) in which T, , subgrain diameter and dislocation spacing remain constant. Due to the subgrain boundaries (SGB, low angle <5°, i.e.,LAB), continually rearranging by migration, decomposition and reformation, the subgrains remain equiaxed in elongating grains, whose boundaries (GB) become serrated as they migrate to absorb SGB. As confirmed by straining in torsion at constant T and Z. , more subgrains bordering the greater GB area have several high-angle facets (HAB) ; these small cellular regions with a mixture of HAB and LAB facets are designated HAB-subgrains. As serrations in neighboring grain boundaries impinge, the grains pinch off becoming shorter; this occurs at higher strains as subgrain size decreases with rising Z. The pinching-off makes the neighbors thicker so the grains never become thinner than about two subgrain diameters. In conjunction with such geometric dynamic recrystallization (gDRX), GB&apos;s undergo a net migration into grains with denser substructure, enlarging those with larger subgrains. Consequently a better name has been proposed: grain dimensioning dynamic recovery (gDRV).

Jan 1, 2007

By Rick Valenta

Is the Labrador Central Mineral Belt part of the IOCGU Club? ?I sent the club a wire stating, PLEASE ACCEPT MY RESIGNATION. I DON&apos;T WANT TO BELONG TO ANY CLUB THAT WILL ACCEPT ME AS A MEMBER.? GrouchoMarx Acknowledgements ?Ian Dunlop, Matt Lennox-King, Mark O?Dea, Dave Barbour, Derek Wilton, Lucas Marshall, Roland Butler, Mark King, Sally Howson,

May 1, 2006

By N. Dufresne

"The evolution of mining methods at Brunswick Mining and Smelting shows that, in the case of a large deposit, technology must adapt itself to changing conditions. As problems are encountered, management must modify their approach if they hope to meet production quotas. This search for new and better ways started with the opening of the No. 12 orebody and is still going on today.From large-scale open stoping, the Brunswick Mining and Smelting operation went to transversal cut-and-fill, then to longitudinal cut-and-fill, which is the main mining method now employed. However, to solve certain problems experimenting with Avoca methods was initiated. Rebar grouting and prepinning have also made significant contributions toward securing relatively poor ground in the hanging wall and holding badly fractured backs in wide stoping areas. Introduction In 1952, M.J. Boylen had incorporated Brunswick Mining and Smelting Corporation Limited to develop his recently found No.6 and No. 12 orebodies near Bathurst, New Brunswick. Between 1953 and 1957, St. Joseph Lead Company was brought in to try and initiate mining . During those years, St. Joseph Lead sunk two shafts at No. 12-No. 1 to 425 feet below surface and No.2 to 982 feet. They also developed the 200 and 350 levels to sample the ore at depth and operated a 100-tpd pilot plant at the No.6 mine. However, due to low recoveries and depressed metal prices. the project was shut down in 1957.A group including M.J. Boylen. K.C. Irving. Maritime Mining Corporation and Patino Corporation reacquired the property from St. Joseph Lead Company in 1961. New financing was arranged involving La Societe Generale des Minerais, S.A . of Belgium and Engineering Consultants Limited of Saint John. New Brunswick. During the years 1962 and 1963, construction of surface and underground facilities progressed rapidly."

Jan 1, 1981

By T. R. Carter, A. C. Colvine

"Rocks of the Grenville Province in southeastern Ontario are currently largely dismissed by many geologists as having little or no potential for discovery of significant deposits of metallic minerals. The present study demonstrates that the area contains numerous deposit types which elsewhere are major metal producers. Therefore, there is significant unrealized potential, especially for gold, zinc, uranium, and possibly copper.The variety of deposits of metallic mineralization include stratiform zinc in marbles; stratabound base metal sulphides in volcanic and sedimentary hosts; gold-quartz veins; quartzmagnetite iron formation; copper-nickel and iron-titanium in intrusive rocks; magnetite skarns; molybdenum in skarns and pegmatites; uranium and thorium in pegmatites, veins, and calc-silicate gneisses; hematite veins; dolomite marbles (magnesium); and barite-jluorite-celestite-galena-calcite veins. There has been significant production of iron, lead, zinc, magnesium, gold, silver, and uranium.The vast majority of the metallic mineral deposits are confined to late Precambrian supracrustal and related intrusive rocks of the Grenville Supergroup. Many of the deposits are stratiform and/or stratabound and occur within units toward the top of major volcanic successions and in the lower portions of younger carbonate-clastic sedimentary successions.Processes responsible for mineral concentration in the area include: (I) syngenetic hydrothermal activity related to both volcanism and sedimentation; (2) epigenetic processes related to diagenesis, regional metamorphism, and igneous intrusive activity; (3) magmatic processes related to igneous intrusions; and (4) supergene concentration and enrichment. The genetic classification of the mineral deposits presented is based on observed geological relationships and these interpreted geneses. The deposit types have counterparts in volcanogenic and sedimentary exhalative, Mississippi Valley type, magmatic, contact metasomatic, and lode gold deposits. Many of the exploration criteria for deposits of these types may be applicable in the Grenville Province, despite the generally high metamorphic grades and complex deformation."

Jan 1, 1985

By Marcel Vallee, Fernand Dubuc

"The St-Honoré carbonatite complex, located 8 miles north of Chicoutimi, Quebec, was discovered in September 1967 as abnormal radioactivity was detected in the course of SOQUEM's aerial surveys. The complex, covered by a shallow layer of Trenton limestone, has been explored by aeromagnetic, ground gravimetric and magnetic surveys, and 12,013 feet of diamond drilling. Its age, from potassium-argon dating, is 650 million years. The carbonatite is approximately kidney-shaped and has a surface area of 6 square miles, 20 per cent of which is explored. It shows a central core of coarse-grained massive dolomitic carbonatite and an outer ring of foliated dolomitic carbonatite.The exploration work to date has resulted in the discovery, in the foliated carbonatite, of an incompletely drilled niobium (columbium) zone of pyrochlore-bearing carbonatite, at least 1,000 by 800 feet in size. This zone contains 5,000 tons per vertical foot grading 0.86 per cent Nb205 or at least 15,000 tons per vertical foot grading 0.66 per cent Nb205 or 45,000 tons grading 0.48 per cent Nb20s. The pyrochlore contains an average of 64 per cent Nb,Os. The central core contains a zone of rare-earth-bearing carbonatite (as monazite), grading up to 4.5 per cent rare-earth oxide, 3,500 ppm zinc and 290 ppm molybdenum. Stocks of nepheline syenite and magnetite diorite accompany the carbonatite. The total analysis and trace-element contents of typical rocks are presented."

Jan 1, 1970

By R. L. Bailey

"The Acheson D-3 Pool was discovered in August 1950, and contains 88 producing oil wells on 40 acre spacing. Initial oil-in-place was 118 million stock tank barrels and initial well potentials averaged 2,000 barrels per day.In early 1956 studies of hydraulic interference between the Acheson and Leduc D-3 Pools were conducted on the Carter Petroleum Reservoir Analyzer. These studies indicated that the natural water drive to Acheson would be incapable of replacing reasonable withdrawal rates over the life of the pool. To avoid shrinkage losses a scheme of pressure maintenance by water• injection was therefore instituted in March 1957.This pressure maintenance scheme is notable because pressure is being effectively maintained by high volume injection through one well located on the flank of the pool. Close control on reservoir behaviour is maintained by regular bottom-hole pres-sure surveys and observation of water cuts on producing wells. No evidence of pressure gradients or channelling of the injected water has been observed to date, and the water-oil contact has remained level over the whole field. It is possible to control the average reservoir pressure within very close limits by varying the rate of fresh water injection.Ultimate recovery estimated from the rise of the oil-water contact and calculated water influx to December 31, 1958, is 335 barrels per acre foot, or a total of 91.4 million barrels from the pool. This compares to 217 barrels Per acre foot or a total of 59.4 million barrels indicated from laboratory test data."

Jan 1, 1961

By S. X. Shi, M. Tan, Y. Q. Li, D. F. Han, Z. B. Han

Bauxite resources in China are mainly diaspore ore with the characteristics of low ratio silicon to aluminum. In order to obtain high quality of alumina product, flotation process is generally used to extract the aluminum from diaspore ore. Small aeration rate is needed for bauxite flotation, which requires air to be controlled accuracy. In addition, productive froth from bauxite flotation is too sticky to effects froth transportation. Air-forced XCF/KYF flotation machines are helpful for aeration control, while self-suction GF flotation machines benefits froth transportation. Zhongzhou aluminum plant of China Aluminum Group (Chinalco) uses 7 series of XCF/KYF /GF combined flotation machines to process bauxite. Air distribution, suspension characteristics, froth flow velocity and Al2O3 recovery were investigated, to evaluate the performance of flotation machines in one series and determine recovery contribution of each cell to the entire flotation circuit.The air distribution degree varies from 3 to 4, which is enough for bauxite floatation process. Froth in the tank could flow smoothly with a flow velocity of 2.4m/min. The recovery of the first KYF-40 flotation cell is the largest. Flotation concentrate of Al2O3 is up to 64.29%, the total recovery is about 75%, and the ratio of Al/Si has reached 10.4.

Jan 1, 2015

By Willem P. C. Duyvesteyn

"Scandium International Mining Corp (SCY) has been involved in the commercial development of its Nyngan Scandium Project for about ten years. Various studies at a variety of global R&D organizations have been carried out in an attempt to define the deportment of scandium in both the limonite as well as the saprolite phases of Nyngan ore to assist with process development. Technologies such as sulfuric acid baking, high pressure acid leaching, sulfuric and hydrochloric acid atmospheric leaching and heap leaching have been extensively investigated both at the bench and pilot scale level to arrive at the most economic process flow sheet that will be discussed in some detail in this paper. Solvent extraction, ion exchange and other refining technologies have been tested and an optimum configuration has been established for the Nyngan project which is expected to be the first primary scandium mine and metallurgical plant in the world.Because of a lack of product availability the current scandium market is limited to less than 20 tons per year. Technologies have been identified to produce product with different specifications for aluminum alloys and solid oxide fuel cell applications. Preliminary economics have identified that Nyngan will be a robust and low capital cost project that can readily be expanded as the size of the scandium market increases."

Jan 1, 2016

By K. L. Boyd

"Can the increasing tonnages of ore and waste mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each stage of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in material handling from the mine to the mill, maximizing operating hours per year.RÉSUMÉ Le recours à des concasseurs plus grands et plus performants suffit-il à gérer l’augmentation du tonnage du minerai et des déchets que l’on extrait de nos jours ? Cet article examine les tous derniers modèles de concassage primaire et de grands concasseurs à cône. Il montre que, pour satisfaire aux exigences de production plus conséquente des exploitations minières existantes et nouvelles, il est important d’optimiser les taux d’utilisation à chacune des étapes du circuit de réduction de la taille des roches, en plus d’utiliser les concasseurs plus grands actuellement disponibles. L’objectif de cet article est d’aider les sociétés d’experts-conseils et les exploitants à sélectionner le meilleur équipement ainsi que des articles fabriqués sur mesure pour la manutention de la mine au concentrateur, en optimisant les heures d’exploitation par année.INTRODUCTIONAre larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications have since become available.The rock size reduction process from the mine to the selected milling process facility has not changed since a person first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages:• stage 1: mining (rock breakage and fragmentation);• stage 2: prescreening (scalping);• stage 3: primary crushing; and• stage 4: fine crushing (secondary, tertiary, and quaternary).Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments play a key role in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit."

Jan 1, 2017

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By E. V. Manlapig, M. A. Hampton, M. E. Holuszko

Methanol treatment of ZnS particles has been found to remove slimes and facilitate flotation. The removal of slimes renders the ZnS surface more hydrophobic, resulting in an increase in the hydrophobic attractive force between the particle and bubble. Hallimond tube flotation, induction time measurement and particle-bubble force analysis with the atomic force microscope (AFM) was undertaken to link the beneficial effect of methanol treatment of ZnS particles to their increased floatability.

Jan 1, 2009

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006