Search Documents

By E. Gaucher, D. C. Gagnon

"The paper refers to methods and concepts used in the computer treatment of banks of geophysical, geochemical and geological data, relating to the exploration of massive sulphides. In particular, a data bank of 400 drill holes on independent conductors can be used to calculate probability levels of intersecting a certain quantity of sulphides according to the characteristics of the conductor. Inversely one can, using the data bank and some cost assumptions, simulate and optimize the cost of intersecting a certain quantity of sulphides by selecting drill targets among conductors according to conductivity, magnetism or gravity. Problems of noise, inherent in any simulation, are illustrated in this paper by the results of a study of the nomenclature of volcanic rocks of 27 drill holes by forty geologists. Compilations of data banks are long and timeconsuming, and it would help to standardize to allow exchange of data. We believe that such efforts may result in the discovery of more mineral deposits and at a lower cost. The present study is supported jointly by SOQUEM The New Jersey Zinc Co. and Cominco Ltd."

Jan 1, 1973

By V. Bondarenko

The importance and necessity of gas hydrates deposits development followed by natural gas extraction is considered in the present paper. Analysis is given to world sources focused on methane hydrates formation conditions. Information covering the most perspective gas hydrate deposit of the Black Sea is presented in the article. Two most common methods of gas hydrates development ? thermo stimulation and inhibitor injection are analyzed presenting their comparative characteristics. Basic scientific trends and developments of underground mining department in the field of gas methane extraction from gas hydrates are scrutinized. Schemes and methods of natural gas hydrates development are shown together with formulas, parameters and factors influencing the extraction process. Also the analysis is given to the possibility of gas hydrates formation from methane-air mixtures of degassing wells from coal mines of Ukraine. Improved experimental unit for gas hydrates formation under laboratorial conditions is presented with its basic characteristics. General conclusions and basic tasks requiring further research are given in the end.

Aug 1, 2013

By Walter Nelson

Considerable thought and discussion had been devoted toward provision for increased milling capacity at the Allenby concentrator of The Granby Consolidated Mining, Smelting and Power Company operations as early as 1940. During the war, plans for the installation of an additional grindi.ng unit were formulated but were not carried out. It took considerable time after the war to prepare the mine again for its highest rate of production since, with the scarcity of men, development work had been sacrificed in favour of maximum ore shipments. In order to prepare for the expected competitive market in copper, the matter of increasing the capacity of the concentrator was again given serious attention. As ore became available in the mine and the output of the mill was increased, limitations for a satisfactory recovery were observed, due to the overloaded condition of the classifier units at the higher tonnages. From a metallurgical standpoint, the ore from the Copper Mountain mine had always been difficult to treat on account of the finely disseminated character of much of the mineralization and the difficulty of grinding to the desired fineness. This trouble has become aggravated with time as an increasing amount of wall-rock has diluted the ore and lower grade orebodies have been mined. It therefore has been, and is, the practice at the concentrator to maintain the maximum amount of reduction in size of material fed to the flotation units as is possible for the daily tonnage to be milled. This means that all the grinding units are operated for the maximum possible time, and that the classifiers are regulated to return as much feed ?as possible to the mills. The number of tons to be milled for ?the day is determined by the concentrator superintendent after ascertaining the availability of ore from the mine, the condition of the concentrator ore bins, and the need for repairs in the rolls plant. In order to maintain the tonnage des1red, hourly estimates are made of the rate of grinding by weighing the amount of ore contained on one foot of each of the belts conveying the feed to the various ball-mills, and adjustments are made accordingly.

Jan 1, 1950

By G. E. Agar, W. B. Kipkie, R. A. Tenbergen

"This paper describes the successful pilot plant testing of a flowsheet, developed at INCO Ltd.'s J.Roy Gordon Research Laboratory (JRGRL), for improved separation of the constituent minerals in a bulk copper nickel concentrate.The flowsheet utilized the fact that xanthate concentration on the mineral surfaces is the most important variable affecting the high lime separation and that reduction of the xanthate concentration could be effected by an oxidative conditioning stage.When the adsorbed xanthate was reduced to a suitably low level, chalcopyrite and pyrrhotite could be floated to leave a high grade nickel concentrate as the residue. Sodium cyanide was added to the froth product to depress pyrrhotite and any remaining pentlandite. The temporary depression of chalcopyrite by the sodium cyanide was overcome by introducing a conditioning step following cyanide addition. The advantages of the flowsheet; improved copper-nickel separation, operation without heating of the pulp, production of both high grade nickel concentrate ( 29. 5% Ni, . 26% Cu) and copper concentrate ( <O. 5% Ni, 30% Cu) were all realized."

Jan 1, 1984

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960

By Robert Hamilton

Aur Resources is Canada&apos;s leading copper mining company with producing mines and development projects in North, Central, and South America. Copper production from Louvicourt Mine in Quebec, Quebrada Blanca, and Andacollo Mines in Chile had a record of 245 million pounds in 2001. Located 600 km North of Montreal, Louvicourt Mine is a joint venture between Aur Resources (30%), Teck Cominco (45%), and Novicourt (45%). Aur Resources is the mine operator with 280 employees working to produce a copper and zinc concentrate. In operation since 1994, the mine has produced a total of 12,606,000 metric tonnes of ore grading 3.6 % Cu, 1.5 % Zn, 26gr./m.t Ag, 0.9gr.m.t Au. This highly mechanized mine reached full production in August 1995 at 4,000 tpd. From 1996 to 2001, the average mine production rate was more than 4,300 tpd. The Louvicourt Mine continued its record of solid performance in 2002 and is expected to continue to do so for the balance of its 2.5 years mine life.

May 1, 2003

By A. E. Cameron

The curve of coal production in Nova Scotia over the past forty years shows a definite maximum reached in 1913. Continued production to this maximum will require a greater tonnage per man-day, and this means there cannot be any increase in total man power used in the operations. There are still large reserves of coal but much of it will require washing or beneficiating to make a usable product. By-product recovery based on the present product ion is relatively satisfactory. Further development of secondary industries requires adequate markets for the bulk materials produced by the processing. It also requires access to other raw materials as well as markets for the principal product of the operations. Scientific investigation and research are needed to prove the quantity and value of lower grade or poorer quality coals, and methods for their recovery and utilization. Economics of further processing of present and future production must be investigated beforehand, if a successful development is to be assured. Such development cannot be expected largely to replace present markets. Production of coal for genera l use must continue to form the major function of the coal industry of the Province. Costs per ton must decrease, or subsidies or other assistance must increase, if the industry is to survive. Costs of investigation and research and costs of capital outlay for further development muse be met.

Jan 1, 1944

By J. Zollinger, J. R. Kennedy, J. H. Park, D. Daloz

"In order to improve the properties of cast Ti-Al alloys to replace Ni-based superalloys past the low pressure stages of aircraft engines investigations into inoculation for grain refinement were carried out. Previous work showed isomorphic self-inoculation using Ti-Al-Nb particles was effective for grain refinement, however the relatively fast diffusion of Nb in Ti-Al make it difficult to observe the mechanism of nucleation. An alternative alloy was developed in the Ti-Ta system for isomorphic self-inoculation, maximizing the Ta content to improve the particles survivability in the melt. The powder processing produced comparatively small inoculant particles which dissolved, however larger particles were seen to survive solidification. The density difference between the inoculant particles and melt resulted in an inhomogeneous mixing of the particles and the melt with larger particles found near the outer edges of the ingots. Variations on particle size and interaction time between the inoculants and the melt resulted in the Ti-Ta inoculant reducing the as-cast equiaxed grain size by a factor of two compared to non-inoculated samples as well as increasing the equiaxed fraction in the ingot.INTRODUCTION Lightweight metals are of particular interest in aerospace applications. The hot sections of turbines are dominated by blades made of nickel based superalloys. Recently the GEnx turbine introduced TiAl blades in the last low pressure stage of the turbine to reduce weight and improve fuel efficiency (Kim & Dimiduk, 1991). In order to carry these benefits deeper into the turbine the high temperature (>800oC) properties of the alloys must be improved. Current grain refinement methods to improve properties rely on boron additions which may not be applicable for all blades as brittle precipitates may be formed during processing (McCullough, Levi, Mehrabian, & Hyman, 1991). A novel grain refinement process was previously introduced called “isomorphic self-inoculation” using Ti-Al-Nb particles to successfully grain refine TiAl (Kennedy, Zollinger, Bouzy, & Daloz, 2016). In order to better understand the mechanism of this process an investigation was carried out using the same process but with a Ti-Ta alloy which is more stable in the TiAl melt than the Ti-Al-Nb."

Jan 1, 2017

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

Aur Resources is Canada&apos;s leading copper mining company with producing mines and development projects in North, Central and South America. Copper production from Louvicourt Mine in Quebec, Quebrada Blanca and Andacollo Mines in Chile was a record 245 million pounds in 2001. Located 600 km North of Montreal, Louvicourt Mine is a joint venture between Aur Resources (30%), Novicourt Inc (45%) and Teck-Cominco (25%). Aur Resources is the mine operator with 280 employees working to produce a copper and zinc concentrate. In operation since 1994, the mine has produced a total of 12,606,000 metric tonnes of ore grading 3.6% Cu, 1.5% Zn, 26 gr./m.t. Ag and 0.9 gr./m.t. Au. This highly mechanized mine reached full production in August 1995 at 4,000 tpd. From 1996 to 2001, the average mine production rate was more than 4,300 tpd. The Louvicourt Mine continued its record of solid performance in 2002 and is expected to continue to do so for the balance of its 2.5 years mine life.

May 1, 2003

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"Abstract — The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units. © 2012 Canadian Institute of Mining, Metallurgy and Petroleum. All rights reserved."

Jan 1, 2012

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By E. C. Keeley

THE property of Buffalo Ankerite Gold Mines, Limited, is in Delora township, Porcupine area, Ontario. The southwestern part of the property is ground formerly owned by Marbuan Gold Mines, Limited, which was acquired by Buffalo Ankerite in January, 1936. Until 1938, the Ankerite (or North) mine and the Marbuan (or South) mine continued as separate operations, each developed through a surface shaft and winze to the 1050 level and each having its own mill. This meant high hoisting costs, which, in 1936 and 1937, amounted to 36 cents per ton. In 1938, the underground workings of the two mines were connected on the 1050 level, and ore from both mines was hoisted at the main, or No. 2, shaft of the North mine, location of which is shown in Figure l. This shaft was discontinued at a depth of 1150 feet because, owing to the soft nature of the talc (serpentine) rock in which it was sunk, it had to be concreted throughout, and also because of its great distance--1,100 feet and 1,400 feet, respectively-from the North and South orebodies.

Jan 1, 1945

By Xiaowen (Wendy) Ma, Hans Liang, Xiaoying Chen, David Way

"The mineralogical characteristics of the process streams provide key indicators to the potential improvement in the metallurgical performance. Therefore, the process mineralogy and diagnostic metallurgy have been widely used as a tool to assist the metallurgists at the operating plants. The challenge of this study was then how to characterize the diagnostic flowsheet of the minerals of interest in the process streams across the flotation circuit. The investigation from this study indicates that the minerals chematic flowsheet can visibly demonstrate the sources that caused the gold losses during the mineral processing.In this paper, we present studies of the flotation process stream samples, representing the feeds, intermediate products, final concentrate and final tails, which were produced from the flotation concentrators of Mt Carlton mine in Queensland, Australia. This study was focused on characterizing the process streams and learns how the gold in the process streams was associated with other sulphide minerals and host minerals on a size by size basis. The automatic QEMSCAN/MLA Particle Mineral Analysis (PMA) and Trace Mineral Search (TMS) were applied to identify the minerals and to detect the gold in the sized fractions of process streams. The Laser Ablation ICP-MS (LA) spot analysis, QEMSCAN EDS spot analysis and electron microprobe spot analysis were employed to identify and quantify there fractory gold concentrations in the sulphide minerals, like pyrite, and the elemental concentrations of visible gold grains. The diagnostic flowsheet of gold recoveries by the process streams, by mineral association classes and by the particle sizes were generated and discussed."

Jan 1, 2017

By Greg Barnes

Agenda ? The Mining Stock Life Cycle ? Current Environment ? Valuation ? Golds ? Valuation ? Base Metals ? Case Study ? Quebrada Blanca Hypogene Commodity Investment Cycle ? Macro-Economic Indicators ? LME Inventories ? watch the trend; rising inventories ? bad for prices, declining inventories good for prices ? OECD Leading Indicators ? PMIs ? Purchasing Manager Indices ? Industrial Production ? more important for metals consumption than GDP ? Housing Starts ? US, Europe ? Auto Sales ? All things China ? metal imports/exports; SHFE inventories; SRB stockpiling ? Seasonality ? it does play a role ? What is Chris Dutton (TDSI Quantitative Analyst) saying?

May 1, 2010

By G. E. Wittur

"The twenty-one members of the Organization for Economic Cooperation and Development, comprising eighteen western European nations plus Canada, the United States and Japan. account for two-thirds of world steel production. The Special Committee for Iron and Steel was formed by the OECD to study trends and problems in the steel industries of member countries. The paper begins with a summary on the Organization, including an historical sketch, its structure, member-ship and objectives. The steel industry of the entire OECD is briefly described before proceeding to a more detailed discussion of various aspects of the steel industries of European OECD members, emphasizing practices and conditions that differ from those in North America. Benefits to Canada of representation at meetings of the OECD Special Committee for Iron and Steel are described."

Jan 1, 1967