Search Documents

By David R. Ray, Arthur J. Pyron, William F. Thomann

"Proterozoic plutonic and volcanic rocks in the Franklin Mountains, west Texas, exhibit similar values in average concentrations of equivalent uranium (eU), equivalent thorium (eTh) and equivalent potassium (eK) when compared to Proterozoic igneous rocks of the southwestern United States. Variations of radioelement concentrations for all Proterozoic igneous rocks of the Franklin Mountains range from 1.1 to 357.1 ppm U, 2.1to 259.1 ppm Th and 2.5 to 10.2% K.Recent geologic mapping of the Proterozoic rocks in the Franklin Mountains revealed several types of granites previously unrecognized, and these warrant further exploration for U and Th resources. Fluorite-bearing granites and riebeckite pegmatites are likely targets for further investigation, as these have the highest U and Th concentrations compared to all other granites.IntroductionThis is a summary of the paper presented at the CIM Geology Division Uranium Symposium held in Saskatoon, Saskatchewan, September 8-13, 1981. The purpose of this study was to evaluate the distribution of uranium (U), thorium (Th) and potassium (K) in Proterozoic igneous rocks in the Franklin Mountains, and compare radioelement concentrations to Proterozoic igneous rocks elsewhere in the southwestern United States.General GeologyThe Franklin Mountains are located in west Texas and southcentral New Mexico, within the southeastern part of the Basin and Range Province o f the southwestern United States. The Franklins are a complex fault-block range trending northsouth with strata dipping toward the west. Ages of the rocks range from Proterozoic to Cretaceous. Harbour (1972, 1960) provides the most recent account of the general geology of the Franklin Mountains. Most recent accounts of the detailed Pro Proterozoic geology o f the Franklins are provided by Hoffer (1976), Thomann (1980, 1981), Pyron (1980), Ray (1982) and McCutcheon (1982)."

Jan 1, 1983

By Simon Hanner

November 2005 Memorial University Newfoundland and Labrador Mines and Energy Review of Activities Exploration and Mining New Brunswick ?Université du Québec a Montréal McGill University 2005 Manitoba Mining and Minerals Convention Université Laval Quebec Exploration 2005 Saskatchewan Open House December 2005 University of Calgary University of Alberta 'Laurentian University 'Queen's University 'University of Toronto 'Ontario Prospectors Association January 2006 Mineral Exploration Roundup, BC March 2006 Prospectors and Developers Association of Canada Convention April 2006 University of Ottawa Carleton University

May 1, 2006

By Yves C. Lizotte, Malcolm J. Scobie

Blast fragmentation is affected by the physical and mechanical characteristics of the rockmass as determined by geology as well as the explosive energy, the partition of this energy, the actual amount of energy transmitted to the rockmass, the blast geometry and the detonation sequence. This paper reviews studies of the influence of geology on blast fragmentation, particularly structure, i.e. the in situ or inherent fragmentation arising from rock discontinuities. Prior structural studies have mainly been limited to comparing equivalent diameters of the in situ blocks with the size distributions of the blasted material. No criteria exist to integrate structure into blast design. This paper reviews on-going studies of the blasted fragment shape and size observed in different rockmasses aimed at analyzing geological control over blasting. Digital photoanalysis was applied {o measure size and shape distributions, to correlate results with block size distributions and shape parameters of the inherent fragmentation. An integrated and comprehensive fragmentation assessment procedure which accounts for geological control is proposed. The potential of this research is to provide a greater understanding of the true contribution of explosives to fragmentation, the effects of fragment shape on system productivity and the reduction of blast-induced damage.

Jan 1, 1994

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By D. D. Tannant, H. Ozturk

Thin spray-on liners are increasingly being used as rock support in underground mines. The adhesive strength between the liner and the rock surface is an important design parameter. Adhesion tests were conducted to assess the impact on adhesion of the presence of oil, water, and dust on a substrate, and the roughness and grain size of different substrates. Other factors such as curing time, loading rate, and liner thickness were also considered. Adhesion was measured using a pull test of a 33 mm diameter elevator bolt attached to an over-cored section of liner with strong epoxy. Most tests were performed using Tekflex liner material, although five other liner products were also tested. Adhesive strengths of about 2 MPa can be achieved with Tekflex under optimal conditions. Long-term creep tests showed that the adhesive strength could drop by at least 50% when the liner carries load for about a month. Where the rock surface is contaminated with dust or the rock is weak in tension, it may be difficult to reach adhesion strengths of 1 to 1.5 MPa. As the thickness of the liner increases, the adhesive strength to a substrate appears to decrease.

Jan 1, 2007

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By Xiaoguang Zhao

The coal mining area in Northern Shaanxi, China, has been taken as the study area, and the damage mechanism of the ecological environment is discussed on the basis of analyzing the characteristics of natural eco-environment and resource development in this area. Mining subsidence is taken as an example, and by using the Gray Correlation Analysis method, the key impact factors have been selected. An assessment model with fuzzy comprehensive evaluation has been constructed, and 12 coal mines have been quantitatively assessed. This paper also constructs an ecosystem health assessment method and index system in the coal mine area on the basis of ecosystem health theory, and assesses the ecosystem health status in the Shenfu coal mining area from 2000?2006. The research results are expected to help the eco-environment protection process in the designated coal mining area.

Aug 1, 2013

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By M. Alvarez-Silva, A. Uribe-Salas, J. A. Finch, M. Mimezami

The point of zero charge (PZC) of electrokinetically anisotropic minerals (chlorite and serpentine) was determined using the Mular-Roberts (M-R) titration technique, and compared to isoelectric point (IEP) obtained from electrophoretic mobility measurements. To validate the M-R technique, the point of zero charge and isoelectric point of two isotropic minerals (alumina and silica) were shown to be comparable. For serpentine and chlorite, respectively the PZC was found at pH 4.3 and 4.6, while the IEP occurred at pH 3.2 and <3. Settling tests showed that the maximum settling rate, which corresponds to aggregated particles, for chlorite was around pH 3, i.e., close to the IEP; lizardite did not show a conclusive maximum.

Jan 1, 2009

Open pit production planning is a procedure consisting of multiple stages. Although all the planning stages rely on the geostatistical block models, long- to short-term plans each require their appropriate resolutions and levels of details. The main motives behind using different resolutions are the tractability of the models and the practicality of the generated schedules. The current approach in the mining industry is to use nested pits generated by Lerchs-Grossman as the basis for long-term planning and to use manually generated polygons, within those pushbacks, as the units of production control in mid- and short-term planning. However, the nested pits generated by Lerchs-Grossman algorithm and the polygons drawn by mining engineer do not provide control over the value and tonnage of ore and waste inside the planning units and therefore cannot lead to optimum solutions. In this paper, we first present a pushback determination approach which maximizes the profit of the mine with control over the tonnage of ore and waste within each pushback. We then propose a clustering approach with size and shape control that determines aggregates within those pushbacks; and finally, we introduce a mathematical programming model which uses the generated pushbacks and aggregates as the planning basis and generates production schedules that maximize the net present value of the operation and are practical from the operation?s point of view.

Aug 1, 2013

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By M. H. ElMaghraby

This paper describes the development and validation of a strategy for vibration-based online detection of faults in a particular class of machinery commonly found in industry. This machinery is defined by two basic characteristics that preclude it from the application of standard online condition monitoring approaches. The first characteristic is that the machine is in a constant state of transient operation, thus making it difficult to differentiate between changes in transducer measurements that are due to variable duty and those that are due to machine malfunction or fault. The second characteristic is the fact that the machinery involves multiple sub systems that are subject to identical and simultaneous loading, operating environments and duty cycles. An example of such machinery is a system of multiple hydraulic pumps driving a common load. The monitoring strategy presented here employs an anomaly detection scheme together with methods of signal processing and feature extraction that exploit the parallel duty arrangements of this equipment. Preliminary data is collected from a pair or motor-gearbox assemblies used in a material haulage system in the mining industry. Testing and validation was performed on a mechatronic test bench with both healthy and faulted components. Experiments were carried out to investigate how various configurations of the system were able to detect different types of faults. The results indicate that this approach is effective and merits further investigation.

May 1, 2013

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

By S. Caron

From the early 70?s, ?Centre de Recherche Minérale? (CRM) has conducted and co-ordinated Research and Development activities for the mineralurgical and metallurgical industries. Since 1999, CRM has continued its mandate through COREM which is a consortium of 13 members that uses the benefits and advantages of collaborative pre-competitive industry / university research. In particular, COREM?s ?In-Situ Optimization Group? is involved in the implementation of modern optimization and control tools. The POP Project was launched in order to increase and consolidate the use of modern optimization and control tools and methods for mineralurgical and metallurgical processes. To ensure a successful transfer in the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM?s members and are grouped into three main modules: - R&D Module: Research and Development in universities, research centres and other partners; - Technology Transfer Module: integration of new tools and methods into the POP Software, industrial applications and technical support; - Training Module: education of new engineers in universities, continuing education of plant personnel through on-site workshops and resource networking by specific information exchange tools. This paper outlines the opportunities that led to the definition of the POP Project and describes its main modules. The main features of the POP Software are presented, the first application is described and finally, future developments are discussed.

May 1, 2001

By Emmanuel Henry

Hanging wall deformation monitoring at the Kiruna Mine is a major concern for Luossavaara- Kiirunavaara AB (LKAB) since underground production is deepening towards the Kiruna Town. In the quest for more effective monitoring techniques, LKAB decided to evaluate satellite-borne Synthetic Aperture Radar (SAR) interferometry?s ability to monitor ground subsidence by generating continuous deformation maps from satellite radar images. While adopted by other geoscience-related industries, SAR interferometry is still relatively untested in the Mining industry. This paper describes how subsidence is actually monitored on the Kiruna Mine?s hanging wall and gives an insight on SAR interferometry?s principle. The encouraging results are discussed as well as the technique?s benefits (continuous deformation mapping, low cost, fast, etc) and limitations (sensitivity to snow and vegetation cover).

May 1, 2003

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By H. Blaha, H. Wagner

"Room and pillar workings in salt mines are preferred sites for underground waste disposal. A critical issue in selecting waste disposal sites is long-term behaviour of such workings. The long-term behaviour of salt pillars is controlled by the pillar geometry, i.e. the height, width and length of pillars and the level of pillar stress. The latter has a strong influence on creep characteristics of salt pillars whereas the width to height ratio of salt pillars determines the strength of pillars and the deformation characteristics of salt pillars.Three different regimes of pillar creep behaviour of salt pillars can be distinguished, namely a stress level below which the rate of creep approaches a value of zero, a stress range where the rate of creep is constant and finally a stress level above which the rate of creep accelerates. Long-term stability of room and pillar workings can be assured only when the pillar stress level falls within the first stress regime. Strength and creep tests on model salt pillars have shown that at stress levels below 40% of pillar strength the rate of creep approaches a value of zero, between stress levels of 40% and 65% the rate of creep is constant but increases with stress level. Above pillar stress levels of 65% the rate of creep accelerates.Long-term measurements of pillar deformation and surface subsidence above relatively shallow room and pillar workings in salt mines have confirmed these observations. Long-term strength of salt was found that be between 60% and 65% of short term strength. The evaluation of salt pillar behaviour on the basis of critical pillar stress levels was found to be superior to the traditional factor of safety concept because it allows relating pillar deformation measurements to actual pillar conditions. The approach described in the paper was used successfully to evaluate the stability of room and pillar workings in a salt mine and to design strategies to stabilise critical pillar workings."

Jan 1, 2015

By Andrew Hickinbotham

"A water well represents not only a significant investment but also is a key to making a living or sustaining a reasonable lifestyle. This naturally makes the water well a precious possession that needsto be protected.This paper describes the challenges that TransAlta Utilities Corporation faced and how it responded to the concern of residents that open pit coal mining would affect their water well supplies.BackgroundWells have a certain mystique. Tum on the silver tap and water flows at your command without you knowing how it got there and whether it will continue to flow.Each well is different and has a story to tell. Some wells have a lot of history and are described fondly and with pride (""Grandad built this place 50 years ago and she hasn&apos;t failed us yet""). Some are passed on from father to son, some are part of the pride of good farming, some wells are famous for tapping that huge underground stream or have been mysteriously witched or have been part of a rip-off by an unscrupulous well driller. Some have to be babied so that the cows can be watered, the children can have showers and the dishes can be done. All wells represent a significant $5,000 to $10,000 investment and is a key to making a living or sustaining a reasonable lifestyle.Most wells continue to provide water faithfully - until there is a problem. For those people living next to a mine, there is the additional concern that mining has or will affect their water well supplies. Water well problems reported to the mining company have to be dealt with promptly and responsibly. The mining company&apos;s groundwater specialist must gain the trust and confidence of well owners living in the area ."

Jan 1, 1992