Search Documents

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By W. S. McDonald

PRACTICALLY all dusts derived from organic matter are explosive and instances are recorded of explosions-some of them extremely violent-having occurred in grain elevators and flour mills. While a discussion of the explosibility of dusts in general, doubtless, would be of more than academic value, it will be of greater interest, on this occasion, to consider various phases of the problems connected with the hazards arising from coal dust. Extensive and valuable research has been carried out during the past few decades on the subject of coal-dust explosions and a great part of this work has been concerned with the preventive effect of stone or other incombustible dusts. Four men have been outstanding in this very substantial achievement. The first is Dr. W. Galloway, who succeeded in demonstrating by experiments that one pound of coal dust mixed with 150 cu. ft. of air formed an explosive mixture. The next is Sir W. Garforth, who proved that stone dust is an effective preventive for coal-dust explosion. The third is G. Haon, and last but not least, L. G. Hill, both of whom laboured incessantly to produce a suitable stone-dust and a satisfactory method of application. Today, mining men all over the world are satisfied and convinced that stone dust, if properly applied, will prove effective in greatly minimizing, if not completely preventing, explosions of coal dust, as has been demonstrated in experimental mines, as well as in actual explosions, in practically every coal mining industry.

Jan 1, 1938

By R. A. Hemstock

AREAS in which the surface de-posits consist of organic material -known in some parts of Canada as muskeg and in Europe, more generally, as peat lands -have long been some of the least rewarding of lands of the north temperature zone. Even in such countries as Great Britain, Holland, and Denmark where a good deal of incentive exists to develop all available land, the use of peat land has been negligible except as a source of fuel. Only recently have efforts shown promise in re-claiming these lands for farming or for forestry. Russia has large areas of peat and use is made of it for power generation. The Russian people have also ?developed a variety of machines for handling peat, which would indicate that they are well ahead of the Wes tern World in their technical and physical ability to solve some of the problems. Certainly in Canada, where there are over 500,000 square miles of muskeg, the economic aspects of this problem are important. This is especially true in considering the shifting emphasis to northern development. Not only is muskeg in possession of great stretches of terrain, thereby rendering it useless for agricultural purposes, but it is apparently moving into forested areas and reducing their productivity. In addition, it lies as a great barrier to movement in the search for and development of such natural resources as petroleum, natural gas and minerals generally. This situation has long been recognized in Canada but only recently have organized efforts been made to study the problems and search out ways of overcoming them.

Jan 1, 1958

By P. Blonde

Recent analysis has suggested that a balanced recovery profile can improve flotation bank performance. Test work was conducted to test the balanced profile concept at the Penhorwood talc mine near Timmins, Ontario, Canada. Plant trials were devised to determine how to control the recovery profile and the resultant impact on grade and recovery in a rougher bank of four cells. Accompanying gas dispersion measurements revealed a maintenance issue with one cell that was corrected. By manipulating air and frother addition it was possible to bring the bank closer to a balanced recovery profile and the down-the-bank grade/recovery improved. Plant production showed an increased talc grade at similar yield with the balanced profile. The results provide justification for a long term plant trial.

Aug 1, 2013

By George W. Bain

The area in Quebec immediately north of the Ottawa river is underlain by a large area of granite gneiss intruded in lit-par-lit fashion into Grenville sediments and low silica intrusives of the Buckingham Series. This complex of metamorphic rocks is intruded by a much later magma found, chiefly, as a very large stock about 20 miles in diameter and extending from Brownsburg to Grenville, and as dykes and small outliers at various places adjacent to its outer margin. 1A similar stock at Rigaud, Quebec, is situated south of the Ottawa river and has been described by O. E. Le Roy. The earliest representatives of the later magma are a series of granodiorite dykes characterized by abundant hornblende, along with primary magnetite and subordinate sulphides scattered as roundish grains through anorthoclase and aligoclase feldspars and subordinate quartz. The rock is found as narrow dykes and shows no prominent secondary structures, either in the field or in thin sections under the microscope.

Jan 1, 1926

By R. W. Thompkins

In order to evaluate the impact of air quality control on mine design, a few examples are given of cases in wh.ich ventilation has affected the economics of the total design problem. Principles for the drainage of gas contaminants are shown, and the contamination control problems created by differential pressures in complicated booster fan installations are discussed. The paper also deals with the use of advanced mathematics for solving some of the ventilation problems likely to be encountered.

Jan 1, 1967

By K. E. Waters, N. Brodusch, R. Gauvin, H. Demers

"Rare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. The characterization of the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores are needed to find the optimal industrial process to extract the ores containing the rare earths. Rare earth-bearing minerals contain many elements with the M-and L-lines overlap, requiring a high degree of resolution, pushing the boundaries of scanning electron microscopy quantitative analysis. Enhanced microscopy at a high spatial resolution with improved x-ray quantitative analysis enables the accurate determination of the distribution of the desired rare earths in various mineral phases. INTRODUCTIONRare earth elements are becoming increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. From batteries (lanthanum and cerium), to magnets (dysprosium and neodymium) and lighting (yttrium), the rare earth elements are crucial to the advancement of technology, and to energy saving devices (Crow, 2011). The goal of this project is to characterize the composition, morphology and volume fraction of the various phases that have valuable rare earths in the ores in order to estimate the economical VALUES (of the ores and to find the optimal industrial process to extract the ores containing the rare earths. High spatial resolution imaging and x-ray microanalysis are needed to reach this goal. In this work, the results obtained with a cold-field-emission scanning electron microscope (FE-SEM) and a silicon drift detector (SDD) energy dispersive spectrometry (EDS) detector at low accelerating voltage are compared to experimental conditions typically used with electron probe microanalysis (EPMA) instrument.With this improvement, a detailed scientific analysis of the composition of these, and other, ores will become possible with a SEM/EDS system. This will help to better understand how such ores were formed, hence assisting in finding them, and to better understand how to process them in preparation for high end industrial applications, namely through mineral processing."

Jan 1, 2012

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By M. W. Bates, A. L. Mular

This paper, based on work carried out at Queen's University, describes the development and use of mathematical models of the parallel cyclone classifiers being used in the Strathcona mill of Falconbridge Nickel Min.es Ltd.

Jan 1, 1971

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

By W. Leblanc, J. Phalen

This paper tells the story of a serious mine fire on a mechanized longwall face in a submarine coal mine at Glace Bay, Nova Scotia. The story gives, in chronological order, a technical account of the steps taken to investigate, fight and contain the fire. The time during which the events took place spans from June 19 to November 7, 1975.

Jan 1, 1976

By Lin-fang Shen, Shao-jun Li, Zhi-liang Wang

"The meso-structure of real soil consists of numerous particles with different sizes, while the traditional reconstruction method of quartet structure generation set (QSGS) produce relatively uniform soil particles resulting in significant discrepancy between the actual structure and reconfiguration model. In order to remedy the deficiency, the QSGS is improved by considering the influence of porosity and autocorrelative function of soil, which make the models closer to the real soil. Based on the reconfiguration model, Lattice Boltzmann method is combined in the algorithm to conduct further simulation of fluid flow in soil pores. The D2Q9 model is applied to construct the two dimensional model for simulating mesoscopic seepage field of saturated soil by setting the non-equilibrium extrapolation scheme at the inlet and outlet boundary, and the bounce-back scheme at the soil particles boundary as well as the left and right boundary. According to the case study, the proposed program is realized to simulate mesoscopic seepage field of reconstructed soil with constant inlet seepage velocity. The results show that the seepage direction of soil is along the passage with good connectivity, therefore the permeability is controlled by these passages. The seepage velocity in such channels is faster than in bad connectivity channels. Even if the channel has larger pores, the seepage velocity is still small. INTRODUCTIONUnderstanding the seepage mechanism in porous materials is significant in both theoretical and engineering problems. As a typical porous media, soil consists of solid particles and voids, which form connected channels allowing water to flow through. Such seepage in soil exists widely among geotechnical project of slope, foundation pit, and tunnel, etc. Meanwhile, a number of engineering accidents are caused by limited knowledge of seepage characters in soil (Huang, 2006; Liu, 2013). The conventional method in describing seepage features mostly based on the parameter of permeability, which is a macro statistic mean evaluating the whole connectivity of soil. Obviously, this parameter cannot exactly reflect the details of how water flows through the inner soil structure, especially the flow velocity in local mesoscopic area, hence is unable to represent the actual seepage properties. Therefore, it is necessary to develop mesoscopic approaches to fully study the seepage mechanisms."

Jan 1, 2015

By Vahid Faghihi

SatraPM is a web-based software package, aiming to help project managers to easily handle their construction projects via internet. This software is capable of handling all projects of an organization, in which all projects can be defined in EPS the same as users in OBS. A 3D accessing module links EPS, OBS and inherent functions in order to provide a secure environment for the data to be processed throughout the system. This paper intends to take a deeper look at capabilities of SatraPM in helping project managers to keep track of and control their construction projects as well as its potential future features.

Aug 1, 2013

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By B. Leonard

As of November 2012, the Alberta government listed 53 oil and gas, oil sands, and mining construction projects either proposed or currently under construction. These industrial plant construction projects have an estimated value greater than 105 million dollars. A common construction method employed for industrial plant projects is fast-track construction, which is used to reduce construction time. Contractors begin fast-track construction with highly generic scheduling information. This high level schedule turns into a lower level schedule as more detailed information becomes available. From a contractor?s perspective, a challenge faced using fast-track construction is the visualization of generic and constantly changing project schedules. This paper discusses the use of a Plant Information Modeling (PIM) system, designed to create a 4D animation to visualize project schedules for fast-track industrial plant construction projects. The proposed PIM system creates a modified project schedule by obtaining specific information from a generic construction schedule. Obtaining the information involves grouping schedule activities in accordance with the level of detail in a 3D model, and the level of detail in a project schedule. The modified project schedule is then used in conjunction with a 3D model to simulate the construction sequence in the form of a 4D animation. This allows for 4D visualization of project activities, installation dates, and crane movements. Furthermore, as engineering reaches completion, the PIM system creates a streamlined channel for schedule information updates to be easily uploaded into the model for a more accurate 4D visualization. Through analyzing a nonmodular construction case study, this paper discusses the successes and benefits of the PIM system for 4D visualization, such as increased productivity, shortened construction time, increased constructability, and decreased field costs.

Aug 1, 2013

By L. H. Smith, D. S. Taylor

"AbstractSherritt has been applying hydraulic drives to concentrator equipment since 1967. The initial application was made on a bank of 5- by 5-in. slurry pumps. This has now been extended to all slurry pumps requiring less than 40 hp and several conveyors which require variable-speed or low-speed/high-torque characteristics. The pump motors are directly connected through a flexible coupling, whereas the conveyor systems are directly mounted onto the head-pulley shaft extension.The different applications and design concepts will be described, with outlines of the operating and maintenance advantages and disadvantages and costs. The paper also outlines future possible applications, together with the limiting conditions, of such systems.IntroductionSHERRITT GORDON MINES LIMITED has been operating a mining division in Northern Manitoba for almost 50 years. The original mining operation was at Sherridon, Manitoba and was a copper-zinc producer. This mine was exhausted in 1948 and the mining plant was moved north to its present location at Lynn Lake, Manitoba. The Lynn Lake Mine is a nickel-copper producer. Since 1960, two new mines have been discovered and brought into production in the general vicinity of Lynn Lake. The first of these was the Fox Mine, a copper-zinc property operating at 3,000 tons per day from an underground operation. This mine started production in May 1970."

Jan 1, 1977

By W. W. Beaton

The Coxheath copper mine is situated on the north side of the Coxheath hills and opposite the French Vale, at a distance of about 10 miles southwest of Sydney, Cape Breton county. The deposit was discovered in 1880, and the first work on the property was carried out with local capital. Lacer some Boston men became interested and formed a Company to finance the undertaking. This group operated the mine intermittently for approximately 20 years, spending close to one million dollars on the undertaking. Three shafts were sunk to depths of 110, 190, and 340 feet, and further underground workings to the extent of approximately one-half mile were driven. Also, an extensive surface programme was carried out. in which many test pits and hundreds of feet of trenches were dug, Early in the summer of 1928 the Arno Mines, Limited, optioned the property and immediately started an exploration campaign. A series of trenches were dug along the parallel vein system, and over 4,000 feet of diamond-drilling was done. The results obtained were so encouraging that a mining plant was erected in the fall of chat year and No. 2 shaft was drained. A complete new plant was installed, consisting of one 120 h.p. Fairbanks-Morse Diesel engine, direct connected to a Sullivan angle compound, air compressor; an 80 h .p. Leonard boiler, which supplies power for the 7 by 11 Ingersoll-Rand hoist; and a Sullivan class C steel sharpener and oil furnace. Two 250-gallon Cameron pumps, one operated by steam and the other by air, were placed in the mine so that, in case of a break-down, the mine would not be flooded.

Jan 1, 1930

By C. H. Lee, T. T. Wang

"Exampling of the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, this study investigates the application of the Drilling Survey System (DRISS) in both Drilling and Blasting (D&B)- and Tunnel Boring Machine (TBM)-excavated sections. In the D&B section, a nonlinear relationship exists between drilling energy and uniaxial compressive strength of rock mass, in which a reasonable coefficient of determination can be analyzed statistically. Additionally, the DRISS accurately predicted an unfavorable section with a valuable position. The magnitude of uniaxial compressive strength back calculated using DRISS data also matches those acquired from geological investigations with different approaches. Study results indicate that the DRISS is an effective tool for fore-probing of both D&B- and TBM-excavated tunnels. INTRODUCTIONModern advancements in geological and geophysical investigations, and drilling techniques, have provided valuable information for detecting and interpreting geological conditions of rock tunnels with a resolution of several to ten of meters (Brückl et al., 2001, 2008, Lorang et al., 2005). Nevertheless, construction risks remain considerable during tunnel excavation, especially when a tunnel was excavated by a Tunnel Boring Machine (TBM). Predictions of the local fault, shear zone, and other minor geological features, which may cause moderate collapse or excessive deformation of rocks surrounding the tunnel, before tunnel excavation is highly desirable for high-quality tunnel construction and economically efficient project management.Rather than conventional geophysical prospection methodologies, which always favor large-scale investigation with moderate precision, this study focuses on the drilling method probing ahead of a tunnel. The goal of such an investigation is not only to prevent catastrophic collapse, but also to provide quantitative or semi-quantitative information for estimation of the mechanical parameters of rock mass.For the tunneling task in the Tsengwen Reservoir Transbasin Diversion (TRTD) in southern Taiwan, a drilling survey system is adopted for fore probing. Data collected from both drilling and blasting (D&B) and TBM-excavated sections are analyzed statistically and discussed. The applications of the Drilling Survey System (DRISS) are addressed accordingly."

Jan 1, 2015

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By Thomas G. Madgwick

Introduction Development of oil and gas is still centred in the Province of Alberta, much as it was when C. C. Ross read a paper on this subject three years ago at the Annual General Meeting in Montreal; but so far as gas is concerned, its early production in Saskatchewan seems now assured. The three years that have elapsed since Mr. Ross' paper have witnessed a growth in the world's production of oil that has created a potential supply out of all proportion to the demand for petroleum products, and one that has resisted the most energetic efforts of the industry entirely to control. The natural result has been very much to retard the active prospecting of new structures in the Prairie Provinces with any immediate view to oil production, although the same factor has not hindered the search for gas to the same extent. One consequence has been to divert the attention of organized oil operators from wildcat drilling to more detailed geological investigation than had hitherto been customary, sometimes accompanied by test drilling with a view to the elucidation of geological structure rather than to the immediate development of production which at the present is not needed. Nevertheless, in spite of the growth of this phase of oil prospecting - which the writer would be the last not to welcome as a very real blessing and of far greater value than indiscriminate wildcat drilling in either the complex structures of the foothills or the simpler but largely concealed formations of the plains- it is most satisfactory to have to record that in these three years the growth of production both of naphtha and the heavier crude-oil has kept pace with the by no means inconsiderable growth in the production and utilization of natural gas.

Jan 1, 1929