Search Documents

By A. F. Matheson

"The Jellicoe is the most westerly mine in the Little Long Lac area with a record of gold production. The property is largely covered with overburden and the ore deposit was found by diamond drilling along the projected strike of a gold bearing zone at Magnet lake 1 ½ miles to the east on the property of Bankfield Consolidated Mines, Limited. In 1940-41 Jellicoe mined the whole orebody of approximately 14,000 tons, recovering 5,620 ounces of gold.The vein is in light-coloured greywacke. A mile-long dyke of fine-grained quartz feldspar porphyry 5 to 10 feet in width lies 100 feet south of the vein. A similar, even longer dyke lies 700 to 800 feet north of the vein. Some narrow diorite dykes are also rather closely associated. The porphyry dykes are gold bearing, but not ore. The vein material is quartz and silicified and brecciated greywacke. Mineralization consists of native gold, pyrite, arsenopyrite, and some sphalerite."

Jan 1, 1954

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

The dynamic breakage process of rocks by the impact of a hydraulic hammer is more complex than one normally assumes. It is even more difficult when one has to conduct the breakage under water. In such cases one does not know exactly what the surface topography and composition are at the bottom of the sea or river and, hence, it is more difficult to select the best position of the hammer before starting the hammering. Typically, an industrial hammer has a diameter of about 250 mm, a length of about 1.25 to 1.75 m and a mass of several tons. The hammer frequency can be up to 50 impacts per minute. The general principles of rock hammering can be easily summarized, but this knowledge is not sufficient to adapt adequately the method for less common rock conditions (e.g. less brittle rock, presence of vertical and subvertical fractures, etc.). That is the reason why we initiated a research project, whereby a scale model has been developed to conduct experiments in the laboratory and whereby discrete element simulations are being conducted. Both aim at a better understanding of the basic mechanisms of rock hammering. The scaled experimental model allows varying the impact energy and the static weight independently. Within the experiment, the hammer is in contact with the rock specimen under a certain confining pressure and with a certain contact pressure due to the static weight. A weight falls on the hammer, creating the dynamic action or impact; the height over which the weight falls can be varied. The penetration is recorded after each impact. After a certain penetration the test is stopped and the internal crack patterns are described. Some simulations have been conducted, allowing the modeling of individual fracture initiation and growth during the penetration of the hammer by either a constant displacement rate (using the UDEC-code) or by introducing the dynamic process (using the PFC-code). Some of the observed features in the laboratory experiments can be visualized in the simulations. However, further research is needed to allow the simulations being an adequate tool to well understand the dynamic process in laboratory experiments, as well as the in-situ behavior.

Aug 1, 2013

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By G. Danko, C. Lu

"High temperature and humidity at the working negatively affect safety and health in deep and hot underground mines. It is necessary to predict during design the dynamic changes in temperature with heat and moisture emitted into the mine ventilation-thermal-humidity (VTH) system from various sources such as auto-compression, wall of strata, mining equipment and workers. Currently available mine ventilation and climate models are either furnished with a simplified, step-change-type (SCT) model for thermal solver (such as in Climsim, VnetPC, Minevent, MFire, etc), or with more advanced models to account for the “thermal history effect” (also known as thermal flywheel effect), such as in Ventsim and MULTIFLUX. The goal is to quantify the modelling error caused by the lack of variable thermal history component in the SCT model. Two models are compared: one with and one without the thermal history component in long, single airway examples with long-term climate simulations for 20 years assuming an input air temperature with daily variation. The examples illustrate the magnitude and the time-lag phase of the variation of the modelling errors with space, time and model conditions. Large errors are shown in the order of +14°C and –7°C errors, persistent for long time periods, up to 20 days in one example.INTRODUCTIONIt is important to predict the heat and humidity distributions during the design of hot and humid underground mines for the safety and health of the workers. The feasibility of extracting a rich deposit in great depth may depend on the extent of ventilation and mine climatization for maintaining an acceptable working environment. The cost of ventilation and cooling may be substantial, up to 40–50% of the total energy cost of mining (Clausen, 2017). The accuracy of model solution is important in view of the low profit margin in mine feasibility for deep and hot mines. Safety and health of the miners, the primary concerns, are therefore inherently connected to finding ever better solutions in simulation methods and ventilation control techniques."

Jan 1, 2019

By M. G. Lipsett

"Mining properties are becoming increasingly remote, a challenging situation for operating and maintaining equipment. Logistics of transporting workers and materials can be alleviated by having timely, accurate information of equipment location and operating condition, and by automating some activities. This paper discusses an infrastructure for remote operations, with strategies for communicating different types of data, and a design method so that systems can interact with either an operator or another system. A remotely operated excavator prototype is described, with on-board performance and diagnostic monitoring systems now used on production equipment. IntroductionSyncrude Canada Ltd. operates an openpit oil sands mine near Fort McMurray, Alberta. For twenty years, draglines and bucketwheel reclaimers have fed conveyors that transport dry oil sand to an extraction and upgrading plant. In converting to a truck and shovel operation, Syncrude has developed slurry pipelines and bitumen froth pumping to allow more remote leases to be mined more than 30 km from the base plant.There are organizational and resourcing challenges in operating and maintaining equipment in three nearby, but separate, mines. The logistics of transporting workers and materials to production and support equipment become more difficult, and operations and maintenance personnel and facilities become more distributed. Supervising mine operations will rely even more on having timely, accurate information about equipment location and operational status.Syncrude is typical of an open-pit operation. Voice communications are the preferred way to exchange information for making immediate decisions about operations and maintenance. A large number of narrowband FM broadcast radio channels keep teams of miners working together. Haul truck drivers, shovel operators, and dispatchers talk on one channel while maintainers coordinate activities with the control tower on another. Cellular phones have become popular for supervisors who have to talk with planners and engineers in offices without radios."

Jan 1, 2000

By John J. Barakso

A summary of geochemical dispersion processes is presented. Secondary and tertiary dispersion of uranium was examined at several uranium prospects in British Columbia. The vertical migration of uranium from bedrock (primary dispersion) through overburden into the various soil horizons, and into snow and plants, was studied, and relationships were sought to explain the dispersion patterns in the secondary and tertiary environments. Soil developments were examined to obtain information on factors affecting the dispersion of uranium in soil profiles and tertiary substances; samples were analyzed for a number of elements. Biogeochemical data indicate that plant geochemistry is a possible exploration aid in areas of heavy overburden owing to the high selectivity of certain plants for specific elements. Some new data on the geochemistry of snow are discussed as a matter of research interest in the tertiary dispersion of uranium. Analytical techniques and problems are discussed, particularly extraction techniques, which must be carefully chosen to give reliable information on uranium dispersion.

Jan 1, 1979

By Chris Dougherty

"This presentation will provide a demonstration of the methodology used in designing a modern shaft and hoisting plant utilizing a review of the challenges faced and solutions delivered for the Elk Creek Superalloy Materials Project (Niobium/Scandium). The development of the design required the review of complex hydrogeological conditions, mine production requirements, demanding capital expenditure (CAPEX) limitations and tight schedules. Through an extensive review of various alternatives to satisfy these constraints, the Nordmin Group (including Nordmin Engineering Ltd.) (Nordmin) was able to define a concept and design that addressed risks to the project, met production requirements, cost and schedule constraints and improved constructability. INTRODUCTION The Elk Creek Project, owned by NioCorp Developments Ltd. (NioCorp) presently, will become Nebraska’s first underground metals mine, built to access the Elk Creek Niobium/Scandium deposit. The development of the design for this facility required the review of challenging hydrogeological conditions, mine production requirements, demanding CAPEX limitations and tight schedules. Through an extensive review of various alternatives to satisfy these constraints, the Nordmin Group was able to define a concept and design that addressed risks to the project, met production requirements, cost and schedule constraints and improved constructability. This paper will review the challenges faced, and solutions arrived at in a demonstration of a methodology used in designing a modern shaft and hoisting plant. THE CHALLENGES Nordmin became involved in the project in 2015, invited by the Feasibility Study Consultant to provide input on estimating and layouts for the new operation. Many of the fundamental decisions regarding mining methodology, water handling and production strategy had been made, and the scope of Nordmin’s involvement was very limited in this first engagement. Following submission of that study in late 2017/early 2018, Nordmin had opportunity to discuss the overall effort, and its many assumptions and challenges, with NioCorp’s project team. The dialogue quickly identified several significant opportunities to improve the project construction schedule and costs along with the mine production profile and operational approach while reducing project risk."

Jan 1, 2019

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By Unknown

With the present-day trend of rising labour costs and a lowering of production efficiency of workmen, it has become imperative that every effort be made to use manpower to the greatest advantage and to mechanize mining as much as possible. During the past few years this trend has gained much prominence in the Porcupine camp. In view of this, the executive of the Porcupine Branch considered that the Mechanical Movement of Muck would be a very timely subject for a Symposium. Accordingly a Committee was formed, with A. K. Douglass, Mine Superintendent for Delnite Mines, Ltd., as Chairman, and the Symposium was held in the Auditorium of the McIntyre Community Building, Schumacher, on March 25th last. Papers dealing with shovel loader and mechanical scraper operation at six of the larger mines of the camp were presented and discussed, and a tabulation was prepared giving data on the machines in operation at a total of eleven mines. The papers and tabulation, reproduced below, will doubtless be of considerable interest to operators of mines in all parts of Canada.

Jan 1, 1948

By M. P. Tixier

Abstract In a review of the application of electrical logging in Canada, examples are .given of long and short distance correlations by means of the electrical logs. The use of MicroLogging for the determination of permeable and porous formations is explained. The question of log analysis for the quantitative determination of fluid saturation and porosity is .discussed. An example is provided to illustrate the significance of the resistivity gradient. The advantages of the new method of the Laterolog are shown, chiefly for the case of wells filled with high-salinity mud. Introduction Electrical logging techniques developed rapidly in Canada at the time an intensive drilling activity started for the exploitation of the Devonian series in Alberta, namely, at the beginning of 1947. The conventional service was soon thereafter supplemented with the latest technica1 improvements. Canada has been among the first regions to take advantage of MicroLogging*, which has proved a most powerful .tool for the investigation of permeable and porous formations; also, the more recent development known as the Laterolog has ?been introduced in Canada. The Laterolog provides a better determination of .the formations, particularly in the case of salty mud where the conventional logging is greatly handicapped. The various methods of electrical logging are now commonly known in oil industry and have been described in numerous publications ( 1) ( 2) (3).

Jan 1, 1951

By K. Esmaieli

This paper addresses issues associated with ore pass degradation caused by material impact. A series of numerical experiments, using the particle flow code, were undertaken to investigate the influence of various finger raise configuration. This has allowed the identification of favorable configurations. The results of this analysis, when coupled with field observations, can contribute to the design of ore pass systems that can prolong the useful operating life of ore pass systems.

May 1, 2009

By John A. C. Fortescue

There is a need for better communication between scientists who plan and carry out mineral exploration research in glacial terrain and the exploration geologists who look for mines. In this paper, four ways in which workshops could be used to close this communication gap are described and discussed in relation to the solution of this problem in Canada.

Jan 1, 1973

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By Gerald Blackmore

This paper discusses the present state and future trends within the coal industry, and then goes into the reasoning behind these planned trends. Such factors as marketing, costs, new mining techniques and machinery, and manpower and human resources are considered. Finally, the author refers to the effect that these trends will have on the coal industry of Cape Breton.

Jan 1, 1968

By S. Manning, W. Morris

Mineral exploration assessment file information has long been considered a useful resource for developing mineral exploration strategies, and one of the most common data sets fled in assessment reports is ground magnetic surveys. The new Earth Resources and Land Information System database (ERLIS) now provides a method for rapidly accessing all references to a specific area through a series of raster images. The ERLIS provides access to the Assessment File Research Imaging (AFRI) database which comprises geo-science mineral exploration assessment file data, Mineral Deposits Inventory (MDI), together with provincial aeromagnetic data from the Ontario Ministry of Northern Development and Mines(MNDM). Conversion of the raster images of ground geophysical data to vector data files together with the concatenation of grids from adjacent claims provides a method for constructing high resolution magnetic regional images. The value of this resource is demonstrated through the construction of a single composite magnetic image derived from eight assessment file grids for an area south of Kirkland Lake, Ontario, within Pacaud and Catharine Townships. The composite grid of magnetic data provides a map with resolution that is not achieved by currently available Ontario Geological Survey airborne data sets. Details contained within the new high resolution image, permit the differentiation of lithologies and their boundaries, fault orientations and the location of alteration zones with magnetic response.

Jan 1, 1997

"The asbestos mining industry in the Eastern Townships of Quebec has early recognized the undesirable side-effects associated with mineral production, such as air pollution, noise and unsightly waste dumps. In order to efficiently achieve the industry's aim of eliminating or minimizing these objectionable features of mining, all of the asbestos producers in Quebec interchange information, knowledge and design dealing with the environmental control measures through the Environmental Committee of the Quebec Asbestos Mining Association.The paper describes what has been done and what is planned for the future in the various problem areas, such as control of dust emitted during the open-pit drilling operation, control of dryer stack emissions, control of the environment in ore, fibre and tailings handling operations, rehabilitation of the countryside covered by waste dumps, and many others."

Jan 1, 1971

"Block caving is the preferred underground mining method to profitably extract massive, low-grade orebodies; however, lack of cave access inhibits understanding the rockmass response to mining, which is needed for safer, more productive operations. Combining large datasets from multiple sources with virtual reality scientific visualization (VRSV) is an alternative method for understanding complex cave behaviour, by providing virtual access to the cave. A customized VRSV module was developed at UNSW Australia to investigate rockmass response to undercut developments at a case-study block caving operation. Time/sequence effects are investigated in rockmass response to blasting, which is an important factor in hard-rock mines.RÉSUMÉ La méthode d’extraction souterraine par blocs foudroyés est la méthode préférentielle pour extraire rentablement des gisements massifs à faible teneur. Toutefois, le manque d’accès à la chambre restreint la compréhension de la réponse de la masse rocheuse à l’exploitation, ce qui est nécessaire pour obtenir des opérations plus sécuritaires et plus productives. La combinaison de grands ensembles de données de multiples sources avec la visualisation scientifique par réalité virtuelle (VRSV) constitue un autre moyen de comprendre le comportement complexe de la chambre en fournissant un accès virtuel à la chambre. Un module de VRSV sur mesure a été développé à l’Université de Nouvelles-Galles du Sud (UNSW) en Australie afin d’étudier, dans une étude de cas d’une exploitation par blocs foudroyés, la réponse de la masse rocheuse aux développements de galeries de sous-cavage. Les effets de temps/séquence sont étudiés dans la réponse de la masse rocheuse au sautage, ce qui est un facteur important dans les mines de roches dures."

Jan 1, 2016

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By Graham Sim

Agenda ?The Water Challenge ?Examples from Three Case Studies ?Mine Drainage, 99% recovery ?Mine Drainage, 80% recovery ?Road Dust Control ?Technology Development ? Conclusion Global water challenges Assuring sustainable quantity Improving water quality Reducing energy consumption

May 1, 2011