Search Documents

By M J. Noy

The automated measurement of rock fragmentation particle size distribution in the muck during muck excavation has been developing over the last 16 years. The introduction of stereo camera imaging of the muck has provided improved automated particle segmentation for image-based measurement algorithms. Recently, a new vision system processing algorithm has been developed. The inclusion of 2D texture in the analysis has provided a significant improvement in the definition of the finer size fractions, which has resulted in the automated analysis no longer requiring calibration.The previous stereo vision system algorithm required analysis calibration to account for poor ‘small particle’ definition in the 3D surface profile. This was because of the depth perception limitations of the stereo camera system at greater than 8 m. The new algorithm has been implemented on a number of shovel-installed vision systems, and the algorithm’s performance in automated analysis has been assessed against a diligent manual analysis of the same fragmentation images. The new algorithm provides improved distribution resolution and accuracy.CITATION:Noy, M J, 2015. Evaluation of a new vision system algorithm for automated fragmentation measurement from a shovel, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 721–726 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Higgins

Measurement while drilling (MWD) techniques can provide a useful tool to aid drill and blast engineers in open cut mining. By avoiding time consuming tasks such as scan-lines and rock sample collection for laboratory tests, MWD techniques can not only save time but also improve the reliability of the blast design by providing the drill and blast engineer with the information specially tailored for use. While most mines use a standard blast pattern and charge per blasthole, based on a single rock factor for the entire bench or blast region, information derived from the MWD parameters can improve the blast design by providing more accurate rock properties for each individual blasthole. From this, decisions can be made on the most appropriate type and amount of explosive charge to place in a per blasthole or to optimise the inter-hole timing detonation time of different decks and blastholes. Where real-time calculations are feasible, the system could extend the present blast design even be used to determine the placement of subsequent holes towards a more appropriate blasthole pattern design like asymmetrical blasting.

Jan 1, 2001

By M D. Griffith

Oct 12, 2022

By R M. Yanamandra, S K. Tripathy, N Mangadoddy, P Sudikondala, P Ankireddy

Spiral concentrator is one of the most commonly used gravity concentration devices in mineral processing. The particles are classified based on their specific gravity and size. The present work analyses the experimental and numerical investigations of the water flow field, such as fluid depth and free surface primary velocity of two high gravity spiral concentrators at different flow rates. The measurement techniques use a flow depth gauge and flow visualisation technique adapting lycopodium powder as the tracer. Flow features in terms of liquid depth and primary velocity at the free surface of the flow are captured across the trough in two different high gravity spirals. A highspeed motion camera with an imaging frequency of 5400 frames per second and 768 × 768 pixel resolution is utilised to track the tracer particles in the liquid flow on the dark surface background. Further, the two-phase flow is studied numerically on high gravity spirals based on the volume of fluid (VOF) approach utilising the RNG k-ε model and Reynolds Stress Model (RSM) for predicting the fluid flow on trough surfaces such as water depth and free surface primary velocity. The CFD predictions of the flow field for the two spirals are attempted to validate against experimental data. The high gravity spiral concentrators show lower flow depths and free surface primary velocities but steep velocities on the outer trough zone compared to that of low gravity spiral concentrators (conventional coal spirals). Among the computationally tested high gravity spirals, higher pitch and higher secondary slope design shows greater flow characteristics.

Aug 24, 2022

By A Whaanga, W Vigor-Brown

IGO Ltd’s (IGO’s) Nova-Bollinger Deposit (Nova-Bollinger) is a magmatic nickel-copper-cobalt (NiCu-Co) sulfide deposit found 160 km east-north-east of the town of Norseman in Western Australia (WA). The deposit is hosted by the Mesoproterozoic rocks of the Fraser Zone, which is part of the Albany Fraser Orogen (AFO). Since mining commenced in 2016, IGO’s Nova Operation (Nova) has mined and processed to 31 December 2020, 5.63 Mt of ore grading 2.04 per cent Ni, 0.86 per cent Cu and 0.07 per cent Co. Nova’s mine geology team (MGT) has used commercially available implicit modelling (IM) and general-purpose resource modelling (RM) industry software systems, to prepare the 31 December 2020 (CY20) update of Nova-Bollinger’s JORC Code reportable Mineral Resource estimate (MRE). This CY20 MRE update was predominantly based on ~386 km of diamond core drilling, with the drill holes having a nominal grid spacing of 12.5 by 12.5 m throughout the mineralised zones of the deposit. Using IM tools, Nova’s MGT interpreted and modelled 22 separate domains from the drill hole logging, assaying results, and the MGT’s underground mapping. These IM closed volumes were then used to control the estimation of MRE variables into conventional industry digital block models using RM and other ancillary software systems. During 2021, a commercial machine learning (ML) software was trialled by Nova’s MGT for preparing block models of Nova-Bollinger’s MRE domains. The motivation for the trial was that the ML process could expedite modelling through the direct creation of a domain coded block model from the drill hole logging. Compared to the industry standard approaches of wireframing or IM, where the modeller usually makes many subjective choices to produce the domain model, ML offers a more objective ‘hands-off’ process for determining the connectivity of domains defined in drill holes. Additionally, the ML process provides a quantitative confidence metric associated with its output that may have utility in mine production and resource classification. In this paper, the results of the Nova-Bollinger ML modelling trial are compared to the MGT’s current workflow for MRE work. The MGT’s conclusions as to the advantages and disadvantages of the IM and ML methods for preparation of MRE domains are discussed. The ML software was also tested as a method of rapidly interpreting geology outside the principal zones of MRE interest. These testing results are also presented in this paper.

Mar 22, 2022

By C Beal, S Singh

Sensor-based bulk ore sorting is a form of preconcentration that autonomously measures and physically separates discrete bulk ‘pods’ of run of mine (‘ROM’) or primary crushed material. This case study examines the results of a full scale bulk ore sorting trial undertaken at Cozamin mine in Zacatecas, Mexico in 2019. The bulk ore sorting plant comprised primarily of a mobile jaw crusher, fixed conveyor, MR analyser, and diverter gate. Results of the trial demonstrate that bulk ore sorting could deliver a net improvement in copper metal fed to the processing plant of 6-8 per cent within an equal gross tonnage of ore. Copper metal increases were the result of improvements in mining recovery, where valuable mineralisation is recovered from marginal or sub-grade material that would otherwise be discarded as waste or stockpiled as low-grade. The increase in mining recovery more than compensates for metal losses suffered in the bulk ore sorting plant.

Nov 10, 2020

By D Flint, K Vague

The Work Health and Safety Act 2020 (WA) (WHS Act; DMIRS, 2020) and associated Work Health and Safety (Mines) Regulations 2022 (WA) (WHS Regulations; DMIRS, 2022), supporting guidance materials and other laws, such as the Sex Discrimination Act 1984 (Cth) (SD Act), have imposed new duties on every person or business conducting an undertaking (PCBU) in Western Australia, including those operating in the mining industry. These laws and associated guidance materials combine to require owners, operators and contractors to discharge positive duties and better report and manage psychosocial hazards in the workplace. For mine operators, there is a positive duty to not only identify and eliminate hazards relating to psychological harm, sexual harassment and gendered violence at work, but to also report incidents to the safety regulator that could result in serious harm, even while internal and police investigations are ongoing. Traditional mines safety teams are navigating the evolving frontier of psychological and gendered safety as the duties relating to psychosocial safety and sexual harassment at work continue to expand. This paper will review the legal obligations on PCBUs to conduct internal investigations into critical psychosocial incidents and gendered violence on mines, whilst balancing the demands and sensitivities of investigations by the safety regulator and police. There are emerging approaches to safety investigations that can aid PCBUs in managing their investigations of psychosocial incidents and gendered violence, including trauma-informed investigation techniques, collaboration with psychological experts and the use of limited legal privilege. Well managed and sensitive investigations can foster trust amongst workers, result in improved incident reporting by workers and lead to enhanced safety outcomes for the resources industry whilst preserving the legal positions of involved PCBUs. Specifically traversing the new duty to consult, cooperate and coordinate, this practical session will arm mine managers, safety professionals and human resources professionals, from mine operators and mining contractors alike, with tools and processes to bring to safety investigations, particularly on residential mine sites.

Apr 16, 2024

By M Taylor

The Project Specification and Technical Requirements documents associated with several recent large road tunnel projects within Australia have specified the application of AS/IEC 61508 – FunctionalSafety of Electrical/Electronic/Programmable Electronic Safety Related Systems at very high performance levels for the various control and fire life safety systems associated with such facilities.This paper seeks to explore the implications of referencing this standard within the road tunnel services context in terms of practicality, complexity and cost, whilst providing some examples of how a high safety integrity level (SIL) level can theoretically be achieved given current hardware availability.

Mar 8, 2011

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

By D Deb, R Pramanik

This paper presents a generalised methodology in smoothed particle hydrodynamics (SPH) framework to analyse dynamic failure process of rock mass having natural joint under blast-induced stress wave and expansion, and penetration of high pressure gaseous product. The necessary interactions of gas-rock are incorporated in the model which describes features of coupling between damage and plasticity in tension and compression respectively. A Drucker-Prager formulation of plasticity is used to model the behaviour of aggregate field and the Grady-Kipp damage model is employed for tensile strain. These two material behaviours are then brought together within the framework of interacting continua. The model relies on the Drucker-Prager plasticity surface to predict the dilatancy aspect of the material response and to account change of strength according to the strain rate effect. Three numerical examples are presented with rock joint and multiple blastholes.CITATION:Deb, D and Pramanik, R, 2015. Smoothed particle hydrodynamics modelling of blast-induced fracture processes in naturally jointed rock medium, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By W Zirima

A detailed, mine scale non-linear numerical model of Rosebery mine has been built for the purpose of simulating life-of-mine global deformations. The model was calibrated using observations of displacement and damage, and was then used to investigate the correlation between dissipated plastic energy (DPE) and seismic event occurrence. The study is unique because the seismic data was collected over a relatively short period using a temporary portable seismic system. It is the intent to undertake significantly more work, but the analysis of limited data shows that a very good, non-linear relation between DPE and event probability is present. The observed correlation is consistent with measurements from other mines where more data was available. With more data, the strength of the correlation will allow the DPE analysis to be used during the design and sequencing phase of planning to better design the mine to minimise seismic hazards.

Jan 1, 2008

By R M. Stephenson

Large diameter raise boring is a common raise excavation method in the Australian mining industry. Geotechnical investigations were conducted on several large diameter raise bore projects at Gwalia Mine to assess the potential for instability and potential back-reaming problems. A thorough geotechnical analysis and subsequent back-analysis was conducted on a vent raise excavated at 5.5 m diameter and 810 m length.The geotechnical investigation for the vent raise included collection of data from an acoustic televiewer survey that was conducted on the pilot hole. The survey results provided structural data and an insight into the effects of stress on the pilot hole. Structural analysis was conducted using a combination of information obtained from the acoustic televiewer survey and geotechnical logs of the diamond drill core drilled close to the site.Further information was collected from drillers’ plods from pilot hole drilling and back-reaming to conduct a back-analysis of the completed shaft, and this was compared with the structural analysis.The key finding from this review was that the acoustic televiewer survey of the pilot hole accurately identified locations with blocky conditions. This is an important supplement to the information available from the main geotechnical investigation hole, as this was offset from the shaft location over most of its path.CITATION:Stephenson, R M and Sandy, M P, 2014. Structural analysis of acoustic televiewer logs for large diameter raise bored shafts, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 89–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A Roshal

It is anticipated that many future uranium mines in Australia will be using the in situ leaching mining process. It is fair to say that close to one third of uranium production will be generated by this method, whilst the other two thirds will fall on the uranium generated from hard rock mining and other mining methods, such as traditional open cut mining. For other types of deposits the in situ leaching mining method will remain the best technological, commercial and environmental alternative. It is important to identify and prevent all risks involved in uranium mining. The expertise in this subject is limited. Over the years there was only one mine using the in situ leaching process for uranium extraction in Australia. Computer simulation of propagation of leachate during and after the uranium in situ leaching is a crucial factor, not only for addressing the environmental concerns, but also for the most efficient recovery of the deposit. The decontamination can be modelled for a period of up to 100 years, with the acid neutralisation forecast for a period of up to 400 years. The results of the modelling are paramount for definition of the reserves, efficiency of the mining method and the environmental impact statement. The accuracy of the hydrogeological modelling and carefully selected environmental management program enables a mining company to quantify and minimise the impact of the mining activities on the regional aquifer and to prevent environmental disasters. In the study, the completed hydrogeological model allowed the client, the authorities and the community to make an informed decision about the environmental impact of the in situ leaching of uranium. In particular, the model proved that neither during the mining, nor during the neutralisation the toxic elements would interact with the local catchment area.

Jan 1, 2008

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D A. F Oliveira, C J. Parker

The role of the virgin in situ stress field in tunnelling projects is well known in the Sydney area. The effect of in situ stresses is mostly considered through the use of published relationships that describe the in situ stress conditions as a function of depth. Considering the significant scatter in the data, it is evident that by adopting such relationships, the designers are assuming an average distribution of stresses with depth that is generally a reasonable engineering approach; however, when building a geomechanical model, the tunnelling or geotechnical engineer needs to account for the interrelationship between ground conditions (rock mass quality – fracturing, strength and stiffness) and in situ stress, which may explain part of the stress data scatter. This paper presents an alternative approach for interpreting in situ stress conditions, valid for both Sydney sandstones and shales that focus on such interrelationship between in situ stress and ground conditions.CITATION:Oliveira, D A F and Parker, C J, 2014. An alternative approach for assessing in situ stresses in Sydney, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 189–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By B W. Atkinson, J Docherty

An Australian Working Group has been compiling a guide for operators to use in order to improve the efficacy of their routine and non-routine sampling tasks within their coal preparation process. The guide focuses on unit operations within the process, and not conveyor belts or transfer stations that are adequately covered by the existing Standard ISO 13909.Representative sampling of unit operations is generally an after-thought following plant construction, whether that be a result of oversight, or more commonly, capital cost minimisation during initial construction. Minimising capital cost by avoiding adequate sampling systems is generally a poor decision, since the result is a process that cannot be adequately measured, meaning that it cannot be adequately managed and optimised.The use of the term ‘guide’ rather than ‘standard’ is intentional. Practical means of sampling unit operations within existing plants generally relies on a compromise between sample representativity (minimisation of bias) and sampling feasibility. The guide does not endorse poor sampling practice, but instead offers practical guidance to overcome, to the extent reasonably possible, real-life limitations.When it comes to sampling any particular process, it is almost always necessary to make a professional judgement as to whether or not the proposed samples are likely to be sufficiently representative such that the sampling will be worthwhile. Such judgement needs to be exercised by personnel who understand the principles of sampling, as they apply to the stream being sampled. There are many circumstances where available methods for sampling of a particular stream will be meaningless, and in such circumstances analytical data from that sampling will only serve to propagate poor decision-making.This paper outlines the approach for the guide, the areas it covers and the approaches adopted for different types of unit operations and associated equipment configurations.CITATION:Atkinson, B W and Docherty, J, 2017. A practical guide to sampling in coal preparation plants, in Proceedings Eighth World Conference on Sampling and Blending , pp 241–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B Jones, M Chappell

Permanent rock bolts used to support rock tunnels are required to perform for the design life of the structure as a minimum. Quality of installation is critical to the performance over the life of the rock bolt.This paper will present the findings from an in investigation into the integrity of rock bolts installed in an underground hydroelectric power station cavern and access tunnel. The 25?mm diameter rock bolts were installed 50 years ago, tensioned and post cement grouted. Due to a major machine upgrade the whole facility was subject to an asset survey. The owners are responsible for managing the risks associated with the failure of these rock bolts and ensuring the structural integrity of the tunnels and caverns is maintained to continue operations, protect machinery, assure production and more importantly maintain a safe working environment for all employees and visitors.To help manage risk a proactive approach is desired. To this end a test schedule using a non-destructive testing (NDT) system was carried out by Independent Integrity Testing Pty Ltd (i2t). The system used in this application was RokTel™. The system operates by applying a small axial impact to the rock bolt end and measuring the resultant acceleration response. The rock bolt characteristics affect the acceleration response.The data output from the system is analysed principally using Fourier Analysis (FFT) and sinusoidal waves. The energy generated in the bar, the rate of damping and changes in frequency are all assessed. Testing was carried out on 70 rock bolts within the tunnel and cavern. A selection were then over cored, photographed and documented. The data gathered from the testing is then correlated with physical evidence to establish a calibration for the remainder of the rock bolts and assess if this is a viable method for identifying defective elements, and what degree of accuracy can be achieved. The findings will assist with the future assessment of similar hard rock underground?facilities.CITATION:Jones, B and Chappell, M, 2014. The use of non-destructive testing to identify defective rock bolts – a case study, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Salu, G J. Kay

"As underground mines increasingly face the challenge of maximising production without losingfocus on safety excellence, the ability to predict the eff ectiveness of mine seals and stoppings andthe identifi cation of defects plays an increasingly important role in mine ventilation management.While technologies for sample testing installed seals provides signifi cant assurance, the difficulty of conducting tests in operational environments, combined with the production impact of destructive testing procedures, has led to the development of a new method for non-destructively testing ventilation control devices (VCDs). This paper addresses the challenges of in situ testing and reviews the approaches previously employed to verify the quality of VCD installations. It then describes a new testing methodology jointly developed by Whitfield Minerals PTY Ltd and Parsons Brinckerhoff (PB) and the range of tests that have been carried out in the laboratory, above ground, at trial underground sites and in active coal mine operations. Although this is a new approach to testing underground VCDs, the method employs recognised testing equipment in a new application. The aim of the new non-destructive technology is to not only verify the thicknessand therefore overpressure rating compliance, of new VCDs, but to allow mine operations t oidentify and locate defects in installed VCDs without causing damage to the material structure.Currently it is difficult, time-consuming and costly to carry out physical sampling and testing ofevery VCD. Therefore, a reliable and accurate means of non-destructively testing concrete andplaster seals in situ will provide substantial operational and safety benefi ts to the underground coal mining industry."

Jun 1, 2012

By T G. Vizcarra, B Wong

Optimisation projects are regularly undertaken without knowing the root cause of an issue. It is all well and good to trial a multitude of flotation reagents, change the operating characteristics of your flotation cells, or add more media into your ball mills, but time and again, root cause analysis traces issues back to the performance of hydrocyclones. In JKTech's experience, hydrocyclones are poorly operated and maintained (in both primary grinding and regrind circuits), exacerbating issues that many operations commonly experience.Recent case studies are presented where JKTech has been engaged to improve the process only to discover that the hydrocyclones were the main issue. At one operation it was found that the hydrocyclone feed density gauge was reading significantly lower to the actual density. Following re-calibration of the gauge, and with further improvement of cyclone operational and design parameters using JKSimMet, a significantly sharper efficiency curve was achieved. This resulted in improvements to downstream recoveries while alleviating pumping capacities that were previously constrained by fines and water caught up in recirculating loads.Several other case studies are presented which may seem to be relatively basic, but many basics seem to be getting lost in the day-to-day responsibilities of the modern plant metallurgist. Simple fixes to hydrocyclones can result in significant production increases, but more focus is needed in monitoring these to sustain the benefits.CITATION:Wong, B and Vizcarra, T G, 2018. What category cyclone is devastating your plant?, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 665–673 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018