Search Documents

By Horrocks KRS, Smitham JB, Ellison JF

This paper describes the development and installation of equipment for continuously measuring separating density in the dense medium cyclone circuits of the four million tpa Port Kembla B/C plant coal washeries. Monitoring equipment consisting of magnetic coils and differential pressure cells were installed in U-tubes taking the full flow of magnetite from the drain sections of the product drain and rinse screens. The monitoring equipment measures overflow magnetics concentration and overflow density continuously and has operated since 1989. From these measurements and calibration trials, the separating density of operating cyclone modules can be inferred reliably. Variographic analyses of the data show that medium density control to +/- 0.002 RD units and separation density control to +/- 0.007 RD units are achievable. Either method for measuring separation density can be used with approximately the same accuracy, although the overflow density measurement technique suffers from the need to have regular flushing of the Dp cells which complicates the signal analysis. Data from the plant shows that separation density can be controlled by regulating medium density, but the assumption of a constant offset between medium density and separation density is erroneous.

Jan 1, 1993

By Savidis GM

This report outlines the experience of Australian mining operators in dealing with large falls of roof in advance of longwall supports. Previous and present techniques used for face stabilisation have been described, together with an analysis of [actors which contributed to the roof falls, in each case. Attention has been focused on the stabilisation technique used at Angus Place Colliery, where the face coal was successfully reinforced by injecting chemical foam into Lite fractured areas. Although considered to be one of the worst roof falls in the history of Australian longwalls (60 m in length and up to 10 in in height), it was subsequently possible to resume cutting in Longwall 9 two weeks after the foam injection. A preliminary schedule of work involving the 'strata replacement' method, is also discussed. It has been based substantially on experience gained with cementitious supports, principally by ACIRL and Monier Resources.

Jan 1, 1986

Knowledge of the hydrogeological setting of a mine forms an integral part of a mining operation. Groundwater impacts, initially, on mine feasibility. Then, on commencement of mining, it interacts on the operational components of dewatering, water supply, tailings leachates, mine wall stability, stormwater run-off, water disposal, impact on regional environment and mine closure planning. The recording of hydrogeological information is frequently overlooked during resource and reserve definition as well as during the course of mining when prime opportunity exists for the collection and collation of this data. In recent times, the exclusion of hydrogeological data has been exacerbated by use of high air pressure drill rigs that exclude water inflow. The recording of water data has been further inhibited by the use of computer coded drill logs that do not include the site geologistÆs or drillerÆs comments on drilling problems and observations associated with groundwater intersections. Geologists now infrequently directly supervise drill rigs, but visit the rig only intermittently to evaluate drilling progress. They do not see first hand drill performance characteristics at water make zones. Drill cuttings, as drill chips and cores, are now mostly logged away from the drill site so that wet sample locations, visual water flow evidence and verbal comments from the driller are not recorded. As a result, mine geologists now do not direct adequate attention to the delineation of lithologies and structures that store and transmit water. This paper provides examples of water sighting and recording techniques applicable to a mining operation. Examples are also provided where hydrogeological conditions have been disregarded with serious impact on the progress of mining. The recording of hydrogeological data should be maintained and formatted by the site geologists into a useful database for review as and when required by specialists in hydrogeology, geotechnical and mining engineering and the environment. The information can be coded by the site geologist for inclusion into the mine database. A groundwater dataset, compiled during the progress of field investigations, will save the considerable cost of re-drilling and hole re-entry testing which would otherwise be required to provide base level hydrogeological information required for progress of mining. Apart from working mine use, a hydrogeological dataset is a necessary component for planning mining closure and mine legacy conditions.

Jan 1, 2003

WINDING engines are one of the most important units in the equipment of a mine. Upon the winding machinery depends not only the output of the mine, but it supplies in most cases the only means by which workmen enter and return from the mine, and consequently the utmost care and attention is desirable in its design. The efficiency of a direct acting winding engine, as a machine is very low. In other words, the proportion between the useful work performed and the actual work the engine is capable of performing (under the most favourable conditions) is very small. The reasons for this are:-1. The intermittent nature of the work; the engine is stopped from 20 to 25 %(or even more) of the time which would constitute a useful day's work.2. The large amount of power that is absorbed applying the brakes to bring the load to rest.3. That the net useful load raised is small in comparison with dead load to be lifted, and the parts to be set in motion.4. That, owing to the frequent stops, initial condensation in the cylinders is always greater than in a continuously running engine, whilst radiation from steam pipes, valve chests, &c., goes on whether the engine is running or...

Jan 1, 1911

The paper presents an overview of the mining industry of Papua New Guinea. Although the Bougainville problem is still unresolved, new mines like Ok Tedi, Misima and Porgera, which have come on stream during recent past, have raised hopes of sustained growth period in the industry. Kutubu Oilfield is also being developed in the Southern Highlands and the oil production has commenced from July 1992. Government revenue from these mega projects will increase five-fold during 1993 and 1994. A new mine which is being planned is the fabulous Lihir Deposit, on an island renowned to be full of gold. Gold occurs within a volcano which still contains high temperature ground water because the system which created the deposit is still geothermally active.In Papua New Guinea, problems of environmental management are far easier to tackle than those of a socio-political and economic nature involving compensation payments to the landowners and the distribution of royalties and taxes between the national and provincial governments. At the socio-political level, the country has not been able to resolve the problems of land rights versus mining rights. Whenever mining starts in a big way, it raises people's expectations to a very high level, which then becomes the focal point of dispute between landowners, provincial governments, national government and mining companies. A new system called 'Forum' has been tried to bring all parties together and son out the issues. The system appears to be working well in new mines like Ok Icdi, Porgera, Misima and Kutubu Oilfields.

Jan 1, 1993

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

By Kuipers A. J

Aberfoyle has been applying computer methods to mine geology in small to medium-sized underground mines since the early 1980's. Recently, the installation of DATAMINE software at the Hellyer Mine in Tasmania has allowed development of computerised applications which assist both mine geologists and mine planning engineers on a daily basis.Comprehensive data is entered into a database prior to survey coordinating to produce a processed database which can be accessed for construction of a variety of plots. The folded and faulted nature of the orebody contacts at Hellyer has necessitated the use of the structure contour method to provide a complete 3-D spatial interpretation. Computer-generated contact intersection points are hand-contoured before digitising and wireframing as a digital terrain model. This wireframe model can be sectioned in any plane for mine planning.

Jan 1, 1990

By T Laurencont, C Unger

The Mount Morgan minesite, located approximately 40 km SW of Rockhampton in Central Queensland, comprises 270 ha of unrehabilitated land which is the currently the major source of acid mine drainage run-off and seepage to the adjacent Dee River. Additionally, the minesite hosts an Open Cut Pit which contains 9000 ML of acidic and metal-rich water. In the absence of active management of water in the pit, there is a 50 per cent probability of an uncontrolled spill occurring in future years. The development of a contingency plan for management of overflow from the pit in the short term, has incorporated findings from numerous studies relevant to the Open Cut Pit including, but not limited to, water balance, contaminant source identification, toxicity testing, water quality profiling and limnological modelling, and estimates of probability of overflow. Extensive stakeholder consultation and peer review were also undertaken during the formulation of the contingency plan. The medium-term goal of lowering the water level in the pit to reduce the current high probability (50 per cent) of uncontrolled overflow to acceptable levels of risk is proposed to be achieved by a campaign of chemical water treatment. The treated water will be discharged to the Dee River, and sludge returned to the pit. The methodologies used for the selection and development of the water treatment process, that is proposed to involve treatment with lime, are described. Water treatment is the short- to medium-term component of a long range rehabilitation plan for achieving a negative pit water balance, and sustainable management of acidic water across the whole site. Achieving this ultimate goal will involve: reducing the inputs of water to the Open Cut Pit such that the annual water balance is zero or net negative, thus removing the need for water treatment in perpetuity; maximising, by surface rehabilitation works, the quality of run-off reporting to the Dee River; and minimising the volume of acidic seepage reporting to the seepage interception system. Possible strategies for achieving this long range goal consistent with overall site rehabilitation objectives are currently being developed and costed.

Jan 1, 2003

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

By C McIntosh, M van Dam, N Whetter, R Lane, M McCulloch

Mine geology is understood through synthesising large amounts of structural, lithological, geochemical and geophysical data derived from the original topographic surface, drilling and surfaces exposed and removed during open cut and underground excavations. Computer- generated 3D geological models of any mine environment need to incorporate large amounts of information but also should be regularly updated with typically frequent influxes of new data. Geologists with the local knowledge should also be involved in the model construction, enhancement and interpretation, placing ease-of-use functionality high on modelling software requirements. Implicit-style modelling is a fast-growing area of 3D geological software development where interpolated surfaces such as lithology boundaries and bedding orientations are defined mathematically as functions rather than explicitly through coordinate meshes. The functions are constrained only by the data and not by an artificially imposed grid; therefore, implicit 3D modelling can process a lot of information quickly and routinely operate on original data (such as observed contacts and structural data) rather than on evolved iterations and interpretations. 3D mine geology models can be readily updated with new data, which can be automatically reprocessed to test ideas in near-real time. Implicit, function-based 3D modelling software has been applied to the Globe-Progress mine in West Coast, New Zealand. This structurally- hosted gold mine has some geometrical conundrums that are in part being resolved as excavation of the open pit proceeds. The relationship of the Globe-Progress ore shoots to hanging wall and footwall structure is still not fully understood, however, and 3D geological modelling is assisting with visualisation and testing of structural hypotheses. The modelling is also capable of predicting areas of bedding defect slope failure in yet-to-be excavated parts of the mine.

Jan 1, 2009

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

The winning and upgrading of mineral raw materials necessarily includes size reduction, which serves the liberation and production of marketable products from highly valuable and bulk materials. For crushing, the following factors can be duly accounted for depending on material type and the selection of the suitable machine: ò producing a particular size distribution, ò producing a particular grain shape, ò selective comminution, ò gentle comminution, and ò producing a size range required by a specific process and/or for a specific product.

Jan 1, 1993

Extraction under very mild conditions - a few minutes at room temperature with poor solvents - yields results characteristic of surface properties for a variety of coals. Such superficial extractions preferentially remove long-chain aliphatic compounds. As coal becomes more oxidized, less of these yellow- colored compounds is extracted, forming the basis for a simple colorimetric test for coal surface quality. The fact that these aliphatic compounds are responsible for surface hydrophobicity is supported by good correlation between extraction results and floatability, which decreases with decreasing extractability. This extraction test is very sensitive to oxi dationb even the effect of heating for an hour at 100 C can be detected. A second extraction test using mild alkali conditions has shown good correlation with plant dewatering Operations.

Jan 1, 1986

This paper introduces a new, safer bulk emulsion loading system for underground mining operations. The features and benefits of the equipment, along with the use of Dyno Nobel Inc patented gassed emulsion technology, is summarised in the application of a stope blast with very difficult and complex ground conditions. The paper describes methods used to optimise the amount of energy required to break the ore while protecting the integrity of the surrounding backfilled pillar.

Jan 1, 2004

By Hebblewhite B, Humphreys D

An experimental mining project has been carried out in the Collie Basin to demonstrate the safe operation of total extraction mining techniques in the underground mines of the basin. To achieve this, it was necessary to design and install a means of controlling or removing groundwater so that goafing of the overlying strata could be safely achieved as part of the mining operation. The site chosen for the experiment was a triangular panel adjacent to Western No 6 (WD6) underground mine, which includes the 3 to 4 m thick Wyvern Seam beneath 130 to 180 m of overburden. The test area abuts a major fault on the downdip side. The overburden and underburden sequences include several horizons of permeable sandstones which form major aquifers. Water problems have long been recognized in all underground mines in the Collie Basin, and have previously prevented the successful application of total extraction mining. Following extensive hydrological investigations, dewatering and depressurization systems were designed to dewater the immediate roof aquifers and to depressurize aquifers higher in the sequence and in the floor. This would enable stable roof conditions to develop and controlled goafing to be achieved. The roof dewatering/depressurization procedure involved a combination of in-mine vertical roof drainage holes and conventional dewatering bores constructed from the ground surface above the mining trial area. The dewatering system was installed and operated for 29 months before the commencement of mining. Mining was eventually successfully completed in two trial panels using a retreat Wongawilli extraction system using bridge conveyors and continuous miners. Water inflow into the mine workings was channelled to a constructed sump area at the lowermost corner of the panel and pumped to the surface via vertical sump bores. The dewatering and depressurization measures adopted were successful in permitting the first controlled and systematic total extraction recovery of coal from the Collie Basin. This trial mining exercise demonstrated the potential for increasing substantially the recovery of coal from the Collie Basin, where previously recovery rates of around 30 percent from underground mining were commonplace, using only bord and pillar methods.

Jan 1, 1988

By C Morley, B Costello

In 2002 the Argyle Diamond Mine upgraded the process plantÆs recrush circuit to include a High Pressure Grinding Roll (HPGR), or High Pressure Rolls Crushers (HPRC) as they are termed in the diamond industry. HPGR have generated considerable interest over the last decade, though there are still technical/processing unknowns to its effectiveness as a primary diamond ore crusher.The upgrade of the Recrush circuit at Argyle Diamonds has gone a long way to answering some of the key questions, and thus it has reduced the unknowns to a level more acceptable to the industry.This paper focuses on the results from the HPRC at Argyle, in particular the performance of the studded wear surfaces, comparison of energy efficiency against traditional quaternary cone crushers and the resultant increased liberation. Issues that have arisen, including edge wear of the studded surfaces, will be discussed and the steps taken to reduce this issue are presented.

Jan 1, 2004

By Aspinall T. O, Bell L. C

Increased awareness and stricter enforcement of regulatory requirements for adequate rehabilitation of surface mining sites has made environmental planning an essential part of strip mine planning. Rehabilitation is site specific and should be based on data which relate to that site. Cost-effective spoil pile design to minimise erosion is an important part of rehabilitation. Spoil pile design is an integral part of strip mine design. QCT Resources Limited has provided a postgraduate scholarship toward research in this area. The controlling factors of spoil pile design are post-mining land use, drainage requirements and degree and rate of erosion. The extent to which mine design is controlled by these factors is determined by regulatory requirements. To plan acceptable rehabilitation programs, erosion processes must be accurately modelled, and a range of erosion prediction models are available. Useful prediction models can be placed in two categories with the first category containing soil loss prediction models which can be used to predict the amount of soil lost from an area over a short or long term basis. Models in this category include the Universal Soil Loss Equation (USLE), Water Erosion Prediction Project (WEPP), Griffith University Erosion and Sedimentation System (GUESS) and Chemical, Runoff and Erosion from Agricultural Management Systems (CREAMS). The second category contains topographic evolution models which give an indication of the long term morphological development of a formed surface subjected to erosion processes. Models in this category include "Topog", Willgoose's Physically Based Catchment Evolution Model and Areal Nonpoint Source Watershed Environment Response Simulation (ANSWERS). The USLE has been used in the agricultural field for soil loss prediction. To apply the equation to mine sites in Central Queensland, it is necessary to understand the factors affecting erosion at the sites. This understanding should allow the variables of the equation to be quantified. The rainfall factor applied in the USLE is independent of engineering design or soil management techniques. The factor of spoil erodibility is dependent on the material's physical and chemical properties and can vary from site to site. In the equation, the topographic factor, cover and management factor and conservation practices factor can be varied by design to reduce erosion on rehabilitated areas.

Jan 1, 1991

By Gillies A. D S, Just G. D

Coal washability data can be used for assessing coal quality. However, the techniques of using these data to solve quality problems differ from one mine to another and certain problems may never really be investigated due to limitations of the available techniques. One promising way to overcome these limitations is by correct application of geostatistics.A geostatistical study on coal washability data was undertaken based on a data set of closely spaced in-pit bore cores. These bore cores were analysed consistently over a relatively simple geological area. The average distance between the drill holes was about lOOm. There were 78 drill holes available for the area after deleting the erroneous bore cores. During the study, nine extra closely spaced drill holes were drilled within a single mining block.A procedure to construct two coal quality models, a kriging or cokriging model and a simulation model, was proposed. The modelling results for the data above are discussed and results of a mine scheduling exercise based on the models developed are included.

Jan 1, 1992

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

By Cudmore JF, Rowlands D

Incidents associated with spontaneous combustion of coal have resulted in the loss of many lives and considerable capital and equip- ment. Nevertheless, the factors controlling the propensity of coal to spontaneous combustion are not clearly understood and there is a need for research to study the effects of rank, petrog- raphy, moisture contents, etc. This has been attempted in a study of the propensities of selected Queensland coals to spontaneous combustion. An adiabatic calori- meter was constructed to study the self-heating of a large number of coals. Chemical and petro- graphic analyses of the coals were determined and an attempt was made to relate these propert- ies to the self-heating characteristics of the coal. The results show a strong relationship between rank and self-heating characteristics and that petrographic composition of coal may also be of importance. Some observations on the application of the laboratory results to the practical situation are made as are recommendations for future research.

Jan 1, 1981