Search Documents

By Webster SS

This paper uses computer modelling tech- niques to compare and contrast anomaly patterns obtained with fluxgate (vertical field) and proton precession (total field) magnetometers at typical latitudes in northern and southern Australia. The use of these modelling tech- niques is suggested as an aid to magnetic interpretation and field examples are included from Tasmania and the Northern Territory.

Jan 1, 1975

By Watt JS

The ash content of coal can be determined using radioisotope X-ray techniques. A number of overseas applications of X-ray techniques are described; however these suffer from the disadvantage of either not compensating for iron variations or, if compensation is used, using X-rays of low penetration with consequent sampling difficulties. Current Australian Atomic Energy Commiss- ion (AAEC) research on X-ray techniques is aimed at overcoming the limitations of these methods. The AAEC method involves making measurements proportional to mass absorption coefficients of X-rays in coal at two energies. Calculations and experiments with X-rays up to 35 keV have shown that ash content can be determined to about 1 wt.%. This work is being extended to higher X-ray energies to enable the technique to be used directly on a conveyor belt or in a hopper. Neutron techniques can be used to measure the concentration of specific elements such as carbon, hydrogen and silicon in coal. Their con- centration is correlated to the coal parameters of interest. Methods of moisture determination based on hydrogen measurement and ash determina- tion based on silicon and aluminium measurement are described. Energy content can be determined accurate- ly by analysing the carbon content of coal

Jan 1, 1978

By Kyle J. H, Browner R. E

The selective adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4* and Duolite A-7*, the neutral polymeric adsorbent, Amberlite XAD7*, and the strong base resins, PAZ-8 and IRA-400+ have been studied in both low and high salinity waters, and performance compared with activated carbon. The selectivity of the neutral polymeric adsorbent and activated carbon for gold decreased in highly saline water, while the selectivity of weak and strong base resins for gold increased in highly saline water. This supports the contention that the adsorption mechanism for neutral polymeric adsorbents and activated carbon is the same. Copyright

Jan 1, 1992

By Fukuichi K, Matsukawa H, Nakagawa M

The Myojin Tunnel, located on the Shikoku Expressway being constructed by the Japan Highway Public Corporation, is 3,770 m long with a cross sectional area of 80 m2. Kajima Corporation, the contractor for the northern construction section of this tunnel, adopted here its newly developed "mini-bench" method of excavation. The objectives of this method were 1. to be able to perform all tunnelling operations using the whole cross sectional area of the tunnel under any ground conditions, and 2. to be able to vary the length of the mini-bench within the range of 0 to 7 m according to ground conditions. In order to achieve these objectives, original, sophisticated equipment was developed and employed in the work. One of the newly developed machines is a special jumbo, a hydraulic crawler jumbo with five rotary type booms. This machine is capable of accommodating variation in the length of the mini-bench accompanying changes in ground conditions and is equipped with a special mechanism by which the positions of the booms can be controlled by means of hydraulic cylinders. Also developed was a shotcrete robot for use with the mini-bench method which has the control board near the shotcrete nozzle for close control of application.

Jan 1, 1987

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

General Gold was discovered in quartz veins at Wiluna in 1896, and the first lode was discovered in 1904. Since 1896, some 2.5 million ounces of gold have been produced from the Wiluna area. The mining operations at Wiluna are 100 per cent owned by Wiluna Gold Pty Ltd, a wholly owned subsidiary of Wiluna Mines Ltd. Oxide and sulphide gold ore is extracted by conventional open pit mining techniques, and ran-of-mine ore is processed through two separate circuits. The oxide circuit has a capacity to treat 600 0(X) tonnes per annum and the sulphide circuit has a capacity to treat 400 (XX) tonnes per annum. Additional gold is won by dump leaching sub-grade oxidised ore and by retreating of primary ore flotation tailings from previous operations. Testwork carried out in 1990 indicated the viability of leaching dumps of run-of-mine oxide ore, and in June 1991 Signet Engineering of Perth, WA, was awarded an EPCM contract to construct a nominal 2.5 million tonne dump leach facility, for a total construction estimate of 51.75 million.

Jan 1, 1994

By Smith PE

The main components of face design are the power loader, face conveyor and powered support system and the interaction of these components determines the effectiveness of strata control. A major influence upon the interrelationship of this equipment is the geological environment, of which seam thickness appears to play an important role. Recent thick seam experience indicates a significantly different characteristic behaviour pattern from that observed in thin seams The structural integrity of the face wall is particularly influenced by seam discontinuities such as natural joint planes and mining-induced fractures in the yield zone ahead of the faceline. In addition, the presence of stone bands or dirt partings in the seam offers interfaces for uncontrolled release of blocky material. Some case study experience at British collieries provides a comparison with performance data at a specific location, that highlights the importance of coal face layout and design.

Jan 1, 1986

The dielectric properties of practically all oxide and sulphide ore minerals are such that they heat rapidly when irradiated with microwaves particularly at the standard frequency of 2450 MHz. The presence of carbon or low rank coal mixed with the minerals still further enhances the heating rate. Amongst the patented technologies being investigated are: (i) the direct reduction of oxides with or without carbon included in the pellets or briquettes; (ii) microwave precursor heating of composites ahead of smelt reduction; (iii) microwave smelting of ore or concentrate mixtures with carbon, sometimes assisted with oxygen. Microwaves appear to stimulate endothermic reduction reactions as readily as they do exothermic oxidation reactions. Being a method of achieving "bulk" heating, composites or columns of ore-char blends rapidly heat throughout rather than from the outside inwards as in conventional heating. The microwaves of themselves do not generate any gas - the only gases to be cleaned are the products of reaction in the composites or blends, plus the products of oxygen smelting. In the case of sulphide composites, depending on the quantity and type of low rank coal or char present, sulphur may be eliminated, and collected, in the elemental form. Furthermore, reactions seem to take place at lower temperatures than in conventional smelting but no doubt at the "points" where actual reactions are taking place the atomic or molecular vibrations are such as to satisfy the laws of thermodynamics. Examples are given of the production of unusual products of smelting sulphide concentrates and also the alloys produced from refractory minerals such as chromite and ilmenite. The techniques have been used to produce products with as wide a range of melting points as relatively pure tin and tungsten-molybdenum alloys. Special equipment is being designed and evaluated for these new fields of pyrometallurgy.

Jan 1, 1989

By Rosengren KJ

Geotechnical conditions often have a critical influence on the design of new open pit and underground mines, but they are often considered of secondary importance in relation to other factors, such as detailed geology, orebody geometry and grade distribution. As a result, geotechnical studies may not be carried out during early project investigations or, at best, may be given only superficial attention, often to the overall detriment of the project. Technically and economically, it is logical that geotechnical studies should be integrated with geological investigations as soon as it becomes evident that the particular deposit may prove to be economic. The paper discusses the use of geotechnical information in the selection of mining methods and mine design for underground mines and for wall design and assessment of excavation characteristics in open pit mines. It then considers methods of obtaining the relevant data, with particular reference to exploration boreholes. Selected case studies on the application of geotechnical data to mine design are Included.

Jan 1, 1986

Total extraction is a misnomer and invariably some coal losses occur in the mining of pillars. "Fulls" pillar extraction is by the pocket and fender method, the splitting method or the open end method, with extraction in the pillar, and in rows of pillars in planned sequence, using combinations of coal and timber and roof-bolts for support. Where circumstances dictate, partial extraction is used, leaving behind portions of pillars in large blocks for support. The use of such extraction plans and supports as minimum guidelines has contributed greatly to safety in United States Coal Mines.

Jan 1, 1974

A survey of leaching systems for the dissolution of gold has been undertaken and their advantages and disadvantages evaluated both from their effectiveness at leaching and their compatibility with carbon- in-pulp (CIP) and resin-in-pulp recovery. In the near future it is almost certain that cyanidation in some form will remain the leaching system of.choice although economic and environmental pressures could see the introduction of other leaching systems particularly for treating refractory gold ores. The most likely alternative leaching systems appear to be acid chlorine, acid thiourea and ammoniacal thiosulphate. INTRODUCTION High grade reserves of readily recoverable gold ores are gradually being depleted which, inevitably, must create a greater awareness amongst gold producers, of the efficiency and, in some cases, the suitability of present day metallurgical processes for treating low grade, complex and refractory deposits. One of the key steps in the extraction of gold is the dissolution of the metal using chemical reagents which, ideally, should be cheap or recyclable, selective, non-toxic and compatible with down-stream recovery processes. In practice, meeting all these critera is difficult - if not impossible - particularly in view of the stringent environmental impact requirements which must be met Nowadays.

Jan 1, 1982

There are serious problems in forecast- ing accurately and achieving this goal depends on good quality information, correct assumpt- ions and sound analysis. planner. The forecaster must focus attention on a number of key areas of interest. These areas include major economic trends and changing GNP structure, consumption time series, end-use consumption patterns and substitution potential, accurately updating data bases (up to 5 years ahead), random factor estimation and examination of both long term and secondary mine potential. While metal price forecasting has suffered due to recent uncertainties, with increased importance on planning tools and cost analyses, it is still a necessary function. Forecasting is subject to the real world and the metal industry is made up of imperfect markets in a dynamic state. The real world provides the challenge to improve the accuracy of forecasting.

Jan 1, 1983

By Wardle L, Wright G

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modem houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various' house designs.

Jan 1, 1992

By Yan D. S

The removal of antimony from a refractory gold-bearing stibnite ore by roasting and selective chlorinating roasting was investigated. The influence of roasting temperature, roasting time, roasting atmosphere and type and amount of chlorinating agents on antimony removal were studied. The laboratory studies carried out included roasting tests of 4 g samples in a laboratory rotary kiln, followed by 400 g samples roasted in a fluidised bed. The test results revealed that antimony was efficiently removed by roasting at temperatures over 800¦C in a nitrogen atmosphere. The most efficient volatilisation of antimony was achieved with the addition of ferric chloride at temperatures between 350-600¦C.

Jan 1, 1995

By Barnes R. G, Agostini A, Lewis P. C

The Mineral Resources Audit is a five-year Program established to produce a comprehensive and objective assessment of the mineral resources of New South Wales, including prospective resources. The goals of the Program are to improve planning and land use decision-making; attract exploration and minerals related investment; help the Department to identify and fill gaps in knowledge; and develop methods to identify and quantify resource potential and prospectivity. To achieve the goals of the Audit it is necessary to assemble and enhance a large amount of information and it is necessary to spatially analyse this information using computer-based Geographic Information Systems (GIS) which allow the collection, storage, transformation and display of large quantities of spatial data. An extensive range of both map-based and textual data can be employed in spatial analysis and resources and geoscience modelling. In order to use this information, data sets have to be corrected and standardised. Many data sets need to be classified. An objective of the Audit Program is the spatial analysis of the State, region-by-region, and the release of cleaned-up multiple digital data sets as packages which include upgraded mineral deposit information, 'seamless' geological map layers showing lithology, structures and stratigraphy, and processed and classified geophysical map layers. These regional packages are important reference sets for the mineral resources industry and will assist delineation of regional exploration targets.

Jan 1, 1995

By den Drijver J

Worldwide, hard coal mining is being carried out at ever increasing depth, and has, therefore, to cope with correspondingly increasing methane emissions. About seven per cent of global methane emissions are caused by coal mining. Beside carbon dioxide, chloro-fluorocarbons (CFCs) and nitrogen oxides, methane is one of the most significant `greenhouse' gases. It is mainly through the release of such trace gases that the greenhouse effect is brought about. Reducing methane emissions is therefore an important problem to be solved by the coal mining industry. This paper begins by highlighting some of the fundamental principles of methane in hard coal mining. The methane problem in German hard coal mining and the industry's efforts to reduce methane emissions are presented. The future development in German hard coal mining is illustrated by an example which shows how large methane volumes can be managed, while still maintaining high outputs at increasing depth.

Jan 1, 1995

Although developed primarily for sintering tantalum, the unit to be described can be used to heat-treat metals in the form ofa bar, wire or strip, by passing a current through them. The upper temperature limit with this type of heating is the melting point of the metal being heated.The unit was designed for vacuum work, but. various gases can be used if required.Briefly, the vacuum sintering furnace consists of a bell which is counter-balanced and may be lowered onto the brass base plate which holds the electrodes. A rubber ring seal is used for vacuum work. The lower flexible grips are bolted to the brass base plate which is at earth 'potential, while the other electrode passes through the plate by way of an electrically insulated vacuum seal. This upper electrode, the height of which can be altered as desired, the lower grips, and the bell are water cooled. The vacuum line to the pumps and a line to the vacuum gauges also lead from the base plate. The more important sections of the unit are described below.THE BELLThe unit was designed so that the bell could be lifted clear of the base plate and the electrodes, thus facilitating adjustment of the latter and the mounting of the specimen to be heated. A double walled steel bell, 20 in. high, with t in. cavity was used. The bell was fabricated from 10 gauge mild steel sheet using a double overlapping run of arc welding for all seams. A water inlet and outlet...

Jan 1, 1946

The calibrated thermal IR data of part of Cambay Basin is used to determine surface temperatures and to detect the heat flow. Applying the conductive heat flow continuation technique, the three dimensional configuration of the hydrocarbon bearing reservoir was defined. The zone delineated by the present study coincides with the oil-bearing structures inferred by seismic survey. The results indicate the possibility of the technique as an effective tool in hydrocarbon exploration.

Jan 1, 1986

The orebodies at Kambalda are complexly faulted, folded and intruded. It is realized that the ore reserve calculations will be wrong and steps are taken to minimise the errors. The calculations are a combination of computer data handling and manual input. Initially Geological Ore Reserves are calculated and then production data and experience are used to produce a Planned Mining Reserve. At all stages maximum professional judgement is incorporated. The basis of the calculation is the polygonal method of area estimation, and production reconciliations together with the style of data available indicate that it is a most suitable technique. It is also a tech- nique that is easily communicated to all levels from operators to management.

Jan 1, 1979

By McGaffin I, Loah J

PT Newmont Minahasa Raya (PT NMR) is an Indonesian joint venture subsidiary of the Newmont Gold Company of Denver, Colorado, USA. PT Newmont Minahasa Raya operates a 700 000 tonne per annum gold plant in the Minahasa region of North Sulawesi, Indonesia. At full capacity the plant is expected to produce an average of 150 000 to 180 000 ounces of gold per year until the year 2007 based on current existing reserves.Exploration began in 1986 and high grade mineralisation was discovered in 1988. Subsequent drilling defined a resource of approximately 2000 000' ounces. Reserves as of 1 January 1997 were 7 035 000 tonnes grading 8.46 grams per tonne, for 1 913 000 contained ounces. Metallurgical testwork commenced in 1991. Construction of the plant started in late-1994 and the first gold was poured in March 1996.

Jan 1, 1997