Search Documents

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

The Mt Newman Beneficiation Plant uses a combination of heavy media deans, heavy medium cyclones and Reichert cones to produce saleable iron ore concentrates from low grade iron ores. The aim of this paper is to discuss score of the changes that have been made to improve the operation of the heavy medium circuits.

Jan 1, 1987

Up to 80 per cent of the copper in a bornite ore can be quickly leached with percolating acidified ferric sulphate solutions. The upper limit for rapid copper extraction is set by the conversion of bornite to slowly dissolving chalcopyrite. The dissolution occurs in two stages: a rapid linear initial stage, followed by a slow, non-linear stage. The initial step is largely controlled by the rate of oxidant supply (Fe2(S04)3); temperature is not an important variable during the initial reaction. The second leaching stage is controlled by chemical and physical factors and is temperature dependent. The initial copper leaching rates are insensitive to both the concentration of the ferrous sulphate reaction product, and the sulphuric acid concentration.

Jan 1, 1973

The design of a sand pump is similar in principle to that of a water pump but differs in several areas. Results of experiments on sand pump performance have been summarized and values of design parameters quoted for optimum results. Typical performance data are also Included.

Jan 1, 1973

In order to fully understand why Amax Coal puts such extreme emphasis on the drilling and blasting programs at each of our mines, we must review the past. This paper will discuss the drilling and blasting techniques we used in the 1970s and their evolution to current practices. As time progressed, major changes influenced the surface mining of coal through new more restrictive governmental controls and local communities organising into groups with two goals in mind, one to shut down the mines and the second to try and get rich by making false and unjust damage suits against the mines. In virtually all of our midwest surface operations we have at one time or presently are facing litigation that has reached into the millions of dollars. Amax Coal has worked in co-operation with the United States Bureau of Mines in the areas of blast vibration, shot design, highwall safety, blast casting studies and many more. Today we are continuing to work with Dr David Siskind and his expert staff seeking answers to old and new problems addressing the blasting of overburden and parting seams.

Jan 1, 1995

Changes in mining technology have led to an increase in the number of underground sulfide dust explosions reported in Australian and overseas mines. Samples collected at the Elura mine consisting primarily of pyrite, pyrrhotite, arsenopyrite, sphalerite and galena, were tested in 8 litre explosion chamber. The dusts were found to be capable of producing dangerous dust explosions with maximum explosion pressures of 440 kPa and rates of pressure rise of 5200 kPa/s. The hazards of a sulfide dust explosion are associated with the pressure wave and flame front of the explosion and the toxic gases remaining after the explosion.

Jan 1, 1984

By Adamiak Z. P, Nicol S. K

An exploratory study has been carried out on the applicability of pre-nucleated feed in pelletising operations. Measurements of the pellet quality parameters showed that iron ore pellets prepared in the above manner, generally meet the specifications required in international pellet traffic. Several potential economic advantages, such as reduced grinding power requirements, increased line productivity and shorter start-up periods, became apparent during the study.

Jan 1, 1974

Pbo activities have been measured in conventional blast furnace and direct smelting type slags at 1200¦C. Much higher activity coefficients than previously measured have been obtained and attributed to interactions between iron and lead oxides. The behaviour of PbO in the two types of slag reflects their relative silica contents. Simple equations derived from mathematical modelling work are presented for the prediction of Pbo activities in complex industrial slags.

Jan 1, 1984

By Follington I. L

Various methods for stress measurement in the coal industry are briefly reviewed. Methods for presenting and interpretation of measured stress and displacement data are discussed with a view to assessing the mechanisms of failure. Arguments are presented for reviewing the current practices in this regard with reference to coal pillar and strata stability analyses.

Jan 1, 1991

By Kewu W

Kaolin used as an industrial mineral, especially that in the paper-manufacturing industry, must be of fine size, with high brightness, a low impurity content, and good crystal shape. However, in most kaolin deposits there are various impurities which have a very bad effect on the quality of the kaolin. Therefore, it is necessary to remove these impurities from kaolin ore. Owing to their similar surface properties, the separation of kaolin and iron oxide minerals, especially microkaolin and iron oxide minerals, has been regarded as difficult. The iron oxide minerals often intergrow with kaolin in fine and complicated forms, such as thin films, which make separation difficult. In order to overcome this difficulty, many workers have suggested various treatment methods and obtained great success. Based on research work by Fuerstenau (1980), Huang, Li and Hu (1984), Hui and Wei (1991), Shergold (1978), and Zambrana et al (1974), we have investigated a two-liquid flotation technique for iron removal from kaolin and obtained some success.

Jan 1, 1993

Automatic sampling and weighing of copper sulphide concentrate produced on Bougainville Island (PNG) is described. Contained metal weights gave satisfactory agreement with buyer's results after the introduction of polyethylene lined sealed aluminium foil bags for transport and storage of assay samples. Paper bags used previously for this purpose permitted oxidation of the sulphide concentrate and thus caused lower assay values.

Jan 1, 1976

Creating Value and Improving Environmental Performance by the Recovery of Valuable Products from Tailings from the Athabasca Oil Sands in Alberta, Canada

Sep 13, 2010

By T Mahlangu

The leaching of gold in alkaline aqueous cyanide solutions may be reduced significantly by the passivation of the gold by a surface layer of polymeric aurocyanide. This passivation of the gold is typically countered by the presence of Pb(+2) species in solution, which may be present as an impurity in the solution, or specifically added for this purpose. The speciation and availability of Pb(+2) in typical cyanide leach solutions is illustrated as a function of pH, and the presence of S(-2), S(+6), Cu(+1) and Ag(+1) species. The probable role of the Pb(+2) species in efficient gold leaching is discussed.

Jan 1, 2007

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

For many crushed aggregate producers will the finest fraction minus 4 mm represent a problem. The fine material will fetch a much lower price than the coarser products, and may even be difficult to sell in some markets. The blasting operation will strongly influence the generation of fines after both blasting and crushing. Drill hole deviation together with the drill hole diameter, powder factor and velocity of detonation are the most important blasting parameters with regard to the generation of fines. Drill hole deviation is often ignored, and many operators will just reduce the drilling pattern in order to avoid hard bottom and an excessive number of boulders. The paper presents a technical and economic analysis of how drill hole deviation will lead to an increased generation of fines in crushed aggregate production. The analysis shows that the loss of sales revenues will be much higher than the extra costs for drilling and blasting caused by compensating for drill hole deviation by putting in more holes.

Jan 1, 1999

To the layman or the casual in- vestor, the critical problems in the mining industry appear to rest on the questions of finding and developing an orebody. The high cost of finding a major orebody suggests that the search is the only matter of real concern. However, the resulting operations which hopefully will provide a profit- able return, depend very heavily on the quality of the servicing that the particular industry receives. Once the mining venture has been established with the necessary plant, equipment and infrastructure, the routine servicing becomes an important function of the operations.

Jan 1, 1975

Developments in furnace construction and design have been very rapid in recent years. Larger furnaces operating at high top pressures with much improved burdens are giving extremely high production rates. Modern scientific techniques and the use of computer control are contributing to these Rates.

Jan 1, 1972

By Weatherhead J, Grounds J

The Nabarlek Uranium Project located in Arnhem Land in the Northern Territory of Australia was a small high-grade deposit which was the first uranium mine brought into operation following the extensive Commissioner Fox Inquiries into uranium mining during the late 1970s. The operation is almost complete and decommissioning plans have been prepared. This paper reviews all phases of the water management and tailings disposal for the project and compares results with design predictions.

Jan 1, 1988

By J C. Small

Time-dependent deformation occurs when geo-materials are under an applied load; this may lead to additional deflection of a tunnel structure and the stress redistribution in the surrounding rock, shotcrete lining and rock bolt support system over time. A better understanding of this creep behaviour can improve the reliability of design, construction and maintenance of tunnels. Hence, the present investigation was carried out on the time-dependent properties of rock, shotcrete and the combined tunnel support system. Tunnels constructed in different ground conditions were modelled. The closure changes of the tunnel with time and the redistribution of stress in the surrounding rock, shotcrete lining and rock bolts due to the creep deformation were analysed. Results of the present analysis were compared with the results from the commercial program ABAQUS.

Jan 1, 2008

By Baafi E. Y

A heuristic approach for the optimisation of the stope geometry is presented. The heuristic method uses economic model of a given deposit to search for the best combination of mining blocks that results in the maximum profit while imposing geo

Jan 1, 1998