Search Documents

By P J. Vardon, L A. van Paassen, Y Yao, A F. van Tol

Thin-lift atmospheric fine drying (AFD) is a technique used to dewater mine and oil sand tailings, which utilises both self-weight consolidation and atmospheric evaporation. The disposed layers undergo a cyclic drying and rewetting process due to precipitation and deposition of additional lifts on top of the dried layer. The current research aims to optimise the deposition process via use of a numerical model and realistic atmospheric conditions, including both periods of drying and wetting. The model is based upon water balance and includes large strain considerations. A number of material behaviours are characterised using empirical fitting curves based upon laboratory measurement of material characteristics, including both the shrinkage and water retention curves for drying and rewetting. The model is able to model multiple lifts, simulating field scale and realistic climatic conditions within timescales suitable for engineering practice (eg seconds or minutes). The model has been previously validated against controlled laboratory experiments and utilised to simulate field tests. A series of simulations are presented to illustrate the ability of the model to be used as a practical tool for the optimisation of a tailings deposition strategy.CITATION:Vardon, P J, Yao, Y, van Paassen, L A and van Tol, A F, 2015. The use of a large-strain drying and consolidation model to optimise multilift tailing deposits, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 263–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Baumgartl, C Gonzales, A Soliman, M Edraki

A soil cover isolates potentially acid-forming (PAF) mine wastes from atmospheric interaction and thereby mitigates acid mine drainage. As a cover that comprises either a single layer or a composite barrier, it essentially manages percolating rain water from flowing into these PAF materials and minimises air flow as oxygen has low diffusivity in saturated soils. However, the availability of suitable soils as cover materials is limited, especially in arid and semi-arid regions where weathering rates are low.This paper investigates the potential use of mine wastes as cover materials in a water-shedding soil cover in north-west Queensland. Four cover trial plots were built using mine wastes as cover materials. Each 2.3 m cover trial plot consisted of a 1.5 m soil cover made up of waste rocks and fines, a 0.5 m drainage layer that consisted of 0.1 m waste rock aggregates and a base layer made up of blended mine tailings. The hydrologic properties of cover materials were determined by in situ measurements and laboratory experiments, which, in turn, were used as input in a numerical model that described the cover’s transient soil moisture profile. The successful performance of the cover is reliant on the long-term stable geochemical behaviour of the substrate used as cover material. Therefore, investigations were carried out to determine the geochemical properties of the cover materials constructed from benign waste rock using static and kinetic tests, with the objective to increase the level of certainty of the material’s benign characteristics. Consequently, the long-term performance of this water-shedding cover design is described in terms of the physico-chemical characteristics of its outflows.CITATION:Gonzales, C, Baumgartl, T, Edraki, M and Soliman, A, ?2014. Mine wastes as cover materials in a water-shedding soil cover in north-west Queensland, in Proceedings Life-of-Mine 2014 , pp 261–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M E. Watson

Minimising dilution and ore loss is an important part of ensuring profitability of a gold mining operation. White Foil open pit gold deposit is a low-grade deposit and therefore managing ore quality is a high priority. Ground movement through blasting can displace ore and waste boundaries up to 10 m from their in situ location and therefore requires stringent ore movement monitoring and adjustment. There are currently only two options for monitoring blast movement – utilising visual targets (commonly lengths of polypipe) but this has widely been replaced by electronic blast movement monitors (or BMM). Regardless of the technology used, the basic principle is to compare the pre- and post-blast locations of the targets to determine the movement of the rock mass during blasting, which is then used to determine the final location of ore and waste boundaries.The Blast Movement Technologies (BMT) BMM system has been used at White Foil since June 2014. The system has been effective and reliable during that time; however, the annual cost of using the BMM system is greater than other monitoring alternatives. As such, the open pit geology team conducted a study comparing the BMM system against the conventional polypipe technique. The objective was to quantify the profit and loss that would occur based on the ore block transformations from both methods. Eight blasts were selected where polypipes were installed in additional holes adjacent to the BMM monitoring holes. The resulting movement vectors from the respective methods were used to create post-blast ore blocks by transforming the in situ ore blocks. While polypipe is a cheaper alternative, the BMM system tracks ore and waste boundaries more effectively resulting in better quality control, enhanced ability to minimise dilution and ore loss thus maximising profit. For these eight blasts, it is calculated that the BMM system resulted in A$664 978 extra profit through a reduction of ore loss. The total cost of a yearly BMM package was recovered in the first two blasts of this study. The primary reason for the difference is that polypipe had a poor recovery rate of 32 per cent compared with 92 per cent for BMM at White Foil. Therefore, the data used to transform the ore blocks was less representative, resulting in inaccurate post-blast ore block boundaries when using polypipe.CITATION:Watson, M E, 2017. Blast movement monitors or polypipe? A study into cost-effective blast movement monitoring at White Foil gold mine, Western Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

In high stress mining environments, production drill rigs are often employed for rapid drilling of boreholes for systematic cable bolting. One outcome of this drilling method is the need for larger boreholes than would normally be drilled using customised bolting machines, such as the Tamrock Cabolter. Past laboratory studies indicate that, under ideal grouting conditions, borehole diameter has little effect on the pull-out strength of cable bolts with high bulb densities. However, the sensitivity of pull-out strength to large boreholes and less ideal variations of grout strength have not been investigated. To explore these sensitivities, industry standard single embedment tests were conducted on large boreholes simulated using steel pipes. Four borehole diameters were tested, namely: 42 mm, 52 mm, 81 mm and 106 mm. In each case the grout water to cement ratio was varied from 0.35 to 0.45 and two cable bolt bulb spacings were considered, namely: one and three bulbs per metre. The results indicate that, across the range of parameters tested, variations in peak axial load at failure corresponding to changes in hole diameter were statistically insignificant.

Nov 25, 2010

By S O. Hille

Modern remote mining operations in Australia are more commonly trending towards fly-in/fly-out (FIFO) sites. This trend is driven by numerous factors including increased business centralisation, reduction in operating costs, and a desire to live in coastal cities that offer closer family networks and a greater diversity of facilities. Consequently, the resource development industry has had to adapt. When WMCÆs Mount Keith Nickel Operation commenced operations in 1994, it was developed as FIFO for its entire workforce. Since then, there have been several permutations of rosters within a 21 day compressed work cycle including the 14/7 cycle. This paper discusses a case study of the change in management process to the 9/5 work cycle focusing on minimising fatigue in the workplace. It includes the discussion of the business case, employee reaction and the practical application. The impact of the best practice change after 18 months is discussed.

Jan 1, 2002

It is a sad commentary on human nature that for every successful, unscrupulous entrepreneur you need a multitude of incautious, greedy investors. One wonders whether is will be ever possible to completely protect investors from their reckless gambling instincts, which are so widely encouraged elsewhere in society.

Jan 1, 1989

By R Kjar

Globally, it is anticipated that the mineral sands industry will enter a period of short supply. Demand for both titanium dioxide and zircon is forecast to continue increasing, with new projects needed to come on-stream to fill the supply gap. Victoria is well placed under this scenario as a source due to the high quality of its mineral assemblage, its excellent resource grade and the globally significant size of its mineral sands resources.Australia’s mineral sands rich Murray Basin remains under-developed, especially at its extensive Victorian margins. Development to date has not progressed adequately for the reasons of technology difficulty, history of competition with other jurisdictions and the absence of a platform that requires development as a consideration for security of tenure. Victoria’s mineral sands potential is not just about the Murray Basin, in addition, there have been discoveries in the Gippsland Basin and prospective sites in the Gippsland Basin remain under-explored. Key problems included the lack of available ground for potential developers and the intellectual property of solutions to technological problems associated with the fine grained mineral deposits belonging to a previous developer (with patents now expired).As such, the timing is right to re-visit the potential of the Murray Basin as a site for long-term development with high returns based on current and predicted prices.In order to understand why Victoria’s earth resources in general, and mineral sands in particular, remain under-explored and undeveloped, the Department of Primary Industries initiated an internal review of its role in encouraging and supporting investment in the earth resources sector.As a result, the Victorian Government has committed to taking action to encourage effective ground turnover and acknowledges that a new focus on engagement with industry is needed to bring new investment to the State. The revision of the Mineral Resources (Sustainable Development) Act 1990 provides an opportunity for the government to better align its legislative processes with industry project lifecycles and facilitate access to valuable resources that currently remain undeveloped.Victoria has a track record in assisting projects reach development stage. Iluka currently has two operations in the State in addition to its mineral separation plant that is capable of processing HMC from its South Australian operations. Iluka is expected to ramp up its Murray Basin Stage 2 operations with the WRP mine scheduled to come on line in early 2012. Meanwhile, Astron is actively seeking partners for its Donald Mineral Sands project. The project is becoming increasingly attractive given the recent price hike in zircon; Astron has access to an estimated five to 6 Mt of zircon in its Donald WIM 250 deposit.Given its substantial and valuable mineral sands endowments, the State of Victoria should sensibly be the centre of future investment in project development. However, as previously mentioned this is currently not the case. The Government is therefore committed to implementing new measures that protect security of tenure but ensure that genuine companies can access endowments where they have a clear intent to work those resources.

Oct 5, 2011

In March 2003, Rio Tinto Coal AustraliaÆs (RTCA) new Hail Creek open cut coal mine commenced operations in the Bowen Basin. Hail Creek is a two-seam strip mining operation utilising two 90 m3 draglines and a fleet of excavators and trucks to remove the overburden. All overburden at Hail Creek is blasted prior to excavation. The mine conducts its own drill and blast operations while engaging Dyno Nobel for the provision of explosives supply and loading truck (bulk explosives vehicle û BEV) services. This arrangement was favoured over outsourcing the entire blasting function to a contractor. Subsequent to a value engineering review, the mine set about developing and implementing a blasting operation that did not rely on the need to store bulk quantities of ammonium nitrate on site. There were advantages identified in doing this, in particular the reduction of capital expenditure required and reduced exposure to a number of recently introduced security requirements. This approach also makes sense operationally. The establishment of reload facilities for the BEV close to the blasting location, where turnaround times are kept to a minimum, increases the productivity of the BEV. For this strategy to be successful the logistics of ammonium nitrate supply into the blasting operations has to be well planned and thoroughly executed. This means a robust planning and forecasting arrangement needs to be established with the supplier and transporters of the ammonium nitrate. To date, 80 million bcm of overburden has been blasted at Hail Creek and each year the quantity of overburden requiring blasting is increasing. The purpose of this paper is to present the findings of a study: evaluating the effectiveness to date of the strategy to conduct blasting operations without ammonium nitrate storage on site, and identifying whether there is a limit to which this strategy can operate after which the introduction of bulk ammonium nitrate storage facilities are necessary.

Jan 1, 2007

By B P. Micke

Central Norseman Gold Corporation was established in 1935 and has been mining on the Norseman field in Western Australia since then. It is Australia’s longest continuously operating gold mining operation at nearly 80 years, although it has had its periodic challenges in the intervening years.Over the last 40 years, a series of open pit mines around the Dundas Goldfield have supplied lower cost mill feed to the Phoenix Mill at Norseman from time to time but this has largely come to an end for the foreseeable future. Now that underground ore sources are once again the principal mill feed, there are several challenges to be met for an ongoing profitable operation.During the last 20 years, there have been three different owners and this has affected the manner in which the operations were managed quite significantly. These differing approaches are contrasted and examined in some detail from both the operational and financial aspects.Planning of a downsized operation to ensure sustainable profitability in the future in a mining environment where there has rarely been more than two to four years of reserves ahead of the mill for planning purposes has been a significant challenge. Several of the options examined are described, including alternatives for future mine development.CITATION:Micke, B P, 2014. Managing the margin at Norseman, Western Australia – a case study, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G J. Lyman

The theory of sampling has progressed slowly over the last century. The concepts of correct sampling were known to mining engineers such as D W Brunton in the 19th century. It was recognised early in the 20th century that the Poisson distribution of particles carrying the target analyte was the key to the uncertainties between samples of a given mass. However, no efforts were made until the 1980s to determine the entire sampling distribution as a function of sample mass. The variance of sampling was made clear by Gy and others, but none attempted to determine the entire sample assay density function until J H Venter in South Africa applied the method of characteristic functions to the problem.Venter applied the method to a specific case of very low analyte concentrations in samples of very fine particle size where his assumption of constant sample mass was justified. When his general methodology is applied to the more general problem, it can be shown that the assumption of constant sample mass is no longer justified and leads to some anomalous results for sampling variance. Venter’s method can be expanded to allow for a statistically variable sample mass and to take into account the size distribution of particles that carry no analyte.This paper presents the basis of Venter’s work and shows how the approach can be easily modified to yield results for the variance that are consistent, for example, with the work of Gy. It is also demonstrated that the entire sampling distribution can be determined without undue computational burden when sufficient information on the material heterogeneity has been collected.CITATION:Lyman, G J, 2014. Determination of the complete sampling distribution for a particulate material, in Proceedings Sampling 2014 , pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By P Craig, A Crosky, P C. Hagan, E Elias, B Hebblewhite, S Saydam, D Vandermaat

"Premature failure of rock bolts has been recorded at twelve underground coalmines over the past 15 years in Australia. Over the last four years, UNSW Australia has been conducting an Australian Research Council (ARC) and Industry funded linkage research project into premature failure of rock bolts. The extent of the problem was investigated by underground surveys of mines with known prematurely failed bolts using visual mapping, non-destructive load and ultrasound testing. A major component of this project was to define the environmental factors responsible for corrosion of rock bolts. The environment to which a rock bolt is exposed will include groundwater chemistry, the mineralogy of the strata, atmosphere within the drill hole and even microbial activity. This paper focuses on the groundwater survey and analysis findings to date along with in-hole bolt corrosion coupons installed into field sites. Corrosivity classification systems exist for general corrosion but do not apply to the rock bolt stress corrosion cracking (SCC) problem found in Australian underground coal. The method of in situ investigations is leading towards the building of a corrosivity classification model to assist mines in prediction of premature rock bolt failure. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of: helping quantify any corrosivity classification system providing an in situ ground support corrosion monitoring tool for testing possible corrosion protection solutions.CITATION:Craig, P, Saydam, S, Hagan, P C, Hebblewhite, B, Vandermaat, D, Crosky, A and Elias, E, 2014. An investigation of the corrosive impact of groundwater on rock bolts in underground coalmines, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 277–286 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By R Schiller, E Chait

"Quebrada Blanca is a porphyry copper deposit located in the Eocene-Oligocene belt of Chilean Andes. Operation started in 1994 and original reserves for supergene mineralisation gave a life-of-mine (LOM) of 20 years; however, further exploration extended the LOM until 2020.In order to optimise the remaining five years of supergene resource, geometallurgical variables were added to the geological model including copper recovery and acid consumption. LOM plan encompasses finishing the phase number eight and the future development of phases 11 and 13.LOM lithologies include diorites, quartz monzonites, porphyries, igneous and tourmaline breccias. Main alterations are: potassic, phyllic and argillic. Litho-alterations or geometallurgical units were formed by combining five types of rocks with three types of alteration. According to statistical information, the deposit can be represented with 12 litho-alteration units, which cover 98 per cent of the LOM volume.For copper recovery information, there were 40 mini-columns tests made in order to obtain kinetics curves and copper recovery values after comparing the difference between head and tails grades. Acid consumption was obtained using an automatic neutraliser device-based test.Historical data said that copper recovery in pads after 450 days of irrigation is around 75 per cent of recoverable copper while acid consumption is around 5.5 kg/t.According to this study, lower recoveries are related with potassic-altered diorites and argillic-altered quartz monzonites with values around 60 per cent. On the other hand, best recoveries could be found in potassic-altered quartz monzonites and argillic-altered diorites with values closer to 80 per cent.It was also revealed that the most reactive rock is the potassic-altered diorite with 12 kg/t of acid consumption. This rock covers approximately 40 per cent from phases 11 and 13.The final geomet model was calculated using a program that relates each geometallurgical unit with a specific copper recovery and acid consumption value. Results found after comparing model-obtained information with historical leached pads data were used to validate the model.CITATION:Chait, E and Schiller, R, 2016. Adding Copper Recovery and Acid Consumption Variables to the Geological Model of Quebrada Blanca, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

"Recognising that the mining industry is wedded to the break-even cut-off grade rather than a cut-off grade that optimises value, the author examines some perils and pitfalls in the use of break-even grades that lead to what the author calls ‘negatively geared ore reserves’.Negatively geared ore reserves occur when a portion of the ore reserves actually has a negative value and is effectively being subsidised by the more profitable portion of the ore reserves. This situation is generally difficult to detect with the level of information available to the public investor. The ore reserves can still be quite profitable in total, but now possess a level of risk that may not be appreciated.The risk profile (financial risk) of a negatively geared ore reserve is far greater than for a non-negatively geared ore reserve. Like a negatively geared investment property in a falling property market (for readers familiar with the Australian tax minimisation investment strategy), when the price of a commodity falls, a company that possesses a negatively geared ore reserve loses value at a magnified rate relative to a company that has a neutral or positively geared ore reserve. In the extreme case of a major commodity price reduction, as happened with the gold price in mid-2013, the negatively geared ore reserve can easily become negative value in total, not just in part.The negatively geared ore reserve is sometimes intentional – for instance in order to increase published ore reserve tonnages and meet the CEO’s key performance indicators – but is also often unintentional, resulting from various errors in the break-even calculation. Common errors in calculating a break-even grade include using fixed metallurgical recoveries, not including allowances for ideal laboratory versus real plant results, ignoring available operational data and using modal rather than mean parameter values in cost and performance calculations.This paper examines a common value distribution profile in many ore reserves and the effect of common break-even grade errors on this profile.CITATION:Poniewierski, J, 2016. Negatively geared ore reserves – a major peril of the break-even cut-off grade, in Proceedings Project Evaluation 2016, pp 236–247 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006