Search Documents

AT Broken Hill, N.S.W., where flotation is tbe final stage in concentration, the gangue minerals are discharged as an aqueous pulp, and water recovery from the pulp being essential, provision must be made for the clisposal of the solids and for the return of the clear water to the cemcentrating mill circuit. This water also contains an appreciable quantity of flotation reagents, and is more effective for flotation than supply water.In the development of a scheme for the disposal of large quantities of residues, several of the more important factors for consideration are:(a) Tonnage to be handled.(b) Grain size of residues and pulp density.(c) Dewatering of residues and return of clear water to mill circuit.(d) Possible uses of residues.-A varying proportion of sand residues is used for underground filling, and to a limited extent for yoncrete making and other engineering work.(e) Choice of a suitable dumping area. - Before deciding upon this area consideration will be given to possible future operations so that the dump will not be likely to interfere with any development which may be necessary. Again, residues dumped at the present time as worthless or...

Jan 1, 1927

By Moxon N. T

A series of low shock energy water resistant emlulsion based explosives have been developed by combining inert materials, such as Perlite P500, into the formulation. The material handling, water resistance and explosive properties of these mixtures were determined as a function of inert additive type, density, charge diameter and emulsion base. Of the emulsion bases tested Emulite produced the best and most stable low density mixtures ranging in density from 0.8 to 1.35 g/cm3 producing velocity of detonations (unconfined) ranging from 3000 to 5500 nits. The mixtures could be detonated successfully at these densities at diameters as low as 25mm. Low shock mixtures formed by combining Emulite with Perlite P500 were successfully trailed at the Cadjebut zinc mine in Western Australia. The performance of the explosive, at three densities, was monitored using both continuous and point to point VOD techniques. The fragmentation produced by the blasts were compared by photographic analysis. During this trial the low shock emulsion mixtures were shown to be as effective as the currently used explosives (packaged emulsion) at a significantly reduced cost.

Jan 1, 1990

The continuous casting of zinc alloys has been of fundamental importance for many years in the production of a number of products, including sheet for architectural applications, battery cans for dry cells and wire for metallising. The intrinsic benefits of continuous casting, including efficiency and high tonnage capability, uniformity of metallurgical structure and properties, and absence of voids and other defects, have contributed to the success of these products. Less well known, but of growing importance, is the more recent application of continuous casting technology to the production of zinc alloy bar stock products, including bearing stock, machining bar stock, forging stock and cathodic protection anodes. A wide range of zinc alloys are now continuously cast in a variety of cross sectional shapes and sizes to suit the diverse characteristics of these products. Of particular significance are the introduction of hollow zinc-aluminum bearing stock, and the availability of zinc alloy machining bar stock for hydraulic applications and for producing prototypes of zinc alloy pressure die castings. In addition to the traditional benefits, continuous casting provides special properties which are important in the application of these bar stock products. The list of successful applications of continuously cast zinc alloy bar stock is growing rapidly, and the market potential for resultant new zinc applications appears to be significant.

Jan 1, 1993

By Hodkinson I, Teale GS

Mount Leyshon is an open cut-heap leaching operation that commenced production in early 1987. Open pit reserves are 6.3 m.t. grading 1.8 g/t Au and 4.8 g/t Ag and expected annual production is 68,000 oz. of gold. Gold mineralisation is hosted in breccias, porphyry plugs and basement rocks interpreted as the roots of a multi-phase Permian phreatomagmatic breccia complex. Mineralisation has the form of veins, cavity fillings and disseminations and is localised by late stage trachytic dikes and sills and dike-like bodies of milled breccia in the northwest corner of the complex. The sequence of mineralisation includes: I quartz-chalcopyrite-molybdenite stockwork veins and pyrite-gold veins with potassic alteration II quartz-chlorite-carbonate-basemetal sulphide-gold veins and cavity fillings with sericitic alteration III quartz-basemetal sulphide-bismuth-sulphide -electrum veins, veinlets and dissemin- ations with sericitic alteration. Mineralisation is interpreted to have formed at 500-300¦C from a predominantly magmatic hydrothermal system related to the porphyry intrusive bodies. Mount Leyshon is a phreatomagmatic breccia with a very different origin to the Kidston magmatic hydrothermal breccia. However the mineralisation style and origin is quite similar.

Jan 1, 1987

In order that the processes seen may be followed in their proper 'order, the subject will be dealt with as follows, (1) Wallaroo and Moonta Mines; (2) Wallaroo and Moonta Mines Smelting Works; (3) Broken Hill Mines; (4) Concentration at Broken Hill; (5) Smelting and refining of Lead, Silver, and Gold at Port Pirie. The first acquaintance with the copper region was made at the Yelta shaft and dressing mill of the Parramatta Copper Mines Co. at Moonta. The country rock at Moonta is a hard, tough, felsitic porphyry, the copper lodes having a general strike of N. 30° Kilipping from 500 to 70°. This necessitates shaft-sinking on the lode, and underlay shafts are the rule on the field. The ore is raised in the Yelta shaft in wheeled skips, and consists of ·chalcopyrite, bornite, pseudomorphic hematite, containing, in addition, molybdenite and tourmaline. The ore from the bins at the brace is passed over a grizzly; the over-size is hand-picked into smelting ore, concentrating ore, and waste rock (00 attle ), which is sent below for filling. The under-size is elevated to a trommel having in. holes. The over-size falls on to a picking belt made up of lengths of rope strapped with iron, working over wooden pulleys.

Jan 1, 1907

Nauru Phosphate, which is one of the world's highest grade deposits discovered to date, contributed in 1969, 2.2 million tons of the total world production of 77.7 million tons. Phosphate production, which is the major source of revenue for the island nation, is carried out by the Nauru Phosphate Corporation, headed by a Government appointed Board of Directors. The complete mining operation, including ship loading techniques, is discussed along with proposals at present being investigated to upgrade the Quality of the product.

Jan 1, 1971

By Finlayson E, Hilyard D, Francis G

Papua New Guinea's mainland is dominated by a foreland thrust belt, which can be divided into two zones. The "body" zone is floored by Palaeozoic granites and metamorphics of the Fly Platform (Tasman Orogen). Underlying the "tail" zone is Papuan Plateau, rifted from the Tasman Orogen during Coral Sea spreading, and believed to underlie the Papuan Peninsula and Papuan Islands region (D'Entrecasteaux, Woodlark, Misima, Sudest, and Rossel Islands). Thrusting began in the Miocene and continues today in the crust below the "body" zone. The youngest known thrusted rocks in the "tail" zone are Pliocene in age. Recognition of foreland thrusting has major implications for petroleum prospectivity of the Papuan and North New Guinea Basins, mineral exploration prospectivity, and geological terrane identification in PNG.

Jan 1, 1987

By Lorenzen L, Van Der P F

It is the aim of this paper to review recent research in understanding the role of cyanide in the elution of gold. Under conditions of severe pre-treatment (high temperatures and levels of cyanide), the dynamics of elution are determined mainly by the adsorption equilibrium and the flow conditions in the column. When conditions are less favourable for desorption, transport phenomena are rate controlling. The most important sub-processes of elution are the changes in cyanide, potassium and gold concentrations, as well as the change in passivation of the carbon surface. Mathematical models to simulate the various sub-processes are described briefly.The presence of an irreversibly adsorbed species such as AuCN on the carbon is determined mainly by the pH, temperature and the type of carbon. Cyanide in the pre-treatment step will convert the AuCN to reversibly adsorbed Au(CN)2. Competition between cyanide and Au(CN)z for adsorption sites will enhance the elution of gold, but plays a minor role at elevated temperatures. The most important effect of cyanide is its reaction with the functional groups on the carbon to passivate the surface for the adsorption of anionic metal cyanides and thereby promote the elution of gold. This passivation, caused by the degradation of cyanide, is strongly temperature dependent. Free cyanide in the elution step of an AARL elution is of lesser importance than the cyanide in the pre-treatment step. Elution without cyanide is possible only after cold acid washing, and has been proven on plant scale.

Jan 1, 1992

Recognition is the most important aspect in the use of breccias as an exploration tool. Ore-hosting breccias occur in a wide variety of environ-ments, shapes, compositions and characteristics, but generally present favorable loci for the deposition of ore mineralization in epithermal, porphyry copper-gold-molybdenum, massive sulfide, carbonate-hosted, sedimentary lead-zinc deposits and others.

Jan 1, 1990

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

By G I. Lumley

‘Every mine is a pilot’ is an attitude which encourages the mining paradox of optimistic mine plans and equipment under performance; propped up by an environment lacking accountability. The premise that ‘every mine is a pilot’, appears to underlie the development and operating approach to most mines. It is the hypothesis of this paper that many mining companies, development teams and their managers largely ignore what is done elsewhere. Anecdotally, most planners don’t know whether the selected rates are high or low (rates based on theoretical models tend to be high – certainly higher than what most companies can achieve). Mines then consistently operate the equipment at rates well below targets; often more than 20 per cent below. Further to this paradox, mine performance data demonstrates the average mine is currently operating their equipment at levels of output not much more than half the output of those in the top ten per cent. On the whole mines don’t know the potential of their equipment and therefore don’t put appropriate plans in place to do better. After all, when ‘every mine is a pilot’ there is little reason to look to one’s peers for an indication of potential. This paper will outline why every mine is not a pilot and how mines do value some knowledge, but not as much as they should. This paper proposes a two-pronged approach to address this issue in the area of equipment performance. This approach is to:1. engage in better forecasting of equipment rates and better subsequent performance through benchmarking against industry standards2. provide conditions for more accountability.These parameters are linked and proper implementation of them will address the losses which many shareholders and financiers have incurred when investing in companies with unrealistic mining plans.CITATION:Lumley, G I, 2016. Is every mine a pilot? In Proceedings International Mine Management Conference, pp 75-88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By J Schrank

Double-stack trains in the United States date back to the early 1980s, starting about the time deregulation of the rail industry occurred. Freight rail became increasingly more competitive to trucking and barge or ship, and led to major investments in railroad infrastructure. Since most railroad tunnels in the United States were constructed between 1880 and 1930, they were not built tall enough to accommodate modern double-stack intermodal railcars. Therefore, as double-stack trains became the norm, existing tunnels became bottlenecks, and railroads wanted the tunnels made larger without impacting traffic. This need to increase the clearance while not impacting rail traffic launched a very specialised industry: the design and construction of replacement lining systems in existing tunnels.Several large multitunnel railroad clearance improvement projects have been completed in the country in the last decade, and they have all been done under ‘live track’ conditions. Live track conditions consist of work windows, often anywhere from four to 12 hours, that are provided to the contractor to complete the construction work. By the end of each work window, the tunnel must be secured so that the railroad can run trains.In addition to improving the clearance, these projects provided the railroads with an opportunity to improve the general condition of the tunnels, including structural, seepage, drainage and icing conditions. This paper discusses the design considerations, tunnel assessments and construction methods used for these live track railroad tunnel projects. Seepage and drainage improvements that were incorporated into the clearance improvement projects are also discussed.CITATION:Schrank, J, 2014. Live track railroad tunnel repair and clearance improvement in the United States, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 619–628 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Sutherland R. A, Rawling K. R

The Nanisivik Mine is located 750 km north of the Arctic Circle at the north end of Baffin Island in the Canadian High Arctic, and has been in production since 1976. The paper describes the regional and local geology and the current mining and mineral processing operations, including recent innovations in each area. The Nanisivik zinc-lead deposits comprise Mississippi Valley type sulphides in a block-faulted sediment sequence of Proterozoic age. The deposits formed in two mineralizing stages by replacement of the carbonate host rock. Exploration techniques adapted to the permafrost environment include high frequency EM and ground probing radar. Core drilling is done with calcium chloride brine but trials with heated flushing water indicate potential for cost reduction. The predominant mining method at Nanisivik is room and pillar. Cut and fill is used in some satellites to the main zone. Due to the permafrost, dry drilling is employed in the underground mining. The permafrost enhances ground stability, permitting large underground openings and, as a result, the use of relatively large scale mining equipment. For power conservation, a remote control system for the ventilation fans has reduced mine power costs. The milling of the simple coarse-grained ore in an arctic environment requires special techniques in the design and operation of the plant for materials handling, utilisation of waste heat, reagent selection and tailings disposal. Regulated heavy metal contents in effluents discharged to the sensitive environment are achieved by natural processes. A recent change from sub-aqueous disposal of tailings to beach type deposition within a cell in the tailings area is reviewed. Planning closure of the property presents special problems and an opportunity for innovative techniques. Approximately 25 per cent of the employees at Nanisivik are drawn from the Inuit population of the Canadian Arctic. As the first permanent industrial activity in the High Arctic some innovative approaches to employee relations were required which have resulted in a very stable, culturally mixed community in a remote location.

Jan 1, 1993

Nine case studies are presented to illustrate how risks can be, minimised or quantified during pit optimisation, utilising Whittle Four-D software. Each case study covers a specific problem that has been encountered from a wide variety of pit optimisations. Case A: Maximising profits when the tenement owner is paid a royalty on tonnes processed. Case B: Allocating product prices, rather than a single commodity price during optimisation. Case C: Quantifying processing costs that are affected by penalty elements in the ore. Case D: Exploration expenditures below current pits can be quantified through the use of simulation techniques. Case E: Alternative strategies can be quantified when pits are restricted by tenement boundaries. Case F: Relocation of mine infrastructure that requires large capital expenditures, can be simulated by allocating costs to an area during optimisation. Case G: Evaluating alternative corporate strategies during pit optimisation. Case H: Sensitivity analysis for price, processing cost and mining cost. Case I: Quantifying the advantages of using additional mining capacity during the early periods of mining.

Jan 1, 1994

By Sowerby BD

The CSIRU Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt'/. in field tests at BHP Stockton Borehole Colliery, NSW. Mineral Control Instrumentation Pty Ltd have been licensed to manufacture the capacitance gauges and have installed five commercial units in the coal industry and other industries. Microwave transmission techniques have an advantage over the under-belt capacitance technique in that they are not sensitive to vertical segregation of moisture in coal on the conveyor belt. A laboratory prototype of a microwave transmission gauge has been constructed and tested. Microwave techniques, based on a measurement of attenuation and phase shift, are under development and are expected to be field tested in 1987. These new techniques will enable a wide range of thickness changes to be accommodated. Capacitance and microwave transmission methods are unsuitable for materials of high electrical conductivity, such as coke. CSIRO is therefore developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutron moisture gauges and it is expected to be field tested in 1987.

Jan 1, 1987

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

During the past 18 months a rock mechanics project has been in operation at Renison Limited. The project was established to identify and investigate key problem areas that would affect future production at the Renison mine. An in-house approach was adopted, using shall compact equignent, to investigate ground behaviour. Information on the rock stress field was considered to be particularly important for an understanding of ground behaviour. A high horizontal stress component exists, which enables large flat dipping spans of hanging wall to be opened up, with support being provided by post pillars. The amount of support provided by these post pillars has been found to be low.

Jan 1, 1982

LESLIE BRADFORD GOLDEN JUBILEE ORATION "Not only a metallurgist but a scientist of the highest order" Leslie Bradford and the Australian Metallurgical Industry

Jan 1, 1987

The first hydraulic roof supports were installed underground in 1950s and ever since that time engineering developments have improved the supports in many different ways. However. advances in three main areas, the roof support mechanical design, hydraulic engineering and electronics have ultimately led to the point where, 35 years after that first installation. automation has been achieved and is now commonplace.The history of roof support automation has involved the continual integration of high technology engineering. Thera ate further possibilities for the future which combine to give some idea of the likelihood of there ultimately being a completely manless face.

Jan 1, 1991

By Cocker A

Pre-splitting for smooth highwall formation is conducted in around 75 per cent of surface coal operations within Australia. The CMTE (Centre for Mining Technology and Equipment) in conjunction with BHPAC (BHP Australia Coal) initiated a project to look at pre-splitting and to investigate the notching of blastholes for fracture plane control. The notching was specifically for pre-split initiation and also for discing of the toe of the production holes to minimise coal loss from the top of the coal seam. There are currently a number of factors which are driving the introduction of new pre-splitting technologies and products. The first is the ever increasing bench height being employed in strip mines which require a higher quality wall with less blast damage to maintain stability. Currently depths of 55 metres are common place with depths of 70 - 80 metres fast approaching. The second factor is the introduction of new technologies or methods which require a high quality highwall produced, eg highwall mining. This paper discusses the current state-of-the-art in pre-splitting and the main issues facing successful pre-splitting in the future. The use of a blasthole notching technology to promote fracturing along the pre-split line is also analysed. The review indicates that most pre-splitting challenges in the future can be addressed through better use and developments of current drill and blast technology. It is also concluded that a blasthole notching technique may find niche applications in improving final walls within a surface coal mine, especially where a high quality wall is required. The notched blasthole method may also allow pre-splitting in ground conditions and adverse rock structure which currently cannot be pre-split by existing technology.

Jan 1, 1995