Search Documents

Mine planning typically involves designing an operation to uncover coal with the minimum initial costs with reclamation planning and earthworks being done as an "add on" task. The landform is too steep to remain stable, has no drainage and frequently has areas of excessive acidity or alkalinity. Extensive earthworks are required to reduce grades to an acceptable level and create a drainage system. The flexibility available to the mining engineer to alter the post mining landscape clearly depends on the mining methods. Straight dragline stripping provides virtually no flexibility. However most mining operations over the term of current ten year plans have a substantial pre-strip component. It is this pre-strip material which has the potential to reduce the final reshaping earthworks. The reshaping operation itself is subject to some flexibility with various options being available to re-grade and provide drainage. The full utilisation of this flexibility to minimise earthworks cost should be the aim of reclamation design. ACIRL's current thrust in reclamation is aimed at the integration of mine planning and reclamation earthworks. This involves gathering all environment and agricultural criteria and designing the earth works necessary to produce an acceptable final landform. A key component of our work is the use of computer aided design (CADD) for the design of spoil piles, pre-strip dumps and spoil re-shaping. This approach has been applied to a number of mine sites with earthworks operations covering hundreds of hectares and hundreds of millions of cubic metres volume. We are continuing to provide that consultancy service and at the same time are involved in the development of more sophisticated software tools to apply to reclamation design.

Jan 1, 1991

By Kirkhouse C. B

Soon after the Broken Hill Limited started operations at their Iron and Steel Works at Newcastle, NSW, it was found necessary to install a mill for rolling small merchant bars, rounds, etc.An arrangement of the first mill laid down is shown on Plate 1., Fig. 1. This mill commenced operations on the 18th July, 1917.The feed for this mill was rolled in the existing 18-in. mill and sheared to the lengths required before being delivered to the billet storage yard. The billet storage yard is 90 ft. span, and is served by one 10-ton electric overhead travelling crane. Billets were placed on the billet bed preparatory to being charged into the heating furnace.The heating furnace was of the continuous recuperative with end discharge and had a hearth 40 ft. long by 10 ft. wide. The billets were pushed through the furnace by means of two hydraulic rams, which could either act together and push one row of billets, or act singly and push two rows of billets. This furnace was fired by producer gas from the producers shown on Plate I., Fig. l.The gas was conveyed to the furnace by means of a brick underground flue.

Jan 1, 1935

A comprehensive analysisof rock structures in non-oriented (axially oriented) drillcore is now available (Laing, in press). The system embodies new concepts which better equip the geologist and engineer to deal from the outset with optimising the acquisition of structural information in drillcore, logging, interpreting, and graphically presenting the results. The few existing techniques for determining orientations of structures are augmented by a wide range of new techniques, and all are brought together into two solution types by considering the underlying Euclidean geometries. Analysis of these solution types in terms of what data are required to implement each solution and what assumptions need to be made, leads to strategies which facilitate intelligent design of different drilling programs for blind and outcropping situations. Drillcorc is variably structurally fertile, depending on the number of different structures present. This concept fosters the selective logging only of the more fertile core. Drillholes are also variably fertile, depending on their orientational relationship to the structures in the host rocks. Structural parameters are either vectorial or non-vectorial. Vectorial structures parameters comprise normal structural orientations plus polar vectors like vergence, younging, shear sense and so on. They can be determined by one of two solution types: external solutions, which use an external reference structure to fix the drillcore and thus permit orientation of all structures within that core, and internal solutions, which use orientational data from a selected structure at three or more different drillhole orientation to determine the unique orientation of that structure, without reference to any external structure.

Jan 1, 1990

By Hargraves AJ

Pre-drainage experiments have been conduct- ed at Appin, Cook, John Darling, Leichhardt, Macquarie, Metropolitan and Moura No. 2 Collieries. Appin (550 m deep) experiences particular gas problems in development drivages, and the almost pure CH4 seam gas makes difficult tiro compliance with statutory maxima in intakes and returns. Patterns of 43 mm diameter drain- a,.;e holes drilled ahead and laterally into virgin coal have improved gas conditions in working places and have allowed tolerable advance rates. Cook, Leichhardt, Metropolitan and Moura No,. 2 Collieries have experienced gas and stress phenomena ranging from conical bursts less than one tonne to full scale instantan- -us outbursts of hundreds of tonnes with tens ,f thousands of cubic metres of seam gas. Gas ~Irainage experiments with patterns of holes up a,, 200 mm diameter have been undertaken with ;,;siness monitors on the coal to establish .lative effectiveness. Incremental flows into mg 43 mm diameter boreholes have investigated drainage patterns relative to length, and at comparative incremental flows have nlicated lowered permeability zones at stress ,.,utments. In some CO2 seam gas areas where iammability problems are reduced to perhaps ii, but where outbursts proneness is increased,

Jan 1, 1982

By P F. Hodkiewicz, J de Lacey, M Stewart, R Lane

"Implicit modelling is an approach to spatial modelling in which the distribution of a target variable is described by a unique mathematical function that is derived directly from the underlying data and high-level parametric controls specified by the user. This modelling approach may be applied to discrete variables such as lithology (after converting the discrete codes to numeric values) or to continuous variables such as geochemical grades. This paper discusses the estimation of continuous (grade) variables using implicit modelling.One of the underlying engines of implicit modelling for producing this mathematical function description is the radial basis function (RBF). In essence, the RBF is a weighted sum of functions positioned on each data point. A system of linear equations is solved to derive weights and the coefficients of any underlying drift model coefficients. Once derived, the RBF may be solved for any unsampled point or averaged over any volume to provide an estimate of grade. It is possible, for example, to query the RBF on a regular grid to derive an estimate of block grades. Given the ease of creation of an RBF, and its ability to predict grade, the question arises as to how the grades derived from the solution of an RBF compare with grade estimates derived from conventional geostatistical interpolation methods (eg ordinary kriging (OK)).The purpose of this paper is to describe in lay terms: the basic structure of an RBF the role of parametric choice in the solution of RBFs and how this influences the character of the solution the fundamental similarities and differences between RBFs and conventional geostatistical estimators.Using a high-resolution conditional simulation, we show that in many situations RBF and OK estimates are very similar.CITATION:Stewart, M, de Lacey, J, Hodkiewicz, P F and Lane, R, 2014. Grade estimation from radial basis functions – how does it compare with conventional geostatistical estimation?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 129–140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Bartosiewicz H

A method for the determination of the gas content of coal seams is presented which improves upon existing methods. The method makes use of a gravitational technique for measurement of the gas desorbed. The amount of lost gas is estimated by determining an empirical relationship relating the desorption of gas with time for each sample separately. This is to replace the assumption that desorp- tion follows a square root law with time. Laboratory investigations have been conducted which indicate that the square root desorption law does not hold good for carbon dioxide. Results of investigations on various factors influencing the technique are presented. It is shown that co-efficients of the empirical equation are dependent upon the elapsed time and the period of observation. Data about gas pressure measurements is presented and it is concluded that gas pressure can be approxi- mated to 0.6 times the pressure below a column of water equal to the depth of cover. This estimate is good enough for adsorption tests to evaluate desorption co-efficients. The technique for repressurisation of the sample,

Jan 1, 1982

By Savage E. N

The porphyry copper minerals of Melanesia occur within a host of narrow veinlets in predominantly quartz diorite stocks or as contact metasomatic masses in skarns adjacent to the intrusion. Some 90 per cent of the constituent minerals comprise pyrite or marcasite, chalcopyrite, and magnetite with the remainder mainly bornite and hematite with accessory rutile and chalcocite together with several trace minerals. Gold is found mainly as inclusions in chalcopyrite, and minor molybdenite occurs likewise.Of particular significance is the persistent occurrence of accessory rutile of hydrothermal origin intimately intergrown with chalcopyrite. The rutile occurs relatively late in the hydrothermal sequence and upon weathering of the deposit may be released on a cumulative basis possibly in sufficient amounts to constitute a particulate pathfinder mineral which may aid in prospecting.Rutile is present in all the Melanesian occurrences studied and is also prominent in several American deposits.The porphyry copper mineralogy is characterized by the presence of accessory hydrothermal rutile intergrown with chalcopyrite.

Jan 1, 1975

By C Laming, P M. Hetherington, F A. Pym, M P. Murphy, K E. Crook

Reconciliation is a powerful tool used by mining operations to compare the mass and grade of ore produced with what was estimated before mining. The primary objective of reconciliation is to verify that the estimated planned metal production is achieved during processing, allowing issues to be identified for which adjustments can be made throughout the mining value chain to improve recovery and maximise efficiency. Traditionally, the mine plan is based on estimated mine grades using sampled exploration drill hole or blasthole grades. Reconciliation discrepancies between the mine plan and mill are common due to such factors as insufficient or non-representative sampling, poorly conceived models, or unrecognised blast movement. MineSense Technologies Limited® (MTL) has developed an X-ray fluorescence (XRF) sensor-based ore classification system that is installed on mining equipment to provide real-time grade estimates of run-of-mine material at bucket, truck, or belt-scale. Bucket level grade estimates provide insights into grade variations at the mine face that were never before available. This data set eliminates some of the leading causes of reconciliation discrepancies and enables tracking of tonnages and grades from the mine face to the processing plant at bucket resolution with confidence. Bucket-by-bucket grades at the mine face enable dynamic optimisation of the mine plan to stabilise the mill feed grade through blending of mine and stockpile loads. Beyond stabilising feed grade, Mine to Mill reconciliation combined with the full XRF spectrum response can generate proxy relationships to ore characteristics like hardness and recovery. These properties can then be predicted at the mine face, enabling further optimisation of the downstream mill feed, not only for grade, but also for power and water consumption, reagent addition, and recovery. This paper presents the benefits of MTL technology for grade reconciliation and mill performance optimisation at a Cu Mine in BC (Canada).

Mar 22, 2022

By M Fritz, B Ziegelaar

"For moisture samples, the International Standard for iron ore sampling states the following: Moisture samples shall be processed as soon as possible and test portions weighed immediately. If this is not possible, samples shall be stored in non-absorbent airtight containers with a minimum of free air space to minimise any change in moisture content, but should be prepared without delay. ISO 3082 (2009)Prescribing what to do is of course easy. Putting it in practice is, however, a little more problematic.The iron ore industry has seen quite some changes in the last ten to 15 years, such as: a large increase in the volume of seaborne trade new ore types and blends coming onto the market new mines, processing plants and port facilities producing more and loading faster an increase in wet processed ore products a dramatic rise and then equally dramatic fall in the iron ore price followed by a recent recovery.All of the above have had an effect on sampling facilities. The large increase in volume coupled with ambitions such as labour efficiency, safer operations and higher precision has driven the installation and retrofitting of automated sampling and robotic sampling preparation plants in order to keep up with increased quality control.Designers of sampling facilities are invariably instructed to build plants that comply with ISO 3082. In general this means that the plants are compliant in respect of the number of primary increments, gross sample masses and sample division rules. The clause at the beginning of this abstract is mostly overlooked as it only appears in a section (4.1) describing the basic requirements of a sampling system.An error of 0.1 per cent in moisture changes the value of 1 Mt of iron ore at US$50/t by US$50 000. At 700 Mt/a of Australian iron ore exports, this is US$35 M. Frequently, errors from 0.5 to 1 per cent in moisture measurements are encountered.In comparison an error of 0.1 per cent Fe is US$0.081 (US$50/t and 62 per cent Fe base) per tonne, that is US$81 000 per Mt or about US$51 M for the same Australian annual iron ore exports.It is somewhat mystifying that we in the ISO Technical committees spend extraordinary energy (= money and time) on improving measurement techniques, whilst the big costs are in sampling errors. This is particularly true for moisture measurement. Our paper quantifies some of the sources of moisture measurements errors and suggests mitigating actions.CITATION:Ziegelaar, B and Fritz, M, 2017. Sampling for the percentage moisture in the iron ore industry, in Proceedings Eighth World Conference on Sampling and Blending, pp 271–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

Among countries afflicted with insLantaneous outbursts of coal and gas, Australia is noteworthy because of lesser disturbances of the seams and of the occurrence of CO2 in the seam gas from place to place. Research sLarted with the 1954 occurrences at Collinsville and Metropolitan Collieries leading to early publications reviewing the problem, describing occurrences and assessing variations in proneness factors in the two affected coal basins.The basic requirements for proneness include coals of high gas sorptive capacity, high ground stress, use of a mining method which provides higher stress concentrations and limits emission of seam gas, including high rates of advance. With CO2 in the seam gas proneness is greater.The mechanism is complex and not fully understood, but involves the coal, the roof, the floor, the gas, the mine opening, the ventilation, the kind of work and the rate of work. Geological disturbances such as faults and dykes increase proneness and tend to localise occurrences. On-occurrence of outbursts in some mines is difficult to explain.Outbursts are seen as a continuing threat to modem deep Australian mining of high rank coal.The simplest contributory factor to reduce is gassiness - despite the low permeability of outbursting coals - and present practices are showing promise. The greatest challenges for the future are partial degasification to below a known threshold figure and confirmation that this reduction is achieved and identification of anomalous geological structures ahead, the most likely locations for instantaneous outbursts to occur. The advances made to date give promise of a future with reducing experiences of uncontrolled instantaneous outbursts. For the Bulli seam particularly, working to achieve prediction and prevention is most urgent.

Jan 1, 1993

By D R. Seaman, R P. Tooher, B A. Seaman

"Several mine scheduling tools exist for use in optimising and scheduling the reserve according to in situ value. These tools generally value the ore on a per block basis according to regressed recovery models based on ore grade and type. It is then the task of the plant metallurgist to ensure that these ore blocks are fed to the plant in a manner that satisfies the prevailing plant constraints. This task is often completed in complex Excel® spreadsheets that are modified over time with factors applied to account for plant modifications or limitations.It is the authors’ experience that this approach is difficult to audit and replicate in a consistent manner. Furthermore, operational decisions, such as primary grind size or autoclave oxidation are made on the metallurgist or managements’ perceived optimum value and does not necessarily represent a cash flow based optimum.Many processing plants contain multiple internal constraints. As ore feed grades and properties change over the life-of-mine (LOM), processing-bottlenecks shift from one unit process to another and different operating strategies need to be adopted to maximise cash generation from the process.This paper presents a unified optimisation approach to scheduling ore based on a circuit mass balance to describe the process plant with individual models for each significant unit operation. The approach allows for optimisation over multiple input variables and the inclusion of linear and non-linear constraints.This optimisation process has been applied to different complex gold operations. The end result is an automated scheduler that selects the optimum blend of ores as well as plant operating conditions that satisfy all internal plant and shutdown constraints while maximising the objective of choice (metal production or cash flow). The models are also valuable for evaluating expansion or debottlenecking opportunities of individual processing units. These models are coded in Matlab® R2016a provided by MathWorks®, and can be deployed to end users in a compiled version with significant savings in time to run different scenarios over the Excel®-based systems.Citation:Seaman, D R, Tooher, R P and Seaman, B A, 2016. Optimisation of Complex Gold Processing Plants with Multiple Unit Operation Constraints - the Newcrest Planning Scheduler, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By L Lachance, F Flament, D Leroux, S Gariépy

The pervasiveness of poor sampling practices in and around mineral processing plants could seem intriguing in view of the various documented evidences both for causes and consequences. To this extent, this paper revisits the well-documented but lesser-known fact that failure to care sufficiently about how samples are selected and managed is the mother source of almost all sampling biases. The authors believe that the potentially huge leverage between causes and consequences as well as the diversity of people involved in sampling call for a globally integrated solution rather than for a point solution. Such a globally integrated solution has already been put forward by the AMIRA P754 Metal accounting – code of practice and guidelines (AMIRA, 2007) that inherently requires accuracy to be targeted, measured, reported and managed. Furthermore, always in order to avoid a point solution, several layers of protection against biases must be put in place with each one involving a different ownership whenever possible. This is exactly the role intended by the supervisory bias detection method described in this publication. It is based on the continuous monitoring of the expected value of reduced residuals obtained from statistical data reconciliation conducted in a metal accounting context. This supervisory bias detection method is developed in full details after which Monte Carlo simulations are done on a mineral processing plant example for showing how it can be successfully applied for detecting hidden biases.CITATION:Lachance, L, Leroux, D, Gariépy, S and Flament, F, 2014. Detecting sampling biases in metal accounting, in Proceedings Sampling 2014 , pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By S Tierney, D Cumming-Potvin, I Thin, Y Potvin, D Grant

The preliminary modifying factors for future stope design in the Southern Mine Area of Olympic Dam consisted of only a single, arbitrary value of Equivalent Linear Overbreak/Sloughing (ELOS). In order to improve this, a study was conducted which developed a more comprehensive methodology for assigning ELOS, Equivalent Linear Lost Ore (ELLO) and Equivalent Linear Fill Overbreak (ELFO) to individual stope faces based on geotechnical and mining parameters. The approach used was to look at the simple cases, which were classed as vertical stope walls in good ground (RQD 80-100%), divided into wall orientations (North, South, East, West). The stope walls were also split based on the blasting practice used (toeing, parallel or a combination of the two). The expected ELOS and ELLO from these ‘base cases’ are then modified by parameters which have historically been found to affect stope performance (Hydraulic Radius and Q’). The size of the effect found in the historical data determines the ELOS / ELLO applied. The methodology was summarised in an easy to use flow chart and was applied to all of the proposed stope shapes for the Southern Mine Area and summarised per mining block. This allowed each iteration of the mine plan to be assessed in terms of overbreak (both rock and vertical fill exposures) and underbreak.

Mar 15, 2021

By J P. Sykes, C Gemell, A Trench

The perceived and actual impact of government mineral policy upon the government share from gold mining revenues is assessed for ten key countries in which the gold sector is of relevance in advancing economic growth. Five African and five South American jurisdictions are considered, namely Burkina Faso, Ghana, Mali, South Africa and Tanzania from Africa; and Brazil, Chile, Colombia, Guyana and Peru in South America.Both the headline corporate income tax rate and royalty level are identified as poor indicators for the total government share. In addition, significant differences between industry perception and actual government tax levels are identified by this study. The quantitative financial analysis shows that there is no clear relationship between individual taxation rates, taken in isolation, and the overall average effective tax rate (AETR) paid by the project over its life. Neither companies nor governments should use individual taxation rates, or industry perceptions, in isolation to assess the overall competitiveness or equity of a country’s minerals taxation regime – such analysis can be very misleading.In this study, the perceived impact is determined from the well-established Fraser Institute survey published each year, and in 2014 compared 122 minerals jurisdictions globally. The actual impact is determined from quantitative modelling of the financial performance of a hypothetical gold mining project in each country. The technical parameters of the project are held constant; instead the differing mineral policies in each jurisdiction are applied to determine the resultant impact upon the relative share of the economic rents delivered to both private and public sectors. In the quantitative analysis, the total government share varies from 36.3 per cent in South Africa to 66.5 per cent in Ghana.CITATION:Gemell, C, Sykes, J P and Trench, A, 2016. Is perception reality? Evaluating the fiscal attractiveness of international jurisdictions for gold mining investment, in Proceedings International Mine Management Conference, pp 227-238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By J Ashford, Minniakhmetov

Geostatistical simulations are the best practice for uncertainty quantification in non-linear systems. Simulations are currently undertaken on an ad hoc basis in the mining industry due to high requirements in computing environments and advanced geostatistics. In contrast to the estimation process, multivariate simulations can be performed using different methods, tools, and computational environments, similar to data science. For large companies with multiple commodities it is important to have a standard framework to test, build, and run workflows using different methods, applications and computational environments. This work presents an auditable, modular and scalable framework to create geostatistical simulation workflows where the workflow is abstracted from the implementation. Key aspects: automation – workflows should be able to run automatically given updated data (if hands on modelling is not required); auditability – workflows should document key considerations and parameters; modularisation – workflows should permit swapping out components, for example substituting domaining in Leapfrog software with automated domaining using machine learning scripts; scalability – easy, repeatable, portable deployments on diverse infrastructure (for example, experimenting on a laptop, then moving to an on premise cluster or to the Cloud); reproducibility – parameters should be archived to permit re-running and reproduction of workflows in future years; and sensitivity analysis – any component of a workflow should be able to run with multiple scenarios of parameters and data to enable global uncertainty quantification and sensitivity analysis. The presented framework can be used to create different workflows for geostatistical simulations in multiple assets to quantify uncertainty in the value chain for resource categorisation, reserves uncertainty, value of information and robust mine planning amongst others.

Mar 22, 2022

The sinking of the new No. 3 Shaft being mainly concerned with providing for the continuation of mining operations north of the existing workings, requirements for the shaft and haulage equipment were assessed, having in mind the anticipated needs of the Company in future years, the .available knowledge and probable future trends of the orebody, and also that the shaft would be required to act as a downcast airway for the ventilation system associated with the northern underground workings.

Jan 1, 1957

By J Carrillo, A King

Gravity recoverable gold (GRG) is largely distinguished from other gold by its non-mineralised, metallic form, its high degree of liberation from the ore and its appreciable particle size. The gold mining industry has so widely accepted the use of batch centrifugal concentrators (BCC) and intensive cyanidation (IC) systems for the recovery of GRG that these may well be considered requirements of any plant processing ore containing appreciable GRG. The recovery of gold by gravity is quick, easy and cheap by comparison to alternatives. However, there are cases where attributes of the ore make recovery of gold by gravity and IC unusually challenging. This paper describes three examples where such challenges have been encountered and met, including those where the ore contains cyanide soluble base metals and where fine GRG is to be recovered from flotation concentrate.CITATION:King, A and Carrillo, J, 2018. Addressing challenging applications of intensive cyanidation in gravity gold recovery, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 283–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Misra A

After review of the status of research on optirnisation of retreat longwall faces it is argued that an acceptable optimisation model must be based upon realistic cost data that take into account not only the face costs, but the total panel costs. These include the cost of development, face cost, removal and installation cost. The determined optimum length of a retreat longwall face is based upon a realistic model and actual costs.Parameters that influence the optimum face length have been varied over wide limits to allow determination of the sensitivity of the model and the effect of the parameters on the optimum face length. It is concluded that for medium production rates and medium system availability, the optimum face length of a retreat longwall face under Australian conditions lies between 180 and 220 metres.

Jan 1, 1995