Search Documents

By G. Willard Quick

FAILURES in railroad rails have been of vital concern to engineers; railroad executives, rail manufacturers and the general public for years. Failures from transverse fissures originating from internal nuclei have received particular attention in the past 20 years. Dr. J. E. Howard first reported this type of failure in 1911, as being responsible for a wreck-on the Lehigh Valley R. R. in which several lives were lost. Since then many transverse fissures have been found. In 1919, Waring and Hofammann1 etched longitudinal sections of rails in hot acid and found cracks extending both longitudinally and transversely in certain used rails as well as in some new rails.. Since then it has been thought by many that these "shatter" cracks are the nuclei from which transverse fissures subsequently develop in service. Methods for reducing the rate of cooling rails on the hot. bed have been devised to decrease the temperature gradient and consequently the stress gradient in the rails. A study of the tensile properties of rails at elevated temperatures was made by Freeman and Quick,2 who investigated the properties at temperatures through which rails pass on the cooling bed after leaving the hot saw. In their investigation a special study was made of the ductility of the steels in the temperature range 400° to 700° C. In this temperature range it was found that certain rail and other steels showed a marked decrease in elongation and reduction of area. The phenomenon was called "secondary brittleness" and the temperature range the "secondary brittle range." A tentative explanation was presented that internal failure such as "shatter cracks" and "hair cracks" in rails are the result of thermal stresses developed in the steel structure while cooling through the secondary brittle range. The investigation showed that the magnitude of the phenomenon varies for different heats, but that it did not differ for specimens from different ingots or for different rails in a particular ingot. It was also shown that annealing rail steel at a temperature either above or below the critical

Jan 1, 1932

By Philip Bucky

THE general conception of a mine model is that of a three-dimensional object representing the mine workings, the orebody and the country rock of a particular property. Its chief uses have been to make it easier to understand the mine and to serve as a basis for the arguing of legal questions. Fayol endeavored to use mine models in a different way and to all students of subsidence "Fayol's dome theory" is of decided interest. We have more recently the suggestion of Young and Stoek of the University of Illinois, who1 suggest the use of models as a means of studying the problem. Prof. Henry Briggs, of the University of Edinburgh and Herriott Watt College, also makes use of models to determine the effects of bending at the edges of extensive workings.2 It is interesting to note that civil engineers are taking a decided interest in the application of models and the principles of dynamic similarity to the solution of their problems. The Proceedings of the American Society of Civil Engineers for 1930 contain an elaborate article by Benjamin F. Groat,3 who says, in his opening remarks: "Every engineer should know and understand that a model constructed in accordance with Newton's theory of similarity is not only the means for reproducing the complexities of flow, or other mechanical action, on a small scale, but that models may be made the best means of designing works of great magnitude. In the present state of knowledge, a properly constructed and properly tested model will answer the difficult questions of hydrodynamics much more quickly and accurately than the most profound mathematical analyses." A study of P. W. Bridgman's book on Dimensional Analyses leads one to arrive at the same conclusion.

Jan 1, 1931

By J. B. Cheatham, C. E. Murphey

Presently, computer control of Borobolic direction cannot be obtained during drilling, and most straight-holc drilling methods attempt to resist hole deviation rather than control direction. Many of the theories advanced as possible explanations of the cause of hole deviation are Summarized berein. A new correlation of physical partables is introduced to indicate bow factors such iis drill collar stiffness clearance and hit weight influence borehole deviation, .A methord is proposed for predicting the rate of change of hole angle when drilling conditions are changed. INTRODUCTION Control of borehole direction during drilling can be difficult and costly. Unintentional crooked holes are often lrilleti in dipping formations and many times directional drilling is required when the surface location is not directly above the target area —- for example, at offshore and mountainous locations. Prilllng progress can be greatly hindered in either air or liquid drilling when it be comes necessary to use low bit weight to prevent excessive hole angle build-up. If hole inclination becomes too great, drill pipe drag becomes excessive and fishing risks are increased, logging is more difficult and problems of differential sticking, key seating and fatigue failures may be encountered. Dog-legs and key seats are more serious problems than steep inclination angles: therefore, reducing rate of direction change is preferred to attempting to maintain absolutely vertical holes. Consequently, a straight inclineti hole is preferable to a nearly vertical crooked hole containing numerous dog-legs. In this paper, theories of the cause of hole deviation and analyses of drill string behavior under down-hole conclitions are summarized. Methods for computing hole deviation are presented und systems for resisting deviation as well as neans for provic!ing control of holt- direction are iliscusseI. A new correlation of physical variables is introduced tu indicate how factors such as drill collar stiffness, clearance and bit weight influence borehole deviation. A method is oroposeti for predicting the rate of change of hole anFrle when drilling conditions are clianged. IIEVIEU' OF PREVIOUS WORK ON HOIaE DEVIATION Significant progress in the theoretical analysis of hole deviation problems has been made in the past 1 5 years. The pioneering work has been primarily a result of the efforts of Lubinski and Woods.l-5 In 1950, Lubinski 1 considered the buckling of a drill string in a straig:rt vertical hole, a problem also considered by Willers6 in 1941. It wns concluded that very low bit weights must be used to prevent hole deviation resulting from drill collar buckling. The use of conventional stabilizers was proposed2 in 1951 by Mac Donald and Lubinski as a method for permitting greater Sit weights to he carried without drill collar buckling. These authors pointed out that a 2° nearly vertical spiral hole can cause severe key seatinp, and drill pine near, wilereas n 3 straight inclined hole with deviation all in one direction, while not vertical, will not result in serious drillirig or producing problems. Studies were continued with an investigation of straight inclined holes by Lubinski and Woods3 in 1953. In this paper they concluded that perfectlv vertical holes cannot be drilled even in isotropic forriations unless extremely low bit P-eights are used. .l'l~ey postulated that constant drilling conditions produce holes of constant inclination angle and varying conditions cause the hole to drill at a neiv equilibrium angle. This analysis was not concerned with drill string buckling since it was based on an equilibrium solution in which the ~irill string Was presumed to lie along the lower side of the hole abcrve the point of tangency. Weight of the drill collars below the point of tangency tends to force the hole toyard the vertical, whereas the weight on hit tends to force the hole aurav from the vertica l. The concept of an anisotropic formation Lvas introduced as an empirical method for explaining actual drilling data and as a means for extrapolating known deviation data to otiier conditions of hit

Jan 1, 1967

By Gerard Matthes

Only in recent years has any practical headway been made in the application of aerial photography to geological problems, and up to the present time its principal value to the geologist and mining engineer has been in "areal geology;" i. e., the study of formations as revealed at the surface. The object of this paper is to set forth briefly the principal advantages that may be derived from aerial photographic data in geological work and to serve in a measure as a guide to those who may be contemplating its use. Geophysical prospecting has for object the locating of mineral under the surface. Inasmuch as the geologist's chief complaint in life is a dual one—inability to see under the surface and inability to visualize comprehensively what he does see on top of the ground—geophysical prospecting coupled with aerial photography should do much to lessen his burdens. To what extent aerial photography can be made a useful adjunct to geophysical prospecting remains to be proved, but the inference drawn here is that it holds many alluring possibilities. To avoid disappointments, it should be stated at the outset that to the geologist or mining engineer an aerial photograph or mosaic is only a tool, the efficient use of which he must set out to master. Upon his skill and ingenuity in applying it to particular problems will depend largely the value of the results that he will obtain. Under the most favorable conditions an aerial mosaic, or even a few loose photographs, because of the exceptionally comprehensive oversight which they afford of field data, such as dips and strike observations at isolated outcrops, local indications of faulting, mineral and fossil finds, greatly facilitate study and correlation, save much tedious foot work, and may repay their cost many times. Even so, types of country may be found where the most skillful use of the best of pictures will produce results so meager as to render the cost of aerial photography entirely unwarranted. Between these two extremes will be found endless variations and possibilities. Hence no set rules can be promulgated. The safest procedure is to treat each case as a separate problem and to carefully weigh the relative advantages and shortcomings of aerial photography before embarking on its use.

Jan 1, 1928

By R. Van A. Mills

ONE of the most important problems facing the petroleum industry is the profitable recovery of oil that is left underground by the ordinary methods of production. It is true that vast quantities of oil are being recovered from fields previously considered depleted by the pressure restoration method, the most widely applicable -and most successful means of obtaining greater recoveries that has thus far been, developed. But notwithstanding the progress that is being made in the field applica¬tion of this method there is urgent need for a better understanding of the fundamental principles that are involved. To meet this need the Petro¬leum Experiment Station of the U. S. Bureau of Mines at Bartlesville, Okla., during the past two years has conducted a series of intensive laboratory and field investigations. The larger part of the work has been carried on in the laboratory to supply the much needed information upon fundamental principles, information which few if any of the oil companies are in a position to supply for themselves. In all of this work the Bureau is endeavoring to correlate the results of laboratory investigations with those in the field, using the results of one to guide or check the other. This paper is primarily a progress report, briefly outlining the Bureau's methods of study, the laboratory and equipment in use, the preliminary problems that had to be solved in order to attack the major problems at hand, the methods of attacking some of the major problems, and some of the results of the investigations to date.

Jan 1, 1928

By R. L. Slobod, C. Gatlin

This .study defines the basic mechanism of the mis-cible displacerrzent of oil and writer from porous Medici by various water-driven alcohol .slugs. Three distinct alcohol slug processes were .studied. Considerable data concerning the quanity of alcohol required for oil recovery were also obtained. All data were obtained in a 1-in. diameter, 100-ft long, unconsolidated core. The porosity of this system was 35 per cent. and the permeability was approxitrlately 4 darcies. Total core pore volume wax 5,716 cc. All displacements were conducted at a constant injection rate of 5 to 6 cc//min, which corresponds to a frontal advance of 5 ro 6 ft/hr. The first portion of this paper is concerned with 111 use of one alcohol—isopropyl—a\. the slug material. Isopropyl alcohol (IPA) is completely miscible with both oil rind water; however, miscibility of the threc-component systems, oil-water-IPA, requires a relutively. high concentration of IPA. Hence, the displocement is not of the misoible type unless the IPA concentration is maintained above some critical value. A slug of IPA equal to only 13.5 per cent of the pore volume was jound to be sufficient to obtain complete recover?, of residua1 naphtha. In later studies two distinct process variations were developed. The firsr of these utilized methyl alcohol (MA) and IPA as slug materials. It was shown that methyl alcohol may he substituted for IPA at the front and rear of the slug with no loss of oil recovery. A .slug of 4 per cent MA-4 per cent IPA-4 per cent MA was sufficient for complere oil recovery. Because MA is considerably cheaper than IPA, this represents an important step toward economic application. A .second process variation used normal butyl alcohol (nBA) and MA as the composite slug, the nBA segnzent being injected first. This technique requires the smallest total slug size (approximately 10 per cent) of all processes studied. The high cost of nBA, however, precludes commercial application. It is possible that this basic process, subject to changes of alcohol type, may lead to a commrercicil process. INTRODUCTION Within the last 10 years, considerable study has been devoted to the general mechanics of miscible phase dis- placements in porous media. These studies have. in general, dealt with two-component displacernent. All reported field trials to date have been modified gas drives of one type or another. These utilize either lean gas at high pressure, rich gas at lower pressure or an LPG slug. The irreducible water content of the reservoir remains immobile during these processes. Although these techniques hold great promise. certain drawbacks do exist. Poor areal sweep efficiency, inherent in any displacement having a highly unfavorable mobility ratio, is one disadvantage. Furthermore, the miscibility of all processes which use gas is dependent on pressure. These pressure limitations may prohibit application to shallow reservoirs. There are also many areas where large quantities of LPG and natural gas are not readily available. These factors emphasize the need for improved techniques. The alcohol slug process is also a miscible-phase displacement process. It differs from the previously mentioned two-component techniques, however, in that both the reservoir oil and water are displaced by the slug. This behavior is a consequence of the miscibility of certain oil-water-alcohol systems. In the simplest case, a relatively small volume (slug) of an alcohol (such as isopropyl) is injected into the system. Water is then used to drive the slug through the medium. Thus. three components—-alcohol. oil and connate water-—exist at the front side of the slug. Miscibility is obtained at some alcohol concentration, this being dependent on the solubility of the particular system. Miscibility is maintained within the slug until the alcohol concentration falls below that value required to maintain miscibility. When miscibility is lost, the process reverts to a water flood. Certain inherent benefits of this technique are apparent. High pressures are not necessary to obtain miscibility in these liquid systems. Furthermore, water is a more desirable driving agent than gas because of the improved mobility ratio and the attendant improvement in areal sweep efficiency. The main disadvantage is, of course, the relatively high cost of alcohols. The use of an alcohol slug to recover reservoir oil is not a new idea." ' However, this process has received only limited study, presumably due to the lack of industrial interest caused by the seemingly prohibitive cost of alcohols. The main purpose of this study was to investigate the mechanism of the displacement of oil and water by various alcohol slugs and to develop process modifications aimed toward possible commercial application.

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By O. D. Gonzalez

Existing measurements for the steady-state permeation of hydrogen in a iron above 100°C have been examined for contribution of determinate errors. The analysis leads to a recommended equation for the permeability of hydrogen in a iron: o= (2.9 ±0.5) x 10-3 exp - (8400 ± 400)/RT cu cm (ntp H2) cm-1 sec-1 atm-1/2 THE permeability of a iron to hydrogen has been the subject of numerous investigations over the past 40 years, and at present there are thirteen sets of published results for the rate of steady-state permeation of hydrogen in a iron above 100°C. The numerical values in each set of results are entirely self-consis-tent, but the spread among the sets is too large to be attributed solely to experimental error, i.e., to error other than in the specimen itself. Several reasons have been advanced to explain the disparities, but to date the relative importance of experimental inaccuracy to the spread remains uncertain. The purpose of this report is to examine in detail the sources of determinate errors inherent in the experiments and to assess as far as possible the contribution of the errors to the results. The ultimate goal is the selection of values for the permeability and heat of permeation most nearly representative of hydrogen in a iron. The analysis is limited to those experiments in which the permeation rate was observed at steady state—a condition in which traps for hydrogen within the metal are filled to a fixed level15 so that the trapping mechanism is not reflected in the rate of passage of the gas. Furthermore only data are examined in which surface processes are judged to have little or no influence on the flow. It is hoped with these restrictions to obtain values of the permeability and the heat of permeation which will be as closely related as possible to the mechanism of lattice diffusion. I) DEFINITION OF TERMS; UNITS In this report the data for permeation are given in terms of a coefficient oj permeability, ?, which is defined by the equation: jt=?A/?x{p1/2-po1/2) [1] where jt is the total flow of gas normal to the surface of a membrane of planar geometry, e.g., a disc, of area A and thickness ?x; pi and po are the pressures in the input and output sides, respectively. For flow radial to the walls of a membrane of cylindrical geometry, e.g., a tube, the corresponding equation is: where 1 is the length of the cylinder, and ri and ro are the inner and outer radii, respectively. The flux normal to the surface is given by Fick's law: j= -D(dc/dx) [3] At steady state the concentration gradient will be constant, and integration of Eq. [3] gives for the total flow through a disc of area A and thickness Ax: h =-DA(co - ci) [4] where c, and ci are the concentrations of solute at the output and input surfaces, respectively. When surface control is absent, co and ci are given by Sievert's law c = Kp1/2, and substitution therewith into Eq. [4] gives directly Eq. [I] where ? = DK. Integration of Fick's Eq. [3] in cylindrical coordinates will give Eq. [2] where again ? = DK and is thus shown to be independent of geometry (provided that surface control is negligible). The coefficient of permeability, or simply the permeability,* must be expressed in proper units. In *The term permeability will refer in this report always to the coefficient defined above; permeation will be used to specify the general phenomenon of gas passage through a membrane. this report ? will be expressed in the units of cu cm (ntp H2) cm-1 sec-1 atm-1/2. The variations of D and K with temperature are given by D = Do exp(-Ea/RT) and K = KO exp(-?Hs/RT) where E, is the activation energy for diffusion and AH, the heat of solution, each usually expressed in calories per mole of solute. The variation of permeability with temperature will thus be given (for conditions where surface control is negligible) by ? = ?o exp(-?Hp/RT) where ?0 = DoKo and ?Hp = Ea + ?Hs. The units of ?0 are the same as those of 6, and??Hp will be expressed in calories per mole H. 11) SUMMARY OF PERMEABILITY RESULTS Table I gives the values reported to date for the permeability of H2 in a iron in terms of ?o and ?Hp. Except where noted the parameters listed were taken directly from the numbers reported by the various investigators with only a change in units. The temperature limits within which the listed ?o and ?Hp hold are given in column 7; the limits marked in parentheses in this column indicate the entire temperature range covered in each investigation. The listed values of ?o and ?Hp are those giving a linear plot of ln? against T-1 at the higher temperatures in each set of measurements, and thus presumably represent the case for which surface control was negligible. Column 6 gives values of 9 at a representative tem-

Jan 1, 1970

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By Richard R. Zupp, David A. Stevenson

An experimental method to determine the carbon activity in various solid solutions was developed. Samples of the solid solutions and an Fe-C reference sample were equilibrated with respect to carbon content by annealing them in a Hz-CHI gas mixture in a closed cell. The carbon content of each sample was determined, and the carbon activity was obtained from the carbon content of' the reference sample and well-established data for the dependence of the carbon activity on the carbon content in Fe-C alloys. The influence of vanadium on the activity of carbon in austenitic Fe-C-V alloys at 1000°C was determined by this technique. A general semiempirical correlation was developed to describe the dependence of the activity coefficient of- carbon on the composition of ternary austenitic iron-base alloys containing interstitial carbon and a substitutional solute. The correlation is particularly useful in predicting the partitioning of- carbon between various alloys. THE influence of substitutional solutes on the activity of interstitial solutes in metallic solid solutions is important in the theory of alloy phases. Solid solutions of particular interest are the fcc austenite phases of ternary Fe-C-Z systems, in which carbon is the interstitial solute and Z represents any substitutional solute. Carbon-activity data are also needed in these solid solutions to solve practical problems; the quantitative treatment of diffusion-controlled transformations' is an examvle. Experimental information is available for ternary austenitic solid solutions containing Mn,2 Si,2 and A16 as the substitutional solute. Because qualitative preliminary studies indicated that vanadium appreciably decreases the carbon activity,14 the present investigation was undertaken to determine the influence of vanadium on the activity of carbon in austenite. Although Flender and ever" measured carbon activity over a range of compositions in the Fe-C-V system, they were primarily interested in determining phase boundaries in the ternary system, so most of their measurements were outside the composition range for stability of single-phase austenite. Petrova and Shvartsman' also made limited measurements of the carbon activity in Fe-C-V alloys. The dependence of the carbon activity on the carbon content of an alloy may be determined by passing COCOz or H2-CH4 gas mixtures of carefully measured composition over the alloys, determining their equilibrium carbon content, and utilizing the relevant equilibrium relationships. smith16 used this technique with both CO-COZ and HZ-CH4 gas mixtures to determine the dependence of carbon activity on carbon content in pure Fe-C alloys. His data, which are in good agreement with those of some previous and subsequent investigators,6'17 but not with those of others,lfl'ao are usually considered to be the most reliable. Although the same method can be applied to Fe-C-Z alloys, it is difficult experimentally, because the appropriate gas mixtures are almost pure CO or Hz. A simpler technique is to simultaneously equilibrate the Fe-C-Z alloys and pure Fe-C alloys with the gas mixtures, and then use Smith's data to determine the carbon activity in the pure Fe-C alloy. A number of investigators have employed this technique. others Have used the partitioning of carbon at the interface of a diffusion couple prepared from an Fe-C alloy and a Fe-C-Z alloy. In the present study, a closed-cell method was developed by which carbon was selectively transferred via a gas medium between pure Fe-C alloys and Fe-C-V alloys which were not in physical contact. A similar method was developed independently by Heckler and winchel14 and used to study the Fe-C-Ni system. EXPERIMENTAL METHOD A schematic diagram of the experimental arrangement is shown in Fig. 1. In a typical experiment, a 5-g Fe-C sample was placed in one compartment of a quartz cell, and a 5-g Fe-V sample was placed in each of the other compartments. The cell was evacuated, outgassed, backfilled with approximately 125 Torr of hydrogen, and sealed. After being placed in a fur-

Jan 1, 1967

By J. Sharshall Grasty, Thomas L. Watson

The users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the material in that region. The domestic production is derived from Missouri .and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral. General Character Barite, known commercially as barytes or heavy spar, is barium sulphate (Baso4), containing when pure BaO, 65.7 per cent., and S03, 34.3 per cent. The specific gravity is 4.3 to 4.6, and the hardness 2.5

Jan 1, 1915

By Alexander Field

The hot-rolling properties of a series of high-sulfur steels are described. From a consideration of the sulfur, manganese, and zirconium contents of these steels, it is shown that zirconium reacts with the sulfur content of molten steel in accordance with the equation Zr + 2S = ZrS2. Zirconium disulfide appears in the finished state as gray-colored inclusions, similar to manganese sulfide in plastic behavior and general appearance. Zirconium completes its act of deoxidation before proceeding to combine with sulfur and indirectly increases the effective sulfur-combining power of any manganese which may be present. IN A previous paper,1 the experimental methods used and some of the results obtained in an extensive investigation of steels containing zirconium were described. The present paper considers in greater detail one of the most interesting of these effects, namely, the elimination of "red shortness" and the occurrence in steel of a compound of zirconium and sulfur. A consideration of the actual percentages of zirconium, manganese, and sulfur in numerous steels in the light of behavior during rolling has led to new conclusions of the most practical import regarding the reciprocal relationships of these elements. The microscopic examination of high-sulfur steels containing zirconium has also been productive of interesting results. Before discussing the experimental data in question, it may be stated, briefly, that the reaction between zirconium and sulfur in molten steel may he represented by the simple equation, Zr + 2S = ZrS2, and that the zirconium sulfide thus formed occurs in the finished steel in the form of gray-colored inclusions, closely resembling manganese sulfide and, like the latter, exhibiting plasticity at rolling temperatures. Molten steel containing zirconium retains such a negligibly small amount of oxygen in solution that the foregoing reaction goes to completion.

Jan 2, 1924

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

By A. Grant Elliot, H. W. Lavendel

qualitative picture has been developed to describe the oxidation behavior of TaSi2-coated tantalum and CbSi2-coated columbium. These systems have a significantly lower inherent oxidation resistance than MoSi2-coated molybdenum does. This stems primarily from the fact that Ta2O5 and Cb2O5 are nearly as stable thermodynamically as SiO2, whereas MoO2 or Moos are not. Further, diffusion of silicon in the Ta- and Cb-Si system is considerably slower than in the Mo-Si system. These ,factors prohibit the mechanism of selective oxidation of- silicon which accounts for the oxidation resistance 01- MoSi2-coated molybdenum. The silicide can be stabilized by adding suitable Modifiers which increase the thermodynamic stability of the silicate formed during oxidation. Modifiers, such as aluminum, can be inroduced into solid solution in the coating. in controlled amounts through proper selection of the source in the pack cementation process of coating fov~rzatiorz. Addition of aluminum to TaSi2, coatings on tantalum was effective in moderately increasing the oxidation resistance. EXTENSIVE experimental work and analysis have established the nature of the oxidation behavior exhibited by MoSi2- and MoSi2 -coated molybdenum-base alloys, and defined the conditions for maximum protection against oxidation of the substrate.'-* The oxidation resistance of MoSi2 in the temperature-pressure range of 1100°C-PO2 > 10-5 atm to 1900°C— PO2 > 10-1 atm is due to the formation at the surface of a continuous film of SiO2 which results from selective oxidation of silicon. Under the prevailing kinetic conditions, this film is stable toward the molybdenum silicide with which it comes in contact. Initially molybdenum oxidizes also, but it forms volatile species. SiO2, however, nucleates and grows as a condensed phase. Once a continuous film of SiO2 has formed, the oxidation rate falls to that observed for the oxidation of pure silicon indicative of diffusion through the oxide film as the rate-controlling mechanism. This oxidation behavior is of course highly dependent upon temperature and oxygen pressure. Bartlett and Gage13 and Bartlett, McCamont, and Gagelb define precisely this dependence in terms of the oxygen partial pressures and silicon diffusivities required to support a stable SiO2 film. At low temperatures (near 500°C—the "pest" region) silicon diffuses too slowly to be selectively oxidized. Hence, molybdenum and silicon oxidize readily in proportion to their stoi- chiometry. At high temperatures and low pressure, SiOz dissociates to form volatile SiO(g), and a protective film cannot be maintained. Application of the MoSiz/Mo system is limited to temperatures below 1900oC, the eutectic between MoSi, and MO5Si3.5 The oxidation behavior of MoSi2-coated molybdenum is essentially the same as that outlined above with the exception that the MoSi2 is not in equilibrium with the molybdenum substrate. At the temperatures under consideration silicon will diffuse rapidly into the molybdenum eventually converting the coating to MosSi3.4 The rate constant for subsequent decomposition of Mo5Si3 into Mo3Si plus silicon, and/or the diffusivity of silicon through Mo3Si then becomes low enough to allow active oxidation of both molybdenum and silicon with subsequent degradation of the specimen. A stable silica film can be formed but at temperatures and/or oxygen partial pressures higher than those required with MoSi2 present as a source of si1icon.l, 4 Because of the similarity between the silicides of molybdenum and those of columbium and tantalum one would expect similar oxidation behavior for coatings in the respective systems. This is not entirely the case, however, as shown by the experimental results reported herein. Regarding tantalum and columbium disilicide coatings on tantalum and columbium substrates, respectively, the oxygen arriving at the surface of the coating partitions itself nearly equally between the metal and the silicon, and a two-phase oxide layer (Me2O5 plus SiO2) is always formed. The diffusion of silicon in the tantalum and columbium silicides is relatively slow, compared to that in the molybdenum silicides, which further enhances this equipartitioning of oxygen. Thickening of the coating during service by inward diffusion of silicon into the substrate is correspondingly slow, and the effective thickness of the coating at the roots of cracks and defects is only slightly changed providing high probability for premature coating failure. Furthermore, the SiO2 glass that is generated is not thermodynamically stable with respect to the coating. The metal silicide tends to reduce the SiO2 liberating either free silicon or SiO. The situation can be improved by suitably modifying the coating such that the stability of the protective glass which is generated during service is increased. Thus, selective oxidation of silicon and the modifying agent will occur, and the silicide coating will not tend to reduce the oxide layer. Modifying agents can be introduced into the coating by the pack cementation process. Using sources containing the modifier at controlled chemical potentials allows control of the coating composition. Partially substituting aluminum for silicon in TaSi2 coatings by forming a Ta(Si,Al)2 solid solution was effective in moderately increasing the oxidation protection.

Jan 1, 1968

By I. R. Kramer

Studies of the effect of size of the specimen on the change of slopes of Stages I and 11 by surface removal showed that the change of Stage I was independent of size with respect to the polishing rate; however, the change in the slope of Stage 11 with polishing rate increased directly in proportion to the surface area. The removal of the surface during the test affected the plastic deformation characteristics of gold, aluminum, and zinc single crystals and polycrystalline aluminum. The apparent activation energy of aluminum was found to be decreased markedly by removing the surface during the deformation process. In previous papers1-3 it was shown that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing during tensile deformation, it was found that the slopes of Stages I, II, and III were decreased and the extents of Stages I and II were increased when the rate of metal removal was increased. By removing a sufficient amount of the surface layer after a specimen had been deformed into the Stage I region, upon reloading, the flow stress was the same as the original critical resolved shear stress and the extent of Stage I was the same as if the specimen had not been deformed previously. The slope of Stage I was decreased 50 pct and that of Stage 11 decreased 25 pct when the rate of metal removal was 50 X 10"5 ipm. These data show that in Stage I the work hardening is controlled almost entirely by the surface conditions, while in Stages 11 and III both surface conditions and internal obstacles to dislocation motion are important. It appears that during the egress of dislocations from the crystal, a fraction of them becomes stuck or trapped in the surface regions and a layer of a high dislocation concentration is formed. This layer would not only impede the motion of dislocations, but would provide a barrier against which dislocations may pile up. In this case, there will be a stress, opposite to that of the applied stress, imposed on the dislocation source and dislocations moving in the region beyond this layer. It has been found convenient to refer to this layer as a "debris" layer. The "debris" layer may be similar to the dislocation tangle observed by thin-film electron microscope techniques.4 Reported in this paper are the results of studies on the effects of removing the surface during plastic deformation on aluminum crystals of various sizes. The effects of the surface on the yield point behavior of gold and high-purity aluminum crystals as well as the creep behavior were also determined. The effects of surface removal on polycrystalline aluminum (1100-0 and 7075-T6) are also reported. EXPERIMENTAL PROCEDURE For those portions of the investigation involving creep and tensile specimens, single crystals, having a 3-in. gage length and a nominal 1/8-in. sq cross section, were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The single crystals were prepared from materials which had initial purities of 99.997, 99.999, 99.999, and 99.999 pct for Al, Cu, Zn, and Au, respectively. The aluminum specimens for the size effect studies were prepared through the use of a three-tier mold in which crystals having a cross section of 1/8, 1/4, and 1/2 in. were grown from a common seed. The mold design was arranged so that one 1/2-in. crystal, two 1/4-in. crystals, and four 1/8-in, crystals of the same orientation could be cast. With this technique, it was possible to obtain only one set of crystals with the same orientation. Because of this limitation, it was not possible to determine both the changes of extent and slope of the various stages since a large number of crystals of the same orientation would have been required. Instead, only the change of slope as a function of the rate of metal removal was studied by abruptly altering the current density of the electrolytic polishing bath at various strains within the regions of Stages I and 11. The experimental techniques used for the tensile studies were essentially the same as those used previously.1,3 The specimens were deformed in a 200-lb Instron tensile machine, usually at a rate of 10-5 sec-5. A methyl alcohol-nitric acid solution was used as the polishing bath for aluminum. The temperature was maintained constant within ±0.l°C by means of a water bath. The tensile machine was

Jan 1, 1963

By C. A. Stewart

PAGE. I. Introduction............ 241 II. Location. TopoGRaphy. and History....... 243 III. DescRiption of the Rocks......... 245 1. Altered Sediments.......... 245 2. Alaskite........... 246 3. Alaskite.Porphyry.....255 4. Quartz Dikes........... 257 5. Biotite.Granite.......... 256 6. Quartz.Porphyryl......... 260 7. Andesite........... 262 8. Miscellaneous Dikes......... 263 IV. Age oF the Rocks and Comparison with other Localities.. 263 V. AlteRation............ 265 1. Sericitization........... 265 2. Silicification........... 266 VI. StRuctuRes........267 1. Dip of the Limestone......... 267 2. Faulting........... 267 VII. Contact - metamorhism,.......... 269 1. Endomorphism.......... 269 2. Exomorphism......... 271 Recrystallization and Loss of Color...... 271 New ,Minerals.......... 272 Addition of Material........ 274 Volume.Changes.... 276 Locus of Metamorhism........ 277 Method of Precipitation.........278 VIII. ORe-Deposits............ 278 1. Contact-Metamorphic Copper.Ores,..... 279 General..........279 Shape and Distribution........ 279 Minerals........... 281 Secondary Enrichment........ 282 2. Disseminated Copper.Ores........ 283 3. Origin of the Copper.Orcs........ 284 4. Lead-Silver Ores.......... 287 IX. Bibliography............ 288

Jan 1, 1913

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By T. A. Wilson, S. L. Hoyt

The plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,' which has become a classic, and also by one of the present authors in a somewhat shorter account. 2 The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been done on single-crystal zinc, but as it is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips3 have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94" removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.