Search Documents

By R. E. Goodman, M. A. Mahtab

The, state of stress around a vertical wellbore in rock following nonlinear stress-strain laws is examined by means of finite element analysis. The wellbore, is considered an axisymmetrier body with axisymmetric loading. The initial vertcal and borizontal stresses are "locked" in the rock elements around the wellbore and a new state of stress is generated by the displacements which occur around the borehole. A point-uise variation of the elastic moduli is made on the basis of the new stress state and the triaxial data. The initial stresses tire now reintroduced along with tile changed moduli and original boundary constraints. This procedure is repeatrd until convergent stresses are reached. The effect of nonlinearity on streases is examined for a 6,000-ft wellbore in a scbistose gnezss and Berea sandstone using results of laborratory triaxial compression tests. The results sbou that the effect is restrited to one well radius from the bottom periphery of the bole. Beyond a distance of one-quarter radius, the elfect of nonlinearity on stresscs IS almost always less than percent for the cases conszdered, The consideration of a static pressure inside the well does not magnify the effect of monlinearity on borehole stresscs. INTRODUCTION The terms " wellbore" and "borehole" here designate cylindrical openings in the ground with vertical axis and a circular cross-section. A knowledge of the stress redistribution that occurs on excavating a wellbore is important in understanding (1) the behavior of the lined or unlined hole, (2) hydraulic fracture response, and (3) the effect of stress redistribution on drillability; also it is important in predicting initial stresses in the virgin ground, and in analyzing the response of measuring instruments placed in the borehole. Our knowledge of the state of stress around a wellbore has been restricted to homogeneous, isotropic, elastic material and derives chiefly from the analysis by Miles and Toppingl and the photoelastic work of Galle and Wilhoit2 and Word and Wilhoit.3 In this investigation the state of stress is examined for a nonlinear elastic material by means of finite element analysis. Many rocks possess stress-strain curves that depart notably from straight lines in their initial or final portions. While the literature contains abundant stress-strain data from triaxial tests (axisymmetric loading) on cylindrical rock specimens, there is little information on rock deformability under nonaxisymmetric loading conditions such as occur at each point around the bottom of a wellbore. Although there is some knowledge of the effect of intermediate principal stress on rock strength, there is virtually nothing known about its effect on rock deformability; therefore, we have assumed here that the effect of intermediate principal stress can be ignored. A schistose gneiss4 and Berea sandstone5 were selected as representative rocks for this analysis. The traditional graphs of deviator stress (ol -o3) vs axial strain were reworked to give the tangent modulus as a function of the deviator stress for varying values of the minor principal stress. The result is a nesting family of skewed, bell-shaped curves for tile gneiss (Fig. 1A) and the sandstone (Fig. 2A). A similar replotting of the lateral strain data defines the variation of Poisson's ratio (v) with the deviator stress and confining pressure. These curves, shown in Fig. 1B for the gneiss and in Fig. 2B for the sandstone, are not so well ordered as the tangent modulus curves. However, all of these display an increase of v with deviator stress application, but the rate of increase diminishes with confinement. The ET and v curves for the two rock types are tabulated in Tables 1A and 1A for use in a digital computer so that material properties corresponding to a given state of stress can be assigned by interpolation. STATEMENT OF THE PROBLEM Given a state of stress in the ground prior to drilling a hole (initial stresses), we assume that

Jan 1, 1969

By James Gayley

The development of blast-furnace practice in America in the direction of large yields is mainly the history of our working since the year 1880, as the advancement that has been made in the last decade is greater than that in the third of a century previous. A new era in the manufactnre of pig-iron began in 1880 with the putting in blast of the Edgar Thomson furnaces. These furnaces at once leaped to the front as pig-iron producers, and have maintained that position—with but one brief interruption—ever since. I shall, therefore, confine myself mainly to a description of these works, showing the changes in design and practice by which these results have been achieved. In order to show more clearly the progress that has been made since 1880, I shall refer briefly to the best work that was done in the ten years previous to that time. The Struthers furnace, in Ohio, was one of the first to attract attention in the matter of large outputs. This furnace was 55 feet high, 16 feet in diameter of bosh, 9 feet in the hearth, and about 8 feet 6 inches at the stock-line. The fuel was raw coal. This furnace, in December, 1871, made 1602

Jan 1, 1891

By K. M. Rolls, J. Wulff, D. A. Colling

Solid-solution alloys of the Ta- Ti system containing up to 70 at. pct Ti were melted and fabricated into wire. Steady magnetic-field measurements of cold-worked wires at 4.2°K indicate that the resistive critical field increases smoothly with increasing titanium, reaching a maximum of 93 kG (J = 1 amp per sq cm) for a composition of about 50 at. pct Ti. The composition dependence of the resistive critical field indicates it is largely paramagnetically limited for alloys containing more than 35 at. pct Ti. For cold-worked wires the value of the critical current density, Jc , was found to be insensitive to composition changes for compositions in excess of 20 at. pct Ti. It was observed that Jc could be increased by final-size heat treatment at 400°C without altering the value of- the resistive critical field. Experimental data are used to calculate the electronic specific-heat coefficient and the "upper critical field" for the alloys studied. THE effect and importance of metallurgical structure on superconducting properties have been summarized by Livingston and Schadler.1 Specific work on solid-solution alloys such as Nb-zr2-7 and Nb-Ti5-7 have shown that critical current density (Jc) and superconducting transition temperature are structure-sensitive. Berlincourt et al.6,8,9 in their studies of transition-metal alloys find that Ta-Ti alloys remain superconducting at fields comparable to Nb-Ti alloys. 6,8 Transverse critical current tests of a Ta-10 at. pct Ti alloy10 and longitudinal critical current tests of a Ta-25 at. pct Ti alloy1' indicate that such alloys are capable of carrying high currents at intermediate fields (-40 kG). The work reported in the present paper was undertaken to explore the superconducting properties of further compositions in the Ta-Ti alloy system as well as the structure sensitivity of the superconducting properties. I) EXPERIMENTAL PROCEDURE Alloys were prepared by melting tantalum (Fansteel Metallurgical Corp., 99.96 pct purity) and iodide, crystal bar titanium (Foote Mineral Co., 99.92 pct purity) mixtures in an arc furnace on a water-cooled copper hearth using a tungsten electrode. Melting was accomplished in a purified, gettered argon atmosphere at pressures from 250 to 400 Torr. Each alloy was turned and remelted fourteen times to assure complete mixing of tantalum and titanium. Ex- cessive coring in the cast samples was, nevertheless, observed. This was somewhat reduced by annealing in vacuo at 1000°C for 13 hr. The ingots were then machined to 0.250 in. diam, jacketed in Type 304 stainless-steel tubing, and swaged to 0.140 in. diam. They were then drawn to 0.010-in.-diam wire. Alloys containing up to 70 at. pct Ti were readily cold-drawn to wire in this manner. Later experiments showed that oxygen additions up to -3000 ppm could also be cold-worked into wire. Test samples for superconductivity measurements in the 2-in, air-core Bitter solenoids of the M.I.T. National Magnet Laboratory were prepared from 10-in. lengths of 0.010-in.-diam wire, cleaned of residual wire-drawing lubricant. Current contacts were made by clamping clean copper tubing over both No. 18 current lead wire and the ultrasonically indium-tinned ends of the specimen wire.12 Potential leads of No. 32 copper wire were connected to the specimen by ultrasonic soldering in an indium bath. The potential lead separation was about 4 cm, corresponding to the circumference of the Bakelite rod to which the wire was affixed with half-mil Teflon tape. The final specimen configuration is shown in Fig. 1. Specimens were lowered into a liquid helium bath (4.2oK) in a double solenoid dewar and positioned so that the maximum magnetic field was oriented transverse to the wire axis of the gage section. Measurements were made by passing a current through the specimen at a preset solenoidal magnetic field. The current was increased until a 1-pv potential difference appeared across the gage section (1/4 µv per cm). At low magnetic fields, however, it was not possible to use this criterion because power-dissipation difficul-

Jan 1, 1967

By Donald H. Beilstein

The St. Joe Minerals Corporation Lead Smelter and Refinery have been in continuous operation at Herculaneum, Missouri since 1892 as the Herculaneum Lead Smelting Division. Over the years, the plant has undergone many changes to increase production, improve the technology, reduce the cost of operations, and produce the highest grade of primary lead. The latest alterations were begun in 1950 and completed in 1970 and have resulted in the Herculaneum Smelter capacity being increased to in excess of 200,000 tons per year (180,000 metric tons). This increase has made the Herculaneum Smelter the largest in the United States, and second largest in the world. This paper will describe the Herculaneum Smelter equipment, processes, and material balances. Particular emphasis will be given to the McDowell-Wellman 10' x 100' (3 x 30 meter) up-draft sinter machine and ancillaries; to the new Heavy Smelting Department (blast furnaces and drossing section); to the new Lead Refinery and its automatic casting equipment and to the gas handling system including the 340 tons per day (305 metric) Sulfuric Acid Plant utilizing a -four pass converter. The description will include photographs, flow sheets, tonnages and assays where applicable.

Jan 1, 1970

By F. W. Lee

Historical-From the beginning of time, all ingenuity of mankind has been concentrated upon the methods of finding gold and unusual deposits in the earth. An illustration (Fig. 1) from the old treatise by Agricola, "De Re Metallica," published in 1580, will serve to show the im-plicit faith of that generation in divining methods. However, it was not until 1920 that real progress was made in prospecting by using the latest advances of the physical sciences. The public interest was stimulated by the successes of these methods on the part of commercial oper-ators, and governmental agencies received many requests for information concerning their relia-bility. There were also, in the late 1920's.high- pressure mine-promotion schemes which used geophysical methods in a very questionable manner, symbolized in Figure 2 as of 1928 by an elec-trified forked stick. Authoritative information concerning such practices for public protection was needed to curb such notorious undertakings. Dr. Scott Turner, then Director of the United States Bureau of Mines, thoroughly understood the situation and was first in the governmental de-partments to recognize the possible value of a study of modern prospecting methods. The Bureau of Mines began this investigation by employing Drs. A. S. Eve and D. A. Keys of McGill University for short periods in the summer in 1927. Their first publication [see 1 of "References" at end of paper] served to illustrate the fundamental scientific principles which underlie geophysical prospecting. This was followed by a second publication [21 giving the results of field-tests. In the light of the rapid improvements during the intervening ten years, these two papers take a historical position. Later a full-time position under Civil Service was planned by the Bureau of Mines for con-tinuous investigations and research concerning geophysics and its applications to prospecting. It was Turner's idea that. since the oil-industry had been making very rapid progress with good results, if mineral mining could also benefit to the same degree, it would be of great help to that industry.

Jan 1, 1940

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By Linda Lee, R. E. Reed-Hill, C. R. Smeal

Four fcc metal surfaces, etched to make them responsive to polarized light, have been studied with an electron microscope. Jones'prediction that these surfaces are grooved has been verified. Optical-goniometer measurements made on commercially pure nickel indicate that the groove walls are poorly defined (100) facets. Surface mientations close to either 4001 or {ill).- show no extinctions on the polam'zid-light microscope. An explanation is offered for this orientation dependence. It has also been deduced that polarized-light extinctions on a grooved cubic-metal surface should not be used directly in crystallographic-orientation determinations. The nature of the etching solutions that produce these surfaces is considered. A cubic-metal surface may be made responsive to polarized light in two basic ways."' In one, an anodic film, believed anisotropic, is formed on the surface. A plane-polarized-light beam, at normal incidence, should be reflected from this type of film with an ellipticity that varies with grain orientation. Under crossed polarizers of a polarized-light microscope, each grain may be distinguished from its neighbors by a difference in reflected-light intensity. An alternate treatment,' more generally applicable to cubic metals and of principal concern here, involves etching of grain surfaces. The characteristic features of this surface were first deduced by Jones3 from light-microscope observations. She concluded that, in general, grain surfaces were furrowed so that light was reflected from two parallel sets of etched facets. A grooved surface produces elliptical polarization of a plane-polarized beam because the beam does not strike groove walls at normal incidence. Jones also observed that the furrows must have faces inclined to each other by approximately 90 deg, since the light returns along the incident path, and that a grooved surface should show four maxima and minima of reflected-light intensity during a 360-deg stage rotation of the polarizing microscope. Positions of maximum extinction were predicted to occur when groove axes were parallel to either polarizer or analyzer vibration directions. Because of the limited resolving power of Jones' optical microscope, her deductions were primarily indirect. Proof of the correctness of her conclu-sions, as demonstrated by the electron microscope, will be given as well as evidence concerning the crystallographic nature of the etch furrows and the types of etching solutions that produce them. EXPERIMENTAL PROCEDURE During a comprehensive study of hot plastic deformation in nickel and nickel alloys, an etch was evolved that produced a surface with an excellent polarized-light response on Nickel 200 ("A" Nickel). The etching solution and associated metal-lographic procedures are given in Table I. In evaluating this etch, a study was made of the topological features of the etched surface and their relation to the underlying crystalline structure. As part of this investigation, large crystals (2 mm average diameter) were grown in a 1-cm-sq Nickel 200 specimen. After the surface was etched, the crystallographic orientations of ten grains were determined by the standard back-reflection Laue technique of Gren-inger.4 Maximum extinction positions during a microscope stage rotation were also measured for the ten grains. Groove-wall positions on the surfaces of the ten grains were measured with a two-circle optical goniometer. The technique was essentially that of Barrett and Levenson.5 Several grain surfaces were photographed with a Philips Model 100A electron microscope. All specimens were replicated with collodion, or collodion backed with formvar and chromium shadowed at 18 to 20 deg. The basic material was Nickel 200. However, an electron-micrographic study was also made of surfaces developed by polarized-light etches on other fcc metals (90-10 a brass, Monel 400, and lead). All etching procedures are given in Tables I and 11. EXPERIMENTAL RESULTS Fig. 1 shows typical electron micrographs of three different fcc metal specimens and an optical micrograph of a fourth. All photographs show a grooved structure corresponding closely to Jones'3 predictions. Also, as noted by Jones, extinctions were always observed when groove axes were either parallel or perpendicular to the microscopes' vertical cross hair. The symmetry of the grooves, with respect to the twin boundaries in Fig. 1, implies that furrows have a crystallographic basis. The coarse-grained Nickel 200 specimen was used to study this basis. Facet Orientation. The poles of the ten Nickel 200

Jan 1, 1964

By Edmund Davenport

Tier; production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium.

Jan 1, 1929

By J. C. Swartz

New measurements of graphite and cementite solubilities in ferrite have been obtained to resolve disagreements among previous data. To measure graphite solubility, specimens of iron were equilibrated with rarious carburizing atmospheres at temperatures be-twee~z 480" and 1435°C. The carbon activity of each atmosphere relative to graphite was taken from published data. After quenching from each equilibration treatment the concentration of carbon (typically 10 pprn by wt) was determined from the height of the Snoek peak in the internal friction spectrum. A few inclividual analyses by combustion support the reszdts of Smith on the solubility of graphite near the eutectoid temperature. Combination of these combustion and internal friction analyses determines In a, (at 0.01 wt pct) = 24,000/RT - 12.72, where a, is the activtity relative to graphite in ferrite at fixed cornposition. The same specimens were used to determine the solubility of self-stressed cementite precipitates. The results indicate solubilities of 6.3, 23.2, and 68 pprn carbon by wt at respectively 400°, 500". and 600°C. The once large discrepancy between the cementite solubility determined by internal frictiori and that calculated from flee energy data has been almost completely resolved. A recent study1 (hereafter designated I) on the solubility of cementite in a iron did not fully resolve the disagreement among previous data. The remaining disagreement is illustrated by the phase diagram in Fig. L The data of I are represented by the line labeled "stress-free" cementite. They determine a heat of solution of cementite of (14.8 * 0.2) kcal per mole which contrasts with the (20 * 1) kcal per mole derived from Smith's graphite solubility2 and the formation energy of cementite.3 Toward resolving this disagreement we have obtained new data on the solubilities of graphite and cementite. METHODS As in I the Snoek peak in the internal friction spectrum was used to measure the concentration of carbon dissolved in ferrite. This method relies on the relation C=kQ-1 [1] in which C is the concentration of dissolved carbon, Q-I is the Snoek peak height, and k is a proportionality factor which is a function of the peak temperature, polycrystalline texture, and other parameters characteristic of the ferrite lattice. To determine true heats of solution via Eq. [1], it is necessary to establish that k is independent of the temperature from which the specimen is quenched. Some evidence on this point is contained in a separate report.* Additional evidence is shown by the data points in Fig. 1. These represent the Snoek peaks of two specimens carburized to about 10 ppm C, copper plated, and quenched first from 888º then from 588°C. The copper plate was removed before each Snoek peak measurement. These data show that there is no detectable dependence of k on quenching temperature. The solubility of graphite was determined by repeatedly carburizing various specimens of iron wire with gas mixtures of known carbon activity relative to graphite. To cover a wide temperature range within the a phase boundaries it is desirable to use as low a carbon concentration as is compatible with reasonable precision. With the present internal friction apparatus the best compromise of these desires is a concentration near 10 wt ppm. The dashed line in Fig. 1 was used to approximate the activity of carbon* for

Jan 1, 1970

By Cyril Smith

A STUDY of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published1 giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. PREPARATION OF ALLOYS The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 percent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2-in. dia. casting, the turnings being separated into three parts according to the position

Jan 1, 1931

Jan 1, 1923

By N. Mungan

Formation damage, i.e.. reduclion in permeability, has been generally attribuled to clay minerals which expand or disperse upon contact with water that is less saline than the connate water. Luboratory, studies show that penneahility reduction can also occur in formalions containing only nonexpandable clays such as illite or kaolinite, and can be caused also by changes in pH. Furthermore, pH changes can damage even formations that are essentially free of clays. It is suggested that permeability reduction is due to the small passages being blocked by particles, which may be dispersed clays, cemenlion material or other fine parricles. These particles are dislodged by dispersion of clays due to changes in salinity or by dissolution of calcareous cement by acids, or of silicaceous cement by alkaline solutions. In working with reservoir cores, it was found that extracted cores damaged more easily and extensively than nonextracted cores. The extent of damage depended also on tenlperatltre. INTRODUCTION Permeability is an important property of porous media and has been the subject of many studies by engineers and geologists. Many of these studies are conccrned with formation damage, i.e., reduction in permeability, resulting from exposure of oil-producing formations to water substantially less saline than the connate water. This effect causes understandable concern since during drilling, completion and production phases formations are often exposed to fresh water. The damage resulting from contact with relatively fresh water has been attributed to expansion and dispersion oF clay minerals. During laboratory investigation of the use of NaOH as a wettability reversal agent to increase oil recovery from oil-wet reservoirs, several cores used in the displacement studies suffered loss in permeability. Despite the traditional usage of NaOH for conditioning aqueous mud systems, the role of the caustic filtrate in wellbore damage seems to have been overlooked. Browning2 as recently reported on the effects of NaOH in dispersing clay minerals but he was concerned only with complications that may arise in drilling massive shale beds. The following study was made to examine the role of pH and salinity changes in core damage. Where cores from reservoirs were used, tests were performed with extracted and nonextracted cores both at room and reser- voir temperatures, since it was felt that the test environment and core condition may affect the results. Because of its limited coverage and exploratory nature, this study is not intended to provide answers to field formation damage problems. It is hoped that it will encourage research into new aspects of the permeability reduction problems, particularly those allied to new recovery and production processes. PROCEDURE In all permeability tests, fluids were pumped through the cores at a constant volumetric rate. Only deaerated fluids and reagent grade chemicals were used. The fluids were passed through two ultrafine filters before injection to remove any entrained particles. The cores, with the exception of the unconsolidated cores, were mounted in Hassler holders. Water was used to transmit pressure to the sleeve. The inlet endpiece had two entry ports which permitted scavenging one fluid with another to avoid any mixing in the small holdup volume. The cores were flushed with CO2 gas, evacuated for 5 to 6 hours and saturated with the first liquid at a pressure of 1,000 psi for 24 hours to eliminate any free gas from the cores. Pressure differences up to 20 psi were measured by transducers, calibrated in inches of water and continuously recorded. For greater pressure drops, gauges were used. All reservoir cores were cleaned with a light refined mineral oil, then with heptane, and finally dried with CO2. Compatibility tests showed that no precipitates formed when mineral oil and the crudes were mixed. Some cores were extracted in Dean-Stark-type solvent extractors using xylene and trichloroethane and dried in a vacuum oven at 450F. Each test consisted of a sequence of water, test solution, and again water flow. RESULTS AND DISCUSSION STUDIES IN BEREA CORES Salinity Contrast Berea cores 2-in. in diameter and 12-in. long were cut from sandstone quarried in Cleveland, Ohio. The clay minerals were identified by X-ray diffraction to be chlorite, kaolinite, illite and incerlayered illite. Flow of fresh water or 30,000 ppm brinc does not cause any permeability reduction (Fig. 1). However, after injection of brine the core is readily damaged by fresh water. Damage starts almost instantly as the fresh water injection is begun, and at a cumulative injection of 1.2 PV fresh water, the permeability has dropped from 190 to 0.9 md. Upon continued injection, the effluent contains clay minerals dislodged from the core. The final core per-

Jan 1, 1966

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.'j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?' for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4'5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,' is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel's work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969

By R. S. French

The purpose of this paper is to present data that have been obtained during the past two years concerning the effects of prior cold-work and temperature and time of anneal upon the recrystallization and grain growth of 70-30 cartridge brass. It was desirable to study certain of these phases so that an accurate picture of the principles of the subject could be shown. The work is not intended to provide explicit annealing data, but to provide material examples that may help to clarify analogous problems concerning this alloy. Specifications often set limitations upon the grain size of annealed materials because of the importance of grain size upon subsequent manufacturing operations. It was, therefore, worth while to study the variables that affect the recrystallized grain size of this material. C. H. Mathewson and A. Phillips,l W. R, Webster,2 and others have presented annealing characteristic curves of this alloy. A recent typical curve presented by R. S. Pratt3 is shown in Fig. I. The tensile properties and grain sizes are shown as functions of the annealing temperature. Such curves serve as a useful guide in determining the physical properties of annealed material, but as they are made generally under carefully controlled laboratory conditions they do not indicate the performance of metal annealed in a mill muffle, where such conditions as amounts of metal, heating time and temperature may differ. Study of the effect of time and temperature upon grain growth and subscquent recrystallization was made with a coil of metal having the following analysis: 70.04 per cent copper; 0.007 lead; 0.007 iron; 0.00 tin; 0.00 silicon; 0.001 nickel; 0.000 phosphorus; balance zinc. The sample coil was obtained from metal that had been rerolled from hot-rolled mill stock, and was received at 0.228-in. gauge, soft, with a grain size of 0.125 mm. This material was then rolled 43.5 per cent to 0.129-in. gauge and annealed to a 0.053-mm. grain size. In this condition, samples were cut and used in all of the experimental work reported in this paper. Time The first study was of crystal growth at a constant temperature over a moderate length of time. Material was cut from the stock coil at 0.129-in. size and rolled 75 per , cent hard to 0.032-in. gauge. From this piece small samples were cut M by 2 in., suitable for grain-size determina.tions. Twelve samples were placed in an electric furnace uniformly across the width, approximately an inch from the floor. A thermocouple was wired to the center sample, so that the approximate metal temperature could be followed. At various

Jan 1, 1944

By G. W. Binkley, R. E. Collins, G. K. Dumbauld

A mathematical analysis has shown that the primary factors affecting the deposition of cement in unfractured perforations during squeeze-cementing operations are: the properties of the cement slurry, the geometry of the perforations, and the filtration time. The validity of the analysis has been substantiated by laboratory investigations. The information presented in this paper makes possible the prediction of the rate of deposition of cement in and about unfractured perforations under given squeeze-cementing conditions, the proper filtration time to control the amount of deposition to any desired value, and the deposition properties needed in cement slurries to restrict to any desired degree the formation of nodes of cement .Solids inside the casing. INTRODUCTION The deposition of solids against a permeable medium by the process of filtration is an important property of a cement slurry. General recognition of the role of filtration in the use of cement in wells is evident in view of the fact that several patents on low-water-loss cements have been issued during the past few years. In the conventional, high-pressure squeeze-cementing technique, a large volume of cement slurry is usually displaced into the area surrounding the perforated interval after the formation has been fractured hydraulically.&apos; Near the end of the job, the pumping rate is slowed or stopped intermittently in an effort to obtain a high pressure in the wellbore. The way in which a high pressure is obtained is not understood thoroughly. but it is be- lieved to be caused by the deposition of a rigid mass of compacted cement particles either in the fractures of the formations or inside the casing opposite the perforated interval. In a method of squeeze-cementing introduced several years ago, a small amount of cement slurry is squeezed into the perforations at a low pressure to avoid fracturing the formation. The filling of the unfractured perforations with cement particles by the process of filtration is important to the success of this technique. Early in the development of this low-pressure squeeze-cementing technique, laboratory and field-size experiments showed that conventional, neat cement slurries were unsatisfactory if the tubing was extended into or through the perforated section of the casing. The extremely high filtration rate of neat cement slurries caused the deposition of a compacted mass of cement inside the casing and made it impossible to remove excess cement by reverse circulation and difficult to withdraw the tubing. Because the need for cements with a reduced filtration rate was obvioils and urgent, modified cements containing 12 per cent bentonite were used until research was completed on modified cements containing 25 per cent bentonite.< These modified cements were useful in the solution of the immediate problem, but the following questions remained unanswered: (I) what is the optimum filtration rate of cement slurries for this application, (2) how long should the squeeze pressure be applied. and (3) how great are the effects of squeeze pressure and well temperature on the rate of deposition? Furthermore, the relationship of the filtration properties of cement slurries to the dimensions of the perforations and the wellbore was unknown. In order to obtain information relative to these basic considerations, a systematic evaluation of all the factors involved in the deposition of Cement during low-pressure squeeze-cementing operations was initiated. Although the work was directed toward an evaluation of the factors influencing the deposition of Cement in the low-pressure squeeze-

The greatest mining center in the state of Utah is the incorporated town of Bingham about twenty-five miles southwest of Salt Lake City. The principal industry of this vicinity, prior to the early fall of 1863, was lumbering and the first saw-mill in the state was built near the mouth of Bingham Canyon. Early in the fall of that year. George B. Ogilvie discovered gold and shortly afterward the first mining district in the state was organized. Some writers place the discovery of gold in the canyon in the late fifties. If this be so, however, the matter was kept extremely quiet because no mining was engaged in until after Ogilvie&apos;s discovery. Bingham was a placer mining camp, producing about one million dollars&apos; worth of dust and nuggets from placers up and down the canyon and in Bear Gulch until early in the seventies, or about ten years after the discovery of gold, when a large body of argentiferous lead ore was discovered and soon after heavy shipments were made from a half dozen or more properties.

Jan 1, 1925

By H. R. Aldrich

THIS paper is not a treatise on the theory and practice of magnetic surveying. It merely presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern Wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretations of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies.

Jan 1, 1928

By Fred C. Bond

MOST investigators are aware of the present unsatisfactory state of information concerning the fundamentals of crushing and grinding. Considerable scattered empirical data exist, which are useful for predicting machine performance and give, acceptable accuracy when the installations and materials compared are quite similar. However, there is no widely accepted unifying principle or theory that can explain satisfactorily the actual energy input necessary in commercial installations, or can greatly extend the range of empirical comparisons. Two mutually contradictory theories have long existed&apos; in the literature, the Rittinger and Kick. They were derived from different viewpoints and logically lead to different results. The Rittinger theory is the older and more widely accepted. In its first form, as stated by P. R. Rittinger, it postulates that the useful work done in crushing and grinding is directly proportional to the new surface area produced and hence inversely proportional to the product diameter. In its second form it has been amplified and enlarged to include .the concept of surface energy; in this form it was precisely stated by A. M. Gaudin2 as follows: "The efficiency of a comminution operation is the ratio of the surface energy produced to the kinetic energy expended. According to the theory in its second form, measurements of the surface areas of the feed and product and determinations of the surface energy per unit of new surface area produced give the useful work accomplished. Computations using the best values of surface energy obtainable indicate that perhaps, 99 pct of the work input in crushing and grinding is wasted. However, no method of comminution has yet been devised which results in a reasonably high mechanical efficiency under this definition. Laboratory tests have been reported&apos; that support the theory in its first form by indicating that the new surface produced in. different grinds is proportional to the work input. However, most of these tests employ an unnatural feed consisting either of screened particles of one sieve size or a scalped feed which has had the fines removed. In these cases the proportion of work" done on. the finer product particles is greatly increased and distorted beyond that to be expected with a normal feed containing the natural fines. Tests on pure crystallized quartz are likely to be misleading since it does not follow the regular breakage pattern of most materials but is relatively harder to grind at the finer sizes, as will be shown later. This theory appears to be indefensible mathematically, since work is the product of force multiplied by distance, and the distance factor (particle deformation before breakage) is ignored. The Kick theory&apos; is based primarily upon the stress-strain diagram of cubes under compression, or the deformation factor. It states that the work required is proportional to the reduction in volume of the particles concerned. Where F represents the diameter of the feed particles and P is the diameter of the product particles, the reduction ratio Rr is F/P, and according to Kick the work input required for reduction to different sizes is proportional to log Rr/log 2.5 The Kick theory is mathematically more tenable than the Rittinger when cubes under compression are considered, but it obviously fails to assign a sufficient proportion of the total work in. reduction to the production of fine particles. According to the Rittinger theory as demonstrated by the theoretical breakage of cubes the new surface produced, and consequently the useful work input, is proportional to Rr-1.5 If a given reduction takes place in two or more stages, the overall reduction ratio is the product of the Rr values for each stage, and the sum of the work accomplished in all stages is proportional to the sum of each Rr-1 value multiplied by the relative surface area before each reduction stage. It appears that neither the Rittinger theory, which is concerned only with surface, nor the Kick theory, which is concerned only with volume, can be completely correct. Crushing and grinding are concerned both with surface and volume; the absorption of evenly applied stresses is proportional to the volume concerned, but breakage starts with a crack tip, usually on the surface, and the concentration of stresses on the surface motivates the formation of the crack tips. The evaluation of grinding results in terms of surface tons per kw-hr, based upon screen analysis, involves an assumption of the surface area of the subsieve product, which may cause important errors. The&apos;evaluation in terms of kw-hr per net ton of 200 mesh produced often leads to erroneous results when grinds of appreciably different fineness are compared, since the amount of -200 mesh material produced varies with the size distribution characteristics of the feed. This paper is concerned primarily with the development, proof, and application of a new Third Theory, which should eliminate the objections to the two old theories and serve as a practical unifying principle for comminution in all size ranges. Both of the old theories have been remarkably barren of practical results when applied to actual crushing and grinding installations. The need for a new satisfactory theory is more acute than those not directly concerned, with crushing and grinding calculations can realize. In developing a new theory it is first necessary to re-examine critically the assumptions underlying

Jan 1, 1952

By C. Dalton, H. L. McGill

The purpose of this study was to develop a method for predicting the time delay created by metering a fluid through an annular restriction with translational motion of the boundaries. This time delay is utilized to control the opening of valves in various down-hole oilfield tools and forms the basis for the "hydraulic jar". The hydraulic jar is used to give upward impact forces to tubing or other tools that become lodged down-hole. The design of these jars has primarily been by trial and error; varying the clearances, fluid viscosities and dimensions of the jar until a satisfactory time delay was achieved. Obviously, a better understanding of the fluid flow characteristics is required to produce designs that are satisfactory and to eliminate the trial-and-error approach. Previous studies of flow in annular spaces were based on constant length of the annular restriction. Any motion of the boundaries of the annular space was confined to a rotational motion, like that encountered in journal bearing design. Consideration of the effect of translational motion of one boundary with respect to the other was necessary in applying this previous work to a time delay device. A prediction method was developed that takes into account this relative translational motion. Equations were developed to predict the relative velocity, the flow rate, and the time delay in a concentric annular space. The effect of eccentricity also was included. Experimental data were obtained and closely correlated with the prediction method. This correlation is presented graphically in terms of predicted and actual relative velocities for various annular clearances and pressure drops. This extension provides design equations which predict the performance of the hydraulic jar, thereby eliminating trial-and-error solutions and reducing the development time required for satisfactory designs. INTRODUCTION The design of down-hole oilfield tools which use hydraulic delay systems based on flow through annular orifices with relative motion of the boundaries is usually a trial-and-error process. The annular clearances, fluid viscosities and dimensions of the mechanisms were varied until satisfactory delay times were obtained. The development of these tools has been expensive, and a better understanding of the characteristics of annular flow with relative motion of the boundaries could result in superior and less expensive designs. The purpose of this investigation was to provide a method of predicting the performance of down-hole tools which use annular flow and, in particular, the performance of a down-hole tool known as the "hydraulic jar". The hydraulic jar is used to free pipe, packers and other tools that become lodged down-hole. The jar, located in the tubing string between the surface and the object which is stuck, releases the object though the repeated application of upward impact blows. The jar is basically a slip joint that is restrained in a collapsed condition until the desired tubing tension has been developed. The slip joint is then released and accelerates rapidly until it shoulders, delivering an impact blow or jar to the object. The delay obtained by metering the fluid through the annulus formed by the jar valve and housing provides the time delay necessary to stretch and apply tension to the tubing or pipe. Fig. 1A gives a schematic diagram of the hydraulic jar and brief details of its operation. The metering of the hydraulic jar begins when the tension force being applied to the jar by the pipe creates a pressure differential across the valve that is approximately equal to the force divided by the displacement area of the valve. This pressure differential induces flow through the annular restriction formed between the valve and housing. The valve moves with respect to the housing as the

Jan 1, 1969

By Henry S. Munroe

The earliest accounts we have of Japan represent the country as having great mineral wealth, especially of precious and useful metals. Marco Polo, the Venetian traveller, in the thirteenth century, writes of "Zipangu:" " They have gold in greatest abundance, its sources being inexhaustible. The king does not allow of its being exported. To this circumstance we are to attribute the extraordinary richness of the sovereign&apos;s palace. The entire roof is covered with a plating of gold.. .. The ceilings of the halls are of the same precious metal; many of the apartments have tables of pure gold of considerable thickness, and the windows also have golden ornaments." Marco Polo also gives an account of an unsuccessful Tartar expedition against Japan, prompted by the supposed great wealth of the country. Columbus also, as well as many other explorers, were attracted and encouraged by these prevalent reports of the wealth of the islands of Zipangu. Kaempfer, writing in 1727, speaks of the great mineral wealth of Japan, and especially of the abundance of gold, which, he says, is found in many provinces. The Portuguese and Dutch, while they had trading-posts in Japan, furnished tangible evidence of the truth of the early reports. Between 1550 and 1639 the Portuguese merchants sent home from Japan nearly three hundred million dollars&apos; worth of bullion, most of which was gold. As the relative value of equal weights of gold and silver was then six to one, while in Europe, at the same time, it was nearly twelve to one, the exchange of silver bullion for gold was by no means an unimportant part of their Business. After the Portuguese, the Dutch continued the exportation of bullion, and the exchange of silver for gold, though with less profit, as the relative value of gold increased with the demand. Between 1649 and 1671 the Dutch traders sent home over two hundred million dollars in bullion, of which, however, nearly two-thirds was silver. In 1671 the Japanese government, alarmed at the rapid rate at which the precious metals were leaving the country, issued an edict forbidding the exportation of gold or silver, under heavy penalties, which had the immediate effect of stopping this trade. Besides bullion, copper formed at this time a most important article of export. According to Dr. Geerts,* who has examined the old