Search Documents

By A. R. Jr. Amos

LOG washers have been used for many years in the washing of clay iron ores, phosphate rock and manganese ores, but not until the past 15 years have they been employed to any extent in the preparation of aggregate materials and fluxing stone. For a machine of such importance where tenacious clay or soft rock must be eliminated, there are few data generally available. The purpose of this paper is to set forth the results obtained from several operations, together with a few suggestions for planning a specific installation. Where the material to be washed out consists of loose surface soil, silt, or small amounts of quickly soluble clay, there is little competition with other forms of washers, because greater power and maintenance are required for the operation of log washers, but where the foreign matter is a stiff clay, such as occurs with high-calcium limestones and in marginal gravel deposits, the ability of other kinds of washers to eliminate com-pletely the hard clay balls is at least uncertain. Then the log washer comes into its own field, for with the breaking and churning action of the logs it will clean out the toughest clay. Even with material from the hydraulic dredge, if it contains tough clay, the log washer is desirable unless the gravel is subjected to a costly soaking and rehandling process. Recently there has been a considerable development in other types of machines to accomplish these results but it is not within the scope of this paper to make comparisons between competitive types, but to present the best obtainable data on log washers only. From the primitive design that gave it its name, a long log hewn from a tree, with paddles forged to shape from strap iron and attached by lag screws, the log washer has gradually been developed to the present all-steel type. As now manufactured, the log washer consists essentially of two built-up logs on which are mounted a series of paddles, carried by shafts fitted at the ends of the logs on bearings fastened outside the enclosing steel box, or trough, which is set at an angle of about 5° to 10° and into which the material is fed. Stuffing boxes at the places where the shafts pass through the box at the lower end are equipped with water-

Jan 1, 1936

By G. Sachs, S. I. Liu

Introduction In a previous investigation on the effects of repeated strains of large magnitude on the aluminum alloy 24 ST, it was found that the reduction in ductility by straining in tension was partially restored by a subsequent compression.&apos; As illustrated by the dashed line in Fig I,$ the ductility (e~) retained after prestraining in tension by a certain amount (el) and measured in a subsequent tension test is represented by a straight line sloping down under 4s°. If a compression of the same magnitude as the first tension is inserted (€2 = — €1) between prestraining and final testing in tension, such a "balanced" tension-compression cycle yields a ductility considerably higher than that present after prestraining in tension only. The results of these tests can be correlated with those of an investigation on the effects of prestraining in compression.~ As also shown in Fig I, the ductility in subsequent tensile tests decreased with com- pression, at a rate considerably slower than that after prestraining in tension. The above discussed testing conditions can be considered as special cases of a general straining cycle, consisting of first, straining in tension by an amount el, subsequently straining in compression by an amount e2, and finally determining the retained &apos;ductility, e,, in a tensile test. Prestraining in tension is then represented by el > o and e2 = o. Prestraining in compression is given by e~ = o and e~ < o. Balanced cyclic straining is defined by the condition el > o and cz = — 61. In order to obtain further information on the effects of straining cycles consisting of tension and subsequent compression, further tests were made, varying both the tension strain, el, and the compression strain, e2, within extreme limits; el varied between 0.06 and 0.28 and e2 between — 0.008 and —0.h approximately. Apparently, such tests have not been previously performed. They revealed phenomena which have not been recognized to date, The results of the investigation are herewith reported, without attempting to correlate them with internal processes within the metal structure. However, in order to assist in an analysis of this type, the results have been represented in various manners. In addition, further test data on the effects of prestraining by compression were provided by using specimens of various contours (notched specimens) in the sub-

Jan 1, 1949

By Thos Gibson

THE object of taxation is the raising of a revenue. Unless a tax accomplishes this, it is a failure. The right to take for public purposes a part of the moneys obtained from the carrying on of private enterprises is an attribute possessed only by a lawful government, and may indeed he called the supreme attribute of government. In free, democratic communities this power must of necessity rest upon the consent of the governed. Power implies obligation, hence it is obviously the duty of a government, in framing a system of taxation, to provide one which, while effective in producing a revenue, is also just and impartial. It will be conceded that mines and mining property ought to bear a fair share of the public expenditure. The question is, upon what basis taxation should proceed. Two separate taxing principles are usually contended for: Taxation should be proportionate to the benefits received by the person or property taxed; taxation should be based on ability to pay. A third is sometimes added, taxation should have reference to the extent and value of the natural resources enjoyed. As applied to mining taxation, it is pointed out by those who support the first mentioned basis that, mines being usually situated in rocky and hence sparsely peopled regions, mining companies are frequently obliged to construct roads, railways, telegraph and telephone lines, schools, water and sewerage systems, and many other amenities and conveniences of civilization, the cost of which in regions better suited for agriculture and consequently more thickly populated, has either been defrayed locally, or can be spread over a sufficiently large taxable group of people to materially lighten the financial burden on the mine. The mining com¬pany, it is argued, having made these outlays, should receive credit for, them and be relieved of taxation to a corresponding extent. There may be some force in this contention, but the situation is capable of relief without attempting to place taxation upon so unworkable a basis as the value of benefits received. Who is to be the judge of these benefits, and how are they to be valued? The very existence of a mining company and its ability to carry on business in peace and security, depend on the prevalence of law and order, which is a result of good government. The state provides protection against violence, and courts of law for

Jan 4, 1919

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany&apos;s basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By G. Derge, Lo Ching Chang

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By R. W. Harper, M. C. Fuerstenau, J. D. Miller

Data were obtained with hematite with octyl hydroxamate and oleate as collectors to determine the mechanism of collector adsorption and also to establish the roles that conditioning time and temperature assume in this system. The presence of hydroxy complexes of iron are apparently necessary for chemisorption of collector to occur, and it appears as if extended conditioning times and elevated temperature promote greater dissolution of the mineral and hence greater concentrations of hydroxy complexes. Data were also collected with two natural hematitic ores. With one ore that was ground to 70% - 15u, an addition of 0.4 lb per ton hydrox-amate resulted in a final concentrate recovery of 86% at a grade of 64% iron. Satisfactory concentrate grade could not be obtained with fatty acid under these conditions. The effect of conditioning time prior to the addition of collector was also examined with another ore. When the ore was conditioned for 3 min, 19% of the iron was recovered in the concentrate at a grade of 67% Fe. With a conditioning time of 7 min, 73% of the iron reported to the concentrate at a grade of 62% Fe. These products were obtained with an addition of 0.2 lb per ton hydroxamate. This ore also responded well to flotation with fatty acid. The use of potassium octyl hydroxamate as a collector for iron oxide has been the subject of an earlier study.1 From this initial study, it was suspected that hydrolysis of surface ferric iron was involved in collector adsorption. More recent work in other systems has shown that slight mineral dissolution, followed by hydrolysis of cations common to the mineral lattice, is apparently necessary, and that adsorption of these hydroxy com- plexes probably occurs prior to the adsorption of collector. In view of these facts, work has been continued on the hydroxamate-hematite and oleate-hematite systems to gain better insight into the mechanisms of collector adsorption on iron oxide. Microflotation experiments in conjunction with infrared analysis were used in this regard. In addition it was felt necessary to establish more clearly the responses that can be obtained from natural ores when hydroxamate is used as collector as compared to those obtained when fatty acid is used. Experimental Materials and Techniques Pure potassium oleate, potassium octyl hydroxamate, synthesized from hydroxylamine hydrochloride and methyl octanoate, and a distilled Tall Oil were employed as collectors. Conductivity water was used in the

Jan 1, 1971

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By D. J. McAdam, G. W. Geil, R. W. Mebs

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,&apos;-&apos;&apos; the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals &apos;&apos;should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture&apos; In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By R. W. Mebs, G. W. Geil, D. J. McAdam

As shown in previous papers by the authorsg-17t the resistance of a metal to fracture, like its resistance to plastic deformation, is a function of all three principal stresses. A technical cohesion limit is the technically determined resistance to fracture under a specific stress system. The technical cohesive strength thus comprises an infinite number of technical cohesion limits corresponding to the infinite number Of possible com-binations of the principal stresses. The technical cohesive strength, therefore, may be represented by a surface in a diagram with the three principal stresses as coordinates. As shown in previous papers,&apos;-&apos;&apos; the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. More- over, the influence of each of these factors on the technical cohesion limit has been shown to be qualitatively similar to the three of the same factor on the flow stress.9-18 Advance of knowledge about the conditions determining fracture of metals has been retarded by the reluctance of some investigators to abandon preconceived ideas about how metals &apos;&apos;should,, behave. The incorrect idea is still prevalent that the conditions determining resistance to fracture are very different from those determining the flow stress. Attempts are still being made to express resistance to fracture in terms of a single parameter, such as a limiting value of the greatest principal stress, the maximum shearing stress, or the volume stress (one-third the algebraic sum of the three principal stresses). In these attempts, a sharp distinction is sometimes made between a ductile or ,plasticdeformation, fracture,, and a "brittle frat-ture.H In making this distinction, however, the meaning attached to the term "brittle fracture" sometimes is not made clear. The term could mean fracture after very little plastic deformation or it could be used to designate the type of fracture. An ordinary fracture of a ductile metal at room temperature starts as a cleavage, generally transverse to the direction of the greatest principal stress, but eventually changes to a shearing fracture&apos; In some conditions, however, the metal fractures entirely by cleavage, with no evidence of plastic deformation during the fracture; the surface of such a fracture may have a

Jan 1, 1948

By Gerald Edmunds

THE liquidus line on the phase diagram for temperature versus composition of a binary alloy system, representing the boundary between the homogeneous melt and the heterogeneous melt plus solid, besides showing the minimum casting temperature, is useful in determining eutectic compositions and the presence of phase changes such as peritectic transformations and intermetallic compound formation. The liquidus often is determined by the cooling curves of thermal analysis, but supercooling frequently occurs, so that the temperature values are low. An alternative method, the one employed here, consists of determining the com- position of samples of the melts from heterogeneous alloys that are at equilibrium. With meticulous attention to fundamentals, this method is capable of yielding values limited in precision only by the temperature control and measurement and analyses. APPARATUS By starting, on the one hand, with a supersaturated solution and allowing the excess solute to precipitate, and on the other hand with an undersaturated solution and allowing more of the solute to be dissolved, both processes being carried out at the same temperature, equilibrium may be said to have been approached from both directions; that is, from above and from below. If the analyses show the solutions to contain the same fraction of solute when equilibrium has been approached from above and from below, one is assured that equilibrium has been reached in both determinations. In order to carry out such determinations, it is necessary to have equipment for obtaining and maintaining the proper temperatures; for holding the melt, measuring its temperature, and stirring, sampling and analyzing it. The present work required temperatures from 420° to 900°C. The equipment consisted of: A furnace, which was a vertical alundum tube, 1 ¾ in. diameter inside and 18 in. long, wound with Nichrome resistance wire, surrounded by a 3-in. i.d. alundum tube wound for 5 in. of length near each end, for compensation of end losses. This muffle was contained in an iron shell with Transite end plates, the intervening space being packed with Sil-O-Cel. The outside dimensions of the furnace were 12 in. in diameter by 18 ½ in. in height. Heating current was supplied by three independent variable-voltage transformers (Variac), one connected to each end compensator winding and manually controlled, and one connected to the main winding through a series resistance of 5 ohms. This resistance was short-circuited for

Jan 1, 1944

By Jacques B. Wertz

Detailed structural studies in southeast Arizona have successively revealed (1) the local attitudes of individual fractures (with lateral and/or vertical displacements), (2) the patterns exhibited by groups of fractures, and (3) the trends and directions shown by fracture groups or zones on a regional scale. The results of the studies have been twofold: First, domes were locally determined from these fracture arrangements, even where other criteria failed; and, second, fundamental breaks brought out the breadth of the Texas lineament in southeast Arizona as well as major northwest- and northeast-trending fracture zones. Coincidence of one or several domes with the major intersections of fundamental breaks can be centers of important mineralization, as in the instances of Bisbee, Ajo and Morenci. THE OVER-ALL STRUCTURE OF ARIZONA A northwest-southeast trending anticlinorium has been suggested as the structural setting of Arizona. Starting in Triassic and culminating in late Cretaceous times, this deformation resulted from stresses of considerable magnitude with varying ratios of com pres sional and uplifting forces. However, the series of parallel flexures could just as well have been caused by isostatic movements involving dilation under tension with only incidental compression, as later emphasized by dike filling and block faulting (Fig. 1). The anticlinorial deformation, which is also suggested by the fact that the Pre-cambrian rocks to the southwest are all concealed by sediments, could be somewhat reminiscent of the conditions that affected the classical swarm of parallel dikes of wager.&apos; ANALYSlS OF DATA As a first step in this analysis, all structural information obtained on such features as fractures and their relative displacements, faults, dikes, anticlines, synclines, and Precambrian and Laramide-Tertiary intrusives were plotted on maps along with structural trends inferred from aerial photographic mosaics. Next, the faults in southwest Arizona were classified according to time of occurrence and relative importance. The fault assemblages were then examined as to geometric or spatial arrangement and correlated with the occurrences of domes and existing Finally, the conjunction of fracture intersections and domes was analyzed and compared with locations of known ore deposits. Differentiation of Faults According to Time and Relative Importance: The faults encountered were grouped as follows: (1) Basin and Range faults, latest in time; (2) secondary faults; (3) primary faults; and (4) lineaments, earliest in time by inference. BASIN AND RANGE FAULTS- Generally concealed by alluvium, the Basin and Range faults are normal

Jan 1, 1969

By Donald L. Katz

THE Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July 1, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produces 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand&apos; indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplification and generalizations are necessary to give the over-all picture in so short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, r, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City. Wilcox Secondary Recovery Association on Sept. 5;.1940. Some information is taken from a report to the Association by C. V. Sidwell on March 1, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." HISTORY OF WILCOX ZONE The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. 12.1 .4 and areal map of Fig. 2. The sand is of Ordivician age and is composed of well assorted, rounded&apos; sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 was dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1937 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1941

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

James W. Malcolmson died suddenly on Dec. 26, 1917, at Kansas City, Mo., where he had made his home for the past ten years. He was born at Dover, Kent, England, on Oct. 6, 1866. He graduated from the Royal School of Science, London, England, in 1889, and almost immediately after graduation came to Mexico, accepting a position with the Michoacan Railway and Mining Co., as mining and mechanical engineer. His work in the mining profession was carried on principally in Msxiac and the United States. • In 1888, he married Katherine Haden Krause, of Woolwich, Kent, England, and leaves, besides his wife, five sons and one daughter. During Mr. Malcolmson&apos;s long and successful career as a mining engineer, he was connected with the following companies: from 1889 to 1893, with the Michoacan Railway and Mining Co., as mining and mechanical engineer; from 1893 to 1898, in various capacities with the Kansas City Smelting & Refining Co.; after the consolidation of the Kansas City Smelting & Refining Co. with the American Smelting & Refining Co., he remained as manager of the mining department in Mexico of the American Smelting & Refining Co. until 1902. In 1902, he located in El Paso, and took up the practice of his profession as a consulting engineer. While there, he was consulting engineer for the famous and rich Pedrazzini mines at Chispas, in the State of Sonora. He was instrumental in organizing the La Republics mine in Chihuahua, and for a time acted as consulting engineer for the property. He remained in El Paso until 1907 and then moved to Kansas City and became associated with the United States & Mexican Trust Co., as consulting engineer. In 1909, he became connected with The Lucky Tiger Combination Gold Mining Co., as its consulting engineer, and continued in this connection and in the general practice of his profession as consulting engineer until his death.. His general policy in connection with the Lucky Tiger company was always a progressive one and the success of the enterprise can be largely attributed to him and his good judgment. Mr. Malcolmson contributed several articles to the Institute at different times, one of them being on the ore deposits of the Sierra Mojada Mining District, in 1901. Much of his work was in Mexico, and during his long residence in that country he acquired a very thorough knowledge of the Mexican people and their customs. During the revolution, from 1910 to 1916, this knowledge was of great value in connection with his work for the Lucky Tiger company, and often assisted greatly in keeping the property going. Mr. Malcolmson was one of the very widely known men in his profession; he was everywhere held in the very highest regard, and his position among men in the mining profession was an enviable and honorable one. At the time of his death, besides being consulting engineer for the Lucky Tiger company, he was interested in mines in the Miami zinc fields and was acting as consulting engineer for two of the operating properties there. He invested to quite an extent in real estate when he moved to Kansas City in 1907 and his investments in this line proved successful.

Jan 1, 1920

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By Oliver Bowles

AMONG mining men as well as in the popular mind the conviction has held sway that mining is pre-eminently a western industry. True it is that gold, silver, copper and other metals have made the States of California, Colorado, Montana, Utah. Nevada and Arizona famous. The prominence attained by these States as mineral producers is, however, not measured alone by the money value of the products of their mines. While the metals are without doubt indispensable in industry, the glamour of the precious metals, and the lure of copper, lead and zinc have given to their ore deposits a sentimental interest that often quite out-weighs their commercial importance. Today a great group of more commonplace minerals are finding a place in commerce and industry rivaling that of the metals, but there is little sentiment attached to them, and,. therefore, they attain relatively little publicity. This is the great group of the non-metallic minerals, exclusive of fuels and oils, including stone, sand and gravel, cement, lime, gypsum, asbestos, mica, phos-phate rock and many others. Almost unnoticed they have grown in production to almost unbelievable pro-portions. The estimated value of metal production for 1925 is given as $1,380,000,000, of the non-metals (ex-cluding fuels) $1,294,000,000. The non-metallic industries are not new, many of them date back almost to pre-historic times; but, as the greatest of them (on a tonnage basis) provides raw materials for the construction industries, it required the activities of the present age of construction to bring about their enormous development. Many of them enter manufacturing as well as con-struction. Non-metallic minerals constitute the back-bone of our great chemical industries. While construction and manufacture reach to all parts of the country their widest development has been in the great industrial centers of the eastern Seaboard and the middle West. Consequently the raw materials of mineral origin required for these great industries have attained a remarkable growth in the eastern half of the- United States. In compiling figures of mineral production for 1924, for which more complete data are available than for later years, the surprising fact is brought to light that the non-metallic mineral produc-tion alone of some of the eastern and middle-western States exceeds by a substantial margin the total min-eral production of some of the western States that have been classed as essentially mining States. Thus the non-metallic mineral production, exclusive of coal and petroleum, of the State of Ohio, was approximately $150,000,000; of Pennsylvania $175,000,000; and of New York $107,000,000. For the same year, 1924, the total mineral production of Utah was $84,357,000; of Montana $70,632,000; of Colorado $61,488,000; and of Nevada only $26,226,000. Even Minnesota, with its enormous iron ore production, reached only $107,845,-000, or a sum about equivalent to the non-metallic min-eral production of the State of New York.

Jan 8, 1927

By John T. Galey

Production of crude oil for 1940 in southwestern Pennsylvania was off nearly 70,000 bbl., largely as a result of the great number oi abandonments, together with the lack of extension of the Washington and Green County pools. Oil wells completed numbered 51, which is 26 more than last year, but the total initial production of 259 bbl. is only 18 bbl. greater than in 1939. There was an increase of 72 over last year for a total of 209f gas wells. However, 68 7 dry holes were drilled, which is 40 more than a year ago. Thus, 328f wells were drilled during the year, and rigs are erected or drilling is progressing on 59 t more. Shallow Development Oil.—Butler County led in number of oil wells completed, with a total of 27 for an initial production of only 69 bbl. Washington County, with 12 new oil wells, one of which made 40 bbl. from the Fifth sand in S. Franklin township, has 95 bbl., while in Allegheny County 9 wells gave an initial of 86 bbl. for the highest Per well average in the area. This initial was given a considerable boost by one 35-bbl and another 2;-bbl. well in West Deer township, where the Fourth sand produced at 1840 feet. Greene County had only one oil well completed during 1940, and Washington County had 12. The subnormal totals for these counties may be explained by the higher cost of completions and the declining price of crude. The first price change in crude during the year occurred on May 22, when a 25 cut was made. A second 25 cut was made July 12, and was followed by a 156 cut on .Aug. 28. This price held until Nov. 12, when there was a restoration of 156. On Dec. 17 a second 156 increase was put into effect, bringing the price to $I.So per barrel. Gas The large increase in the number of gas wells completed may be attributed to three factors; namely, the recently discovered production possibilities of moderately deep, hitherto little tested horizons, together with increased demand and price. The latter has been made possible by a recent decision of the court, which ruled restraining the public service Commision&apos;s prohibition of a raise in the minimum monthly charge to small consumers by one of the major gas companies. A portion of the revenue derived in this manner is being passed along to the producer in the form of higher prices in the field. This higher field rate will remain in effect until a new ruling is made, when it will be reduced in proportion to the reduction of the monthly minimum charge. In an effort to extend the chambers Dam Fifth sand oil pool southwest from Amwell township, Washington County, several wells have been drilled. One of these, in Morris township, washington County, had an initial of 3.2 million cu. ft. open flow from the Big Injun sand. This indicates an entirely new productive area for the latter horizon. Allegheny County had one spectacular well in South Fayette township-—at a depth of about 2500 ft. a 4-million-CU. ft.

Jan 1, 1941

By Alec M. Crowell, J. W. Sanders

While the production of crude oil and condensate in South Arkansas increased only 1.7 per cent over the 1940 figure, complete utilization of gas produced with the oil and condensate, and heretofore wasted, was beginning to be evidenced. There were 26,229,264 bbl. of oil and condensate produced in South Arkansas during 1941, as against 25,790,380 bbl. for the year 1940. (Fig. I.) Since 1936, deep producing sands have been discovered in 18 fields and during that period only 40 per cent of the total state production has come from Upper Cretaceous formations while 60 per cent came from the Lower Cretaceous and Jurassic formations. The gas produced with crude oil and condensate from the latter formation contains large quantities of hydrogen sulphide, the maximum being 6900 grains per 100 cu. ft. in the Patton pool of Lafayette County. Gas Utilization During the latter part of 1940 and the early part of 1941, pilot plants were placed in operation to determine whether the hydrogen sulphide and deleterious material in South Arkansas gases could be removed economically. The Federal Government desired to build a large aluminum plant in the Ouachita Valley and was seeking cheap fuel for the generation of electricity. The fact that the gases were produced with appreciable quantities of crude oil and condensate made it available at a very low price, since the state&apos;s conservation law prohibits the flaring of any gas. As a result of these experiments the first large-scale unit for the processing of gases containing hydrogen sulphide was placed in operation on Sept. I, 1941. The plant is in the Magnolia oil field, Columbia County. It processes residue gas from the Shell Oil Company&apos;s gasoline plant in that field and also raw gas from the Village field, 6 miles east of the Magnolia field. The gas entering the desulphuri-zation unit is laden with approximately 1400 grains of hydrogen sulphide per 100 cu. ft. and is stripped to a content of 4 grains per 100 cu. ft. The capacity of the plant is 15 million cu. ft. of gas treated daily under a pressure of 160 lb. per sq. in. The cost of treatment, exclusive of depreciation, is appreciably less than I per 1000 cubic feet. Two other plants of much greater capacity have been announced and priorities have been granted, which should bring the total amount of gas treated to 150 million cu. ft. daily. The gas to be treated will have a maximum hydrogen sulphide content of 4500 grains per 100 cu. ft. and will be processed under a pressure of 600 lb. per sq. in. These developments are something entirely new in field practice for the industry. The fact that this heretofore wasted gas is available at very low cost has led to the location of some eight war industries within the state, in addition to the alu-minum plant. Recovery OF Sulphur The Susearch Corporation and the Southern Acid and Sulphur Co. placed in operation during 1941 pilot plants to de-

Jan 1, 1942

By E. L. Kinsella, F. S. White

Solids fluidization utilized in two ways for the commercial production of lime is described. Crushed —6 mesh limestone is dried and dedusted in a single bed reactor, then calcined in a 5-stage reactor. Construction, operation, and results obtained with both processes are given. THE solids fluidization process brought out by the Standard Oil Development Co. in the early forties for catalytic cracking of petroleum enabled rapid transfer of large quantities of heat from gases to solids under closely controlled temperature conditions. As the technique developed, it was natural that applications for the process outside the petroleum industry would be sought. The calcination of limestone to quicklime requires the transfer of a large quantity of heat at high and closely controlled temperatures. For these reasons, this possible application was one of the first to be investigated. Laboratory work conducted by the Dorr Co. indicated that lime produced by solids fluidization would be of exceptional quality. Calculation of theoretical heat balances showed that savings in fuel could be expected. Accordingly, a pilot plant of 10 tons per day capacity was erected by the New England Lime Co. at Adams, Mass., to substantiate the process. Operation of the pilot plant, previously described,&apos; showed that excellent lime could be produced with a saving in fuel. The work also indicated the necessity of preparing feed to remove the finer fractions if dust losses were to be held to a tolerable level. A single-stage fluidized solids drier-stripper was developed to accomplish this sizing.&apos; Subsequently a commercial lime reactor was erected at Adams, beginning operation in June 1949, followed by air sizer facilities completed in November 1951. This paper will describe these two applications of solids fluidization. The raw material for preparation of lime by the fluidizing process is a high calcium crystalline lime- stone having the approximate chemical composition shown in Table I. The stone is first prepared by crushing and grinding in conventional equipment to pass a 6-mesh sieve. After crushing, the material is sent to the FluoDry unit for drying and dedusting. Fluidized Drying and Sizing As shown in Fig. 1, the FluoDry unit consists of a -in. cylindrical steel shell, 9-ft ID by 22-ft 6-in. overall height. Attached horizontallv at the bottom is a 6-ft diam combustion chamber, approximately 7 ft 6 in. long. A refractory constriction dome, consisting of first-quality fire brick shapes, partitions the inside into two sections. The lower section is called the windbox and the upper the bed compartment. The vertical wall of the shell is lined with 6-in. first-quality rotary kiln blocks. In the bottom of the windbox a hoppered section is formed with castable refractory to permit the windbox to be readily cleaned via a 6-in. screw conveyor. The combustion chamber is similarly lined with refractory shapes. On the 6-in. diam section, 4 in. of insulating brick, HW-26, are used. The inner combustion chamber is lined with 4-in. Korundal brick to withstand the high flame temperatures encountered. An 8-in. steel feed pipe, entering vertically through the top and fitted with an air-operated cone valve,

Jan 1, 1953

By John M. Kelly

New Mexico produced 31,913,816 bbl. of oil in 1942, the lowest annual production since 1936, and dropped one place to rank eighth among oil-producing states. This production decreased 7,838,052 bbl., or 19.71 per cent, from the 1941 figure is the result of transportation difficulties caused by the dislocation of tanker sailings to east coast ports. The average per-well allowable in New Mexico on Jan. I, 1942, was 43 bbl. and at the end of the year was 38 bbl. Allocations as set by the New Mexico Oil Conservation Commission followed the recommendations of the Petroleum Administrator for War. After setting the daily outlet, however, the average daily pipe-line runs were 87,545 bbl.—11.06 per cent short of these allocations. Production for Lea County was 26,812,949 bbl., Eddy County 4,624,578 bbl., northwestern New Mexico 473,609 bbl., Chaves County 2,680 barrels. Drilling activity for New Mexico in 1942 was approximately 84 per cent of that in 1941 with 339 completions. Of these completions 254 were oil wells, II gas wells, and 74 dry holes. Proven fields accounted for 55 of the dry holes and 19 were wildcats. Three new oil fields and one new gas field were discovered as the result of wildcat drilling. Extensions were made to one oil field and one gas field. By the close of the year, the New Mexico Oil Conservation Commission had designated 59 areas as proven for oil and/or gas. Southeastern New Mexico Lea County Monument was again the largest producing field in the state, with 5,729,336 bbl.; Eunice was next, with 5,217,965; Vacuum produced 3,295,624 and Hobbs 2,973,488. The Hobbs field has the largest accumulated production, which at the close of 1942 totaled 100,381,417 bbl. The 100-million-barrel mark for Hobbs focused attention on the fact that this is the first field in the state to attain this figure, and also that, as Hobbs has been under continuous proration since July 1930, or approximately the entire life of the field, this 100-million-barrel recovery was obtained with 86 per cent of the wells in the pool still flowing and having a drop in bottom-hole pressure of only 3.5 Ib. per million barrels recovered. Hobbs stands out as perhaps the best regulated major oil field in the world. Two new oil fields were discovered in Lca County, the most inlportant being the area designated as East Lusk, consisting of the south 4 tiers of Sections in T. 19 S., R. 32 E. The discovery well was drilled in the SW. SW. 1/4 of sec. 21, T. 19 S., R. 32 E., by Culbertson and Irwin, Inc., and others. It was completed at a total depth of 2751 ft. in the Seven Rivers formation of Permian age. The initial potential of the well was 237 bbl. per day on pump. The oil produced has a gravity of 24.10 A.P.I., with sulphur content of 0.9 per cent. This oil has an asphaltic base and because

Jan 1, 1943