Search Documents

By E. V. Potter, H. C. Lukens

The volume of hydrogen released from electrolytic manganese at various temperatures and pressures was determined in a previous investigation1 as part of a study to determine the most practical procedure for removing the hydrogen from electrolytic manganese metal. No attempt was made to determine the absolute volume of gas in the metal at any temperature and pressure; the volume of gas released showed only the variation in solubility with temperature and pressure. The results were very similar to those obtained by Sieverts and Moritz.² Both sets of data show a minimum solubility between 500' and 700°C., but they differ in certain respects; on cooling from 500°C., our results showed an increase in solubility of about 7 C.C. as compared with an increase of 34 C.C. per 100 grams shown by Sieverts. Furthermore, the transition temperatures, as indicated by sharp breaks in the solubility curves, did not agree well with Sieverts' data. This information was of secondary importance in the earlier investigations, and the solubility at low temperatures and the transition temperatures were subject to considerable error. Therefore, a subsequent investigation, reported in this paper, was made to measure the absolute solubility at temperatures from room temperature through the melting point and make more accurate observations of the transition temperatures. Apparatus and Method The apparatus and method were essentially the same as those described in the previous work,' as shown in Fig. I. At high temperatures, the small tube containing the thermocouple in the sample container A frequently broke off, so for some of this work the thermocouple was placed outside the sample container and protected by a quartz tube of about the same wall thickness as the sample container. No significant difference was found in the transition temperatures obtained in the two ways. The automatic temperature controller was used in these tests in the regions where there was little change in solubility with temperature. In the neighborhood of the transition points a continuously variable autotransformer was used instead of the automatic controller, and the power input to the furnace was adjusted so that the temperature increased or decreased at a very slow, uniform rate through the transition range. This procedure was followed because the temperature oscillations produced by the controller were too great compared with the transition range, and the transi- . tion points determined under such conditions were less accurate. Absolute Solubility Procedure ad Results The absolute solubility of hydrogen in manganese could be determined most

Jan 1, 1947

By Robert P. Burrows

In preparing this paper the object has been to set forth facts relating to illumination problems, which, judging from the results realized in the iron and steel and other industries somewhat similar to mining, will tend toward furthering safety, production, and contentment of employees, as well as economy of operation in mines. By applying the principles of illumination with the assistance of modern appliances, the full benefits in efficiency may be derived from improvements already made in other details of mine operation. The lighting of a typical coal mine may be*divided into four distinct parts: 1, The lighting of the buildings about the top; 2, the lighting of the working faces; 3, general illumination at the bottom; and 4, special applications of lighting. The lighting of buildings about the top may be treated in the same manner as that of any other industrial plant, for we have a boiler room, an engine and generator room, a forge, a machine shop, and a hoist room. These can be well and efficiently lighted by the use of 100-watt tungsten-filament multiple lamps with proper reflectors so spaced and suspended that a power consumption of from ¼ watt per square foot in the boiler room to 1 watt per square foot in the machine shop is obtained. The methods that apply to this kind of lighting have been ably treated by a number of authors,' and for this reason a detailed discussion is unnecessary. The lighting of the working faces is usually done by means of portable lamps, of which there are four types in use: The oil torch, the acetylene Iamp, and the oil and the electric safety lamps. The different types have been fully described in numerous papers and articles and will not be covered here, although a few figures on the cost of operation will no doubt be

Jan 1, 1916

By D. R. Spink

In the preparation of zirconium and hafnium metals, there are many indications that impurity levels control the physical and chemical properties of the metal. The purpose of this work was to develop methods of producing pure raw materials that could be reduced to highly pure metals. Early work by the Carbomcndum Metals Co. and others indicated that certain fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. We have developed workable fused salts along with a continuous and higly efficient scrubber design which can be used to produce very pure zirconium tetrachloride. Metal made from the purified tetrachloride has been shown to approach crystal bar metal in purity. Scrubber designs are discussed with recommended materials of construction. VARIOUS methods have been used to purify zirconium (and hafnium) tetrachloride. Most of these methods involve thermal degassing initially (the removal of more volatile compounds at temperatures below that where zirconium tetrachloride exhibits a significant vapor pressure) followed by a sublimation step (which conveniently leaves the nonvolatiles behind.) While these procedures effect definite purification, such processing is batchwise and does not result in optimum purification. Early work by The Carborundum Metals Co. and others indicated that fused salts were highly efficient in the removal of impurities from gaseous zirconium tetrachloride. The objective of this work was to develop a continuous fused-salt scrubbing process that would yield high-purity zirconium and hafnium tetrachlorides. The term "fused salt" refers to the molten state of ionic compounds and as used here, specifically refers to alkali metal and alkaline earth halides. Fused salts, because of their many valuable properties, are becoming increasingly im- portant industrially. These valuable properties of the fused salts are: 1) stability at elevated temperatures; 2)low vapor pressure; 3) low viscosity; 4) ability to dissolve many different materials; and 5) good elctctrical conductivity. All but the last property enhances the use of fused salts as scrubbing agents for zirconium and hafnium tetrachlorides. Fused-salt scrubbing may be defined for our purpose as the intimate contact between a gaseous compound and a molten salt with the purpose of removing impurities from the gaseous compound. In this case, the gaseous compound is zirconium tetrachloride which submlimes at 331°C. When this gas is contacted with a molten salt, impurities such as aluminum, iron, and titanium are removed and the resulting product is considered fused-salt scrubbed. Zirconium and hafnium are sold to a purity specification. Generally speaking, normal production without scrubbing is capable of meeting specifications. There are, however, several considerations That make the knowledge of methods of additional purification highly desirable. These are: 1) the control of product analysis; 2) the production of a pure product for special applications; 3) the salvaging of off-specification material; and 4) the use of raw materials with higher impurity levels than 1 he present raw materials. You will note that items 1 and 2 are somewhat complementary to each other and that item 4 assumes that The present process has impurity removal limitations. To better understand the part that fused-salt scrubbing of zirconium tetrachloride plays in the manufacture of zirconium, Fig. 1 contains an illustrated flow sheet of the industrial production of zirconium metal. In referring to Fig. 1, we can point out the specific benefits derived from our ability to purify zirconium tetrachloride. Purification of the crude (hafnium-containing) zirconium

Jan 1, 1962

By R. B. Basham, C. W. Macune

Very small anomalies in oil well temperatures are detected and measured by recording the difference in temperature existing between two thermally sensitive elements which are Spaced several feet apart on a small diameter carrier and lowered into the bore hole. The elements operate in a balanced electrical circuit, sending only a reference signal to the surface as long as normal gradient temperatures are encountered. When either element enters a temperature disturbance, the circuit is unbalanced and produces large recorder deflections for minute anomalies. The system is highly sensitive to small changes in thermal gradients caused by gas or fluid movements and to the boundaries between beds of different thermal conductivities. Typical logs show successful applications of the process to locating gas and water leaks in casing, gas entry. and gas-oil contact. INTRODUCTION Temperature measurements in oil wells have been made for many years in the search for additional sub-surface data. It has been generally agreed that many conditions in the bore hole cause temperature anomalies which, if located and measured, could yield useful information. But it has been recognized also that many of the irregularities, such as those produced by small water and gas leaks in casing, might be very small and therefore difficult to detect with certainty.' Although tem-perature measurements have been made which show anomalies of less than one degree deviation from normal gradient temperatures, the results are usually uncertain and unconvincing. The general practice, therefore. has been to apply temperature surveys only to well conditions known to produce appreciable disturbances, such as large gas movements and cement hydration. The recent demand for additional data has focused attention on the problem of making dependable temperature measurements in the many instances when anomalies are small but none the less significant. It was for the purpose of detecting these minute irregularities in bore hole temperature that the program described in the following text was undertaken. It is emphasized that this presentation is not offered as a complete study, for the process is still partially experimental. But it is believed that the results obtained thus far will be of interest to the industry and will indicate some of the system's potential usefulness. DIFFERENTIAL MEASUREMENT The chief value of differential measurement lies in the fact that a difference between two factors can be measured with a scale of values best suited to that difference, a scale that might be cumbersome or impractical if applied to the factors themselves. When it is known that all factors will be nearly equal in value, and therefore the differences consistently small, it is possible to select a scale which will permit very accurate measurement of the differences. This advantage is in contrast to the difficulty of measuring small increments of a single variable, where the increment must be measured by a large scale which is suitable for measuring the entire factor. Gradient temperatures are usually measured under this latter condition where temperature measuring apparatus must have a scale extending over the range of expected temperatures, say 50' to 25O°F, and it becomes almost impossible to detect small irregularities of less than one degree. The use of large strip chart recorders and divided multiple ranges tend to amplify the small anomaly and make it more pronounced. But the instability of instruments, both

Jan 1, 1952

By Arthur Knapp

The practical application of mud-laden fluids in wells has been the subject of many papers.' However, there seems to have been little investigation of what actually happens when mud-laden fluids are applied to a loose porous sand. The assumption is that the fluids penetrate the sands and that there is some plastering action. The degree of penetration and the relation of plastering action to wall stability is not generally known. This paper describes a series of experiments made in an attempt to observe, in laboratory apparatus, the action of mud-laden fluids under conditions simulating those to be found in a well. For the purposes of this discussion all fluids containing solid matter in suspension are mud-laden fluids. Series I: Penetration of the Pores of Uncemented Sands The subject of the penetration of porous formations by water is discussed in detail in Water-Supply Paper No. 67 of the U. S. Geological Survey. No attempt was made to repeat the experiments described therein. The results of the first experiment of this series are given simply to show the capacity of the apparatus used. The conditions in this first experiment were maintained throughout the remainder of this and the second series, except where noted. The experiments of Mills, McCoy, and others on subsurface flows, adjustments, migrations, etc., deal with the oil, water or gas within the porous beds.V he experiments described herein deal with the conditions immediately surrounding the bore hole.

Jan 1, 1923

By A. J. Lyon

The stability and permanence of any structural material used in aircraft are of paramount importance. The spontaneous hardening, or age-hardening, which takes place in some of the aluminum alloys under ordinary conditions of temperature and atmosphere, is accompanied by an increase in tensile strength and proportional limit and a decrease in elongation or ductility. Within the last few years the introduction of a number of strong and ductile casting alloys led to a study by the Materiel Division, Air Corps, of the permanence of the physical properties in several of these alloys. It has been found that even though some alloys have good properties directly after casting or heat treatment, they are not satisfactory for stressed parts that require a combination of strength and ductility. It has also led to the conclusion that all alloys that can be hardened by artificial aging—heating in a temperature range below 170" C. (340" F.)—will harden spontaneously if allowed to stand for a sufficient length of time. It follows that, in aircraft work where the factors of safety are limited on account of the necessity of keeping the weight of the structures as low as possible consistent with their safe operation, the properties of the alloys in the stable or final condition should be used as a basis for design rather than the properties obtained on the material directly after casting. The work of Wilm in Germany, Hanson and Gayler at the National Physical Laboratory in England, and Merica, Jeffries, and others in the United States, has shown that the spontaneous hardening is characteristic to a greater or less extent in all aluminum-base alloys in which the solubility in the solid state of the alloying constituents decreases with the temperature. It has been shown that, by heating to a temperature as near as possible to the melting point of the material and soaking at that temperature for a sufficient length of time and then quenching or cooling rapidly, a maximum amount of the soluble constituents can be retained in solution and the condition of maximum hardening effect upon aging can be obtained. Also, in ordinary sand and chill castings, without heat treatment, a sufficient amount of the alloying constituents is held in solution to cause important changes in the final physical properties.

Jan 1, 1929

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By J. Chipman, T. P. Floridis

The equilibrium of gaseous H2O-H2, mixtures with liquid iron is used to establish the activity coefficient of dissolved oxygen as log f o = — 0.20 [%O]. Discrepancies in earlier work are explained or eliminated. Additions of cobalt, molybdenum, tungsten, and platinum increase the activity coefficient of oxygen whereas copper and gold decrease it. THE importance of dissolved oxygen as a refining agent in liquid steel has led to a number of studies of its thermodynamic properties. It is the purpose of this paper to examine the effects of a number of alloying elements on the activity of oxygen in the steel bath. As a preliminary to the study of the effects of alloying elements, it seemed desirable to examine certain minor discrepancies in the published data on the properties of oxygen in simple iron-oxygen solutions. The activity and free energy of oxygen in liquid iron were studied by chipman1 in 1933 by means of the reaction h2(g)+-o = H2O (g);K; = PH2O/PH2[% O] [1] The data were in fairly good agreement with calculations from results on the similar reaction CO (g) + O- = CO2 (g); K2 =P CO2/P CO [% O] [2] which had been obtained by Vacher and Hamilton2 as an incidental part of their study of the reaction of carbon with oxygen dissolved in the melt. It was found that the equilibrium ratio k1 was not a true constant but varied with the oxygen concentration in the manner shown in Fig. 1, which is copied from the original paper. This early observation has been refuted in subsequent work but is confirmed in the present paper, and an explanation of the discrepancy can now be presented. In Fig. 1, the two points on the extreme right were disregarded in drawing the

Jan 1, 1959

By D. Harrington

During the past few years, there has been a trend toward the use of rock-dusting, rather than relying on humidifying, or the use of water, to limit or prevent explosions in the coal mines of the United States. This is partly because British coal mines have adopted rock-dusting and, at least in a sense, have condemned the use of water. Moreover, during the past few years, particularly in the latter part of 1922 and in 1923 and 1924, several explosions with heavy loss of life occurred in coal mines of the United States that were known to have more or less extended sprinkling, or humidifying, systems. The sentiment created by these disasters quickly caused a distrust of explosion-prevention methods requiring use of water and simultaneously caused more or less of a stampede into rock-dusting. Much of the wholesale condemnation of watering methods was without adequate knowledge, or at least without adequate consideration, of local conditions in each case, and rock-dusting was adopted largely without sufficient knowledge of how to rock dust safely or correctly. However, mines that had been using watering methods and had suffered these recent serious disasters (notably Dolomite, Dawson, and Castle Gate) instead of abandoning the use of water when operations were resumed after the disaster, greatly extended their watering systems. At the same time they took other precautions as to electricity, ventilation, blasting, etc., and supplemented the watering system with rock-dusting where the latter was likely to be the more effective. The trend toward rock-dusting during the past year or two (succeeding the recent mine disasters) is very similar to the rapid movement toward watering, or humidifying, methods, about 1910 to 1912, after a series of disastrous mine explosions. The Phelps-Dodge Corpn., which operates a large property at Daw-son, N. M., after an explosion in its No. 1 mine in February, 1923, decided that it is dangerous to have all its "explosion-prevention eggs in one basket" and so adopted what may now be termed the Western coalmine explosion-prevention system, in which both rock-dusting and watering are used, supplemented by other up-to-date mining methods and practices; such as exclusive use of modern electric safety lamps, with magnetically locked flame safety lamps for testing purposes; use of

Jan 1, 1925

By H. A. Wheeler

. Page History.................................533 Location .........:.....................536 Geology...............................539 Description of the Eastern Field ... :..................543 Description of the Western Field .........,...........546 Quality of the Oil ................ ,........549 The Oil Sands .,.............................549 Drilling Features'........................., . 551 Well Density...........,.'...............:. 552 Plant Equipment.......................:.'., .554 Market Features..........................555 Production Prices.........,...................557 Royalties and Rentals.........................558 Cost of Oil Leases............................'.558 Operating Expenses..........................559 Operating 'Profits...........................559 Gas Developments ........................560 Gas-Gasoline production ... :....................561 Statistics.......562 History Illinois has SO recently attained the third place in the oil production of the United States that few realize its great importance, or are aware of its highly profitable character. Since 1907 Illinois has furnished about 15 per cent. of the United States output and about 10 per cent, of the world's production. The value of the output in 1913 is estimated at $307000,000, of which about $20,000,000 is profit. The present prosperity dates from 1905, but efforts have been made since 1865 to develop production and geologists have been very sanguine as to its future for over 25 years. Had the oil operators been as confident as the geologists, the field would have been opened at least 30 years earlier. For the rich Eastern Illinois oil field is located along the La Salle anticline, that was mapped 46 years ago by Professor Worthen in the

Jan 1, 1915

By E. F. Adkins, R. I. Jaffee, C. T. Sims

The effect of oxide dispersions on mechanical proberties of cobalt and cobalt-base powder-metallurgy alloys was investigated. This study shows that oxide dispersions added to pure cobalt greatly improve the high-temperature creep resistance of the metal. Dispersions in powder-metallurgy .cobalt alloys were muck less effective. COBALT is extremely valuable as an alloy base for certain high-temperature applications. Important examples may be found in the widespread use of cast and workable alloys in aircraft gas-turbine engines. With the increases in cobalt production in recent years, greater use may be made of cobalt-base alloys for high-temperature applications, provided

Jan 1, 1960

By G. D. Gemmell

Effects of solid-sdutidn alloying with titanium, molybdenum, and tungsten at concentrations up to 10 pct on the strength of pure columbium at elevated temperatures (mainly 2000°F) have been investigated by means of creep-rupture, hot-tensile, and hot-hardness testing and recrystallization studies. ThIS paper presents some results from the initial part of a study of the effects of alloying on the high-temperature strength properties of columbium. The elevated-temperature strength characteristics of pure columbium were first studied. Binary alloys of columbium with titanium, molybdenum, and tungsten containing 1, 5, and 10 pct of the solute elements were chosen on the basis of their high melting points, their known solid solubility in columbium, and results of separate oxidation-resistance studies of columbium alloys. EXPERIMENTAL PROCEDURE All the materials used were of highest purity. A typical analysis of the columbium is shown in Table I. Compositions of the alloys are also given in Table I. To evaluate the strength properties of pure co-lumbium and the alloys at elevated temperatures, creep-rupture, hot-tensile, and hot-hardness testing was done on recrystallized material. To prepare the pure metal and the alloys for these tests, 1- 1b buttons were made in a water-cooled copper crucible, inert atmosphere, tungsten arc furnace. Tapered ingots, 3 in. long, were made from these buttons by a skull-casting technique and these were machined to 1/2 in. diam, swaged to 50 pct reduction (pure columbium at room temperature, alloys at lowest temperature possible without cracking, generally in range 1100" to 1800°F) and heated in vacuum (lo-' mm Hg) for 16 hr at 2550°F for re-crystallization and homogenization. The resulting grain diameter was 0.1 to 0.3 mm. The 10 pct Mo alloy casting was not successfully swaged at temperatures up to 1800°F without cracking and was not included in the test program. Creep-rupture testing was done at constant load in vacuum on cylindrical specimens of 0.16 in. diam, using Instron capsules. The pressure at test temperatures was less than 10-1 mm Hg. Hardneas readings taken on the test specimen before and after testing were used as a check on possible gaseous contamination. Hot tensile tests in vacuum on cylindrical specimens of 0.125 in. diam were also made with Instron equipment at a strain rate of 0.067 min.-l. Hot-hardness measurements were taken with a unit constructed at the Du Pont Experimental Station. The test piece, supported on an alumina anvil, and the molybdenum indenter shaft with sapphire tip is heated in a platinum-wound furnace. The load applied to the pyramid indenter is measured by strain gages attached to a proving ring located outside the hot zone. In the measurements reported here the load was I kg. The tester operates in a vacuum of about 10"5 mm Hg and is capable of temperatures up to 1400°C.

Jan 1, 1960

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By E. C. Bitzer

THE primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the-zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high grade heavy sink product. It appears from this last work that the new separator has definite mechanica1 and metallurgical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator as required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent s development of the inverted or closed- top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1947

By E. B. Phillips, A. E. Miller

The title assigned to this paper permits a discussion of one of the most interesting chapters in the history of the American petroleum industry. Nature was kind to man when she prepared crude oil for him in commercial quantities in the hills of Northwestern Pennsylvania. Most of the refining operations we are now accustomed to apply were either not needed or had been carried out by earth processes ages ago. Such technology as was applied dealt with the physical separation of the valuable components in the crude oil and intermediate products and did not need more than mild refining treatments to bring them to marketable quality. • The pioneer refiners were concerned principally with distilling, dewax-ing and decolorizing operations. The products produced were limited in number and the uses to which they could be put were few. Natural products from the very high grade crudes, then plentiful, supplied the domestic demand and no other markets were open. As time passed, other producing fields were discovered and crude oils of lower natural quality were made available. To refine these grades to a quality expected by buyers, refinery practice had to be changed and new methods found. At the same time the accidental discovery that crude residues could be cracked by dry distillation at atmospheric pressure to produce a much larger amount of lamp oil than had been customary, opened a new vista for the industry. Export kerosene soon became the leading revenue product for all refiners and considerable new technic was added to refinery practice. High sulfur crude oils from Ohio next made their appearance, causing the development of the first commercial desulfurizing process, the sodium plumbite treating method for "sour" lamp oil stocks and the application of fine earth for the removal of "flock." Some improvements in methods of handling lubricating oils and cylinder stock fractions of crude were worked out, but in general, it can be said that the closing decade of the last century found the industry in a stabilized condition. Typical refinery operations of 1900 were simple and were conducted with the single purpose of producing as much export kerosene as possible Light naphthas and fuel oils were a drug on the market and every means

Jan 1, 1928

By Albert Sauveur

To understand this paper properly, the reader must have a clear conception of what is meant by the " critical points " of iron and steel; * and in order to avoid the necessity of tedious references to previous publications on the part of those unfamiliar with the subject, it is here briefly recapitulated. Critictl Points.—If a piece of steel containing, say, 0.50 per cent. or more of carbon, be heated to a high temperature and then allowed to cool slowly, the cooling proceeds at first at a uniformly retarded rate until a temperature of about 700° C. is reached, when there is a sudden " retardation " in the fall of

Jan 1, 1897

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By J. Moore Samuel

Before the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed '(chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing them, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 1, 1917

By R. Laird Auchmuty

The A. I. M. E. Subcommittee on Bituminous Mining has been trying for several years to secure the information that was collected by the Marquette Cement Manufacturing &. on the subsidence of its property caused by mining coal beneath it. The Marquette company was willing to have these data used, but it was impossible to obtain them because the records had been filed away. About two years ago these records became available and the engineering data presented herewith were compiled from them by R. L. Auchmuty, assisted by L. E. Young, who was connected with the collection of the information. On account of the cost, it is impossible to reproduce all of the data here, although the original information is on file with the records of the Committee on Ground Movement and Subsidence. The accompanying charts show representative and average data and give only the engineering information with enough description to tell how it was obtained. It is hoped that all of those connected with the original case will participate in the discussion that this will bring forth. Howard N. Eavenson, Chairman, Subcommittee on Bituminous Coal Mining. PRobably the most complete records of subsidence due to coal mining in the United States are those compiled by the Marquette Cement Manufacturing Co. at LaSalle, 111. These records, covering a period of more than three years, were compiled and used as evidence during the suit of the Marquette Cement Manufacturing Co. vs. the Oglesby Coal Co. at Oglesby, LaSalle County, Ill., in which the cement company successfully endeavored to stop the coal company from mining under its property. Fig. 1 shows a typical section of the geological formation. The cement company was mining the LaSalle limestone which lies about 125 ft. under the surface. The limestone is 30 to 35 ft. thick and underlain by about 15 ft. of shale. The cement company was mining about 20 ft. of the limestone, and in some places 10 to 12 ft. of the underlying shale, by the room and pillar method. The mining of the limestone always preceded the mining of the shale. The coal company was mining by longwall advance methods the NO. 2 seam of coal 42 in. thick underlying the limestone bed by 435 to 470 ft. The coal mine, a very old one, had largely mined out its original property

Jan 1, 1931

By Philip D. Wilson

The mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic 1imestones.of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district, it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft., the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock, the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances a way from the zone of contact metamorphism. The copper was probably introduced during or slightly later than the porphyry intrusion in the form of chalcopyrite and bornite. These primary copper minerals are always associated with pyrite and often occur as rich lenses in a huge mass or shell of pyrite carrying an insignificant percentage of copper. In many instances the copper-bearing solutions were preceded by siliceous solutions and these latter, often persisting during the period of mineralization, have thoroughly indurated the ore-

Jan 1, 1917