Search Documents

By Ross W. Smith, Salim Akhtar

INTRODUCTION Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collectors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By W. R. Ingalls

MANY years ago, I expressed the opinion, in writings and otherwise, that it was possible to desulfurize zinc blende autogenously, i.e., without the use of extraneous fuel, and that at some time this would be accomplished. This opinion was based on thermal calculations and also on observations of the behavior of blende during roasting in different ways, all of which observations tended to confirm the theoretical calculations. Among such observations were things like the following: Once in carrying out the stall roast of cupriferous pyrites as a regular metal-lurgical operation, I was minded to charge a stall with lump blende, ranging from walnut to egg size, as I recollect, following the same procedure as with pyrites, and setting fire to the kindling wood, observe what would happen. The blende charge ignited well enough and bravely began to burn, quite actively the first day, at a diminished rate the second day, while on the third day burning ceased and the charge quickly became cold. It was just like trying to set a grate full of anthracite afire with insufficient kindling wood. The volume of air drawn through the stall was too great, quickly cooling the entire contents below the ignition temperature, which means, of course, that burning ceased.

Jan 12, 1922

Jan 1, 1921

By I. Iwasaki, R. H. Heerema

The presence of calcium and magnesium ions in iron ore pulps that are upgraded by selective desliming can result in indiscriminate flocculation of both iron oxide and siliceous gangue slimes. The removal of these alkaline earth cations in pulp solutions by chemical precipitation was ineffective as a means of deflocculation of quartz. It was shown by using various techniques (electron micrographs, abstraction, and streaming potential measurements, and cationic flotation tests) that heterocoagulation between the precipitates [Mg(OH)2, hydroxyapatite, and CaCO3] and quartz particles was the reason behind that observation. In addition, the precipitates adversely affected the recovery of quartz by cationic flotation, due to slime coating, a case of heterocoagulation. Magnesium hydroxide produced a uniform layer of coating across the quartz surface, while hydroxyapatite and calcite produced discrete, localized deposits dotting the surface.

Jan 1, 1981

By Robert H. Merrill, Raymond M. Stateham

Recently, the Denver Mining Research Center of the U.S. Bureau of Mines began tests to detect hazardous or potentially hazardous conditions in or around mines with infrared measurement devices. Among the many potential uses of infrared detection techniques are the location of misfires, underground mine fires, combustion in waste dumps, underground water courses and loose rock. However, the primary emphasis has been placed upon the detection of loose rock in roofs, pillars and faces in underground mines. The rock along the edge of an underground opening is subject to two temperature environments: the temperature of the air in the opening, and the temperature of the rock surrounding the opening. Assuming that the rock on the edge of the opening is solid, the rock will reach an equilibrium temperature that depends upon the temperature and flow of the air, the thermal conductivity of the rock and its ambient temperature. Presume that a loose rock exists among this solid rock; because there is a temperature barrier, to some extent, between the loose and the solid, the loose rock will be affected more than the solid rock by the temperature of the air. Therefore, depending upon the temperature differences between the rock and the air, the loose will be warmer or cooler than the solid.

Jan 1, 1970

By George W. Healy, Ko Yamaguchi

In typical calorimetry the energy given off by a material under study is transferred to a water bath, whose temperature is sensed by a thermometer; for correct measurement the water bath must attain a uniform temperature to which the thermometer must respond. This introduces two sources of error, non-uniformity of the heat sink and a time lag until its temperature is registered. These errors may become important where a rapid process such as solidification of metals and alloys is being studied by means of Oelsen'sl quantitative thermal analysis. To overcome this difficulty, a calorimeter sink was conceived in which the water bath is replaced by a copper coil, which serves simultaneously as heat

Jan 1, 1967

By E. E. Krist, W. H. Sweetser

Sampling of an orebody has a number of purposes. In the initial phase, it is necessary to define the limits of the orebody and mineral content to the extent that it can be stated whether it is, in fact, an economic orebody. Also, samples must be generated so that geological and metallurgical evaluations can be made. Finally, when sufficient information concerning the geology, mineralogy, and metallurgy are known, a mining method and plan can be developed and the metallurgical; plants constructed to process the ores as they become available. With today's large, complex open pit copper mines, single sampling methods would be inadequate. Diamond drilling, percussion drilling, underground shafts and drifts all play a part in the total orebody, definition. At Anamax Mining Company's Twin Buttes mine, sampling and orebody definition.wil1 eventually lead to the existence of three metallurgical processing plants and, perhaps, an underground mining operation. A 30 000 tons per day sulfide concentrator was placed in operation in September 1969 and a 10 000 tons per day oxide leaching plant was placed into service in May 1975. The aim of this presentation is to historically discuss the orebody sampling that has been done at Twin Buttes, briefly describe the orebody, and discuss the analytical methods currently used to assist the geologist, metallurgist and mine planner in their respective evaluations.

Jan 1, 1978

NEW MEMBERS The following list comprises the names of those persons who became members during the period Apr. 10, 1919, to May 10, 1919. BEAVER, JAMES J., Supt., Mech. Ore Loaders, Tennessee Coal, Iron & R.R. Co., Box 62, Bessemer, Ala. BLACKWELDER, ELIOT Geol. & Prof. of Geol., Univ. of Ill., Urbana, Ill. BRAECKE, GUSTAVE E., -Min. Engr., Mgr., Societe Curas et Soldado, La Carolina, Spain. BRINK, CYRIL GORDON, Reduction Officer, Charge of Reduction Works. Fairview Devonian Montrose Gold Mines, Ltd., P. O. Sheba, Transvaal, So. Africa. COMERFORD, JOSEPH S., Chief Chem. & Met., American Manganese Steel Co., New Castle, Delaware. DROSDOWSKI, N. C. V., Asst. Supt.,, The Spassky Copper Mine, Ltd., Karagandy, Akmolinsk, Oblast, Siberia. DUNGLINSON, GEORGE, JR., Asst. to Gen'l Mgr., Norfolk & Western Railroad, Bluefield, W. Va. FARAGHER, PAUL VANCE, Research Fellow on Light Metals, Mellon Institute, Pittsburgh, Pa.

Jan 6, 1919

By R. K. Waring

A KNOWLEDGE of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunatel, the results vary widely, particularly at higher tempera-tures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason deter-minations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zinc-rich phases in the solid state, 1,2 and methods in which the. samples are taken while the bath is liquid and at the desired temperature. 3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investi-gations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility.

Jan 1, 1934

W. E. RUDER, Schenectady, N. Y. (written discussion?).-To many members of the Institute, papers like this one by Prof. Jeffries, and that on "Reversal of Inheritance" by Prof. Howe, may seem highly academic. Aside from their direct application to all heat-treating processes, to my mind, the establishment of a physical fact and the correlation of facts into a definite law are in themselves ample justification for immense effort. A law, once established, cannot be ignored by those who carry the work along to practical ends. In studying both papers, it seems to me that each author is more concerned with defending a theory than with explaining the individual results as published by various investigators. Take, for example, my sample of pressed electrolytic iron, frequently referred to by both. Prof. Howe, defending inheritance, says that the grains on the second (1300° C.) heating inherited their size from the mother austenite. Prof. Jeffries, defending reversed inheritance, elabor-.

Jan 4, 1918

By Edwin H. McKee

Eruption of rhyolitic ash-flow tuffs in the area of the McDermitt (Cordero) caldera began about 17.4 million yr (m.y.) ago and continued for about 1.5 m.y. During this period of silicic eruptions, a circular area about 30 km in diameter collapsed to form a caldera that subsequently filled with sedimentary and volcanic rocks. A total of more than 200 km30f silicic rocks was erupted from the volcano. The final phase of igneous activity, about 15.0 m.y. ago, included resurgent doming and intrusion in the south-central part of the caldera. Three to 4 m.y. later (-1 2 m.y. ago), hydrothermal solutions using the northern part of the caldera ring fractures as conduits deposited silica, cinnabar, pyrite, alunite, and other minerals in tuffaceous lake beds and volcanic rocks accumulated within the caldera. The ore-forming solutions may have been a residuum from the silicic magma, or connate water, or ground water heated by the still-hot resurgent magma in the central part of the caldera. The source of the mercury and other elements has not been identified.

Jan 1, 1977

By Donald H. Yardley, A. Aly Selim

An economic simulation model was developed to predict the amount of copper recovered from copper oxide deposits, and the cost of producing it as a function of the deposit parameters. The economic simulation model includes programs for fragmentation design and cost, copper extraction, solution distribution and recovery, effluent solution cut-off grade, and financial analysis. Cost and price indices were also developed to evaluate the economic feasibility of in situ leaching operations as a function of their starting date. Application of the models to various hypothetical properties having the same area and different ore thickness shows that the effluent solution cut-off grade does not vary with the ore thickness nor with its grade. The percent of copper recovery is, however, shown to increase with the increase in the ore thickness and is independent of the ore grade. It is also shown that while the profit per unit of extracted copper increases with the increase in ore grade or ore thickness, the rate of return on total investment does not show any correlation.

Jan 1, 1979

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By L. O. Howard

THE practice of using acid-lined converters at the plant of the Old Dominion Copper Mining & Smelting Co. was discontinued early in January, 1913, and they were replaced by basic-lined converters. The new equipment consists of one electrically operated 12-ft. upright converter stand and two basic-lined shells for same. These shells are provided with twenty-four 1 1/4-in. tuyères. The mouths are 5 ft. in diameter. Owing to the fact that there is no bedding system or other large storage capacity between the mine and the smelter, the furnaces must handle as fast as produced ore and concentrates, which may vary considerably from day to day, both in tonnage and copper content. Consequently the converter is often crowded to its utmost capacity by the frequent fluctuations in the daily matte supply. From the foregoing, it will be seen that in no way can the converter be favored by running light charges or by transferring to it from other stands in operation. Neither can it regularly be allowed to cool between blows, and only occasionally can it be run at as low a temperature as might be wished. No copper precipitate or other foreign material high in copper is available to help out the tonnage. Repairs and alterations or the removal of defective tuyères must wait until such time as a slight falling off in the matte supply-allows the converting operations to ease up. These variable conditions all combine to interfere with the systematic operating of the converter.

Jan 7, 1914

Jan 1, 1920

By Bryon W. Cheever

While working upon the processes which have been descaribed from time to time in the Transactions of the Institute for the estimation of these elements, I discovered that certain reactions take place under certain conditions which if overlooked, give erroneous results. Some of these reactions are new, to me at least. Estimation of Manganese. A weighed sample is dissolved in nitric acid and the manganese precipitated by potassium chlorate in the usual manner, care being taken to add some strong nitric acid at the last, and boil, to completely destroy the chlorate. Filter through purified asbestos, suck the filter dry with an aspirator; then wash with HNO3(1.40sp). gr.) until the acid comes through clear, and again suck dry with the aspirator. The nitric acid used for washing must be free from nitrous acid, for this acid reduces the peroxide of manganese; the lower oxide thus formed is dissolved by the strong nitric acid and is carried through the filter; some manganese also will nearly always be dissolved if the precipitate is washed with water. The nitric

Jan 1, 1886

The new saw mill at Cache Bay of the Geo. Gordon & Co., Ltd., a subsidiary of International Nickel Co., of Canada, is equipped with the first fully electric saw carriage drives in Ontario. It has a capacity of 120,000 ft of lumber in an 8-hr shift. About half of the mill's production is high grade white pine lumber which is shipped to the general market. The other half, red pine is used in the mining operations of International Nickel in the Sudbury district, 55 miles west of Cache Bay. [ ] Inco with a potential need of 77 million board ft a year, gets only part of its supply from the new mill. The milling firm became an Inco subsidiary Jan. 1, 1948.

Jan 1, 1952

By M. F. Williams, L. G. Hendrickson

In classification of pulps bearing magnetized ferro-magnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in flocs. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used.

Feb 1, 1956

Conservatively, there are a half million square miles in Australia just like it, this spot near the western border of New South Wales. Space and distance are the elements. Mulga tree and salt bush, silvery under the sun, hug the ground too close to make welcome shade. To the east a wrinkle on the empty plain marks the line of lode, the Broken Hill bonanza. Strangely, the outback stops at a cyclone fence close by the ridge. Beyond, the peculiar island continent vegetation flourishes with the same frosty patina of the mulga and the salt bush. A city of 30,000 people is hidden behind the screen of vegetation. Once, the city was ugly and the people miserable from marching, flying sand. Now with a protective screen of vegetation, it is an oasis in the outback. The secret of the oasis is the fence. All regeneration plans failed until it was built to keep kangaroo, rabbit, sheep and man from destroying the plantations.

Jan 10, 1964

By C. R. Garr, A. R. Troiano

FLAKING or hair-line crack formation has been a major problem confronting the producer of large alloy steel forgings.' Today it is generally conceded that hydrogen in one or more forms in alloy steel sections is a requisite for flaking. Hence an obvious remedy is a thermal cycle that reduces the hydrogen content to some low level. In practice, this generally means holding the material at some subcritical temperature for a period of time depending on the size of the ingot or forging. Another method that will suffice in some cases is to cool large forgings slowly, i.e., bury in ashes. In practice, this hydrogen bake is sometimes accemplished inadvertently by a series

Jan 1, 1958