Search Documents

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920

By J. G. Eberhort

ThE literature of surface phenomena shows that, except for most of the rare-earth elements, surface tensions have now been determined for almost every liquid metal. The situation for liquid metal oxides is, in contrast, characterized by a great scarcity of surface-tension data. A surface-tension correlation between these two classes of substances has been found which provides a means of estimating unknown liquid-oxide surface tensions from the corresponding known liquid-metal surface tension. Lf the surface tension of the liquid metal is a(M) and that of the liquid metal oxide is o(M,Oy), then oxides of all stoichiometries can be brought into one correlation if is plotted against with the surface tensions taken at the respective melting points. The available data is displayed in this fashion in Fig. 1 where the relationship between the surface tensions of the two classes of liquids is found to be The correlation in Fig. 1 is based on data found for nine liquid metal oxides and the corre- sponding liquid metals In cases where several sur-face-tension determinations were available on the same substance, higher values were generally favored over lower ones because they usually indicate greater Sample purity. All of the metal-metal oxide pairs are in good agreement with Eq. [I] except for B-Bz03. The reason for the departure of this pair from the correlation is not understood. To estimate the surface tension of other liquid metal oxides the corresponding liquid-metal surface tension must be found. A nearly complete bibliography of the surface tension of liauid elements is available in the 46th edition of the Handbook of Chemistry and physics. Some additional references on metals are included here for convenience Se,26Sr,'?ThanduZ5). It is also possible to estimate the surface tension of a solid metal oxide or metal from the corresponding liquid-state data. As a liquid material is cooled through its melting point the surface tension increases abruptly by an amount Ao. bondi' has estimated that the maximum value of Aa at the melting point is Ao = Ahf/A [2] where Alzf is the heat of fusion per atom and A is the area per atom in the interface. Thus with heat of fusion and crystallographic data the surface tension of a solid at the melting point can be estimated as o + Ao.

Jan 1, 1967

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By J. H. McCormick

This plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor, because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyani-dation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz was sharp and sandy, however finely ground, and rather difficult to slime. The mechanical equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp., 0.68 c.; 300 to 500 hp., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower. The plant as above described was operated from May, 1915, to the end of the year, when an additional Dorr thickener and a 12 by 12-ft. Portland revolving filter were added, increasing the nominal capacity of 100 tons per 24 hr., but not the percentage of extraction. The combined treatment, at a cost of $1.48 per ton, saved 90 per cent. of the gold arid

Jan 1, 1919

By Charles M. Rolker

The Mariposa estate, a grant made by the Mexican Government to Juan 13. Alvarado, during the time when California was still under the dominion of Mexico, was purchased in 1847 by J. C. Fremont, and the United States patent issued to him in 1856. By sale, or its equivalent, money advanced, the property came into the hands of the Mariposa Company, June 25th, 1863, and through a varied existence of work and temporary inactivity, has as yet been kept as an undivided property, and rests at present with the Mariposa Land and Mining Company of California. I pass over this period of 15 years without giving the history of the ups and downs of the estate, partly because it is familiar to many, and also because I think in such a case this paper would assume too much the character of a narrative. The estate is situated in Mariposa County, California, about 170 miles southeast of San Francisco. It begins in lat. 37' 26' 38'' north, and long. 119' 55' west, and runs 6 miles north; thence 69 miles west; thence 5 miles northwesterly towards the Merced River; thence 84 miles southerly; thence 3 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 2 miles southerly; thence 2 miles easterly; thence 1 mile southerly; thence 2 miles easterly; thence 1 mile northerly, and thence 2 miles easterly to the place of the beginning; embracing 44,387 acres (70 sq. miles) more or less. To describe this vast estate in detail as to its full geology, its numerous quartz veins, its many facilities to exploit them and work them by cheap methods, would lead me further than I intend to go at present, and I will content myself to describe the latest workings of the company and its immediate field of operations. As long ago as 1860 the late Dr. Adelberg advised the running of an adit from the northwestern edge of the estate at Benton Mills 011 the Mereed River. His object was to undercut the deepest workings of the then paying mines on the estate—the Pine Tree and Josephine. Following this advice, the tunnel known as "River Tunnel " was commenced. Its entrance is in S. 5, T. 4, s. R. 17 E. It is run in

Jan 1, 1879

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

DEFORMATION lines, also called etch markings or strain markings, are noneffaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries.1 Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrette to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation required for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted deformation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson' observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brick9 noted that deformation lines in 70-30 brass apparently associated with {111} planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards11 reported that in copper cold rolled less than about 50 pct few strain markings were apparent but for higher. reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass

Jan 1, 1948

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By E. H. Dix

The work of Merical and other investigators indicates that the phenomenon of age-hardening in alloys of the duralumin type is primarily dependent upon the variation in the solubility of copper with temperature. In addition to copper, however, these alloys contain small amounts of magnesium, silicon, manganese and iron, which may affect the age-hardening either directly or indirectly. The effect of these elements on the solubility of copper and on the manner in which this solubility varies with the temperature is of considerable interest, therefore. The effect of magnesium is of especial interest because apparently it exerts a marked effect on the natural or room-temperature aging of alloys of the type described.2 A series of investigations3 has been in progress in the research laboratories of the Aluminum Company of America to determine the functions * Metallurgist, Aluminum Research Laboratories. f Metallurgical Division, Aluminum Research Laboratories. Formerly with Metallurgical Division, Aluminum Research Laboratories. 1 P. D. Merica, It. G. Waltenberg and H. Scott: Heat Treatment of Duralumin. U. S. Bur. Stds. Sn. Paper 347 (1910). 2 M. Gayler: Constitution and Age-Hardening of Alloys of Aluminum with Copper, Magnesium, and Silicon in the Solid State. Jnl. Inst. Met. (1922) 28, 213. W. Fraenkel: Vergutbare Aluminiumlegiengen. Ztsch. Melallkunde. (1920) 12, 427. E. H. Dix, Jr.: Note on the Microstructure of Aluminum-Iron Alloys of High Purity. Proc. Amer. Soc. Test. Mat. (1925) 26, Pt. 2, 120. E. H. Dix, Jr. and H. H. Richardson: Equilibrium Relations in Aluminum-copper Alloys of High Purity. Trans. A. I. M. E. (1926) 73, 560. E. H. Dix, Jr. and W. D. Keith: Equilibrium Relations in Aluminum-manganese Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1927) 315. E. H. Dix, Jr. and A. C. Heath, Jr.: Equilibrium Relations in Aluminum-silicon and Aluminum-iron-silicon Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1928) 164. E. H. Dix, Jr. and F. Keller: Equilibrium Itelations in Aluminum-magnesium Alloys of High Purity. Proc. Inst. Met. Div., A. I. M. E. (1920) 351. E. H. Dix, Jr., F. Keller and R. W. Graham: Equilibrium Relations of Aluminum-magnesium Silicide Alloys of High Purity. Trans. A. I. M. E., Inst. Met. Div. (1931) 404. W. L. Fink and K. R. Van Horn: Constituents of Aluminum-iron-silicon Alloys. Trans. A. I. M. E., Inst. Met. Div. (1931) 383.

Jan 1, 1932

By P. F. MINISTER

AT Lime Spur, Mont., the East Butte Copper Mining Co. has been quarrying limestone for twenty years. The quarry is beside the Northern Pacific R. R. in the Jefferson River canyon, 4 ½ miles east of Cardwell, at Lime Spur, Montana. HISTORY This quarry was opened early in 1900 by Dan Morrison of Whitehall, the discoverer of the Morrison cave, to supply a demand for smelter flux. Limestone was sold to the Pittsmont smelter of The East Butte Copper Mining Co. and to the Butte Reduction Works. As no particular effort was made at the quarry to select the rock that delivered to the smelters was unduly high in magnesia and impurities. The East Butte com¬pany, therefore. Bought the quarry. in 1909 and confined operations to the high-grade beds in order to supply rock of the desired purity for its own smelter and the Butte Reduction Works until the latter shut down. It also developed a market for some of its rock with the sugar factories. The latter market increased until in later years all rock, larger than 4 in. in size over a bar grizzly, was being shipped to the sugar factories, and the rock smaller than 4 in. was being used as a flux in the blast furnaces at the Pittsmont smelter. In 1924, the East Butte concluded a contract with the Anaconda company for the treatment of its ores, and the Pittsmont -smelter -was shut down: which made the minus 4-in. rock a useless by-product. Since there was not enough revenue in the sugar rock alone and also because of limited waste room it became necessary, if Lime Spur was to continue to operate, to increase- the proportion of plus 4-in. rock and to develop a market for the minus 4-in.

Jan 1, 1930

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identi-fied with our modern "Age of Steel" is a relatively brief interval com-pared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the fore-runner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935

The General Committee met in the Treasury Building at Washington on Oct. 6 and 7. At the first meeting, Cornelius P. Kelley was appointed chairman, and Paul Armitage, secretary. Sub-committees were ap-pointed on Invested Capital, Mine Valuation, and Depletion and De-preciation. On Oct. 7, the reports of these committees were submitted to the General Committee and were referred to the Executive Committee. A motion was carried that the Executive Committee he constituted a permanent committee to continue the work of the Committee, with full power to acid to and increase its membership, that. as thus increased, it should constitute a permanent organization to act- and cooperate with the Treasury Department in matters of mining taxation under the Federal Income and Excess Profits Tax Laws. Thereafter the Executive Com-mittee met and formed a permanent committee as follows: Cornelius F. Kelley, chairman, 42 Broadway, New York City. J. L. Darnell, office of the Commissioner of Internal Revenue, Wash-ington, D. C. J. Parke Channing, 61 Broadway, New York City. Walter Douglas, 99 John St., New York City. R. V. Norris, 542 Second National Bank Bldg., Wilkes-Barre, Pa. J. E. Spurr, Engineering and Mining Journal, 10th Ave., and 36th St., New York City. W. G. Swart, 808 Selwood Bldg., Duluth, Minn. J. P. Finley, 45 Cedar St., New York City. W. A. Williams, Bartlesville, Okla. F. S. Peabody, Peabody Coal Co., McCormick Bldg., Chicago, Ill. Matthew C. Fleming, 71 Broadway, New York City. H. B. Fernald, 54 Wall St., New York City. William G. Mather, Cleveland, Ohio. Walter Fitch, Eureka, Utah. Arthur Thacher, 900 Security Bldg., St. Louis, Mo. John P. Gray, Coeur d'Alene, Idaho. Paul Armitage, secretary, 233 Broadway, New York City.

Jan 12, 1919

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

Report of Secretary TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I have the honor to present the following report for the calendar year 1920 The activities which-seem to call for special com¬ment are THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published The Bound Volumes, as usual, contain all the papers in full and discussions thereof FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent greater than the members paid when the Institute was founded forty-nine years ago This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of\the national engineering societies has rendered the situation more difficult for us MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St Lours, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine

Jan 1, 1923

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By R. M. Hudson

Equilibrium constants have been determined for the jeaction C (in steel) + H2O = CO + H2 as a function of carbon content (0.013 to 0.74 ujt pct) and temperature (1200° to 1800°F) by using a flow system in which the water-vapor content of various gas mixtures containing hydrogen, carbon monoxide, and nitrogen was systematically controlled. The equilibrium partial-pressure ratio K1 = PcoPH2/PH2O was obtained for two low-carbon steels and four Fe-C binaries from a series of runs made at each temperature. By comparison of Ki with the analogous ratio for the reaction C (graphite) + H2O = CO + H2, the activity of carbon in steel (ac) was comDuted for each temperature and carbon content studied. From these data values of the equilibrium constants for two other carburization-decarburiza-tion reactions of importance were estimated. The chemical compositions of the two steels and four Fe-C binaries used are given in Table I. Specimens of Steel E were cut from a 0.035-in.-thick commercially box-annealed and temper-rolled lot of a low-carbon low-metalloid steel. Steel F was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to a 0.059-in. thickness. Fe-C binaries A, B, C, and D were vacuum-melted and poured, hot-rolled, pickled, and cold-reduced at the Laboratory to furnish specimens 0.035 in. thick. Sheet specimens were cut from all lots to approximately 3/4 by 3 in. by gage and were vapor-degreased with trichlo-roethylene and weighed before heat treatment. Heat treatments were carried out in a hinged-top Hevi-Duty electric furnace with a Vycor-glass tube. When the furnace was at the desired

Jan 1, 1965

By H. C. Heard

The review by Professor J. C. Jaeger (Chapter 1) briefly summarizes and discusses a select group of papers by various workers dealing primarily with aspects of fracture in brittle rock materials. Professor Jaeger's treatment is primarily concerned with the correlation of phenomenological and theoretical failure criteria with empirical results from short duration tests at ambient temperatures and generally at low lithostatic and interstitial fluid pressures. As engineering rock mechanics becomes more concerned with new techniques of mineral exploration and production at increasingly greater depths in the crust, it is well to be aware of the effect of the environment -that of the superposed stress field upon the lithostatic and interstitial fluid pressure, the temperature and the duration of the loading upon the failure of rocks either by fracture or flow. All results to be discussed here are from laboratory tests on small homogeneous samples, thus caution should be used in the direct extrapolation of these results to large inhomogeneous rock masses having quite different boundary conditions in the earth. The purpose of this supplement is to briefly point out the major effects of these parameters as examined singly, with all others held constant, and to cite some recent results which apply to the main theme on the brittle failure of rocks. The total stress field imposed upon a small volume of porous and permeable rock in the earth's crust may be thought of as the sum of an applied differential stress, plus a lithostatic pressure, plus an interstitial fluid pressure. The differential stress portion may be completely specified by nine components, six shear and three normal. If the small volume element is in rotational equilibrium, by suitably choosing our coordinate axes we may resolve these nine components into the three principal com-

Jan 1, 1967

By N. F. Fiore, M. F. McGuire

THIS communication describes a series of experiments in which dislocation etch pitting was used to ascertain the depth of damage in crystals which were mechanically polished or which were cut with either a commercial metallographic cut-off wheel,* a com- All specimens were cut from single crystals of American Smelting and Refining Co. 99.999+ pct pure copper which were grown from the melt by the Bridge-man technique. The test specimens were disks, with faces being (111) planes and the disk axis a (111) direction. The disks were annealed in a vacuum of 10-5 Torr for 24 hr at 950°C prior to cutting or polishing and were given a light electropolishing in an ortho-phosphoric acid bath before etch pitting. Both Youngs1 and Livingston's2 reagents were used for etch pitting and the reagents gave identical quantitative results; however Livingston's reagent produced less staining and so all photomicrographs shown are of {111) surfaces etched with this solution. The surface of the annealed crystals showed well-defined subboundaries and a density of dislocations of about 1 X 106 per sq cm excluding those present in subboundaries, Fig. 1. The depth of cold work produced during mechanical polishing was determined after an annealed specimen was mounted in a paraffin holding block to protect it from extraneous damage. The exposed (111) surface was ground on metallographic papers and then polished on billiard cloth through 0.05-p alumina abrasive. It was necessary to remove about 0.3 mm (-0.01 in.) to obtain a structure representative of the annealed sur- face, indicating that the crystal was damaged to this depth during mechanical polishing. The cold work caused by standard cutting methods was measured in another series of tests in which cuts

Jan 1, 1967