Search Documents

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

By J. G. Eenink, R. A. Cunningham

One phase has been completed of a laboratory invesrigation of formations with relatively high permeability under conditions of overburden, formation and mud coltrmn pressures. The following statements are based on these tests within the limitations described. Drilling rate decreased when mud column pressure was greater than formation pressure. The decrease was primarily due to a layer of cuttings and mud particles held to the hole bottom by the difference in pressure. Much of the force of the bit was wasted in this layer and was unavailable for penetrating virgin formation. Adequate jet velocities helped clean the filter cake and chips away and resulted in increased drilling rate — the higher the jet velocity the faster the drilling rate. Drilling rate increased slightly when formation pres sure was greater than mud column pressure. The i11(reuse resulted from cleaning the hole bottom as formarion fluid flowed into the borehole. Overburden pressure had practically no effect on drilling rate. INTRODUCTION Some formations are difficult to drill in a wellbore hole but are easily drilled under atmospheric conditions in the laboratory. The reasons for this apparent difference in drillability are not fully understood. An increase in formation compressive strength causes a reduction in drilling rate. It has been shown by Griggs1, Handin2 and others3-1 that formation strength increases under conditions of high hydrostatic stress. Based on these results, a decrease in drilling rate would be expected with increased drilling fluid pressure in formations of low permeability having low formation fluid pressure. Such a decrease has been shown by Murray. et a1 and Eckel" This effect holds even when using nitrogcn under high pressure as the drilling fluid (unrc-ported tests from the Hughes laboratory). Poor bottom-hole cleaning may account for decreased drilling rates. Even though it may not be easily explained, evidence of poor cleaning can easily bc seen. One evidence is the increased drilling rate that accompanies decreased balling obtained with addition of oil in some muds used to drill shales.4,7,3 Many variables can affect drilling rates. These may include mud composition and properties, formation properties, bit types and operating conditions, formation fluid, mud column and overburden pressures. These must be studied a few at a time under carefully controlled conditions which simulate actual conditions as closely as possible. The purpose of this work was to investigate effect of overburden, formation and mud column pressures on drilling rates in permeable formations. These tests were suggested by conditions shown in Fig. I. Represented is a borehole drilled into a formation with relatively high permeability. In the vicinity of the hole bottom there exists a mud column pressure, P a formation fluid pressure, P and an overburden pressure, The mud has low water-loss properties and sufficient weight to more than overbalance the formation pressure. Laboratory investigation included a range with formation pressure greater than mud column pressure. NOMENCLATURE Pm mud column pressure = pressure of drilling fluid or mud at hole bottom Pf, formation pressure = pressure of fluid in intersticies of formation

By Arnulf Muan, Klaus Schwerdtfeger, L. S. Darken

The equilibrium ratios CO/CO, of. a gas pharse coexislitrg with selected oxide phase assemblages of the system "FeO"-MnO-SiO2 and metallic iron have been determined at 1150°C. The data obtained are combined wilh the thermodynamic data on fayalite (Fe2SiOi) and "FeO"-MnO solid solutions to derive the actiuity-coiHpQsiUon relations for the various oxide components of the olivine (Fe2SiO4-,lIn2Si04) and pyroxenoid (standard free energies of formation of ferrosilile (FeSiO,), tephroite , and rhodonite from their oxides have been evaluated. In the Appendicc~s by Darken and Schivcerdtjeger the ideal solution law for solid deri oed. THE quaternary system Fe-Mn-Si-0 is of interest in many important phases of iron- and steelmaking. For instance, reduction in the blast furnace of ores containing Fe-Mn silicates, deoxidation of liquid steel with Mn-Si alloys, formation and subsequent alterations of oxide inclusions in steels, and the oxidation of manganese- and silicon-containing steels during processing are all governed largely by the thermodynamic relations existing in the system Fe-Mn-Si-O. Although the equilibria between liquid iron and Fe-Mn silicates have been studied in detail previously,' experimental data are lacking for equilibria among the solid phases. The present paper provides such data for a selected temperature, 1150°C. I) PREVIOUS WORK The general feature of subsolidus phase relations in the system iron oxide-manganese oxide-silica under strongly reducing conditions is known.' Fig. 1 represents an isothermal section at 1150°C. The phases present, in addition to silica, are three solid-solution series, viz.. the oxide solid-solution series "Fe0"-MnO (manganowiistite), the orthosilicate solid-solution series Fe2SiO4-Mn2SiO4 (olivine), and the metasilicate solid-solution series FeSi03-MnSi03 (pyroxenoid). The "FeO"-MnO solid solution is continuous between the two end members wustite and manganositeV3 as is the orthosilicate series between the two end members Fe2SiO4 and Mn2 SiO4. 4 The metasilicate solid solution, on the other hand, extends only part way from the MnSi0.l end member toward FeSiO because the latter end member is unstable relative to the phase assemblage fayalite + silica. The letters a through m in Fig. 1 identify end members of the individual solid phases dealt with [for instance, c designates fayalite (FeZSiO4) in equilibrium with wustite, e designates fayalite in equilibrium with silica, and so forth]. In addition to the phase relations there are some thermodynamic data available for the end members of the silicate solid solutions and for the "FeO" -MnO solid solution. The free energy of formation of fayalite (Fe2Si04) from its oxide components has been studied by several investigators. Unfortunately, the data obtained show considerable discrepancies. According to recent tabulations by Kelley, the change in standard free energy Affn for the reaction

Jan 1, 1967

By F. M. Smith, R. H. Moore, J. R. Morrey

Electrodiffusion in y cerium reported by Henrie has been confirmed and a Preliminary estimate made of the relative rates of electrodiffusion of iron, cobalt, and nickel. These diffuse to the anode at rates decreasing in that order. In addition, copper and manganese exhibit slow, but detectable, diffusion to the anode and molybdenum exhibits detectable diffusion to the cathode. The electrodiffusion of carbon, .zirconium, antimony, magnesium , and silicon in y cerium could not be detected. Iron and cobalt diffuse in y cerium at rates proportional to the current density and with no apparent dependence on temperature. Decreasing polarization of iron and cobalt with increasing temperature, which cancels the expected rate increase, would account for this behavior. The electrodiffusion rate of iron in y uranium and in E plutonium has been measured. Diffusion of iron is anode-directed. Tin was found to diffuse to the cathode, in y uranium, at an appreciable rate. In all of these solvent metals, negative ions diffuse to the anode and positive ions to the cathode. The potential field effect appears to account satisfactorily for these results. FROM early experimental work summarized by Jost1 and Seith,2 the driving force for electrodiffusion was attributed to the potential field acting on ions in a metal. More recently, Heuman,3 Wever,4 and Huntington5 have shown that momentum interchange between conduction electrons and mobile entities in the metal contributes to electrodiffusion. Electron momentum interchange is anodically directed and the direction of diffusion resulting from the field force is dependent upon the charge on the diffusing entity. These two effects may either reinforce or oppose each other. Glinchuk6 has pointed out that momentum transfer in defect conductors should be cathode-directed and this appears to be the case as demonstrated by wever's4 work on iron. Barnett's7 work, on the other hand, indicates that, even in defect conductors, electrons show a negative E/m ratio when accelerated with respect to the lattice and should lead to anode-directed momentum transfer. In discussing this problem, Wever and seith8 suggest that defect electrons interact preferentially with activated ions so as to allow a net movement toward the cathode while still maintaining an electron momentum transfer in the anode direction. Williams and Huffine9 and Henriel0 have demonstrated that electrodiffusion may be useful for purification of yttrium and cerium. In yttrium, Williams and Huffine note that movement of several metallic impurities toward the anode is in keeping with observations in most other metallic systems and indicates that yttrium remains a normal electronic conductor at least to 1230°C. Close inspection of their data shows, however, that oxygen, nitrogen, and the transition elements diffused toward the anode, while nontransition elements diffused toward the cathode. This suggests that potential field effects may have been appreciable. The present work was concerned with the applicability of electrodiffusion as a technique for purification of plutonium, but, because of the obvious hazard inherent in work with this metal, experiments to develop the technique were carried out using cerium and uranium. The results of electrodiffusion measurements on these metals and on plutonium are reported here. EXPERIMENTAL The metal specimens prepared for this work were 6 in. long, 1/4 to 1/2 in. wide, and 1/16 to 3/32 in. thick. The uranium specimens were machined from a bar which analyzed 310 ppm Fe and the electrodiffusion of iron was followed by spectrographic and by chemical analysis. Cerium and plutonium specimens were cut from sheet rolled from ingots obtained from molten salt-metal equilibrations during which radioactive tracers were introduced. The electrodiffusion of the tracers was subsequently determined by counting methods. The specimens were electrolyzed between nickel electrodes containing resistance heaters used to equalize the specimen and electrode temperatures, thereby reducing thermal gradients. The temperature of the electrodes adjacent to the ends of the specimen was measured with chromel-alumel thermocouples which were connected to the heater controls. The surface temperature of the specimen at a point midway between the electrodes was measured with a sapphire rod pyrometer, the output of which controlled the dc power supply. This assembly was enclosed within an evacuable chamber containing a quartz viewing window. The temperature of the specimen over its entire length could be scanned with a portable pyrometer through

Jan 1, 1965

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium' and to the tensile ductility of a-B titanium alloys.' These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.' The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.'-'* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By P. G. Shewmon, H. E. Collins

A study has been made to determine the sites at which sulfur adsorption occurs on copper surfaces. measurements were made of the relative torques, Ys, at the intersection of twin boundaries with surfaces near the three low-index orientations, i.e., (100), @lo), and 011), over a range of H2S/H2 ratios. HZS concerztvations j'ro~n 3 to 1500pp)n between 830" and 1050°C were used. It is concluded that sulfur adsorption occurved preferentially though not exclusively at edge sites near the (100) and (110) surfaces in the HzS range — 700 Ppm giving rise to negative torques near these orientations. Beyond this HzS range, adsorption occurred at all sites. Near the (111) surface, 7/y little with HzS concentration up to approxiwzately 75pptn. Above this range, the results indicate adsorption is occurring OH both terrace and edge sites. SCIENTIFIC interest in surfaces and their interactions with a gaseous environment dates back to the beginning of the 19th century. The scientific luminaries of that period—Faraday, Maxwell, Rayleigh, Dewar, and Gibbs—were already concerned about such processes. However, it has only been within the past several decades that adsorption on metal surfaces has been actively studied. This increased interest in adsorption has been brought about by the advent of new and improved experimental techniques and apparatus, e.g., ultrahigh vacuum, and field-emission and ion microscopes. However, most of the work done using these techniques has been carried out at low temperatures. When adsorption studies have been made at either low or high temperatures, they usually gave no indication of the particular surface orientations or type of sites on which adsorption was occurring. In the last few years, there have been a series of studies in which the surface tension, y,, and/or its derivative with respect to orientation, 7, have been studied as a function of orientation and atmosphere.'-7 Nearly all of the work on the relative torque,* ~/y, silver annealed in hydrogen and air.6 Recently Winterbottom and Gjostein" have used a modified and more accurate Mykurian method to determine the y plot of gold in hydrogen The only work in which T/~, has been measured over a range of chemical potentials for a given solute, p2, is that of Robertson and shewmon7 on the Cu-0 system. They measured T/Y, vs Po, (10"" to 10- l3 atm) at 1000°C in various mixtures of Hz0 and HZ. From this work they estimated the value of p2 at which one half of the surface sites are occupied with oxygen, pg, as being in the range 10- l6 to 10- l5 atm of oxygen. They also found that increasing Pa increased the magnitude of ~/y, near the (111) and (100) orientations. This indicates that oxygen is not adsorbed preferentially at step edges, but uniformly over all surface sites. In addition, they did one experiment on sulfur adsorption on copper surfaces, which indicated that sulfur adsorption decreases ~/y, near the (100) orientation, while not affecting ~/y, near the (111). This could be interpreted as indicating that sulfur adsorbs preferentially at step edges near the (100). In this paper the primary objective of the work has been to carry out a study of sulfur adsorption on copper surfaces over a range of temperatures and p,. In conjunction with this work, thermal grooving at grain boundaries has been examined as a method of determining the effect of sulfur adsorption on y,. METHODS Ideally, one would like to have information on the quantity of solute adsorbed on a surface and the types of sites at which it is absorbed as a function of p2. The total quantity adsorbed or the surface excess is given by the thermodynamic equation Thus data on the variation of y, with pz indicates the value of p2 at which adsorption becomes appreciable and the quantity adsorbed. The type of adsorption site is more difficult to deduce but information on this can be obtained from the variation of rz with 8, the angular deviation of the surface orientation. This is obtained from the thermodynamic equationlg Data on t and ys as functions of p2 have been obtained by the following methods. 1) Twin Boundary Grooving—By determining the effect of adsorption on the torque, 7, where T is the variation of surface energy, y,, with orientation, it is possible to obtain some indication as to the preferred sites of adsorption. Experimentally, the torque value measured is the relative torque, 7/ys The twin boundary grooving technique suggested by Mykura'' was used in this study to determine near the three low-index orientations— (loo), (110), and (111). Mykura's equation relates 7 /yS to measurements of the di-

Jan 1, 1967

By Frank W. Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength, consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig. 1 was drawn.

Jan 1, 1928

By Kung-Lee Wang, Brian W. Mackenzie, Warren E. Morrison, DeVerle P. Harris, George F. Sharrard

The term "mineral economics" is applied to a wide range of activities in the mineral industries. Earlier chapters have described the application of economic concepts to the mineral industries-supply, demand, conservation, tariffs, etc. The solution of mineral economics problems is often assisted by the application of quantitative methods. The purpose of this chapter is to describe a number of quantitative methods-econometric, operations research, and management science techniques-which find application in the analysis of mineral economics problems. These methods include input-output analysis, trend analysis, forecasting techniques, simulation, multivariate statistical analysis, mathematical programming, and market research techniques. The purpose of this introductory section is to provide a mineral economics framework for the application of these methods. Mineral economics is a subdivision of economics that is justified by a sufficient number of economic problems in the mineral industry requiring special experience and an unusual combination of skills. These problems are concerned with the conversion of minerals as geologic resources to minerals as economic goods. The mineral conversion process is outlined in Fig. 8.A.1. The physical occurrence of mineral deposits in nature and the market demand for mineral products in the economy provide the basic stimuli. The conversion process embodies a number of sequential stages-exploration, the development of mineral deposits, and mineral processing facilities and, consequently, productive activity to supply market demand. Changes in demand and the depletion of deposits illustrate the dynamics of the process. Mineral economics applies economic con-

Jan 1, 1976

By Robert A. Kinzie

PAGE Introduction.............334 Climate.............335 History............335 Geology.............341 Mining..............343 Shafts............343 Stations and Ore-Bins....345 Levels. Drifts. Cross-Cuts, Winzes. etc........347 Stoping Surface-Pits,......... 351 Underground Stoping........... 332 Chutes. Drilling. etc.....354 Tramming............. 358 Sampling. Maps and Assaying.........360 Labor.............361 Machinery.............362 Milling,..............362 Crushers.............366 Battery-Foundations...........368 Power (Water—Coal)...........373 Methods of Catching the Free Gold...374 Screens..............376 Apron-Plates,.......376 Concentration..........378 Clean-Up,.............378 Labor..............382 Costs..............382 Introduction. The Treadwell Group comprises five mines. four of which are situated on the northeast side of Douglas island. directly opposite the town of Juneau, and one about four miles back of Juneau. These mines are owned by four separate companies. but are all under the same general management. Those situated on Douglas island are : The Treadwell mine. owned by the Alaska Treadwell Gold Mining Co.. the Mexican mine. owned by the Alaska Mexican Gold Mining Co.; and the Ready Bullion and Seven-Hundred-Foot mines. owned by the Alaska United Gold Mining Co. The Juneau mine. owned by the

Jan 1, 1904

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

Solid-solubility limits at 1500°, l000q and 500°C for carbon, nitrogen, and oxygen in high-purity tantalum were determined by X-ray lattice-parameter methods. For carbon, the solubility was found to be 0.17 at. pct at 1500°C, and less than 0.07 at. pct at 1000°C. A nitrogen solubility of 3.70 at. pct at 1500° C decreases linearly with temperature to 2.75 at. pct at 1000°C, and 1.8 at. pct at 500°C. In the case of oxygen, the solubility was found to be 3.65 at. pct at 1500°C, 2.95 at. pct at 1000°C, and 2.5 at. pct at 500°C. The phases Ta2C, the low-temperature modification of Ta205, and Ta,N of unknown composition but which has a superlattice structure based upon the original bcc tantalum lattice have been identified as the initial precipitates in the respective systems. Metallographic methods were employed to verify the X-ray analyses. The etching behavior of Ta is discussed in terms of lattice i?rzperfections and precipitate phases. The excellent fabricability, high melting point, and nuclear properties of tantalum are responsible for interest in this refractory metal. Data on the solid solubility of the interstitial elements (oxygen, nitrogen, and carbon) in tantalum and on the precipitate phases are somewhat limited. The significant contributions are discussed below. Because the purity of electron-beam melted tantalum (only recently available) is considerably higher than that used in previous studies, the present investigation was initiated. Gebhardt et all-3 have investigated the tantalum-oxygen and tantalum-nitrogen systems with particular reference to the changes in physical properties and to the rates of reaction between these gases and the metal. The solubility of oxygen in tantalum was reported2 to be 3.7 at. pet at 1500°, 2.3 at. pet at 100O°C, and 1.4 at. pct at 750°C. Schonberg4 reported that several oxide phases (Ta40, Ta,O, TaO and Ta,05) exist while X-ray studies by Gebhardtl showed only two oxides, Ta,05 and an unidentified phase which was associated with a platelet-type precipitate. La-gergren and Magneli,' however, questioned the existence of compounds other than the two allotropic modifications of Ta,05 for the tantalum-oxygen system. In the case of nitrogen, the solubility was estab- lished by Gebhardt3 to be of the order of 7 at. pct at 1800°c. The solubility was reported to decrease rapidly with temperature, and, although no limits were established, a precipitate phase was observed by Gebhardt except when the high-nitrogen specimens were cooled very rapidly from the reaction temperature of 1800c. He reported the initial precipitate phase to be a tetragonal distortion of the bcc tantalum lattice while Schonberg6 reported the phase lowest in nitrogen Jo be a cubic super-lattice with a cell size of 10.11 A. Two other nitride phases, Ta,N and TaN, were reported; these appear to be isomor-phous with the carbides of tantalum. The tantalum-carbon system was investigated by Ellinger7 and by Lesser and Braurer. Two compounds, Ta,C and TaC, were reported to exist, each with a range of composition. The solubility of carbon in tantalum was found to be practically nil at all temperatures. Thus, of the interstitial elements which are present in small amounts in high-purity tantalum, carbon might be expected to form precipitates. The present investigation was initiated to obtain additional data on the solid-solubility limits of these interstitials at 1500°, 1000°, and 500' with particular emphasis on the distribution and the identification of the precipitate phases. EXPERIMENTAL WORK AND RESULTS In the present investigations of the solid solubility and of the precipitate phases in the systems tantalum-nitrogen, -oxygen, and -carbon, high-purity tantalum was reacted with high-purity gases, homogenized at 1800°c, and annealed at and quenched from 1500°, 1000,

Jan 1, 1962

By W. B. Plank

I HAVE been asked by the Chairman of the Engineering Education Committee to outline what the engineering colleges would like the mining companies to do with the young engineer just, out of college. It has been suggested that, because my own personal experience has been almost entirely within the coal industry, I handle this subject from that view- point. Many thoughtful engineering educators are today wondering what effect the present employment policies of many industrial companies are going to have on the young man just starting out in his profession. Since before the World War large industrial concerns, such as those in the electrical and mechanical industries, have gone to the colleges to interview 'likely graduates until today there has developed in most of our engineering colleges, especially in the eastern part of the country, what appears to be a lively competition on the part of these companies in bidding for the young graduate engineer. The employers of mining engineers, with one or two exceptions, have not yet begun to enter this competition. It remains to be seen how serious this situation will become, how it will affect the training of other engineers, and what effect, if any, it will have on the mind of the young man about to enter college who may be inclined to take up mining engineering, but who gains the impression from this well advertised employment service just mentioned that there is no opportunity for him in the mineral industry as com- pared with the opportunities offered in say civil, mechanical, and electrical engineering.

Jan 1, 1929

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company's Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By M. J. Marcinkowski, Gordon E. Lakso

An extensive investigation has been made of the deformation behavior associated with the Fe3Si super-lattice using transmission electron microscopy techniques. Above 243°K the stress-strain curve exhibits three stages. Stage I occurs at a very low stress level and is related to the generation of perfect superlat-tice dislocations. Stage II is characterized by an extremely rapid rate of work hardening and is associated with the Taylor type locking of these superlattice dislocations. Finally Stage III is related to dynamic recovery processes since the work hardening rate is very small. Below 243ºK, only Stage I is observed, but it occurs at a much higher stress level. This latter observation is related to the generation of imperfect dislocations in Stage I with the consequent production of second nearest neighbor antiphase boundaries. The reason for this is that insufficient thermal energy is available at these low temperatures to generate the complete and perfect superlattice dislocations. It has been shown that the fully ordered FeCo alloys, i.e., those possessing the B2 type structure, exhibit three distinct stages of work hardening whereas the corresponding disordered alloys show only one.&apos;" This difference in behavior between the disordered and ordered alloys has been attributed to the fact that dislocations in the former case travel only as ordinary 1/2ao(111) types whereas in the latter case the move through the lattice as coupled 1/2a0(111) dislocations separated by an antiphase boundary (APB), i.e., the so-called superlattice dislocation. Although some preliminary work has been carried out concerning plastic deformation in ordered alloys possessing the DO3 type superlattice,3 no detailed analysis similar to that described in Refs. 1 and 2 has been attempted. Specifically, it has been suggested that the superlattice dislocation in this particular type structure should consist of four ordinary 1/2ao<111> types bound together by first and second nearest-neighbor APB&apos;s. Fe3A1 and Fe3Si are the two classic alloys possessing the DO3 type lattice; however, because of the somewhat higher ordering energies associated with the FesSi alloy, which in turn assures that dislocations will travel through the lattice as perfect superlattice dislocations under at least some conditions, it was chosen for the present investigation. Because of the extreme brittleness of Fe3Si, all deformation was done in compression. Stress-strain curves were obtained using both polycrystalline samples as well as single crystals. In the latter case the crystals were oriented so that deformation could be controlled either by single or double slip. They were then wafered parallel to and at various angles to the operative slip planes. These wafers were in turn examined by transmission electron microscopy (TEM) techniques in order to determine the extent of the interaction from the dislocation configuration contained therein. EXPERIMENTAL PROCEDURE The alloys used in this investigation were arc melted under helium from electrolytic iron of greater than 99.90 wt pct purity and transistor grade silicon of 99.99 wt pct purity. A typical analysis of interstitial impurities showed 120 ppm 0, 15 ppm N, and 65 ppm C Because of the extremely low ductility of the Fe3Si alloys, it was necessary to spark cut 0.230-in. diam polycrystalline cylinders 0.400 in. long from arc-melted fingers using a thin-walled brass tube as a cutting tool. The polycrystalline alloys could not be recrystallized since very little strain was induced in preparation. However they were annealed at 1273°C for 15 min in evacuated vycor capsules to relieve any cooling stresses that may have developed during solidification and then air cooled. The resulting grain size of the alloy was 0.50 mm. According to warlimont4 1273ºC is just within the single phase field where FesSi possesses the DO3 type lattice. In addition because of this high critical ordering tem-ature, air cooling from this temperature was believed sufficient to fully order all of the Fe3Si samples used in the present investigation. For the same reason, no attempt was made to achieve any degree of disorder by quenching. In fact, rapid quenching from 1123°K caused cracking. Such cracking was first suggested by sato5 with respect to the experimental observations of Glaser and Ivanick.6 Single crystal compression specimens were spark cut from single crystal ingots grown in a Bridgman type furnace. The iron and silicon for the crystals was prealloyed by arc-melting two 130-g buttons which were cut into small pieces before remelting in the furnace. This procedure resulted in a long-range inhomogeneity of 0.5 at. pct Si between the top and bottom of the 2-in.-long single crystal ingot, which was assumed to be negligible in the present investigation. The single crystals, after orienting and spark-cutting, were about 0.37 in. by 0.37 in. in cross section and about 0.5 in. long. True stress-strain curves were obtained using an Instron Tensile Testing machine in conjunction with techniques described previously. 1,7 The strain rate was 0.05 in. per in. per min. Prior to testing, the ends of all the compression cylinders were hand polished using a special jig to insure parallelism after which the sides of the samples were electrochemically polished to eliminate stress risers and to facilitate slip line observations. Test temperatures between 77" and 823°K were obtained using various cooling and heating media as described in Ref. 7 while at the upper end of this temperature range, a mixture of equal

Jan 1, 1970

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman&apos; for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man&apos; has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman&apos;s model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman&apos; derives the constraint on the linked-central force distortion on the basis of application of Pauling&apos;s relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By M. H. Harris

A solution has been obtained to the problem of calculating flow into a cased and perforated well. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. Computer experimentation indicated that the results are within 3 per cent of the exact solution. Computed results are presented as an apparent skin effect, on a series of dimensionless working curves. Productivity ratios can be rapidly calculated from these data for the wide range of wellbore and reservoir properties actually encountered in field practice. Any reasonable vertical unisotropy ratio can be included in the computation. Productivities can be calculated for wells perforated in a regular pattern, a single horizontal plane or a vertical line on one side of the casing. Solutions for asymmetrical perforation patterns can he easily obtained from the working curves. Solutions for flow into sells completed with a horizontal notch are also provided. Results show that productivity can be increased by extending perforation penetration. This is especially true for shallow penetrations. The highest productivity is obtained when perforations are arranged in horizontal planes, as opposed to a vertical line on one side of the casing. Four or five perforations in one plane will approach the maximum productivity. The effect of perforation hole diameter is small, and is rioticeable only in shallow penetrations. INTRODUCTION The perforating method of well completion has been successfully and widely used in most producing areas. In the past, the desired perforation results were achieved by simply shooting numerous large holes in the casing. A perforating scheme for an area, or particular well, was established by evaluating two types of experimental data: the well flow index and the productivity ratio.&apos; 3 The well flow index test is a means of determining the relative flow capacity of perforations in a linear system. This test also gives information on the perforation size, shape and hole damage which can be expected under well-bore conditions. However, relative flow data from this test cannot be accurately tarnsformed into the radial wellbore system. Thus, no true indication of the productive capacity of a perforated well can be obtained from the well flow index test. A well productivity ratio is derived from electrolytic models built to simulate perforated wells. Available productivity ratio data 2,3 are limited in that all important variables are not extensively evaluated. For example, data are limited to well radii of 3 and 6 in., and to maximum perforation penetration of 1 ft. Practically no information is available on the pattern of flow into a perforation. The effect of various perforation patterns on well productivity has not yet been determined and the effect of perforation diameter has not been thoroughly studied. Also, it will be shown that this type of electrolytic model data is probably in error by as much as 10 per cent or more. Modern completion techniques such as limited-entry perforating, single-plane fracturing, steam and hot air injection and chemical consolidation of incompetent formations all rely on injection and/or production from a limited type of completion. These completions may consist of several high-capacity perforations or a horizontal notch which is equivalent to an infinite number of perforations in one plane. Proper design of these new completion techniques requires, in part, accurate estimates of a well&apos;s productive capacity. Data on perforated and notched well productivity have been determined in this investigation. Results are presented as a function of the pertinent variables. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. DESCRIPTION OF PROBLEM PRACTICAL APPLICATION The computed results can be applied to wells which meet several general specifications. An external drainage radius of the well must be known or assumed, but the well need not be drilled on a regular pattern. The well must be cased and cemented through the entire producing interval. And, the casing must be perforated with one or more horizontal planes of perforations. The perforation pattern itself must conform to three geometrical requirements. 1. The perforations in a plane must divide the plane into equal angular segments (Fig. 1). Four perforations per plane would be 90" apart. 2. Perforations in a plane must be directly above or beneath perforations in adjacent planes. For two shots per plane, perforations would lie in the BB&apos; plane (Fig. 1). 3. Horizontal planes must have equal vertical spacing and be separated from the top and bottom of the formation by one half the spacing interval. Single planes of perforations should be in the middle of the formation. This is shown in Fig. 2 where h is the formation thickness in a single plane conlpletion or the spacnig interval in a multiple plane completion. The spacing interval at the top and bottom of the formation may vary somewhat without causing an appreciable error in the productivity calculation if the formation is reasonably thick and there are many horizontal planes of perforations. A special provision has been made to calculate the productivity ratios of wells with uneven spacing intervals, or for the case where a single plane of perfora-

Jan 1, 1967

By Edward Halse

THE occasional occurrence in metalliferous veins of rounded fragments of rock, matrix or ore, lying loose, embedded in clay, or enclosed in some kind of cement, may be attributed to four causes:¬ I. They have been washed in from the surface, or from an upper portion of the vein. II. They are of concretionary origin. III. They have been produced by movements in the country-rock or in the walls of the vein. IV. They have been found in situ, by the upward, downward or lateral flow of water in the vein itself. In this paper the word " conglomerate " is confined to a rock composed of rounded fragments or pebbles cemented together, as distinguished from a " breccia," in which the rock-fragments are angular. I. BOULDERS AND PEBBLES WHICH HAVE BEEN WASHED IN FROM THE SURFACE, OR FROM AN UPPER PORTION OF THE VEIN. In this type it is presupposed that the vein at onetime com¬municated by a fissure or open space with the surface, or with the upper portion from whence the fragments have been washed. One well-authenticated occurrence was described long ago by Fournet. Owing, no doubt, to later dislocations in the lode, pebbles from an old alluvium and sands containing titaniferous iron, as well as fragments of wood, were found in a vein at Huelgoët, in France. "Toutes les parties tendres du filon de Pranal ou ces pédnomènes sont les plus prononcés ont été excavés jusqu&apos;a d&apos;assez grandee profondeurs par l&apos;impétuosité des torrents, qui ont deposé la matière alluviale."1

Jul 1, 1905

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

By Frederick Laist

About six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electronegative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection—1 mg. or less per liter. A pure zinc is soluble only with difficulty in sulfuric acid; an impure zinc dissolves very readily. Electrolytic zinc deposited from pure solutions is, of course, extremely pure and dissolves only about one-fiftieth

Jan 1, 1921

By A. C. Boyle

PaGE I. Introduction.........68 II. Location of the District,....... • 70 .. III. Stratigraphy...........73 Description of the Rocks.......73 Triassic Eruptives (Andesite Flows and Tuffs) ....73 Triassic Sediments (Shales and Slates)..75 Areal Geology ............75 Structure...-.......76 Folds............. 76 Faults..........79 Shear ...........80 Intrusives..........81 Alaskite Dike.........81 Andesitic Intrusion.......82 IV. PetrogRaphy of thE Rock Types......83 Andesite Flows.........84 Tuff 8...........84 Andesite Tuff........84 Rhyolite Tuff.....-.......85 Alaskite-Porphyry.......89 Andesite Dike........91 V. Description of the Mines......92 VI. Metalliferous Deposits ........ 95 Character of the Ores...........97 Mineralogy of the Ores.......97 Metallic Minerals.......97 Microscopic Character of the Ores...98 Secondary Enrichment....... 103 Genesis of the Ores ...........104 VII. The Sulphate Deposits.......109 Gypsum ..... HO Anhydrite......... ,... 110 Barite............ 110 Origin. with special reference to Gypsum....111 VIII. Summary.............. 113 IX. BIblYogRaphY.............114

Jan 1, 1915